* PROBLEM: kernel panic
@ 2007-10-13 22:48 Scott Petler
2007-10-14 20:24 ` Trond Myklebust
0 siblings, 1 reply; 9+ messages in thread
From: Scott Petler @ 2007-10-13 22:48 UTC (permalink / raw)
To: linux-kernel
Machine lockup with caps lock/num lock flashing or complete reboot/panic.
I get various lockup issues with this kernel, (2.6.23 also similar
problem). I had problems getting e1000 lan module to work (it was fine
in 2.6.21.5). I disabled it and installed a different lan card that
seems to work "better".
Dual head machine 1GB RAM, nvidia driver x86-100.14.19
Here is output of ver_linux:
---------------------------------------------------------------------------------------------------------------------------------------------
Linux zion 2.6.23-rc9 #3 Fri Oct 12 18:27:56 PDT 2007 i686 GNU/Linux
Gnu C 4.1.2
Gnu make 3.81
binutils 2.17
util-linux 2.12r
mount 2.12r
module-init-tools 3.3-pre2
e2fsprogs 1.40-WIP
Linux C Library 3.6
Dynamic linker (ldd) 2.3.6
Procps 3.2.7
Net-tools 1.60
Console-tools 0.2.3
Sh-utils 5.97
udev 105
Modules Loaded nfs lockd sunrpc nvidia i2c_core af_packet ipv6
capability commoncap ppdev lp ac battery dm_mod e1000 loop snd_intel8x0
snd_ac97_codec ac97_bus snd_pcm_oss snd_mixer_oss snd_pcm snd_timer
parport_pc button parport snd 8250_pnp 8250 serial_core soundcore shpchp
pci_hotplug snd_page_alloc rng_core floppy intel_agp agpgart rtc sg
evdev sr_mod usbhid sd_mod ata_piix 8139too ata_generic ehci_hcd
uhci_hcd mii bitrev crc32 libata generic usbcore thermal processor fan
unix ext3 jbd piix ide_disk ide_cd cdrom ide_scsi scsi_mod ide_core
---------------------------------------------------------------------------------------------------------------------------------------------
Here is output from syslog as it went down:
Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
zion kernel: Oops: 0002 [#1]
Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
zion kernel: CPU: 0
Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
zion kernel: EIP: 0060:[<e1168fde>] Tainted: P VLI
Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
zion kernel: EFLAGS: 00010206 (2.6.23-rc9 #3)
Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
zion kernel: EIP is at 0xe1168fde
Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
zion kernel: esi: f8f34700 edi: 00000000 ebp: 00000001 esp: e7cf3e00
Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
zion kernel: ds: 007b es: 007b fs: 0000 gs: 0033 ss: 0068
Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
zion kernel: Process firefox-bin (pid: 8397, ti=e7cf2000 task=f258ca90
task.ti=e
7cf2000)
Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
zion kernel: Stack: f8f18eb7 c01367f6 e7cf3e48 000003e8 000003e8
ed3e97c0 f1f6db
9c f1f6db9c
Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
zion kernel: e7cf3f54 f8f60ec2 0004257b 00000000 00000000
f1f037dc e7cf3f
54 c01563d0
Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
zion kernel: 019cc780 e7cf3eb0 c0155a63 dfff38c0 c014e001
019cc780 f1f037
dc dfe0ecf4
Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
zion kernel: Call Trace:
Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
zion kernel: [<f8f18eb7>] rpcauth_lookupcred+0x63/0x87 [sunrpc]
Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
zion kernel: [<c01367f6>] pagevec_lookup+0x1c/0x22
Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
zion kernel: [<f8f60ec2>] nfs_permission+0xab/0x183 [nfs]
Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
zion kernel: [<c01563d0>] __d_lookup+0x8b/0xbf
Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
zion kernel: [<c0155a63>] dput+0x15/0xcb
Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
zion kernel: [<f8f60e17>] nfs_permission+0x0/0x183 [nfs]
Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
zion kernel: [<c014f648>] __link_path_walk+0x11c/0xa79
Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
zion kernel: [<c0102ff8>] setup_sigcontext+0x104/0x187
Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
zion kernel: [<c014ffe7>] link_path_walk+0x42/0xaf
Read from remote host 192.168.1.175: Connection reset by peer
Connection to 192.168.1.175 closed.
Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
zion kernel: [<c014de5a>] permission+0x9e/0xdb
------------------------------------------------------------------------------------------------------------------------------------------------
/proc/cpuinfo
processor : 0
vendor_id : GenuineIntel
cpu family : 15
model : 2
model name : Intel(R) Pentium(R) 4 CPU 2.40GHz
stepping : 7
cpu MHz : 2411.749
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe pebs
bts sync_rdtsc cid xtpr
bogomips : 4826.95
clflush size : 64
----------------------------------------------------------------------------------------------------------------------------------------------------
/proc/modules
nfs 120816 1 - Live 0xf8f3a000
lockd 59656 2 nfs, Live 0xf8d7a000
sunrpc 154524 6 nfs,lockd, Live 0xf8f13000
nvidia 6212112 24 - Live 0xf9448000 (P)
i2c_core 23312 1 nvidia, Live 0xf8d4a000
af_packet 20104 2 - Live 0xf8d51000
ipv6 222052 10 - Live 0xf8d8b000
capability 5000 0 - Live 0xf8d39000
commoncap 7296 1 capability, Live 0xf886a000
ppdev 8964 0 - Live 0xf8d35000
lp 11204 0 - Live 0xf8d31000
ac 5764 0 - Live 0xf89fa000
battery 12424 0 - Live 0xf89ff000
dm_mod 49728 0 - Live 0xf8d3c000
e1000 111424 0 - Live 0xf8a2c000
loop 16772 0 - Live 0xf89ee000
snd_intel8x0 31260 0 - Live 0xf8a05000
snd_ac97_codec 90784 1 snd_intel8x0, Live 0xf8a4a000
ac97_bus 2432 1 snd_ac97_codec, Live 0xf88ce000
snd_pcm_oss 38560 0 - Live 0xf8a21000
snd_mixer_oss 15360 1 snd_pcm_oss, Live 0xf89a5000
snd_pcm 68872 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss, Live 0xf8a0f000
snd_timer 19972 1 snd_pcm, Live 0xf89f4000
parport_pc 33572 1 - Live 0xf89ca000
button 8464 0 - Live 0xf89c6000
parport 33096 3 ppdev,lp,parport_pc, Live 0xf89e2000
snd 46820 6
snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer,
Live 0xf89d5000
8250_pnp 9728 0 - Live 0xf89aa000
8250 21748 1 8250_pnp, Live 0xf89bf000
serial_core 19072 1 8250, Live 0xf89b9000
soundcore 7392 1 snd, Live 0xf895d000
shpchp 30996 0 - Live 0xf89b0000
pci_hotplug 13960 1 shpchp, Live 0xf8963000
snd_page_alloc 10248 2 snd_intel8x0,snd_pcm, Live 0xf89a1000
rng_core 5252 0 - Live 0xf8960000
floppy 51876 0 - Live 0xf8971000
intel_agp 23572 1 - Live 0xf894d000
agpgart 31152 2 nvidia,intel_agp, Live 0xf8968000
rtc 11800 0 - Live 0xf8949000
sg 31644 0 - Live 0xf8954000
evdev 9600 1 - Live 0xf890b000
sr_mod 15140 0 - Live 0xf8906000
usbhid 26496 0 - Live 0xf8941000
sd_mod 26000 3 - Live 0xf8939000
ata_piix 17028 2 - Live 0xf8933000
8139too 23552 0 - Live 0xf892c000
ata_generic 7812 0 - Live 0xf881b000
ehci_hcd 27916 0 - Live 0xf88f1000
uhci_hcd 21900 0 - Live 0xf88f9000
mii 5504 1 8139too, Live 0xf88ee000
bitrev 2176 1 8139too, Live 0xf88cc000
crc32 4224 1 8139too, Live 0xf886d000
libata 111796 2 ata_piix,ata_generic, Live 0xf890f000
generic 4996 0 [permanent], Live 0xf8867000
usbcore 122264 4 usbhid,ehci_hcd,uhci_hcd, Live 0xf88ad000
thermal 15644 0 - Live 0xf8878000
processor 21152 1 thermal, Live 0xf8830000
fan 5252 0 - Live 0xf881e000
unix 24880 654 - Live 0xf8870000
ext3 118024 1 - Live 0xf88d0000
jbd 49960 1 ext3, Live 0xf889f000
piix 8836 0 [permanent], Live 0xf882c000
ide_disk 16000 0 - Live 0xf8827000
ide_cd 36000 0 - Live 0xf885d000
cdrom 32800 2 sr_mod,ide_cd, Live 0xf8853000
ide_scsi 16392 0 - Live 0xf8821000
scsi_mod 132360 5 sg,sr_mod,sd_mod,libata,ide_scsi, Live 0xf887d000
ide_core 106704 5 generic,piix,ide_disk,ide_cd,ide_scsi, Live 0xf8837000
------------------------------------------------------------------------------------------------------------------------------------------------
/proc/ioports
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-006f : keyboard
0070-0077 : rtc
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : 0000:00:1f.2
0170-0177 : libata
01f0-01f7 : 0000:00:1f.2
01f0-01f7 : libata
02f8-02ff : serial
0376-0376 : 0000:00:1f.2
0376-0376 : libata
0378-037a : parport0
03c0-03df : vga+
03f2-03f5 : floppy
03f6-03f6 : 0000:00:1f.2
03f6-03f6 : libata
03f7-03f7 : floppy DIR
03f8-03ff : serial
0cf8-0cff : PCI conf1
1000-107f : 0000:00:1f.0
1000-1003 : ACPI PM1a_EVT_BLK
1004-1005 : ACPI PM1a_CNT_BLK
1008-100b : ACPI PM_TMR
1028-102f : ACPI GPE0_BLK
1080-10bf : 0000:00:1f.0
1400-141f : 0000:00:1f.3
a000-afff : PCI Bus #02
a000-a0ff : 0000:02:01.0
a000-a0ff : 8139too
b000-b01f : 0000:00:1d.1
b000-b01f : uhci_hcd
b400-b41f : 0000:00:1d.2
b400-b41f : uhci_hcd
b800-b81f : 0000:00:1d.3
b800-b81f : uhci_hcd
bc00-bc1f : 0000:00:1d.0
bc00-bc1f : uhci_hcd
d800-d8ff : 0000:00:1f.5
d800-d8ff : Intel ICH5
dc00-dc3f : 0000:00:1f.5
dc00-dc3f : Intel ICH5
f000-f00f : 0000:00:1f.2
f000-f00f : libata
-----------------------------------------------------------------------------------------------------------------------------------------------
/proc/iomem
00000000-0009f7ff : System RAM
0009f800-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000d0000-000d7fff : pnp 00:00
000f0000-000fffff : System ROM
00100000-3ffeffff : System RAM
00100000-00287ed7 : Kernel code
00287ed8-003224df : Kernel data
3fff0000-3fff2fff : ACPI Non-volatile Storage
3fff3000-3fffffff : ACPI Tables
d0000000-dfffffff : PCI Bus #01
d0000000-dfffffff : 0000:01:00.0
e0000000-e7ffffff : 0000:00:00.0
e8000000-ebffffff : PCI Bus #02
e8000000-ebffffff : 0000:02:04.0
ec000000-eeffffff : PCI Bus #01
ec000000-ecffffff : 0000:01:00.0
ec000000-ecffffff : nvidia
ed000000-edffffff : 0000:01:00.0
ee000000-ee01ffff : 0000:01:00.0
ef000000-ef0fffff : PCI Bus #02
ef000000-ef0000ff : 0000:02:01.0
ef000000-ef0000ff : 8139too
ef100000-ef1003ff : 0000:00:1d.7
ef100000-ef1003ff : ehci_hcd
ef101000-ef1011ff : 0000:00:1f.5
ef101000-ef1011ff : Intel ICH5
ef102000-ef1020ff : 0000:00:1f.5
ef102000-ef1020ff : Intel ICH5
fec00000-ffffffff : reserved
~
----------------------------------------------------------------------------------------------------------------------------------------------
lspci -vvv
00:00.0 Host bridge: Intel Corporation 82865G/PE/P DRAM
Controller/Host-Hub Interface (rev 02)
Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Capabilities: [e4] Vendor Specific Information
Capabilities: [a0] AGP version 3.0
Status: RQ=32 Iso- ArqSz=2 Cal=2 SBA+ ITACoh- GART64-
HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=2 SBA+ AGP+ GART64- 64bit- FW-
Rate=x8
00:01.0 PCI bridge: Intel Corporation 82865G/PE/P PCI to AGP Controller
(rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: ec000000-eeffffff
Prefetchable memory behind bridge: d0000000-dfffffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
00:1d.0 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
UHCI Controller #1 (rev 02) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology GA-8IPE1000/8KNXP motherboard
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at bc00 [size=32]
00:1d.1 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
UHCI Controller #2 (rev 02) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE)
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at b000 [size=32]
00:1d.2 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
UHCI Controller #3 (rev 02) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE)
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at b400 [size=32]
00:1d.3 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
UHCI Controller #4 (rev 02) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE)
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at b800 [size=32]
00:1d.7 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2
EHCI Controller (rev 02) (prog-if 20 [EHCI])
Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 0: Memory at ef100000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev c2) (prog-if
00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: ef000000-ef0fffff
Prefetchable memory behind bridge: e8000000-ebffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC
Interface Bridge (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.2 IDE interface: Intel Corporation 82801EB (ICH5) SATA Controller
(rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE)
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at f000 [size=16]
00:1f.3 SMBus: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus
Controller (rev 02)
Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE)
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 9
Region 4: I/O ports at 1400 [size=32]
00:1f.5 Multimedia audio controller: Intel Corporation 82801EB/ER
(ICH5/ICH5R) AC'97 Audio Controller (rev 02)
Subsystem: Giga-byte Technology GA-8IPE1000/8KNXP motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 0: I/O ports at d800 [size=256]
Region 1: I/O ports at dc00 [size=64]
Region 2: Memory at ef101000 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at ef102000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: nVidia Corporation NV43 [GeForce
6600/GeForce 6600 GT] (rev a2) (prog-if 00 [VGA])
Subsystem: XFX Pine Group Inc. GeForce 6600 GT AGP 128MB DDR3
DUAL DVI TV
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 248 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 16
Region 0: Memory at ec000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 2: Memory at ed000000 (32-bit, non-prefetchable) [size=16M]
[virtual] Expansion ROM at ee000000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 3.0
Status: RQ=256 Iso- ArqSz=0 Cal=3 SBA+ ITACoh- GART64-
HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=32 ArqSz=2 Cal=0 SBA+ AGP+ GART64- 64bit-
FW- Rate=x8
02:01.0 Ethernet controller: D-Link System Inc RTL8139 Ethernet (rev 10)
Subsystem: D-Link System Inc DFE-530TX+ 10/100 Ethernet Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at a000 [size=256]
Region 1: Memory at ef000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:04.0 Multimedia video controller: Internext Compression Inc iTVC16
(CX23416) MPEG-2 Encoder (rev 01)
Subsystem: Hauppauge computer works Inc. WinTV PVR 150
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (32000ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
--------------------------------------------------------------------------------------------------------------------------------------------
/proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: ATA Model: HDS722516VLSA80 Rev: V34O
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi1 Channel: 00 Id: 00 Lun: 00
Vendor: SONY Model: CD-ROM CDU5211 Rev: YYS7
Type: CD-ROM ANSI SCSI revision: 05
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: PROBLEM: kernel panic
2007-10-13 22:48 PROBLEM: kernel panic Scott Petler
@ 2007-10-14 20:24 ` Trond Myklebust
2007-10-14 20:44 ` Scott Petler
0 siblings, 1 reply; 9+ messages in thread
From: Trond Myklebust @ 2007-10-14 20:24 UTC (permalink / raw)
To: Scott Petler; +Cc: linux-kernel
On Sat, 2007-10-13 at 15:48 -0700, Scott Petler wrote:
> Machine lockup with caps lock/num lock flashing or complete reboot/panic.
>
> I get various lockup issues with this kernel, (2.6.23 also similar
> problem). I had problems getting e1000 lan module to work (it was fine
> in 2.6.21.5). I disabled it and installed a different lan card that
> seems to work "better".
>
> Dual head machine 1GB RAM, nvidia driver x86-100.14.19
Are you able to repeat this Oops _without_ the nvidia driver?
Also, please provide the output from /proc/mounts
Cheers
Trond
> Here is output of ver_linux:
> ---------------------------------------------------------------------------------------------------------------------------------------------
>
> Linux zion 2.6.23-rc9 #3 Fri Oct 12 18:27:56 PDT 2007 i686 GNU/Linux
>
> Gnu C 4.1.2
> Gnu make 3.81
> binutils 2.17
> util-linux 2.12r
> mount 2.12r
> module-init-tools 3.3-pre2
> e2fsprogs 1.40-WIP
> Linux C Library 3.6
> Dynamic linker (ldd) 2.3.6
> Procps 3.2.7
> Net-tools 1.60
> Console-tools 0.2.3
> Sh-utils 5.97
> udev 105
> Modules Loaded nfs lockd sunrpc nvidia i2c_core af_packet ipv6
> capability commoncap ppdev lp ac battery dm_mod e1000 loop snd_intel8x0
> snd_ac97_codec ac97_bus snd_pcm_oss snd_mixer_oss snd_pcm snd_timer
> parport_pc button parport snd 8250_pnp 8250 serial_core soundcore shpchp
> pci_hotplug snd_page_alloc rng_core floppy intel_agp agpgart rtc sg
> evdev sr_mod usbhid sd_mod ata_piix 8139too ata_generic ehci_hcd
> uhci_hcd mii bitrev crc32 libata generic usbcore thermal processor fan
> unix ext3 jbd piix ide_disk ide_cd cdrom ide_scsi scsi_mod ide_core
> ---------------------------------------------------------------------------------------------------------------------------------------------
>
> Here is output from syslog as it went down:
>
> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
> zion kernel: Oops: 0002 [#1]
>
> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
> zion kernel: CPU: 0
>
> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
> zion kernel: EIP: 0060:[<e1168fde>] Tainted: P VLI
>
> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
> zion kernel: EFLAGS: 00010206 (2.6.23-rc9 #3)
>
> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
> zion kernel: EIP is at 0xe1168fde
>
> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
> zion kernel: esi: f8f34700 edi: 00000000 ebp: 00000001 esp: e7cf3e00
>
> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
> zion kernel: ds: 007b es: 007b fs: 0000 gs: 0033 ss: 0068
>
> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
> zion kernel: Process firefox-bin (pid: 8397, ti=e7cf2000 task=f258ca90
> task.ti=e
> 7cf2000)
>
> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
> zion kernel: Stack: f8f18eb7 c01367f6 e7cf3e48 000003e8 000003e8
> ed3e97c0 f1f6db
> 9c f1f6db9c
>
> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
> zion kernel: e7cf3f54 f8f60ec2 0004257b 00000000 00000000
> f1f037dc e7cf3f
> 54 c01563d0
>
> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
> zion kernel: 019cc780 e7cf3eb0 c0155a63 dfff38c0 c014e001
> 019cc780 f1f037
> dc dfe0ecf4
>
> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
> zion kernel: Call Trace:
>
> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
> zion kernel: [<f8f18eb7>] rpcauth_lookupcred+0x63/0x87 [sunrpc]
>
> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
> zion kernel: [<c01367f6>] pagevec_lookup+0x1c/0x22
>
> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
> zion kernel: [<f8f60ec2>] nfs_permission+0xab/0x183 [nfs]
>
> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
> zion kernel: [<c01563d0>] __d_lookup+0x8b/0xbf
>
> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
> zion kernel: [<c0155a63>] dput+0x15/0xcb
>
> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
> zion kernel: [<f8f60e17>] nfs_permission+0x0/0x183 [nfs]
> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
> zion kernel: [<c014f648>] __link_path_walk+0x11c/0xa79
>
> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
> zion kernel: [<c0102ff8>] setup_sigcontext+0x104/0x187
>
> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
> zion kernel: [<c014ffe7>] link_path_walk+0x42/0xaf
> Read from remote host 192.168.1.175: Connection reset by peer
> Connection to 192.168.1.175 closed.
>
> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
> zion kernel: [<c014de5a>] permission+0x9e/0xdb
>
> ------------------------------------------------------------------------------------------------------------------------------------------------
> /proc/cpuinfo
>
> processor : 0
> vendor_id : GenuineIntel
> cpu family : 15
> model : 2
> model name : Intel(R) Pentium(R) 4 CPU 2.40GHz
> stepping : 7
> cpu MHz : 2411.749
> cache size : 512 KB
> fdiv_bug : no
> hlt_bug : no
> f00f_bug : no
> coma_bug : no
> fpu : yes
> fpu_exception : yes
> cpuid level : 2
> wp : yes
> flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
> mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe pebs
> bts sync_rdtsc cid xtpr
> bogomips : 4826.95
> clflush size : 64
>
> ----------------------------------------------------------------------------------------------------------------------------------------------------
> /proc/modules
>
> nfs 120816 1 - Live 0xf8f3a000
> lockd 59656 2 nfs, Live 0xf8d7a000
> sunrpc 154524 6 nfs,lockd, Live 0xf8f13000
> nvidia 6212112 24 - Live 0xf9448000 (P)
> i2c_core 23312 1 nvidia, Live 0xf8d4a000
> af_packet 20104 2 - Live 0xf8d51000
> ipv6 222052 10 - Live 0xf8d8b000
> capability 5000 0 - Live 0xf8d39000
> commoncap 7296 1 capability, Live 0xf886a000
> ppdev 8964 0 - Live 0xf8d35000
> lp 11204 0 - Live 0xf8d31000
> ac 5764 0 - Live 0xf89fa000
> battery 12424 0 - Live 0xf89ff000
> dm_mod 49728 0 - Live 0xf8d3c000
> e1000 111424 0 - Live 0xf8a2c000
> loop 16772 0 - Live 0xf89ee000
> snd_intel8x0 31260 0 - Live 0xf8a05000
> snd_ac97_codec 90784 1 snd_intel8x0, Live 0xf8a4a000
> ac97_bus 2432 1 snd_ac97_codec, Live 0xf88ce000
> snd_pcm_oss 38560 0 - Live 0xf8a21000
> snd_mixer_oss 15360 1 snd_pcm_oss, Live 0xf89a5000
> snd_pcm 68872 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss, Live 0xf8a0f000
> snd_timer 19972 1 snd_pcm, Live 0xf89f4000
> parport_pc 33572 1 - Live 0xf89ca000
> button 8464 0 - Live 0xf89c6000
> parport 33096 3 ppdev,lp,parport_pc, Live 0xf89e2000
> snd 46820 6
> snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer,
> Live 0xf89d5000
> 8250_pnp 9728 0 - Live 0xf89aa000
> 8250 21748 1 8250_pnp, Live 0xf89bf000
> serial_core 19072 1 8250, Live 0xf89b9000
> soundcore 7392 1 snd, Live 0xf895d000
> shpchp 30996 0 - Live 0xf89b0000
> pci_hotplug 13960 1 shpchp, Live 0xf8963000
> snd_page_alloc 10248 2 snd_intel8x0,snd_pcm, Live 0xf89a1000
> rng_core 5252 0 - Live 0xf8960000
> floppy 51876 0 - Live 0xf8971000
> intel_agp 23572 1 - Live 0xf894d000
> agpgart 31152 2 nvidia,intel_agp, Live 0xf8968000
> rtc 11800 0 - Live 0xf8949000
> sg 31644 0 - Live 0xf8954000
> evdev 9600 1 - Live 0xf890b000
> sr_mod 15140 0 - Live 0xf8906000
> usbhid 26496 0 - Live 0xf8941000
> sd_mod 26000 3 - Live 0xf8939000
> ata_piix 17028 2 - Live 0xf8933000
> 8139too 23552 0 - Live 0xf892c000
> ata_generic 7812 0 - Live 0xf881b000
> ehci_hcd 27916 0 - Live 0xf88f1000
> uhci_hcd 21900 0 - Live 0xf88f9000
> mii 5504 1 8139too, Live 0xf88ee000
> bitrev 2176 1 8139too, Live 0xf88cc000
> crc32 4224 1 8139too, Live 0xf886d000
> libata 111796 2 ata_piix,ata_generic, Live 0xf890f000
> generic 4996 0 [permanent], Live 0xf8867000
> usbcore 122264 4 usbhid,ehci_hcd,uhci_hcd, Live 0xf88ad000
> thermal 15644 0 - Live 0xf8878000
> processor 21152 1 thermal, Live 0xf8830000
> fan 5252 0 - Live 0xf881e000
> unix 24880 654 - Live 0xf8870000
> ext3 118024 1 - Live 0xf88d0000
> jbd 49960 1 ext3, Live 0xf889f000
> piix 8836 0 [permanent], Live 0xf882c000
> ide_disk 16000 0 - Live 0xf8827000
> ide_cd 36000 0 - Live 0xf885d000
> cdrom 32800 2 sr_mod,ide_cd, Live 0xf8853000
> ide_scsi 16392 0 - Live 0xf8821000
> scsi_mod 132360 5 sg,sr_mod,sd_mod,libata,ide_scsi, Live 0xf887d000
> ide_core 106704 5 generic,piix,ide_disk,ide_cd,ide_scsi, Live 0xf8837000
>
> ------------------------------------------------------------------------------------------------------------------------------------------------
> /proc/ioports
> 0000-001f : dma1
> 0020-0021 : pic1
> 0040-0043 : timer0
> 0050-0053 : timer1
> 0060-006f : keyboard
> 0070-0077 : rtc
> 0080-008f : dma page reg
> 00a0-00a1 : pic2
> 00c0-00df : dma2
> 00f0-00ff : fpu
> 0170-0177 : 0000:00:1f.2
> 0170-0177 : libata
> 01f0-01f7 : 0000:00:1f.2
> 01f0-01f7 : libata
> 02f8-02ff : serial
> 0376-0376 : 0000:00:1f.2
> 0376-0376 : libata
> 0378-037a : parport0
> 03c0-03df : vga+
> 03f2-03f5 : floppy
> 03f6-03f6 : 0000:00:1f.2
> 03f6-03f6 : libata
> 03f7-03f7 : floppy DIR
> 03f8-03ff : serial
> 0cf8-0cff : PCI conf1
> 1000-107f : 0000:00:1f.0
> 1000-1003 : ACPI PM1a_EVT_BLK
> 1004-1005 : ACPI PM1a_CNT_BLK
> 1008-100b : ACPI PM_TMR
> 1028-102f : ACPI GPE0_BLK
> 1080-10bf : 0000:00:1f.0
> 1400-141f : 0000:00:1f.3
> a000-afff : PCI Bus #02
> a000-a0ff : 0000:02:01.0
> a000-a0ff : 8139too
> b000-b01f : 0000:00:1d.1
> b000-b01f : uhci_hcd
> b400-b41f : 0000:00:1d.2
> b400-b41f : uhci_hcd
> b800-b81f : 0000:00:1d.3
> b800-b81f : uhci_hcd
> bc00-bc1f : 0000:00:1d.0
> bc00-bc1f : uhci_hcd
> d800-d8ff : 0000:00:1f.5
> d800-d8ff : Intel ICH5
> dc00-dc3f : 0000:00:1f.5
> dc00-dc3f : Intel ICH5
> f000-f00f : 0000:00:1f.2
> f000-f00f : libata
> -----------------------------------------------------------------------------------------------------------------------------------------------
> /proc/iomem
>
> 00000000-0009f7ff : System RAM
> 0009f800-0009ffff : reserved
> 000a0000-000bffff : Video RAM area
> 000c0000-000c7fff : Video ROM
> 000d0000-000d7fff : pnp 00:00
> 000f0000-000fffff : System ROM
> 00100000-3ffeffff : System RAM
> 00100000-00287ed7 : Kernel code
> 00287ed8-003224df : Kernel data
> 3fff0000-3fff2fff : ACPI Non-volatile Storage
> 3fff3000-3fffffff : ACPI Tables
> d0000000-dfffffff : PCI Bus #01
> d0000000-dfffffff : 0000:01:00.0
> e0000000-e7ffffff : 0000:00:00.0
> e8000000-ebffffff : PCI Bus #02
> e8000000-ebffffff : 0000:02:04.0
> ec000000-eeffffff : PCI Bus #01
> ec000000-ecffffff : 0000:01:00.0
> ec000000-ecffffff : nvidia
> ed000000-edffffff : 0000:01:00.0
> ee000000-ee01ffff : 0000:01:00.0
> ef000000-ef0fffff : PCI Bus #02
> ef000000-ef0000ff : 0000:02:01.0
> ef000000-ef0000ff : 8139too
> ef100000-ef1003ff : 0000:00:1d.7
> ef100000-ef1003ff : ehci_hcd
> ef101000-ef1011ff : 0000:00:1f.5
> ef101000-ef1011ff : Intel ICH5
> ef102000-ef1020ff : 0000:00:1f.5
> ef102000-ef1020ff : Intel ICH5
> fec00000-ffffffff : reserved
> ~
> ----------------------------------------------------------------------------------------------------------------------------------------------
> lspci -vvv
>
> 00:00.0 Host bridge: Intel Corporation 82865G/PE/P DRAM
> Controller/Host-Hub Interface (rev 02)
> Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE)
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort+ >SERR- <PERR-
> Latency: 0
> Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
> Capabilities: [e4] Vendor Specific Information
> Capabilities: [a0] AGP version 3.0
> Status: RQ=32 Iso- ArqSz=2 Cal=2 SBA+ ITACoh- GART64-
> HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
> Command: RQ=1 ArqSz=0 Cal=2 SBA+ AGP+ GART64- 64bit- FW-
> Rate=x8
>
> 00:01.0 PCI bridge: Intel Corporation 82865G/PE/P PCI to AGP Controller
> (rev 02) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: ec000000-eeffffff
> Prefetchable memory behind bridge: d0000000-dfffffff
> Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
>
> 00:1d.0 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
> UHCI Controller #1 (rev 02) (prog-if 00 [UHCI])
> Subsystem: Giga-byte Technology GA-8IPE1000/8KNXP motherboard
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin A routed to IRQ 16
> Region 4: I/O ports at bc00 [size=32]
>
> 00:1d.1 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
> UHCI Controller #2 (rev 02) (prog-if 00 [UHCI])
> Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE)
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin B routed to IRQ 17
> Region 4: I/O ports at b000 [size=32]
>
> 00:1d.2 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
> UHCI Controller #3 (rev 02) (prog-if 00 [UHCI])
> Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE)
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin C routed to IRQ 18
> Region 4: I/O ports at b400 [size=32]
>
> 00:1d.3 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
> UHCI Controller #4 (rev 02) (prog-if 00 [UHCI])
> Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE)
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin A routed to IRQ 16
> Region 4: I/O ports at b800 [size=32]
> 00:1d.7 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2
> EHCI Controller (rev 02) (prog-if 20 [EHCI])
> Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE)
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin D routed to IRQ 19
> Region 0: Memory at ef100000 (32-bit, non-prefetchable) [size=1K]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev c2) (prog-if
> 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
> I/O behind bridge: 0000a000-0000afff
> Memory behind bridge: ef000000-ef0fffff
> Prefetchable memory behind bridge: e8000000-ebffffff
> Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
>
> 00:1f.0 ISA bridge: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC
> Interface Bridge (rev 02)
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
>
> 00:1f.2 IDE interface: Intel Corporation 82801EB (ICH5) SATA Controller
> (rev 02) (prog-if 8a [Master SecP PriP])
> Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE)
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin A routed to IRQ 18
> Region 0: I/O ports at 01f0 [size=8]
> Region 1: I/O ports at 03f4 [size=1]
> Region 2: I/O ports at 0170 [size=8]
> Region 3: I/O ports at 0374 [size=1]
> Region 4: I/O ports at f000 [size=16]
>
> 00:1f.3 SMBus: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus
> Controller (rev 02)
> Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE)
> Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Interrupt: pin B routed to IRQ 9
> Region 4: I/O ports at 1400 [size=32]
>
> 00:1f.5 Multimedia audio controller: Intel Corporation 82801EB/ER
> (ICH5/ICH5R) AC'97 Audio Controller (rev 02)
> Subsystem: Giga-byte Technology GA-8IPE1000/8KNXP motherboard
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin B routed to IRQ 21
> Region 0: I/O ports at d800 [size=256]
> Region 1: I/O ports at dc00 [size=64]
> Region 2: Memory at ef101000 (32-bit, non-prefetchable) [size=512]
> Region 3: Memory at ef102000 (32-bit, non-prefetchable) [size=256]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> 01:00.0 VGA compatible controller: nVidia Corporation NV43 [GeForce
> 6600/GeForce 6600 GT] (rev a2) (prog-if 00 [VGA])
> Subsystem: XFX Pine Group Inc. GeForce 6600 GT AGP 128MB DDR3
> DUAL DVI TV
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 248 (1250ns min, 250ns max)
> Interrupt: pin A routed to IRQ 16
> Region 0: Memory at ec000000 (32-bit, non-prefetchable) [size=16M]
> Region 1: Memory at d0000000 (32-bit, prefetchable) [size=256M]
> Region 2: Memory at ed000000 (32-bit, non-prefetchable) [size=16M]
> [virtual] Expansion ROM at ee000000 [disabled] [size=128K]
> Capabilities: [60] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [44] AGP version 3.0
> Status: RQ=256 Iso- ArqSz=0 Cal=3 SBA+ ITACoh- GART64-
> HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
> Command: RQ=32 ArqSz=2 Cal=0 SBA+ AGP+ GART64- 64bit-
> FW- Rate=x8
>
> 02:01.0 Ethernet controller: D-Link System Inc RTL8139 Ethernet (rev 10)
> Subsystem: D-Link System Inc DFE-530TX+ 10/100 Ethernet Adapter
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64 (8000ns min, 16000ns max)
> Interrupt: pin A routed to IRQ 20
> Region 0: I/O ports at a000 [size=256]
> Region 1: Memory at ef000000 (32-bit, non-prefetchable) [size=256]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
> PME(D0-,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 02:04.0 Multimedia video controller: Internext Compression Inc iTVC16
> (CX23416) MPEG-2 Encoder (rev 01)
> Subsystem: Hauppauge computer works Inc. WinTV PVR 150
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (32000ns min, 2000ns max), Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at e8000000 (32-bit, prefetchable) [size=64M]
> Capabilities: [44] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> --------------------------------------------------------------------------------------------------------------------------------------------
> /proc/scsi/scsi
>
> Attached devices:
> Host: scsi0 Channel: 00 Id: 00 Lun: 00
> Vendor: ATA Model: HDS722516VLSA80 Rev: V34O
> Type: Direct-Access ANSI SCSI revision: 05
> Host: scsi1 Channel: 00 Id: 00 Lun: 00
> Vendor: SONY Model: CD-ROM CDU5211 Rev: YYS7
> Type: CD-ROM ANSI SCSI revision: 05
>
>
>
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: PROBLEM: kernel panic
2007-10-14 20:24 ` Trond Myklebust
@ 2007-10-14 20:44 ` Scott Petler
2007-10-14 20:51 ` Doug Whitesell (LKML)
0 siblings, 1 reply; 9+ messages in thread
From: Scott Petler @ 2007-10-14 20:44 UTC (permalink / raw)
To: Trond Myklebust; +Cc: linux-kernel
Trond,
I'm not exactly sure how to go back to not using the nvidia driver and
select the xorg one. I do know that I wasn't able to use both monitors
with the xorg driver, but I'm willing to try that to isolate the problem.
Scott
Output from /proc/mounts:
rootfs / rootfs rw 0 0
none /sys sysfs rw 0 0
none /proc proc rw 0 0
udev /dev tmpfs rw 0 0
/dev/sda2 / ext3 rw,data=ordered 0 0
/dev/sda2 /dev/.static/dev ext3 rw,data=ordered 0 0
tmpfs /lib/init/rw tmpfs rw,nosuid 0 0
usbfs /proc/bus/usb usbfs rw,nosuid,nodev,noexec 0 0
tmpfs /dev/shm tmpfs rw,nosuid,nodev 0 0
devpts /dev/pts devpts rw,nosuid,noexec 0 0
twin:/home /home nfs
rw,vers=3,rsize=32768,wsize=32768,hard,intr,proto=tcp,timeo=600,retrans=2,sec=sys,addr=twin
0 0
twin:/mp3 /mp3 nfs
rw,vers=3,rsize=32768,wsize=32768,hard,intr,proto=tcp,timeo=600,retrans=2,sec=sys,addr=twin
0 0
Trond Myklebust wrote:
> On Sat, 2007-10-13 at 15:48 -0700, Scott Petler wrote:
>
>> Machine lockup with caps lock/num lock flashing or complete reboot/panic.
>>
>> I get various lockup issues with this kernel, (2.6.23 also similar
>> problem). I had problems getting e1000 lan module to work (it was fine
>> in 2.6.21.5). I disabled it and installed a different lan card that
>> seems to work "better".
>>
>> Dual head machine 1GB RAM, nvidia driver x86-100.14.19
>>
>
> Are you able to repeat this Oops _without_ the nvidia driver?
>
> Also, please provide the output from /proc/mounts
>
> Cheers
> Trond
>
>
>
>> Here is output of ver_linux:
>> ---------------------------------------------------------------------------------------------------------------------------------------------
>>
>> Linux zion 2.6.23-rc9 #3 Fri Oct 12 18:27:56 PDT 2007 i686 GNU/Linux
>>
>> Gnu C 4.1.2
>> Gnu make 3.81
>> binutils 2.17
>> util-linux 2.12r
>> mount 2.12r
>> module-init-tools 3.3-pre2
>> e2fsprogs 1.40-WIP
>> Linux C Library 3.6
>> Dynamic linker (ldd) 2.3.6
>> Procps 3.2.7
>> Net-tools 1.60
>> Console-tools 0.2.3
>> Sh-utils 5.97
>> udev 105
>> Modules Loaded nfs lockd sunrpc nvidia i2c_core af_packet ipv6
>> capability commoncap ppdev lp ac battery dm_mod e1000 loop snd_intel8x0
>> snd_ac97_codec ac97_bus snd_pcm_oss snd_mixer_oss snd_pcm snd_timer
>> parport_pc button parport snd 8250_pnp 8250 serial_core soundcore shpchp
>> pci_hotplug snd_page_alloc rng_core floppy intel_agp agpgart rtc sg
>> evdev sr_mod usbhid sd_mod ata_piix 8139too ata_generic ehci_hcd
>> uhci_hcd mii bitrev crc32 libata generic usbcore thermal processor fan
>> unix ext3 jbd piix ide_disk ide_cd cdrom ide_scsi scsi_mod ide_core
>> ---------------------------------------------------------------------------------------------------------------------------------------------
>>
>> Here is output from syslog as it went down:
>>
>> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
>> zion kernel: Oops: 0002 [#1]
>>
>> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
>> zion kernel: CPU: 0
>>
>> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
>> zion kernel: EIP: 0060:[<e1168fde>] Tainted: P VLI
>>
>> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
>> zion kernel: EFLAGS: 00010206 (2.6.23-rc9 #3)
>>
>> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
>> zion kernel: EIP is at 0xe1168fde
>>
>> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
>> zion kernel: esi: f8f34700 edi: 00000000 ebp: 00000001 esp: e7cf3e00
>>
>> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
>> zion kernel: ds: 007b es: 007b fs: 0000 gs: 0033 ss: 0068
>>
>> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
>> zion kernel: Process firefox-bin (pid: 8397, ti=e7cf2000 task=f258ca90
>> task.ti=e
>> 7cf2000)
>>
>> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
>> zion kernel: Stack: f8f18eb7 c01367f6 e7cf3e48 000003e8 000003e8
>> ed3e97c0 f1f6db
>> 9c f1f6db9c
>>
>> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
>> zion kernel: e7cf3f54 f8f60ec2 0004257b 00000000 00000000
>> f1f037dc e7cf3f
>> 54 c01563d0
>>
>> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
>> zion kernel: 019cc780 e7cf3eb0 c0155a63 dfff38c0 c014e001
>> 019cc780 f1f037
>> dc dfe0ecf4
>>
>> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
>> zion kernel: Call Trace:
>>
>> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
>> zion kernel: [<f8f18eb7>] rpcauth_lookupcred+0x63/0x87 [sunrpc]
>>
>> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
>> zion kernel: [<c01367f6>] pagevec_lookup+0x1c/0x22
>>
>> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
>> zion kernel: [<f8f60ec2>] nfs_permission+0xab/0x183 [nfs]
>>
>> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
>> zion kernel: [<c01563d0>] __d_lookup+0x8b/0xbf
>>
>> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
>> zion kernel: [<c0155a63>] dput+0x15/0xcb
>>
>> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
>> zion kernel: [<f8f60e17>] nfs_permission+0x0/0x183 [nfs]
>> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
>> zion kernel: [<c014f648>] __link_path_walk+0x11c/0xa79
>>
>> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
>> zion kernel: [<c0102ff8>] setup_sigcontext+0x104/0x187
>>
>> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
>> zion kernel: [<c014ffe7>] link_path_walk+0x42/0xaf
>> Read from remote host 192.168.1.175: Connection reset by peer
>> Connection to 192.168.1.175 closed.
>>
>> Message from syslogd@zion at Sat Oct 13 15:22:34 2007 ...
>> zion kernel: [<c014de5a>] permission+0x9e/0xdb
>>
>> ------------------------------------------------------------------------------------------------------------------------------------------------
>> /proc/cpuinfo
>>
>> processor : 0
>> vendor_id : GenuineIntel
>> cpu family : 15
>> model : 2
>> model name : Intel(R) Pentium(R) 4 CPU 2.40GHz
>> stepping : 7
>> cpu MHz : 2411.749
>> cache size : 512 KB
>> fdiv_bug : no
>> hlt_bug : no
>> f00f_bug : no
>> coma_bug : no
>> fpu : yes
>> fpu_exception : yes
>> cpuid level : 2
>> wp : yes
>> flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
>> mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe pebs
>> bts sync_rdtsc cid xtpr
>> bogomips : 4826.95
>> clflush size : 64
>>
>> ----------------------------------------------------------------------------------------------------------------------------------------------------
>> /proc/modules
>>
>> nfs 120816 1 - Live 0xf8f3a000
>> lockd 59656 2 nfs, Live 0xf8d7a000
>> sunrpc 154524 6 nfs,lockd, Live 0xf8f13000
>> nvidia 6212112 24 - Live 0xf9448000 (P)
>> i2c_core 23312 1 nvidia, Live 0xf8d4a000
>> af_packet 20104 2 - Live 0xf8d51000
>> ipv6 222052 10 - Live 0xf8d8b000
>> capability 5000 0 - Live 0xf8d39000
>> commoncap 7296 1 capability, Live 0xf886a000
>> ppdev 8964 0 - Live 0xf8d35000
>> lp 11204 0 - Live 0xf8d31000
>> ac 5764 0 - Live 0xf89fa000
>> battery 12424 0 - Live 0xf89ff000
>> dm_mod 49728 0 - Live 0xf8d3c000
>> e1000 111424 0 - Live 0xf8a2c000
>> loop 16772 0 - Live 0xf89ee000
>> snd_intel8x0 31260 0 - Live 0xf8a05000
>> snd_ac97_codec 90784 1 snd_intel8x0, Live 0xf8a4a000
>> ac97_bus 2432 1 snd_ac97_codec, Live 0xf88ce000
>> snd_pcm_oss 38560 0 - Live 0xf8a21000
>> snd_mixer_oss 15360 1 snd_pcm_oss, Live 0xf89a5000
>> snd_pcm 68872 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss, Live 0xf8a0f000
>> snd_timer 19972 1 snd_pcm, Live 0xf89f4000
>> parport_pc 33572 1 - Live 0xf89ca000
>> button 8464 0 - Live 0xf89c6000
>> parport 33096 3 ppdev,lp,parport_pc, Live 0xf89e2000
>> snd 46820 6
>> snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer,
>> Live 0xf89d5000
>> 8250_pnp 9728 0 - Live 0xf89aa000
>> 8250 21748 1 8250_pnp, Live 0xf89bf000
>> serial_core 19072 1 8250, Live 0xf89b9000
>> soundcore 7392 1 snd, Live 0xf895d000
>> shpchp 30996 0 - Live 0xf89b0000
>> pci_hotplug 13960 1 shpchp, Live 0xf8963000
>> snd_page_alloc 10248 2 snd_intel8x0,snd_pcm, Live 0xf89a1000
>> rng_core 5252 0 - Live 0xf8960000
>> floppy 51876 0 - Live 0xf8971000
>> intel_agp 23572 1 - Live 0xf894d000
>> agpgart 31152 2 nvidia,intel_agp, Live 0xf8968000
>> rtc 11800 0 - Live 0xf8949000
>> sg 31644 0 - Live 0xf8954000
>> evdev 9600 1 - Live 0xf890b000
>> sr_mod 15140 0 - Live 0xf8906000
>> usbhid 26496 0 - Live 0xf8941000
>> sd_mod 26000 3 - Live 0xf8939000
>> ata_piix 17028 2 - Live 0xf8933000
>> 8139too 23552 0 - Live 0xf892c000
>> ata_generic 7812 0 - Live 0xf881b000
>> ehci_hcd 27916 0 - Live 0xf88f1000
>> uhci_hcd 21900 0 - Live 0xf88f9000
>> mii 5504 1 8139too, Live 0xf88ee000
>> bitrev 2176 1 8139too, Live 0xf88cc000
>> crc32 4224 1 8139too, Live 0xf886d000
>> libata 111796 2 ata_piix,ata_generic, Live 0xf890f000
>> generic 4996 0 [permanent], Live 0xf8867000
>> usbcore 122264 4 usbhid,ehci_hcd,uhci_hcd, Live 0xf88ad000
>> thermal 15644 0 - Live 0xf8878000
>> processor 21152 1 thermal, Live 0xf8830000
>> fan 5252 0 - Live 0xf881e000
>> unix 24880 654 - Live 0xf8870000
>> ext3 118024 1 - Live 0xf88d0000
>> jbd 49960 1 ext3, Live 0xf889f000
>> piix 8836 0 [permanent], Live 0xf882c000
>> ide_disk 16000 0 - Live 0xf8827000
>> ide_cd 36000 0 - Live 0xf885d000
>> cdrom 32800 2 sr_mod,ide_cd, Live 0xf8853000
>> ide_scsi 16392 0 - Live 0xf8821000
>> scsi_mod 132360 5 sg,sr_mod,sd_mod,libata,ide_scsi, Live 0xf887d000
>> ide_core 106704 5 generic,piix,ide_disk,ide_cd,ide_scsi, Live 0xf8837000
>>
>> ------------------------------------------------------------------------------------------------------------------------------------------------
>> /proc/ioports
>> 0000-001f : dma1
>> 0020-0021 : pic1
>> 0040-0043 : timer0
>> 0050-0053 : timer1
>> 0060-006f : keyboard
>> 0070-0077 : rtc
>> 0080-008f : dma page reg
>> 00a0-00a1 : pic2
>> 00c0-00df : dma2
>> 00f0-00ff : fpu
>> 0170-0177 : 0000:00:1f.2
>> 0170-0177 : libata
>> 01f0-01f7 : 0000:00:1f.2
>> 01f0-01f7 : libata
>> 02f8-02ff : serial
>> 0376-0376 : 0000:00:1f.2
>> 0376-0376 : libata
>> 0378-037a : parport0
>> 03c0-03df : vga+
>> 03f2-03f5 : floppy
>> 03f6-03f6 : 0000:00:1f.2
>> 03f6-03f6 : libata
>> 03f7-03f7 : floppy DIR
>> 03f8-03ff : serial
>> 0cf8-0cff : PCI conf1
>> 1000-107f : 0000:00:1f.0
>> 1000-1003 : ACPI PM1a_EVT_BLK
>> 1004-1005 : ACPI PM1a_CNT_BLK
>> 1008-100b : ACPI PM_TMR
>> 1028-102f : ACPI GPE0_BLK
>> 1080-10bf : 0000:00:1f.0
>> 1400-141f : 0000:00:1f.3
>> a000-afff : PCI Bus #02
>> a000-a0ff : 0000:02:01.0
>> a000-a0ff : 8139too
>> b000-b01f : 0000:00:1d.1
>> b000-b01f : uhci_hcd
>> b400-b41f : 0000:00:1d.2
>> b400-b41f : uhci_hcd
>> b800-b81f : 0000:00:1d.3
>> b800-b81f : uhci_hcd
>> bc00-bc1f : 0000:00:1d.0
>> bc00-bc1f : uhci_hcd
>> d800-d8ff : 0000:00:1f.5
>> d800-d8ff : Intel ICH5
>> dc00-dc3f : 0000:00:1f.5
>> dc00-dc3f : Intel ICH5
>> f000-f00f : 0000:00:1f.2
>> f000-f00f : libata
>> -----------------------------------------------------------------------------------------------------------------------------------------------
>> /proc/iomem
>>
>> 00000000-0009f7ff : System RAM
>> 0009f800-0009ffff : reserved
>> 000a0000-000bffff : Video RAM area
>> 000c0000-000c7fff : Video ROM
>> 000d0000-000d7fff : pnp 00:00
>> 000f0000-000fffff : System ROM
>> 00100000-3ffeffff : System RAM
>> 00100000-00287ed7 : Kernel code
>> 00287ed8-003224df : Kernel data
>> 3fff0000-3fff2fff : ACPI Non-volatile Storage
>> 3fff3000-3fffffff : ACPI Tables
>> d0000000-dfffffff : PCI Bus #01
>> d0000000-dfffffff : 0000:01:00.0
>> e0000000-e7ffffff : 0000:00:00.0
>> e8000000-ebffffff : PCI Bus #02
>> e8000000-ebffffff : 0000:02:04.0
>> ec000000-eeffffff : PCI Bus #01
>> ec000000-ecffffff : 0000:01:00.0
>> ec000000-ecffffff : nvidia
>> ed000000-edffffff : 0000:01:00.0
>> ee000000-ee01ffff : 0000:01:00.0
>> ef000000-ef0fffff : PCI Bus #02
>> ef000000-ef0000ff : 0000:02:01.0
>> ef000000-ef0000ff : 8139too
>> ef100000-ef1003ff : 0000:00:1d.7
>> ef100000-ef1003ff : ehci_hcd
>> ef101000-ef1011ff : 0000:00:1f.5
>> ef101000-ef1011ff : Intel ICH5
>> ef102000-ef1020ff : 0000:00:1f.5
>> ef102000-ef1020ff : Intel ICH5
>> fec00000-ffffffff : reserved
>> ~
>> ----------------------------------------------------------------------------------------------------------------------------------------------
>> lspci -vvv
>>
>> 00:00.0 Host bridge: Intel Corporation 82865G/PE/P DRAM
>> Controller/Host-Hub Interface (rev 02)
>> Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE)
>> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
>> ParErr- Stepping- SERR+ FastB2B-
>> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
>> <TAbort- <MAbort+ >SERR- <PERR-
>> Latency: 0
>> Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
>> Capabilities: [e4] Vendor Specific Information
>> Capabilities: [a0] AGP version 3.0
>> Status: RQ=32 Iso- ArqSz=2 Cal=2 SBA+ ITACoh- GART64-
>> HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
>> Command: RQ=1 ArqSz=0 Cal=2 SBA+ AGP+ GART64- 64bit- FW-
>> Rate=x8
>>
>> 00:01.0 PCI bridge: Intel Corporation 82865G/PE/P PCI to AGP Controller
>> (rev 02) (prog-if 00 [Normal decode])
>> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
>> ParErr- Stepping- SERR- FastB2B-
>> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
>> <TAbort- <MAbort- >SERR- <PERR-
>> Latency: 64
>> Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
>> I/O behind bridge: 0000f000-00000fff
>> Memory behind bridge: ec000000-eeffffff
>> Prefetchable memory behind bridge: d0000000-dfffffff
>> Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
>> <TAbort- <MAbort+ <SERR- <PERR-
>> BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
>>
>> 00:1d.0 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
>> UHCI Controller #1 (rev 02) (prog-if 00 [UHCI])
>> Subsystem: Giga-byte Technology GA-8IPE1000/8KNXP motherboard
>> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
>> ParErr- Stepping- SERR- FastB2B-
>> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
>> <TAbort- <MAbort- >SERR- <PERR-
>> Latency: 0
>> Interrupt: pin A routed to IRQ 16
>> Region 4: I/O ports at bc00 [size=32]
>>
>> 00:1d.1 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
>> UHCI Controller #2 (rev 02) (prog-if 00 [UHCI])
>> Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE)
>> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
>> ParErr- Stepping- SERR- FastB2B-
>> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
>> <TAbort- <MAbort- >SERR- <PERR-
>> Latency: 0
>> Interrupt: pin B routed to IRQ 17
>> Region 4: I/O ports at b000 [size=32]
>>
>> 00:1d.2 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
>> UHCI Controller #3 (rev 02) (prog-if 00 [UHCI])
>> Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE)
>> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
>> ParErr- Stepping- SERR- FastB2B-
>> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
>> <TAbort- <MAbort- >SERR- <PERR-
>> Latency: 0
>> Interrupt: pin C routed to IRQ 18
>> Region 4: I/O ports at b400 [size=32]
>>
>> 00:1d.3 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
>> UHCI Controller #4 (rev 02) (prog-if 00 [UHCI])
>> Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE)
>> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
>> ParErr- Stepping- SERR- FastB2B-
>> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
>> <TAbort- <MAbort- >SERR- <PERR-
>> Latency: 0
>> Interrupt: pin A routed to IRQ 16
>> Region 4: I/O ports at b800 [size=32]
>> 00:1d.7 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2
>> EHCI Controller (rev 02) (prog-if 20 [EHCI])
>> Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE)
>> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
>> ParErr- Stepping- SERR- FastB2B-
>> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
>> <TAbort- <MAbort- >SERR- <PERR-
>> Latency: 0
>> Interrupt: pin D routed to IRQ 19
>> Region 0: Memory at ef100000 (32-bit, non-prefetchable) [size=1K]
>> Capabilities: [50] Power Management version 2
>> Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
>> PME(D0+,D1-,D2-,D3hot+,D3cold+)
>> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>>
>> 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev c2) (prog-if
>> 00 [Normal decode])
>> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
>> ParErr- Stepping- SERR- FastB2B-
>> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
>> <TAbort- <MAbort- >SERR- <PERR-
>> Latency: 0
>> Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
>> I/O behind bridge: 0000a000-0000afff
>> Memory behind bridge: ef000000-ef0fffff
>> Prefetchable memory behind bridge: e8000000-ebffffff
>> Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
>> <TAbort- <MAbort- <SERR- <PERR-
>> BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
>>
>> 00:1f.0 ISA bridge: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC
>> Interface Bridge (rev 02)
>> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
>> ParErr- Stepping- SERR- FastB2B-
>> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
>> <TAbort- <MAbort- >SERR- <PERR-
>> Latency: 0
>>
>> 00:1f.2 IDE interface: Intel Corporation 82801EB (ICH5) SATA Controller
>> (rev 02) (prog-if 8a [Master SecP PriP])
>> Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE)
>> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
>> ParErr- Stepping- SERR- FastB2B-
>> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
>> <TAbort- <MAbort- >SERR- <PERR-
>> Latency: 0
>> Interrupt: pin A routed to IRQ 18
>> Region 0: I/O ports at 01f0 [size=8]
>> Region 1: I/O ports at 03f4 [size=1]
>> Region 2: I/O ports at 0170 [size=8]
>> Region 3: I/O ports at 0374 [size=1]
>> Region 4: I/O ports at f000 [size=16]
>>
>> 00:1f.3 SMBus: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus
>> Controller (rev 02)
>> Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE)
>> Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
>> ParErr- Stepping- SERR- FastB2B-
>> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
>> <TAbort- <MAbort- >SERR- <PERR-
>> Interrupt: pin B routed to IRQ 9
>> Region 4: I/O ports at 1400 [size=32]
>>
>> 00:1f.5 Multimedia audio controller: Intel Corporation 82801EB/ER
>> (ICH5/ICH5R) AC'97 Audio Controller (rev 02)
>> Subsystem: Giga-byte Technology GA-8IPE1000/8KNXP motherboard
>> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
>> ParErr- Stepping- SERR- FastB2B-
>> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
>> <TAbort- <MAbort- >SERR- <PERR-
>> Latency: 0
>> Interrupt: pin B routed to IRQ 21
>> Region 0: I/O ports at d800 [size=256]
>> Region 1: I/O ports at dc00 [size=64]
>> Region 2: Memory at ef101000 (32-bit, non-prefetchable) [size=512]
>> Region 3: Memory at ef102000 (32-bit, non-prefetchable) [size=256]
>> Capabilities: [50] Power Management version 2
>> Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
>> PME(D0+,D1-,D2-,D3hot+,D3cold+)
>> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>> 01:00.0 VGA compatible controller: nVidia Corporation NV43 [GeForce
>> 6600/GeForce 6600 GT] (rev a2) (prog-if 00 [VGA])
>> Subsystem: XFX Pine Group Inc. GeForce 6600 GT AGP 128MB DDR3
>> DUAL DVI TV
>> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
>> ParErr- Stepping- SERR- FastB2B-
>> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
>> <TAbort- <MAbort- >SERR- <PERR-
>> Latency: 248 (1250ns min, 250ns max)
>> Interrupt: pin A routed to IRQ 16
>> Region 0: Memory at ec000000 (32-bit, non-prefetchable) [size=16M]
>> Region 1: Memory at d0000000 (32-bit, prefetchable) [size=256M]
>> Region 2: Memory at ed000000 (32-bit, non-prefetchable) [size=16M]
>> [virtual] Expansion ROM at ee000000 [disabled] [size=128K]
>> Capabilities: [60] Power Management version 2
>> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
>> PME(D0-,D1-,D2-,D3hot-,D3cold-)
>> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>> Capabilities: [44] AGP version 3.0
>> Status: RQ=256 Iso- ArqSz=0 Cal=3 SBA+ ITACoh- GART64-
>> HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
>> Command: RQ=32 ArqSz=2 Cal=0 SBA+ AGP+ GART64- 64bit-
>> FW- Rate=x8
>>
>> 02:01.0 Ethernet controller: D-Link System Inc RTL8139 Ethernet (rev 10)
>> Subsystem: D-Link System Inc DFE-530TX+ 10/100 Ethernet Adapter
>> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
>> ParErr- Stepping- SERR- FastB2B-
>> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
>> <TAbort- <MAbort- >SERR- <PERR-
>> Latency: 64 (8000ns min, 16000ns max)
>> Interrupt: pin A routed to IRQ 20
>> Region 0: I/O ports at a000 [size=256]
>> Region 1: Memory at ef000000 (32-bit, non-prefetchable) [size=256]
>> Capabilities: [50] Power Management version 2
>> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
>> PME(D0-,D1+,D2+,D3hot+,D3cold+)
>> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>>
>> 02:04.0 Multimedia video controller: Internext Compression Inc iTVC16
>> (CX23416) MPEG-2 Encoder (rev 01)
>> Subsystem: Hauppauge computer works Inc. WinTV PVR 150
>> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
>> ParErr- Stepping- SERR- FastB2B-
>> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
>> <TAbort- <MAbort- >SERR- <PERR-
>> Latency: 32 (32000ns min, 2000ns max), Cache Line Size: 32 bytes
>> Interrupt: pin A routed to IRQ 11
>> Region 0: Memory at e8000000 (32-bit, prefetchable) [size=64M]
>> Capabilities: [44] Power Management version 2
>> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
>> PME(D0-,D1-,D2-,D3hot-,D3cold-)
>> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>>
>> --------------------------------------------------------------------------------------------------------------------------------------------
>> /proc/scsi/scsi
>>
>> Attached devices:
>> Host: scsi0 Channel: 00 Id: 00 Lun: 00
>> Vendor: ATA Model: HDS722516VLSA80 Rev: V34O
>> Type: Direct-Access ANSI SCSI revision: 05
>> Host: scsi1 Channel: 00 Id: 00 Lun: 00
>> Vendor: SONY Model: CD-ROM CDU5211 Rev: YYS7
>> Type: CD-ROM ANSI SCSI revision: 05
>>
>>
>>
>>
>> -
>> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
>> the body of a message to majordomo@vger.kernel.org
>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>> Please read the FAQ at http://www.tux.org/lkml/
>>
>
>
>
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: PROBLEM: kernel panic
2007-10-14 20:44 ` Scott Petler
@ 2007-10-14 20:51 ` Doug Whitesell (LKML)
2007-10-14 21:00 ` Scott Petler
0 siblings, 1 reply; 9+ messages in thread
From: Doug Whitesell (LKML) @ 2007-10-14 20:51 UTC (permalink / raw)
To: Scott Petler; +Cc: linux-kernel
On Oct 14, 2007, at 1:44 PM, Scott Petler wrote:
> Trond,
>
> I'm not exactly sure how to go back to not using the nvidia driver
> and select the xorg one. I do know that I wasn't able to use both
> monitors with the xorg driver, but I'm willing to try that to
> isolate the problem.
If memory serves, you change your xorg.conf's "Device" section's
"Driver" entry to read:
"nv"
instead of
"nvidia",
although I would consult the xorg documentation/your distribution's
documentation (and back up your working xorg.conf) for specific
details. (Your boot sequence may also automatically load the nvidia
module, again, consult your distribution's documentation for details.)
Cheers/hope this helps,
dcw
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: PROBLEM: kernel panic
2007-10-14 20:51 ` Doug Whitesell (LKML)
@ 2007-10-14 21:00 ` Scott Petler
2007-10-14 21:32 ` Trond Myklebust
0 siblings, 1 reply; 9+ messages in thread
From: Scott Petler @ 2007-10-14 21:00 UTC (permalink / raw)
To: Doug Whitesell (LKML); +Cc: linux-kernel
Doug,
I thought that might do it, it does seem to work. I edited the driver
line in my xorg.conf
from nvidia to nv and then,
<alt><ctrl> F1
login as root
/etc/init.d/gdm stop
/etc/init.d/gdm start
It came back up with the same flashing crap on the second monitor, so I
did it again with
the 2nd monitor turned off altogether, and I'll see how long it will run
on the single monitor
without the nvidia driver without crashing (maybe forever...).
Thanks,
Scott
Doug Whitesell (LKML) wrote:
> On Oct 14, 2007, at 1:44 PM, Scott Petler wrote:
>
>> Trond,
>>
>> I'm not exactly sure how to go back to not using the nvidia driver
>> and select the xorg one. I do know that I wasn't able to use both
>> monitors with the xorg driver, but I'm willing to try that to isolate
>> the problem.
>
> If memory serves, you change your xorg.conf's "Device" section's
> "Driver" entry to read:
> "nv"
> instead of
> "nvidia",
>
> although I would consult the xorg documentation/your distribution's
> documentation (and back up your working xorg.conf) for specific
> details. (Your boot sequence may also automatically load the nvidia
> module, again, consult your distribution's documentation for details.)
>
> Cheers/hope this helps,
> dcw
>
>
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: PROBLEM: kernel panic
2007-10-14 21:00 ` Scott Petler
@ 2007-10-14 21:32 ` Trond Myklebust
2007-10-14 21:36 ` Scott Petler
0 siblings, 1 reply; 9+ messages in thread
From: Trond Myklebust @ 2007-10-14 21:32 UTC (permalink / raw)
To: Scott Petler; +Cc: Doug Whitesell (LKML), linux-kernel
On Sun, 2007-10-14 at 14:00 -0700, Scott Petler wrote:
> Doug,
>
> I thought that might do it, it does seem to work. I edited the driver
> line in my xorg.conf
> from nvidia to nv and then,
> <alt><ctrl> F1
> login as root
> /etc/init.d/gdm stop
> /etc/init.d/gdm start
>
> It came back up with the same flashing crap on the second monitor, so I
> did it again with
> the 2nd monitor turned off altogether, and I'll see how long it will run
> on the single monitor
> without the nvidia driver without crashing (maybe forever...).
>
> Thanks,
> Scott
Please don't forget to reboot, though. The kernel will remain tainted
until you've rebooted without loading the nvidia module.
Cheers
Trond
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: PROBLEM: kernel panic
2007-10-14 21:32 ` Trond Myklebust
@ 2007-10-14 21:36 ` Scott Petler
0 siblings, 0 replies; 9+ messages in thread
From: Scott Petler @ 2007-10-14 21:36 UTC (permalink / raw)
To: Trond Myklebust; +Cc: Doug Whitesell (LKML), linux-kernel@vger.kernel.org
Ok, I'll do that....
Thanks
Sent from my iPhone
On Oct 14, 2007, at 2:32 PM, Trond Myklebust
<trond.myklebust@fys.uio.no> wrote:
>
> On Sun, 2007-10-14 at 14:00 -0700, Scott Petler wrote:
>> Doug,
>>
>> I thought that might do it, it does seem to work. I edited the
>> driver
>> line in my xorg.conf
>> from nvidia to nv and then,
>> <alt><ctrl> F1
>> login as root
>> /etc/init.d/gdm stop
>> /etc/init.d/gdm start
>>
>> It came back up with the same flashing crap on the second monitor,
>> so I
>> did it again with
>> the 2nd monitor turned off altogether, and I'll see how long it
>> will run
>> on the single monitor
>> without the nvidia driver without crashing (maybe forever...).
>>
>> Thanks,
>> Scott
>
> Please don't forget to reboot, though. The kernel will remain tainted
> until you've rebooted without loading the nvidia module.
>
> Cheers
> Trond
>
^ permalink raw reply [flat|nested] 9+ messages in thread
* PROBLEM: Kernel panic
@ 2008-07-02 6:49 Svein Larsen
2008-07-02 8:26 ` Frederik Deweerdt
0 siblings, 1 reply; 9+ messages in thread
From: Svein Larsen @ 2008-07-02 6:49 UTC (permalink / raw)
To: linux-kernel
Hi, I have no idea where to report and didnt find the REPORTING-BUGS
file in kernel tree so i send here. Hope it helps in some way.
- Svein
- Kernel panic
Linux version 2.6.9-55.ELsmp (brewbuilder@ls20-bc2-14.build.redhat.com)
(gcc version 3.4.6 20060404 (Red Hat 3.4.6-3)) #1 SMP Fri Apr 20
17:03:35 EDT 2007
Jul 2 07:52:56 web kernel: ------------[ cut here ]------------
Jul 2 07:52:56 web kernel: kernel BUG at fs/jbd/journal.c:576!
Jul 2 07:52:56 web kernel: invalid operand: 0000 [#1]
Jul 2 07:52:56 web kernel: SMP
Jul 2 07:52:56 web kernel: Modules linked in: autofs4 i2c_dev i2c_core
sunrpc ipt_REJECT ipt_state ip_conntrack iptable_filter ip_tables sr_mod
ide_scsi md5 ipv6 joydev button battery ac
uhci_hcd ehci_hcd hw_random shpchp e1000(U) floppy ata_piix libata sg
dm_snapshot dm_zero dm_mirror ext3 jbd dm_mod megaraid_mbox megaraid_mm
sd_mod scsi_mod
Jul 2 07:52:56 web kernel: CPU: 3
Jul 2 07:52:56 web kernel: EIP: 0060:[<f88846f1>] Not tainted VLI
Jul 2 07:52:56 web kernel: EFLAGS: 00010216 (2.6.9-55.ELsmp)
Jul 2 07:52:56 web kernel: EIP is at journal_next_log_block+0x39/0x83 [jbd]
Jul 2 07:52:56 web kernel: eax: 00000060 ebx: f7e00800 ecx:
d1a8edcc edx: f8887205
Jul 2 07:52:56 web kernel: esi: d87d418c edi: f7e00814 ebp:
d1a8ee14 esp: d1a8edc8
Jul 2 07:52:56 web kernel: ds: 007b es: 007b ss: 0068
Jul 2 07:52:56 web kernel: Process kjournald (pid: 2762,
threadinfo=d1a8e000 task=f6c4c2b0)
Jul 2 07:52:56 web kernel: Stack: f8887205 f888602f f88871f4 00000240
f888728f f7e00800 d87d418c ca53e23c
Jul 2 07:52:56 web kernel: f7d6f900 f888190f 00000000 00000000
00000e6c d87d4194 00000000 00000030
Jul 2 07:52:56 web kernel: dc6c917c f7e00800 e45187dc 00001a2e
00000000 f6c4c2b0 c012052d d1a8ee44
Jul 2 07:52:56 web kernel: Call Trace:
Jul 2 07:52:56 web kernel: [<f888190f>]
journal_commit_transaction+0x6d0/0xfd5 [jbd]
Jul 2 07:52:56 web kernel: [<c012052d>] autoremove_wake_function+0x0/0x2d
Jul 2 07:52:56 web kernel: [<c012052d>] autoremove_wake_function+0x0/0x2d
Jul 2 07:52:56 web kernel: [<f8883ec5>] kjournald+0xc7/0x219 [jbd]
Jul 2 07:52:56 web kernel: [<c012052d>] autoremove_wake_function+0x0/0x2d
Jul 2 07:52:56 web kernel: [<c012052d>] autoremove_wake_function+0x0/0x2d
Jul 2 07:52:56 web kernel: [<c011d69a>] schedule_tail+0x31/0xae
Jul 2 07:52:56 web kernel: [<f8883df8>] commit_timeout+0x0/0x5 [jbd]
Jul 2 07:52:56 web kernel: [<f8883dfe>] kjournald+0x0/0x219 [jbd]
Jul 2 07:52:56 web kernel: [<c01041f5>] kernel_thread_helper+0x5/0xb
Jul 2 07:52:56 web kernel: Code: 51 03 a5 c7 83 bb c4 00 00 00 01 77 29
68 8f 72 88 f8 68 40 02 00 00 68 f4 71 88 f8 68 2f 60 88 f8 68 05 72 88
f8 e8 01 e2 89 c7 <0f> 0b 40 02 f4 71 88 f8 83 c4 14 ff 8b c4 00 00 00
8b b3 bc 00
Jul 2 07:52:56 web kernel: <0>Fatal exception: panic in 5 seconds
* /proc/cpuinfo:
processor : 0
vendor_id : GenuineIntel
cpu family : 15
model : 4
model name : Intel(R) Xeon(TM) CPU 3.40GHz
stepping : 10
cpu MHz : 3392.243
cache size : 2048 KB
physical id : 0
siblings : 2
core id : 0
cpu cores : 1
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 5
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov
pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm
constant_tsc pni monitor ds_cpl est cid xtpr
bogomips : 6787.31
processor : 1
vendor_id : GenuineIntel
cpu family : 15
model : 4
model name : Intel(R) Xeon(TM) CPU 3.40GHz
stepping : 10
cpu MHz : 3392.243
cache size : 2048 KB
physical id : 0
siblings : 2
core id : 0
cpu cores : 1
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 5
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov
pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm
constant_tsc pni monitor ds_cpl est cid xtpr
bogomips : 6783.48
processor : 2
vendor_id : GenuineIntel
cpu family : 15
model : 4
model name : Intel(R) Xeon(TM) CPU 3.40GHz
stepping : 10
cpu MHz : 3392.243
cache size : 2048 KB
physical id : 3
siblings : 2
core id : 3
cpu cores : 1
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 5
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov
pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm
constant_tsc pni monitor ds_cpl est cid xtpr
bogomips : 6783.76
processor : 3
vendor_id : GenuineIntel
cpu family : 15
model : 4
model name : Intel(R) Xeon(TM) CPU 3.40GHz
stepping : 10
cpu MHz : 3392.243
cache size : 2048 KB
physical id : 3
siblings : 2
core id : 3
cpu cores : 1
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 5
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov
pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm
constant_tsc pni monitor ds_cpl est cid xtpr
bogomips : 6783.50
*/proc/modules:
autofs4 25285 0 - Live 0xf8b93000
i2c_dev 14529 0 - Live 0xf8b8e000
i2c_core 26049 1 i2c_dev, Live 0xf8b86000
sunrpc 143909 1 - Live 0xf8ba5000
ipt_REJECT 10689 1 - Live 0xf8a11000
ipt_state 5953 25 - Live 0xf8a09000
ip_conntrack 46085 1 ipt_state, Live 0xf8a15000
iptable_filter 6977 1 - Live 0xf8870000
ip_tables 22721 3 ipt_REJECT,ipt_state,iptable_filter, Live 0xf89f7000
sr_mod 20965 0 - Live 0xf89b8000
ide_scsi 20553 0 [permanent], Live 0xf89b1000
md5 8129 1 - Live 0xf88e5000
ipv6 243425 69 - Live 0xf8a3f000
joydev 14465 0 - Live 0xf88f2000
button 10705 0 - Live 0xf88dd000
battery 12997 0 - Live 0xf88f7000
ac 8901 0 - Live 0xf88e1000
uhci_hcd 33241 0 - Live 0xf88e8000
ehci_hcd 32325 0 - Live 0xf88aa000
hw_random 9685 0 - Live 0xf889c000
shpchp 85061 0 - Live 0xf89e1000
e1000 95060 0 - Live 0xf8927000
floppy 58193 0 - Live 0xf8917000
ata_piix 19141 0 - Live 0xf88a4000
libata 106141 1 ata_piix, Live 0xf88fc000
sg 38369 0 - Live 0xf88d2000
dm_snapshot 21093 0 - Live 0xf888f000
dm_zero 6337 0 - Live 0xf886b000
dm_mirror 31173 0 - Live 0xf8876000
ext3 119113 8 - Live 0xf88b3000
jbd 59609 1 ext3, Live 0xf887f000
dm_mod 64617 17 dm_snapshot,dm_zero,dm_mirror, Live 0xf882f000
megaraid_mbox 37329 4 - Live 0xf8860000
megaraid_mm 17777 1 megaraid_mbox, Live 0xf8829000
sd_mod 20545 7 - Live 0xf8822000
scsi_mod 119757 6 sr_mod,ide_scsi,libata,sg,megaraid_mbox,sd_mod, Live
0xf8841000
*/proc/ioports:
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-006f : keyboard
0070-0077 : rtc
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
01f0-01f7 : ide2
03c0-03df : vga+
03f6-03f6 : ide2
03f8-03ff : serial
0800-087f : 0000:00:1f.0
0800-0803 : PM1a_EVT_BLK
0804-0805 : PM1a_CNT_BLK
0808-080b : PM_TMR
0828-082f : GPE0_BLK
0880-08bf : 0000:00:1f.0
bca0-bcbf : 0000:00:1d.2
bca0-bcbf : uhci_hcd
bcc0-bcdf : 0000:00:1d.1
bcc0-bcdf : uhci_hcd
bce0-bcff : 0000:00:1d.0
bce0-bcff : uhci_hcd
c800-c8ff : 0000:0b:0d.0
cc70-cc7f : 0000:0b:06.0
cc80-ccbf : 0000:0b:05.1
cc80-cc87 : serial
ccd0-ccd3 : 0000:0b:06.0
ccd8-ccdf : 0000:0b:06.0
cce4-cce7 : 0000:0b:06.0
cce8-ccef : 0000:0b:05.0
ccf0-ccf7 : 0000:0b:06.0
ccf8-ccff : 0000:0b:05.0
d000-efff : PCI Bus #05
d000-dfff : PCI Bus #07
dcc0-dcff : 0000:07:08.0
dcc0-dcff : e1000
e000-efff : PCI Bus #06
ecc0-ecff : 0000:06:07.0
ecc0-ecff : e1000
fc00-fc0f : 0000:00:1f.1
fc00-fc07 : ide2
* /proc/iomem:
00000000-0009ffff : System RAM
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000cb000-000cbfff : Adapter ROM
000cc000-000ccfff : Adapter ROM
000cd000-000d0bff : Adapter ROM
000d1000-000d31ff : Adapter ROM
000d3800-000d3dff : Adapter ROM
000f0000-000fffff : System ROM
00100000-bffbffff : System RAM
00100000-002d6bdb : Kernel code
002d6bdc-0039537f : Kernel data
bffc0000-bffcfbff : ACPI Tables
bffcfc00-bfffefff : reserved
c0000000-c00003ff : 0000:00:1f.1
c8000000-cfffffff : 0000:0b:0d.0
d7f00000-d7f7ffff : 0000:0b:05.1
d7fff000-d7ffffff : 0000:0b:05.0
d8000000-d80fffff : PCI Bus #01
d8000000-d80fffff : PCI Bus #02
d80f0000-d80fffff : 0000:02:0e.0
d80f0000-d80fffff : MegaRAID: LSI Logic Corporation
df4e0000-df4effff : 0000:0b:0d.0
df4fec00-df4fecff : 0000:0b:06.0
df4fec00-df4fecff : SiI680
df4ff000-df4fffff : 0000:0b:05.1
df600000-df6fffff : PCI Bus #08
df700000-dfbfffff : PCI Bus #05
df800000-df9fffff : PCI Bus #07
df8e0000-df8fffff : 0000:07:08.0
df8e0000-df8fffff : e1000
dfa00000-dfbfffff : PCI Bus #06
dfae0000-dfafffff : 0000:06:07.0
dfae0000-dfafffff : e1000
dfc00000-dfefffff : PCI Bus #01
dfd00000-dfefffff : PCI Bus #02
dfdc0000-dfdfffff : 0000:02:0e.0
dfdc0000-dfdfffff : MegaRAID: LSI Logic Corporation
dff00000-dff003ff : 0000:00:1d.7
dff00000-dff003ff : ehci_hcd
e0000000-fec8ffff : reserved
fed00000-fed003ff : reserved
fee00000-fee0ffff : reserved
ffb00000-ffffffff : reserved
*PCI Info:
00:00.0 Host bridge: Intel Corporation E7520 Memory Controller Hub (rev 09)
Subsystem: Dell: Unknown device 016d
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [40] Vendor Specific Information
00:02.0 PCI bridge: Intel Corporation E7525/E7520/E7320 PCI Express Port
A (rev 09) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=00, secondary=01, subordinate=03, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: dfc00000-dfefffff
Prefetchable memory behind bridge: 00000000d8000000-00000000d8000000
Secondary status: 66Mhz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR+ <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Message Signalled Interrupts: 64bit- Queue=0/1 Enable-
Address: fee00000 Data: 0000
Capabilities: [64] Express Root Port (Slot-) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 256 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 2
Link: Latency L0s <4us, L1 unlimited
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [100] Advanced Error Reporting
00:04.0 PCI bridge: Intel Corporation E7525/E7520 PCI Express Port B
(rev 09) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
Secondary status: 66Mhz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Message Signalled Interrupts: 64bit- Queue=0/1 Enable-
Address: fee00000 Data: 0000
Capabilities: [64] Express Root Port (Slot-) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 4
Link: Latency L0s <4us, L1 unlimited
Link: ASPM Disabled RCB 64 bytes Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [100] Advanced Error Reporting
00:05.0 PCI bridge: Intel Corporation E7520 PCI Express Port B1 (rev 09)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=00, secondary=05, subordinate=07, sec-latency=0
I/O behind bridge: 0000d000-0000efff
Memory behind bridge: df700000-dfbfffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
Secondary status: 66Mhz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR+ <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Message Signalled Interrupts: 64bit- Queue=0/1 Enable-
Address: fee00000 Data: 0000
Capabilities: [64] Express Root Port (Slot-) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 256 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s, Port 5
Link: Latency L0s <4us, L1 unlimited
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x4
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [100] Advanced Error Reporting
00:06.0 PCI bridge: Intel Corporation E7520 PCI Express Port C (rev 09)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=00, secondary=08, subordinate=0a, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: df600000-df6fffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
Secondary status: 66Mhz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR+ <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Message Signalled Interrupts: 64bit- Queue=0/1 Enable-
Address: fee00000 Data: 0000
Capabilities: [64] Express Root Port (Slot-) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 256 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 6
Link: Latency L0s <4us, L1 unlimited
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [100] Advanced Error Reporting
00:1d.0 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
UHCI Controller #1 (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell: Unknown device 016d
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 169
Region 4: I/O ports at bce0 [size=32]
00:1d.1 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
UHCI Controller #2 (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell: Unknown device 016d
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 177
Region 4: I/O ports at bcc0 [size=32]
00:1d.2 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
UHCI Controller #3 (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell: Unknown device 016d
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 185
Region 4: I/O ports at bca0 [size=32]
00:1d.7 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2
EHCI Controller (rev 02) (prog-if 20 [EHCI])
Subsystem: Dell: Unknown device 016d
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 193
Region 0: Memory at dff00000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev c2) (prog-if
00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=0b, subordinate=0b, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: df400000-df5fffff
Prefetchable memory behind bridge: c8000000-d7ffffff
Secondary status: 66Mhz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC
Interface Bridge (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE
Controller (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Dell: Unknown device 016d
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 0
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at fc00 [size=16]
Region 5: Memory at c0000000 (32-bit, non-prefetchable) [size=1K]
01:00.0 PCI bridge: Intel Corporation 80332 [Dobson] I/O processor
(A-Segment Bridge) (rev 06) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=01, secondary=02, subordinate=02, sec-latency=64
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: dfd00000-dfefffff
Prefetchable memory behind bridge: 00000000d8000000-00000000d8000000
Secondary status: 66Mhz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [44] Express PCI/PCI-X Bridge IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 256 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 0
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Capabilities: [5c] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [6c] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d8] PCI-X bridge device.
Secondary Status: 64bit+, 133MHz+, SCD-, USC-, SCO-, SRD- Freq=133MHz
Status: Bus=1 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, SCO-, SRD-
: Upstream: Capacity=65535, Commitment Limit=65535
: Downstream: Capacity=65535, Commitment Limit=65535
Capabilities: [100] Advanced Error Reporting
Capabilities: [300] Power Budgeting
01:00.2 PCI bridge: Intel Corporation 80332 [Dobson] I/O processor
(B-Segment Bridge) (rev 06) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=01, secondary=03, subordinate=03, sec-latency=64
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
Secondary status: 66Mhz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [44] Express PCI/PCI-X Bridge IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 256 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 0
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Capabilities: [5c] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [6c] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d8] PCI-X bridge device.
Secondary Status: 64bit+, 133MHz+, SCD-, USC-, SCO-, SRD- Freq=133MHz
Status: Bus=1 Dev=0 Func=2 64bit- 133MHz- SCD- USC-, SCO-, SRD-
: Upstream: Capacity=65535, Commitment Limit=65535
: Downstream: Capacity=65535, Commitment Limit=65535
Capabilities: [100] Advanced Error Reporting
Capabilities: [300] Power Budgeting
02:0e.0 RAID bus controller: Dell PowerEdge Expandable RAID controller 4
(rev 06)
Subsystem: Dell PowerEdge Expandable RAID Controller 4e/Di
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping+ SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (32000ns min), Cache Line Size 10
Interrupt: pin A routed to IRQ 201
Region 0: Memory at d80f0000 (32-bit, prefetchable) [size=64K]
Region 2: Memory at dfdc0000 (32-bit, non-prefetchable) [size=256K]
Expansion ROM at dfe00000 [disabled] [size=128K]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [e0] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=0 OST=3
Status: Bus=2 Dev=14 Func=0 64bit+ 133MHz+ SCD- USC-, DC=bridge,
DMMRBC=1, DMOST=3, DMCRS=1, RSCEM-
05:00.0 PCI bridge: Intel Corporation 6700PXH PCI Express-to-PCI Bridge
A (rev 09) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=05, secondary=06, subordinate=06, sec-latency=32
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: dfa00000-dfbfffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
Secondary status: 66Mhz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [44] Express PCI/PCI-X Bridge IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 256 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 0
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Capabilities: [5c] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [6c] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d8] PCI-X bridge device.
Secondary Status: 64bit+, 133MHz+, SCD-, USC-, SCO-, SRD- Freq=conv
Status: Bus=5 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, SCO-, SRD-
: Upstream: Capacity=65535, Commitment Limit=65535
: Downstream: Capacity=65535, Commitment Limit=65535
Capabilities: [100] Advanced Error Reporting
Capabilities: [300] Power Budgeting
05:00.2 PCI bridge: Intel Corporation 6700PXH PCI Express-to-PCI Bridge
B (rev 09) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=05, secondary=07, subordinate=07, sec-latency=32
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: df800000-df9fffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
Secondary status: 66Mhz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [44] Express PCI/PCI-X Bridge IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 256 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 0
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Capabilities: [5c] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [6c] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d8] PCI-X bridge device.
Secondary Status: 64bit+, 133MHz+, SCD-, USC-, SCO-, SRD- Freq=conv
Status: Bus=5 Dev=0 Func=2 64bit- 133MHz- SCD- USC-, SCO-, SRD-
: Upstream: Capacity=65535, Commitment Limit=65535
: Downstream: Capacity=65535, Commitment Limit=65535
Capabilities: [100] Advanced Error Reporting
Capabilities: [300] Power Budgeting
06:07.0 Ethernet controller: Intel Corporation 82541GI Gigabit Ethernet
Controller (rev 05)
Subsystem: Dell PowerEdge 1850
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (63750ns min), Cache Line Size 10
Interrupt: pin A routed to IRQ 209
Region 0: Memory at dfae0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at ecc0 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [e4] PCI-X non-bridge device.
Command: DPERE- ERO+ RBC=0 OST=0
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple,
DMMRBC=2, DMOST=0, DMCRS=0, RSCEM-
07:08.0 Ethernet controller: Intel Corporation 82541GI Gigabit Ethernet
Controller (rev 05)
Subsystem: Dell PowerEdge 1850
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (63750ns min), Cache Line Size 10
Interrupt: pin A routed to IRQ 217
Region 0: Memory at df8e0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at dcc0 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [e4] PCI-X non-bridge device.
Command: DPERE- ERO+ RBC=0 OST=0
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple,
DMMRBC=2, DMOST=0, DMCRS=0, RSCEM-
08:00.0 PCI bridge: Intel Corporation 6700PXH PCI Express-to-PCI Bridge
A (rev 09) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=08, secondary=09, subordinate=09, sec-latency=64
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
Secondary status: 66Mhz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [44] Express PCI/PCI-X Bridge IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 256 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 0
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Capabilities: [5c] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [6c] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d8] PCI-X bridge device.
Secondary Status: 64bit+, 133MHz+, SCD-, USC-, SCO-, SRD- Freq=133MHz
Status: Bus=8 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, SCO-, SRD-
: Upstream: Capacity=65535, Commitment Limit=65535
: Downstream: Capacity=65535, Commitment Limit=65535
Capabilities: [100] Advanced Error Reporting
Capabilities: [300] Power Budgeting
08:00.2 PCI bridge: Intel Corporation 6700PXH PCI Express-to-PCI Bridge
B (rev 09) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=08, secondary=0a, subordinate=0a, sec-latency=64
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
Secondary status: 66Mhz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [44] Express PCI/PCI-X Bridge IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 256 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 0
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Capabilities: [5c] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [6c] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d8] PCI-X bridge device.
Secondary Status: 64bit+, 133MHz+, SCD-, USC-, SCO-, SRD- Freq=133MHz
Status: Bus=8 Dev=0 Func=2 64bit- 133MHz- SCD- USC-, SCO-, SRD-
: Upstream: Capacity=65535, Commitment Limit=65535
: Downstream: Capacity=65535, Commitment Limit=65535
Capabilities: [100] Advanced Error Reporting
Capabilities: [300] Power Budgeting
0b:05.0 Class ff00: Dell Remote Access Card 4 Daughter Card
Subsystem: Dell Remote Access Card 4 Daughter Card
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size 10
Interrupt: pin A routed to IRQ 225
Region 0: Memory at d7fff000 (32-bit, prefetchable) [size=4K]
Region 1: I/O ports at ccf8 [size=8]
Region 2: I/O ports at cce8 [size=8]
Expansion ROM at df500000 [disabled] [size=64K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0b:05.1 Class ff00: Dell Remote Access Card 4 Daughter Card Virtual UART
Subsystem: Dell Remote Access Card 4 Daughter Card Virtual UART
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 233
Region 0: Memory at df4ff000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at cc80 [size=64]
Region 2: Memory at d7f00000 (32-bit, prefetchable) [size=512K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0b:05.2 Class ff00: Dell Remote Access Card 4 Daughter Card SMIC interface
Subsystem: Dell Remote Access Card 4 Daughter Card SMIC interface
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0b:06.0 IDE interface: Silicon Image, Inc. PCI0680 Ultra ATA-133 Host
Controller (rev 02) (prog-if 85 [Master SecO PriO])
Subsystem: Silicon Image, Inc. PCI0680 Ultra ATA-133 Host Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size 01
Interrupt: pin A routed to IRQ 193
Region 0: I/O ports at ccf0 [size=8]
Region 1: I/O ports at cce4 [size=4]
Region 2: I/O ports at ccd8 [size=8]
Region 3: I/O ports at ccd0 [size=4]
Region 4: I/O ports at cc70 [size=16]
Region 5: Memory at df4fec00 (32-bit, non-prefetchable) [size=256]
Expansion ROM at df500000 [disabled] [size=512K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
0b:0d.0 VGA compatible controller: ATI Technologies Inc Radeon RV100 QY
[Radeon 7000/VE] (prog-if 00 [VGA])
Subsystem: Dell: Unknown device 016d
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr-
Stepping+ SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min), Cache Line Size 10
Interrupt: pin A routed to IRQ 185
Region 0: Memory at c8000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at c800 [size=256]
Region 2: Memory at df4e0000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: PROBLEM: Kernel panic
2008-07-02 6:49 PROBLEM: Kernel panic Svein Larsen
@ 2008-07-02 8:26 ` Frederik Deweerdt
0 siblings, 0 replies; 9+ messages in thread
From: Frederik Deweerdt @ 2008-07-02 8:26 UTC (permalink / raw)
To: Svein Larsen; +Cc: linux-kernel
On Wed, Jul 02, 2008 at 08:49:56AM +0200, Svein Larsen wrote:
> Hi, I have no idea where to report and didnt find the REPORTING-BUGS file
> in kernel tree so i send here. Hope it helps in some way.
>
> - Svein
>
> Linux version 2.6.9-55.ELsmp (brewbuilder@ls20-bc2-14.build.redhat.com)
You should report this to Red Hat.
Regards,
Frederik
^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2008-07-02 8:27 UTC | newest]
Thread overview: 9+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-07-02 6:49 PROBLEM: Kernel panic Svein Larsen
2008-07-02 8:26 ` Frederik Deweerdt
-- strict thread matches above, loose matches on Subject: below --
2007-10-13 22:48 PROBLEM: kernel panic Scott Petler
2007-10-14 20:24 ` Trond Myklebust
2007-10-14 20:44 ` Scott Petler
2007-10-14 20:51 ` Doug Whitesell (LKML)
2007-10-14 21:00 ` Scott Petler
2007-10-14 21:32 ` Trond Myklebust
2007-10-14 21:36 ` Scott Petler
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox