2.6.27rc1 cannot boot more than 8CPUs

2.6.27rc1 cannot boot more than 8CPUs

[Jeff Chua]

I've a Dell R900 with 4 quad-core Xeon processors (total 16CPUs), but
can only managed to boot up with CONFIG_NR_CPUS=8. Setting
CONFIG_NR_CPUS=16 causes the kernel to hang while booting.


Here's the dmesg with CONFIG_NR_CPUS=8 ...

CPU6: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#6]: passed.
CPU 7 irqstacks, hard=c0526000 soft=c051e000
Booting processor 7/26 ip 6000
Initializing CPU#7
Calibrating delay using timer specific routine.. 3723.85 BogoMIPS (lpj=7447700)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 6
CPU: Processor Core ID: 2
x86 PAT enabled: cpu 7, old 0x7040600070406, new 0x7010600070106
CPU7: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#7]: passed.
Brought up 8 CPUs
Total of 8 processors activated (29790.71 BogoMIPS).
net_namespace: 596 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16


Here's the dmesg with CONFIG_NR_CPUS=16 ...
Booting processor 8/1 ip 6000
Initializing CPU#8
Calibrating delay using timer specific routine.. 3723.85 BogoMIPS (lpj=7447793)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
x86 PAT enabled: cpu 7, old 0x7040600070406, new 0x7010600070106
CPU8: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#8]: passed.
*** Hangs here ***


How can I debug this further? I'm using the latest linux git pull.


Thanks,
Jeff.

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Max Krasnyansky]

Jeff Chua wrote:
> I've a Dell R900 with 4 quad-core Xeon processors (total 16CPUs), but
> can only managed to boot up with CONFIG_NR_CPUS=8. Setting
> CONFIG_NR_CPUS=16 causes the kernel to hang while booting.

You could try booting CONFIG_NR_CPUS=16 with maxcpus=8 (kernel command line
option).

If it boots you can then try bringing the rest of the cpus online manually
	echo 1 > /sys/devices/system/cpu/cpu8/online
         ...
	echo 1 > /sys/devices/system/cpu/cpu15/online

Might get a better OOPS/BUG_ON/etc report.

Max

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Jeff Chua]

On Wed, Aug 6, 2008 at 11:31 AM, Max Krasnyansky <maxk@qualcomm.com> wrote:
> You could try booting CONFIG_NR_CPUS=16 with maxcpus=8 (kernel command line option).
> If it boots you can then try bringing the rest of the cpus online manually

Ok,  booted with CONFIG_NR_CPUS=16 with maxcpus=8, but can't find the
rest of the CPUs.

I can only find cpu0 to cpu7 ...


drwxr-xr-x  4 root root    0 Aug  6 19:38 cpu0
drwxr-xr-x  4 root root    0 Aug  6 19:38 cpu1
drwxr-xr-x  4 root root    0 Aug  6 19:38 cpu2
drwxr-xr-x  4 root root    0 Aug  6 19:38 cpu3
drwxr-xr-x  4 root root    0 Aug  6 19:38 cpu4
drwxr-xr-x  4 root root    0 Aug  6 19:38 cpu5
drwxr-xr-x  4 root root    0 Aug  6 19:38 cpu6
drwxr-xr-x  4 root root    0 Aug  6 19:38 cpu7
-r--r--r--  1 root root 4096 Aug  6 19:41 online
-r--r--r--  1 root root 4096 Aug  6 19:39 possible
-r--r--r--  1 root root 4096 Aug  6 19:38 present
-rw-r--r--  1 root root 4096 Aug  6 19:38 sched_mc_power_savings

# cat online
0-7
# cat possible
0-23
# cat present
0-7

Thanks,
Jeff.

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Max Krasnyansky]

Jeff Chua wrote:
> On Wed, Aug 6, 2008 at 11:31 AM, Max Krasnyansky <maxk@qualcomm.com> wrote:
>> You could try booting CONFIG_NR_CPUS=16 with maxcpus=8 (kernel command line option).
>> If it boots you can then try bringing the rest of the cpus online manually
> 
> Ok,  booted with CONFIG_NR_CPUS=16 with maxcpus=8, but can't find the
> rest of the CPUs.
> 
> I can only find cpu0 to cpu7 ...
> 
> 
> drwxr-xr-x  4 root root    0 Aug  6 19:38 cpu0
> drwxr-xr-x  4 root root    0 Aug  6 19:38 cpu1
> drwxr-xr-x  4 root root    0 Aug  6 19:38 cpu2
> drwxr-xr-x  4 root root    0 Aug  6 19:38 cpu3
> drwxr-xr-x  4 root root    0 Aug  6 19:38 cpu4
> drwxr-xr-x  4 root root    0 Aug  6 19:38 cpu5
> drwxr-xr-x  4 root root    0 Aug  6 19:38 cpu6
> drwxr-xr-x  4 root root    0 Aug  6 19:38 cpu7
> -r--r--r--  1 root root 4096 Aug  6 19:41 online
> -r--r--r--  1 root root 4096 Aug  6 19:39 possible
> -r--r--r--  1 root root 4096 Aug  6 19:38 present
> -rw-r--r--  1 root root 4096 Aug  6 19:38 sched_mc_power_savings
> 
> # cat online
> 0-7
> # cat possible
> 0-23
> # cat present
> 0-7

Are you running 32-bit kernel ?

Max

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Jeff Chua]

On Wed, Aug 6, 2008 at 11:54 AM, Max Krasnyansky <maxk@qualcomm.com> wrote:

> Are you running 32-bit kernel ?

Yes. But, does it matter?

Thanks,
Jeff.

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Max Krasnyansky]

Jeff Chua wrote:
> On Wed, Aug 6, 2008 at 11:54 AM, Max Krasnyansky <maxk@qualcomm.com> wrote:
> 
>> Are you running 32-bit kernel ?
> 
> Yes. But, does it matter?

It used to. 64-bit kernel used to handle maxcpus option as documented in the 
Documentation/cpu-hotplug.txt and 32-bit one was broken.
I just looked at the latest code and realized that both are now broken. They 
ignore cpu id > maxcpus instead of not-booting them.

I'll send a patch that fixes that tomorrow.

Max

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Li Zefan]

Max Krasnyansky wrote:
> Jeff Chua wrote:
>> On Wed, Aug 6, 2008 at 11:54 AM, Max Krasnyansky <maxk@qualcomm.com>
>> wrote:
>>
>>> Are you running 32-bit kernel ?
>>
>> Yes. But, does it matter?
> 
> It used to. 64-bit kernel used to handle maxcpus option as documented in
> the Documentation/cpu-hotplug.txt and 32-bit one was broken.
> I just looked at the latest code and realized that both are now broken.
> They ignore cpu id > maxcpus instead of not-booting them.
> 

Yes. I have an x86_64 box with 4 cpus, but yesterday when I booted up with maxcpus=2,
I didn't see the other 2 cpus.

> I'll send a patch that fixes that tomorrow.
> 

greate :)

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Max Krasnyansky]

Li Zefan wrote:
> Max Krasnyansky wrote:
>> Jeff Chua wrote:
>>> On Wed, Aug 6, 2008 at 11:54 AM, Max Krasnyansky <maxk@qualcomm.com>
>>> wrote:
>>>
>>>> Are you running 32-bit kernel ?
>>> Yes. But, does it matter?
>> It used to. 64-bit kernel used to handle maxcpus option as documented in
>> the Documentation/cpu-hotplug.txt and 32-bit one was broken.
>> I just looked at the latest code and realized that both are now broken.
>> They ignore cpu id > maxcpus instead of not-booting them.
>>
> 
> Yes. I have an x86_64 box with 4 cpus, but yesterday when I booted up with maxcpus=2,
> I didn't see the other 2 cpus.
> 
>> I'll send a patch that fixes that tomorrow.
>>
> 
> greate :)

I just sent it and CC'ed both of you guys.
	[PATCH] Resurect proper handling of maxcpus= kernel option

Jeff, maybe you can try again booting with maxcpus=8 and then bringing 
them online one by one to see where/what fails.

Max

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Jeff Chua]

On Wed, Aug 6, 2008 at 11:50 AM, Yinghai Lu <yhlu.kernel@gmail.com> wrote:

> 32bit or 64 bit?

32bit.

    High Memory Support (64GB)  --->
-*- PAE (Physical Address Extension) Support
    Memory model (Sparse Memory)  --->
-*- 64 bit Memory and IO resources (EXPERIMENTAL)
[*] Allocate 3rd-level pagetables from highmem


> can you post full demsg?

The following is "cut&paste" ... (gmail is not the a good way to do
this.) for the 8 cpus that I managed to boot.

routine.. 3723.90 BogoMIPS (lpj=7447810)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 6
CPU: Processor Core ID: 0
x86 PAT enabled: cpu 3, old 0x7040600070406, new 0x7010600070106
CPU3: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#3]: passed.
CPU 4 irqstacks, hard=c053f000 soft=c051f000
Booting processor 4/2 ip 6000
Initializing CPU#4
Calibrating delay using timer specific routine.. 3723.87 BogoMIPS (lpj=7447748)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 2
x86 PAT enabled: cpu 4, old 0x7040600070406, new 0x7010600070106
CPU4: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#4]: passed.
CPU 5 irqstacks, hard=c0540000 soft=c0520000
Booting processor 5/10 ip 6000
Initializing CPU#5
Calibrating delay using timer specific routine.. 3723.89 BogoMIPS (lpj=7447794)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 2
x86 PAT enabled: cpu 5, old 0x7040600070406, new 0x7010600070106
CPU5: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#5]: passed.
CPU 6 irqstacks, hard=c0541000 soft=c0521000
Booting processor 6/18 ip 6000
Initializing CPU#6
Calibrating delay using timer specific routine.. 3723.89 BogoMIPS (lpj=7447791)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 4
CPU: Processor Core ID: 2
x86 PAT enabled: cpu 6, old 0x7040600070406, new 0x7010600070106
CPU6: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#6]: passed.
CPU 7 irqstacks, hard=c0542000 soft=c0522000
Booting processor 7/26 ip 6000
Initializing CPU#7
Calibrating delay using timer specific routine.. 3723.88 BogoMIPS (lpj=7447769)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 6
CPU: Processor Core ID: 2
x86 PAT enabled: cpu 7, old 0x7040600070406, new 0x7010600070106
CPU7: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#7]: passed.
Brought up 8 CPUs
Total of 8 processors activated (29791.07 BogoMIPS).
net_namespace: 596 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
No dock devices found.
ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
ACPI: bus type pci registered
PCI: Using configuration type 1 for base access
PCI: Dell PowerEdge R900 detected, enabling pci=bfsort.
ACPI: EC: Look up EC in DSDT
ACPI: BIOS _OSI(Linux) query ignored
ACPI: DMI System Vendor: Dell Inc.
ACPI: DMI Product Name: PowerEdge R900
ACPI: DMI Product Version:
ACPI: DMI Board Name: 0C764H
ACPI: DMI BIOS Vendor: Dell Inc.
ACPI: DMI BIOS Date: 03/23/2008
ACPI: Please send DMI info above to linux-acpi@vger.kernel.org
ACPI: If "acpi_osi=Linux" works better, please notify linux-acpi@vger.kernel.org
ACPI: Interpreter enabled
ACPI: (supports S0 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
pci 0000:00:00.0: PME# disabled
pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
pci 0000:00:01.0: PME# disabled
pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
pci 0000:00:02.0: PME# disabled
pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
pci 0000:00:03.0: PME# disabled
pci 0000:00:04.0: PME# supported from D0 D3hot D3cold
pci 0000:00:04.0: PME# disabled
pci 0000:00:06.0: PME# supported from D0 D3hot D3cold
pci 0000:00:06.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:16:00.0: PME# supported from D0 D3hot D3cold
pci 0000:16:00.0: PME# disabled
pci 0000:16:00.3: PME# supported from D0 D3hot D3cold
pci 0000:16:00.3: PME# disabled
pci 0000:17:00.0: PME# supported from D0 D3hot D3cold
pci 0000:17:00.0: PME# disabled
pci 0000:17:01.0: PME# supported from D0 D3hot D3cold
pci 0000:17:01.0: PME# disabled
pci 0000:19:00.0: supports D1
pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
pci 0000:01:00.0: PME# disabled
pci 0000:02:01.0: PME# supported from D0 D3hot D3cold
pci 0000:02:01.0: PME# disabled
pci 0000:02:02.0: PME# supported from D0 D3hot D3cold
pci 0000:02:02.0: PME# disabled
pci 0000:02:03.0: PME# supported from D0 D3hot D3cold
pci 0000:02:03.0: PME# disabled
pci 0000:02:04.0: PME# supported from D0 D3hot D3cold
pci 0000:02:04.0: PME# disabled
pci 0000:02:05.0: PME# supported from D0 D3hot D3cold
pci 0000:02:05.0: PME# disabled
pci 0000:0a:00.0: PME# supported from D0 D3hot D3cold
pci 0000:0a:00.0: PME# disabled
pci 0000:0b:00.0: PME# supported from D3hot D3cold
pci 0000:0b:00.0: PME# disabled
pci 0000:08:00.0: PME# supported from D0 D3hot D3cold
pci 0000:08:00.0: PME# disabled
pci 0000:09:00.0: PME# supported from D3hot D3cold
pci 0000:09:00.0: PME# disabled
pci 0000:06:00.0: PME# supported from D0 D3hot D3cold
pci 0000:06:00.0: PME# disabled
pci 0000:07:00.0: PME# supported from D3hot D3cold
pci 0000:07:00.0: PME# disabled
pci 0000:04:00.0: PME# supported from D0 D3hot D3cold
pci 0000:04:00.0: PME# disabled
pci 0000:05:00.0: PME# supported from D3hot D3cold
pci 0000:05:00.0: PME# disabled
pci 0000:0c:00.0: PME# supported from D0 D3hot D3cold
pci 0000:0d:02.0: PME# disabled
pci 0000:0d:04.0: PME# supported from D0 D3hot D3cold
pci 0000:0d:04.0: PME# disabled
pci 0000:10:00.0: PME# supported from D0 D3hot D3cold
pci 0000:10:00.0: PME# disabled
pci 0000:11:02.0: PME# supported from D0 D3hot D3cold
pci 0000:11:02.0: PME# disabled
pci 0000:11:04.0: PME# supported from D0 D3hot D3cold
pci 0000:11:04.0: PME# disabled
pci 0000:1b:0c.0: supports D1
pci 0000:1b:0c.0: supports D2
pci 0000:00:1e.0: transparent bridge
bus 00 -> node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2.UPST._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2.UPST.DWN1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2.UPST.DWN2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3.UPST.DWN2.BCOM._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3.UPST.DWN3.BCOM._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3.UPST.DWN4.BCOM._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3.UPST.DWN5.BCOM._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4.UPST.DWNB._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4.UPST.DWNC._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX6.UPST.DWNB._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX6.UPST.DWNC._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.SBEX._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.COMP._PRT]
ACPI: PCI Interrupt Link [LK00] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LK01] (IRQs 3 4 5 6 7 *10 11 12)
ACPI: PCI Interrupt Link [LK02] (IRQs 3 4 5 *6 7 10 11 12)
ACPI: PCI Interrupt Link [LK03] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LK04] (IRQs 3 4 *5 6 7 10 11 12)
ACPI: PCI Interrupt Link [LK05] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LK06] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LK07] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
Switched to high resolution mode on CPU 0
Switched to high resolution mode on CPU 5
Switched to high resolution mode on CPU 6
Switched to high resolution mode on CPU 2
Switched to high resolution mode on CPU 4
Switched to high resolution mode on CPU 7
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 3
system 00:07: ioport range 0x800-0x87f has been reserved
system 00:07: ioport range 0x880-0x8bf has been reserved
system 00:07: ioport range 0x8c0-0x8df has been reserved
system 00:07: ioport range 0x8e0-0x8e3 has been reserved
system 00:07: ioport range 0x8f0-0x8f1 has been reserved
system 00:07: ioport range 0x900-0x900 has been reserved
system 00:07: ioport range 0xc00-0xc7f has been reserved
system 00:07: ioport range 0xca0-0xca7 has been reserved
system 00:07: ioport range 0xca9-0xcab has been reserved
system 00:07: ioport range 0xcad-0xcaf has been reserved
system 00:08: ioport range 0xca8-0xca8 has been reserved
system 00:08: ioport range 0xcac-0xcac has been reserved
system 00:09: iomem range 0xe0000000-0xefffffff could not be reserved
pci 0000:00:01.0: PCI bridge, secondary bus 0000:14
pci 0000:00:01.0:   IO window: disabled
pci 0000:00:01.0:   MEM window: disabled
pci 0000:00:01.0:   PREFETCH window: disabled
pci 0000:17:00.0: PCI bridge, secondary bus 0000:19
pci 0000:17:00.0:   IO window: 0xe000-0xefff
pci 0000:17:00.0:   MEM window: 0xde200000-0xde3fffff
pci 0000:17:00.0:   PREFETCH window: disabled
pci 0000:17:01.0: PCI bridge, secondary bus 0000:18
pci 0000:17:01.0:   IO window: disabled
pci 0000:17:01.0:   MEM window: disabled
pci 0000:17:01.0:   PREFETCH window: disabled
pci 0000:16:00.0: PCI bridge, secondary bus 0000:17
pci 0000:16:00.0:   IO window: 0xe000-0xefff
pci 0000:16:00.0:   MEM window: 0xde200000-0xde3fffff
pci 0000:16:00.0:   PREFETCH window: disabled
pci 0000:16:00.3: PCI bridge, secondary bus 0000:1a
pci 0000:16:00.3:   IO window: disabled
pci 0000:16:00.3:   MEM window: disabled
pci 0000:16:00.3:   PREFETCH window: disabled
pci 0000:00:02.0: PCI bridge, secondary bus 0000:16
pci 0000:00:02.0:   IO window: 0xe000-0xefff
pci 0000:00:02.0:   MEM window: 0xde100000-0xde3fffff
pci 0000:00:02.0:   PREFETCH window: disabled
pci 0000:02:01.0: PCI bridge, secondary bus 0000:03
pci 0000:02:01.0:   IO window: disabled
pci 0000:02:01.0:   MEM window: disabled
pci 0000:02:01.0:   PREFETCH window: disabled
pci 0000:0a:00.0: PCI bridge, secondary bus 0000:0b
pci 0000:0a:00.0:   IO window: disabled
pci 0000:0a:00.0:   MEM window: 0xd6000000-0xd7ffffff
pci 0000:0a:00.0:   PREFETCH window: disabled
pci 0000:02:02.0: PCI bridge, secondary bus 0000:0a
pci 0000:02:02.0:   IO window: disabled
pci 0000:02:02.0:   MEM window: 0xd6000000-0xd7ffffff
pci 0000:02:02.0:   PREFETCH window: disabled
pci 0000:08:00.0: PCI bridge, secondary bus 0000:09
pci 0000:08:00.0:   IO window: disabled
pci 0000:08:00.0:   MEM window: 0xd8000000-0xd9ffffff
pci 0000:08:00.0:   PREFETCH window: disabled
pci 0000:02:03.0: PCI bridge, secondary bus 0000:08
pci 0000:02:03.0:   IO window: disabled
pci 0000:02:03.0:   MEM window: 0xd8000000-0xd9ffffff
pci 0000:02:03.0:   PREFETCH window: disabled
pci 0000:06:00.0: PCI bridge, secondary bus 0000:07
pci 0000:06:00.0:   IO window: disabled
pci 0000:06:00.0:   MEM window: 0xda000000-0xdbffffff
pci 0000:06:00.0:   PREFETCH window: disabled
pci 0000:02:04.0: PCI bridge, secondary bus 0000:06
pci 0000:02:04.0:   IO window: disabled
pci 0000:02:04.0:   MEM window: 0xda000000-0xdbffffff
pci 0000:02:04.0:   PREFETCH window: disabled
pci 0000:04:00.0: PCI bridge, secondary bus 0000:05
pci 0000:04:00.0:   IO window: disabled
pci 0000:04:00.0:   MEM window: 0xdc000000-0xddffffff
pci 0000:04:00.0:   PREFETCH window: disabled
pci 0000:02:05.0: PCI bridge, secondary bus 0000:04
pci 0000:02:05.0:   IO window: disabled
pci 0000:02:05.0:   MEM window: 0xdc000000-0xddffffff
pci 0000:02:05.0:   PREFETCH window: disabled
pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
pci 0000:01:00.0:   IO window: disabled
pci 0000:01:00.0:   MEM window: 0xd6000000-0xddffffff
pci 0000:01:00.0:   PREFETCH window: disabled
pci 0000:00:03.0: PCI bridge, secondary bus 0000:01
pci 0000:00:03.0:   IO window: disabled
pci 0000:00:03.0:   MEM window: 0xd6000000-0xddffffff
pci 0000:00:03.0:   PREFETCH window: disabled
pci 0000:0d:02.0: PCI bridge, secondary bus 0000:0f
pci 0000:0d:02.0:   IO window: disabled
pci 0000:0d:02.0:   MEM window: disabled
pci 0000:0d:02.0:   PREFETCH window: disabled
pci 0000:0d:04.0: PCI bridge, secondary bus 0000:0e
pci 0000:0d:04.0:   IO window: disabled
pci 0000:0d:04.0:   MEM window: disabled
pci 0000:0d:04.0:   PREFETCH window: disabled
pci 0000:0c:00.0: PCI bridge, secondary bus 0000:0d
pci 0000:0c:00.0:   IO window: disabled
pci 0000:0c:00.0:   MEM window: disabled
pci 0000:0c:00.0:   PREFETCH window: disabled
pci 0000:00:04.0: PCI bridge, secondary bus 0000:0c
pci 0000:00:04.0:   IO window: disabled
pci 0000:00:04.0:   MEM window: disabled
pci 0000:00:04.0:   PREFETCH window: disabled
pci 0000:11:02.0: PCI bridge, secondary bus 0000:13
pci 0000:11:02.0:   IO window: disabled
pci 0000:11:02.0:   MEM window: disabled
pci 0000:11:02.0:   PREFETCH window: disabled
pci 0000:11:04.0: PCI bridge, secondary bus 0000:12
pci 0000:11:04.0:   IO window: disabled
pci 0000:11:04.0:   MEM window: disabled
pci 0000:11:04.0:   PREFETCH window: disabled
pci 0000:10:00.0: PCI bridge, secondary bus 0000:11
pci 0000:10:00.0:   IO window: disabled
pci 0000:00:06.0:   MEM window: disabled
pci 0000:00:06.0:   PREFETCH window: disabled
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:15
pci 0000:00:1c.0:   IO window: disabled
pci 0000:00:1c.0:   MEM window: disabled
pci 0000:00:1c.0:   PREFETCH window: disabled
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:1b
pci 0000:00:1e.0:   IO window: 0xd000-0xdfff
pci 0000:00:1e.0:   MEM window: 0xde400000-0xde4fffff
pci 0000:00:1e.0:   PREFETCH window: 0x000000c8000000-0x000000cfffffff
pci 0000:00:01.0: PCI INT A -> GSI 36 (level, low) -> IRQ 36
pci 0000:00:01.0: setting latency timer to 64
pci 0000:00:02.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:02.0: setting latency timer to 64
pci 0000:16:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:16:00.0: setting latency timer to 64
pci 0000:17:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:17:00.0: setting latency timer to 64
pci 0000:17:01.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
pci 0000:17:01.0: setting latency timer to 64
pci 0000:16:00.3: setting latency timer to 64
pci 0000:00:03.0: PCI INT A -> GSI 37 (level, low) -> IRQ 37
pci 0000:00:03.0: setting latency timer to 64
pci 0000:01:00.0: setting latency timer to 64
pci 0000:02:01.0: setting latency timer to 64
pci 0000:02:02.0: setting latency timer to 64
pci 0000:0a:00.0: setting latency timer to 64
pci 0000:02:03.0: setting latency timer to 64
pci 0000:08:00.0: setting latency timer to 64
pci 0000:02:04.0: setting latency timer to 64
pci 0000:06:00.0: setting latency timer to 64
pci 0000:02:05.0: setting latency timer to 64
pci 0000:04:00.0: setting latency timer to 64
pci 0000:04:00.0: setting latency timer to 64
pci 0000:00:04.0: PCI INT A -> GSI 32 (level, low) -> IRQ 32
pci 0000:00:04.0: setting latency timer to 64
pci 0000:0c:00.0: setting latency timer to 64
pci 0000:0d:02.0: setting latency timer to 64
pci 0000:0d:04.0: setting latency timer to 64
pci 0000:00:06.0: PCI INT A -> GSI 33 (level, low) -> IRQ 33
pci 0000:00:06.0: setting latency timer to 64
pci 0000:10:00.0: setting latency timer to 64
pci 0000:11:02.0: setting latency timer to 64
pci 0000:11:04.0: setting latency timer to 64
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
highmem bounce pool size: 64 pages
HugeTLB registered 2 MB page size, pre-allocated 0 pages
msgmni has been set to 1234
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered (default)
pci 0000:1b:0c.0: Boot video device
pcieport-driver 0000:00:01.0: setting latency timer to 64
pcieport-driver 0000:00:01.0: found MSI capability
pci_express 0000:00:01.0:pcie00: allocate port service
pcieport-driver 0000:00:02.0: setting latency timer to 64
pcieport-driver 0000:00:02.0: found MSI capability
pci_express 0000:00:02.0:pcie00: allocate port service
pci_express 0000:00:02.0:pcie00: allocate port service
pcieport-driver 0000:00:03.0: setting latency timer to 64
pcieport-driver 0000:00:03.0: found MSI capability
pci_express 0000:00:03.0:pcie00: allocate port service
pcieport-driver 0000:00:04.0: setting latency timer to 64
pcieport-driver 0000:00:04.0: found MSI capability
pci_express 0000:00:04.0:pcie00: allocate port service
pcieport-driver 0000:00:06.0: setting latency timer to 64
pcieport-driver 0000:00:06.0: found MSI capability
pci_express 0000:00:06.0:pcie00: allocate port service
pcieport-driver 0000:00:1c.0: setting latency timer to 64
pcieport-driver 0000:00:1c.0: found MSI capability
pci_express 0000:00:1c.0:pcie00: allocate port service
pci_express 0000:00:1c.0:pcie02: allocate port service
pcieport-driver 0000:01:00.0: setting latency timer to 64
pcieport-driver 0000:02:01.0: setting latency timer to 64
pcieport-driver 0000:02:01.0: found MSI capability
pcieport-driver 0000:02:02.0: setting latency timer to 64
pcieport-driver 0000:02:02.0: found MSI capability
pcieport-driver 0000:02:03.0: setting latency timer to 64
pcieport-driver 0000:02:03.0: found MSI capability
pcieport-driver 0000:02:04.0: setting latency timer to 64
pcieport-driver 0000:02:04.0: found MSI capability
pcieport-driver 0000:02:05.0: setting latency timer to 64
pcieport-driver 0000:02:05.0: found MSI capability
pcieport-driver 0000:0c:00.0: setting latency timer to 64
pcieport-driver 0000:0d:02.0: setting latency timer to 64
pcieport-driver 0000:0d:02.0: found MSI capability
pcieport-driver 0000:0d:04.0: setting latency timer to 64
pcieport-driver 0000:0d:04.0: found MSI capability
pcieport-driver 0000:10:00.0: setting latency timer to 64
pcieport-driver 0000:11:02.0: setting latency timer to 64
pcieport-driver 0000:11:02.0: found MSI capability
ACPI: Power Button (FF) [PWRF]
processor ACPI0007:00: registered as cooling_device0
processor ACPI0007:01: registered as cooling_device1
processor ACPI0007:02: registered as cooling_device2
processor ACPI0007:03: registered as cooling_device3
processor ACPI0007:04: registered as cooling_device4
processor ACPI0007:05: registered as cooling_device5
processor ACPI0007:06: registered as cooling_device6
processor ACPI0007:07: registered as cooling_device7
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.103
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
pcnet32.c:v1.35 21.Apr.2008 tsbogend@alpha.franken.de
Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.7.9 (July 18, 2008)
bnx2 0000:05:00.0: PCI INT A -> GSI 38 (level, low) -> IRQ 38
eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit
133MHz found at mem dc000000, IRQ 38, node addr 00:1e:c9:d9:84:57
bnx2 0000:07:00.0: PCI INT A -> GSI 37 (level, low) -> IRQ 37
eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit
133MHz found at mem da000000, IRQ 37, node addr 00:1e:c9:d9:84:59
bnx2 0000:09:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
eth2: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit
133MHz found at mem d8000000, IRQ 19, node addr 00:1e:c9:d9:84:5b
bnx2 0000:0b:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
eth3: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit
133MHz found at mem d6000000, IRQ 18, node addr 00:1e:c9:d9:84:5d
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
tun: Universal TUN/TAP device driver, 1.6
Uniform Multi-Platform E-IDE driver
ide_generic: please use "probe_mask=0x3f" module parameter for probing
all legacy ISA IDE ports
Probing IDE interface ide0...
hda: TSSTcorpDVD-ROM TS-L333A, ATAPI CD/DVD-ROM drive
Probing IDE interface ide1...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
megasas: 00.00.03.20-rc1 Mon. March 10 11:02:31 PDT 2008
megasas: 0x1000:0x0060:0x1028:0x1f0c: bus 25:slot 0:func 0
megaraid_sas 0000:19:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
megaraid_sas 0000:19:00.0: setting latency timer to 64
megasas: FW now in Ready state
scsi0 : LSI SAS based MegaRAID driver
scsi 0:0:0:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:1:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:2:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:3:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:4:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:5:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:6:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:7:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:32:0: Enclosure         DP       BACKPLANE        1.06 PQ: 0 ANSI: 5
scsi 0:2:0:0: Direct-Access     DELL     PERC 6/i         1.11 PQ: 0 ANSI: 5
Driver 'sd' needs updating - please use bus_type methods
sd 0:2:0:0: [sda] 710410240 512-byte hardware sectors (363730 MB)
sd 0:2:0:0: [sda] Write Protect is off
sd 0:2:0:0: [sda] Mode Sense: 1f 00 00 08
sd 0:2:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 0:2:0:0: [sda] 710410240 512-byte hardware sectors (363730 MB)
sd 0:2:0:0: [sda] Mode Sense: 1f 00 00 08
sd 0:2:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 0:2:0:0: [sda] 710410240 512-byte hardware sectors (363730 MB)
sd 0:2:0:0: [sda] Write Protect is off
sd 0:2:0:0: [sda] Mode Sense: 1f 00 00 08
sd 0:2:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
 sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12
sda13 sda14 sda15 >
sd 0:2:0:0: [sda] Attached SCSI disk
ata_piix 0000:00:1f.2: version 2.12
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
ata_piix 0000:00:1f.2: BAR 0: can't reserve I/O region [0x1f0-0x1f7]
ata_piix 0000:00:1f.2: failed to request/iomap BARs for port 0 (errno=-16)
ata_piix 0000:00:1f.2: BAR 2: can't reserve I/O region [0x170-0x177]
ata_piix 0000:00:1f.2: failed to request/iomap BARs for port 1 (errno=-16)
ata_piix 0000:00:1f.2: no available native port
Fusion MPT base driver 3.04.07
Copyright (c) 1999-2008 LSI Corporation
Fusion MPT SPI Host driver 3.04.07
ehci_hcd 0000:00:1d.7: PCI INT B -> GSI 21 (level, low) -> IRQ 21
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 21, io mem 0xde0ffc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
...

Re: 2.6.27rc1 cannot boot more than 8CPUs

[David Miller]

From: "Jeff Chua" <jeff.chua.linux@gmail.com>
Date: Wed, 6 Aug 2008 11:15:30 +0800

> I've a Dell R900 with 4 quad-core Xeon processors (total 16CPUs), but
> can only managed to boot up with CONFIG_NR_CPUS=8. Setting
> CONFIG_NR_CPUS=16 causes the kernel to hang while booting.
> 
> 
> Here's the dmesg with CONFIG_NR_CPUS=8 ...

Do you have lockdep enabled?  If sure, try turning that off.

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Jeff Chua]

On Wed, Aug 6, 2008 at 1:19 PM, David Miller <davem@davemloft.net> wrote:
> From: "Jeff Chua" <jeff.chua.linux@gmail.com>
> Date: Wed, 6 Aug 2008 11:15:30 +0800
> Do you have lockdep enabled?  If sure, try turning that off.

It's enabled by default, and I can't seem to disable it even if I
commented it out or delete it, it comes back after running "make".

CONFIG_X86_32=y
# CONFIG_X86_64 is not set
CONFIG_X86=y
CONFIG_ARCH_DEFCONFIG="arch/x86/configs/i386_defconfig"
# CONFIG_GENERIC_LOCKBREAK is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CMOS_UPDATE=y
CONFIG_CLOCKSOURCE_WATCHDOG=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_HAVE_LATENCYTOP_SUPPORT=y
CONFIG_FAST_CMPXCHG_LOCAL=y
CONFIG_MMU=y
CONFIG_ZONE_DMA=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y
CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_HWEIGHT=y


Thanks,
Jeff.

Re: 2.6.27rc1 cannot boot more than 8CPUs

[David Miller]

From: "Jeff Chua" <jeff.chua.linux@gmail.com>
Date: Wed, 6 Aug 2008 14:42:11 +0800

> On Wed, Aug 6, 2008 at 1:19 PM, David Miller <davem@davemloft.net> wrote:
> > From: "Jeff Chua" <jeff.chua.linux@gmail.com>
> > Date: Wed, 6 Aug 2008 11:15:30 +0800
> > Do you have lockdep enabled?  If sure, try turning that off.
> 
> It's enabled by default, and I can't seem to disable it even if I
> commented it out or delete it, it comes back after running "make".

You have to turn off CONFIG_PROVE_LOCKING, in fact just turn off
everything in the lock debugging section:

# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_MUTEXES is not set
# CONFIG_DEBUG_LOCK_ALLOC is not set
# CONFIG_PROVE_LOCKING is not set
# CONFIG_LOCK_STAT is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Jeff Chua]

On Wed, Aug 6, 2008 at 3:18 PM, David Miller <davem@davemloft.net> wrote:

> You have to turn off CONFIG_PROVE_LOCKING, in fact just turn off
> everything in the lock debugging section:
>
> # CONFIG_DEBUG_RT_MUTEXES is not set
> # CONFIG_RT_MUTEX_TESTER is not set
> # CONFIG_DEBUG_SPINLOCK is not set
> # CONFIG_DEBUG_MUTEXES is not set
> # CONFIG_DEBUG_LOCK_ALLOC is not set
> # CONFIG_PROVE_LOCKING is not set
> # CONFIG_LOCK_STAT is not set
> # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
> # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
>

I don't any option to turn these off. Still searching.

Jeff.

Re: 2.6.27rc1 cannot boot more than 8CPUs

[David Miller]

From: "Jeff Chua" <jeff.chua.linux@gmail.com>
Date: Wed, 6 Aug 2008 17:33:07 +0800

> On Wed, Aug 6, 2008 at 3:18 PM, David Miller <davem@davemloft.net> wrote:
> 
> > You have to turn off CONFIG_PROVE_LOCKING, in fact just turn off
> > everything in the lock debugging section:
> >
> > # CONFIG_DEBUG_RT_MUTEXES is not set
> > # CONFIG_RT_MUTEX_TESTER is not set
> > # CONFIG_DEBUG_SPINLOCK is not set
> > # CONFIG_DEBUG_MUTEXES is not set
> > # CONFIG_DEBUG_LOCK_ALLOC is not set
> > # CONFIG_PROVE_LOCKING is not set
> > # CONFIG_LOCK_STAT is not set
> > # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
> > # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
> >
> 
> I don't any option to turn these off. Still searching.

Maybe edit the ".config" file at the top level of the kernel
sources and then type "make oldconfig" ?!?!?!

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Jeff Chua]

On Wed, Aug 6, 2008 at 5:36 PM, David Miller <davem@davemloft.net> wrote:
> From: "Jeff Chua" <jeff.chua.linux@gmail.com>
> Date: Wed, 6 Aug 2008 17:33:07 +0800
>
>> On Wed, Aug 6, 2008 at 3:18 PM, David Miller <davem@davemloft.net> wrote:
>>
>> > You have to turn off CONFIG_PROVE_LOCKING, in fact just turn off
>> > everything in the lock debugging section:
> Maybe edit the ".config" file at the top level of the kernel
> sources and then type "make oldconfig" ?!?!?!

Ok, may be not as bad as I thought. These are not in .config meaning,
they are not set. So, it should ok. I'll test out these two first.

> CONFIG_X86_GENERICARCH=y
> CONFIG_X86_BIGSMP=y

Thanks,
Jeff.

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Yinghai Lu]

On Tue, Aug 5, 2008 at 11:42 PM, Jeff Chua <jeff.chua.linux@gmail.com> wrote:
> On Wed, Aug 6, 2008 at 1:19 PM, David Miller <davem@davemloft.net> wrote:
>> From: "Jeff Chua" <jeff.chua.linux@gmail.com>
>> Date: Wed, 6 Aug 2008 11:15:30 +0800
>> Do you have lockdep enabled?  If sure, try turning that off.
>
> It's enabled by default, and I can't seem to disable it even if I
> commented it out or delete it, it comes back after running "make".
>
> CONFIG_X86_32=y
> # CONFIG_X86_64 is not set
> CONFIG_X86=y
> CONFIG_ARCH_DEFCONFIG="arch/x86/configs/i386_defconfig"
> # CONFIG_GENERIC_LOCKBREAK is not set
> CONFIG_GENERIC_TIME=y
> CONFIG_GENERIC_CMOS_UPDATE=y
> CONFIG_CLOCKSOURCE_WATCHDOG=y
> CONFIG_GENERIC_CLOCKEVENTS=y
> CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
> CONFIG_LOCKDEP_SUPPORT=y
> CONFIG_STACKTRACE_SUPPORT=y
> CONFIG_HAVE_LATENCYTOP_SUPPORT=y
> CONFIG_FAST_CMPXCHG_LOCAL=y
> CONFIG_MMU=y
> CONFIG_ZONE_DMA=y
> CONFIG_GENERIC_ISA_DMA=y
> CONFIG_GENERIC_IOMAP=y
> CONFIG_GENERIC_BUG=y
> CONFIG_GENERIC_HWEIGHT=y
>
>

do you have

CONFIG_X86_GENERICARCH=y
CONFIG_X86_BIGSMP=y

8 more cpu need bigsmp mode.

YH

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Jeff Chua]

On Wed, Aug 6, 2008 at 4:49 PM, Yinghai Lu <yhlu.kernel@gmail.com> wrote:
> do you have
>
> CONFIG_X86_GENERICARCH=y
> CONFIG_X86_BIGSMP=y
>
> 8 more cpu need bigsmp mode.


Are these the ones that supposed to be set? Any, can't find a place to
set these using menuconfig.

# CONFIG_X86_GENERICARCH is not set
# CONFIG_X86_VSMP is not set

Thanks
Jeff.

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Jeff Chua]

On Wed, Aug 6, 2008 at 5:35 PM, Jeff Chua <jeff.chua.linux@gmail.com> wrote:
> On Wed, Aug 6, 2008 at 4:49 PM, Yinghai Lu <yhlu.kernel@gmail.com> wrote:
>> do you have
>> CONFIG_X86_GENERICARCH=y
>> CONFIG_X86_BIGSMP=y
>> 8 more cpu need bigsmp mode.
> Are these the ones that supposed to be set? Any, can't find a place to
> set these using menuconfig.
>
> # CONFIG_X86_GENERICARCH is not set
> # CONFIG_X86_VSMP is not set

Sorry, found it. These are not obvious. I had selected
"Subarchitecture Type (PC-compatible)" and could find a place to set
CONFIG_X86_GENERICARCH.

Just found it under " Subarchitecture Type (Generic architecture)",
and then it shows the CONFIG_X86_BIGSMP option.

Ok, compiling and testing now.

Jeff.

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Linus Torvalds]

On Wed, 6 Aug 2008, Jeff Chua wrote:
> 
> How can I debug this further? I'm using the latest linux git pull.

One trivial thing to try would be to just bisect it. I assume 2.6.26 is 
fine, so while it will take a few boots to try it out (there's 8111 
commits in between, so 13 reboots should do it), the advantage of 
bisection is that it's fairly straightforward to do even if you don't have 
any clue where the problem might lurk.

And with your machine, recompiling the kernel 13 times shouldn't take that 
long ;)

		Linus

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Jeff Chua]

On Wed, Aug 6, 2008 at 2:01 PM, Linus Torvalds
<torvalds@linux-foundation.org> wrote:

> One trivial thing to try would be to just bisect it. I assume 2.6.26 is
> fine, so while it will take a few boots to try it out (there's 8111
> commits in between, so 13 reboots should do it), the advantage of
> bisection is that it's fairly straightforward to do even if you don't have
> any clue where the problem might lurk.

Bisecting now.

Jeff.

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Jeff Chua]

On Wed, Aug 6, 2008 at 2:42 PM, Jeff Chua <jeff.chua.linux@gmail.com> wrote:
> On Wed, Aug 6, 2008 at 2:01 PM, Linus Torvalds
> <torvalds@linux-foundation.org> wrote:
>> One trivial thing to try would be to just bisect it. I assume 2.6.26 is
> Bisecting now.

Thanks to all the great helpful suggestions from everyone, and this
turns out that I just need to enable the following switches, so I
didn't bisect further, and since it's first machine that I've tried
with more than 8 CPUs so I wasn't sure whether 2.6.16 has the same
problem, but if you wish, I could give 2.6.16 a try.

> CONFIG_X86_GENERICARCH=y
> CONFIG_X86_BIGSMP=y

Thank you all for the great linux kernel!

Jeff.

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Ingo Molnar]

* Jeff Chua <jeff.chua.linux@gmail.com> wrote:

> On Wed, Aug 6, 2008 at 2:42 PM, Jeff Chua <jeff.chua.linux@gmail.com> wrote:
> > On Wed, Aug 6, 2008 at 2:01 PM, Linus Torvalds
> > <torvalds@linux-foundation.org> wrote:
> >> One trivial thing to try would be to just bisect it. I assume 2.6.26 is
> > Bisecting now.
> 
> Thanks to all the great helpful suggestions from everyone, and this 
> turns out that I just need to enable the following switches, so I 
> didn't bisect further, and since it's first machine that I've tried 
> with more than 8 CPUs so I wasn't sure whether 2.6.16 has the same 
> problem, but if you wish, I could give 2.6.16 a try.
> 
> > CONFIG_X86_GENERICARCH=y
> > CONFIG_X86_BIGSMP=y
> 
> Thank you all for the great linux kernel!

i still consider a silent boot hang a bug we need to fix.

bigsmp might be required to have all cpus available on your box, but the 
kernel is still supposed to transparently fall back to less CPUs (and 
print a warning) if it cannot do that.

	Ingo

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Yinghai Lu]

On Mon, Aug 11, 2008 at 12:59 PM, Ingo Molnar <mingo@elte.hu> wrote:
>
> * Jeff Chua <jeff.chua.linux@gmail.com> wrote:
>
>> On Wed, Aug 6, 2008 at 2:42 PM, Jeff Chua <jeff.chua.linux@gmail.com> wrote:
>> > On Wed, Aug 6, 2008 at 2:01 PM, Linus Torvalds
>> > <torvalds@linux-foundation.org> wrote:
>> >> One trivial thing to try would be to just bisect it. I assume 2.6.26 is
>> > Bisecting now.
>>
>> Thanks to all the great helpful suggestions from everyone, and this
>> turns out that I just need to enable the following switches, so I
>> didn't bisect further, and since it's first machine that I've tried
>> with more than 8 CPUs so I wasn't sure whether 2.6.16 has the same
>> problem, but if you wish, I could give 2.6.16 a try.
>>
>> > CONFIG_X86_GENERICARCH=y
>> > CONFIG_X86_BIGSMP=y
>>
>> Thank you all for the great linux kernel!
>
> i still consider a silent boot hang a bug we need to fix.
>
> bigsmp might be required to have all cpus available on your box, but the
> kernel is still supposed to transparently fall back to less CPUs (and
> print a warning) if it cannot do that.
>
in setup.c::setup_arch() after go over with madt or mptable

#if defined(CONFIG_SMP) && defined(CONFIG_X86_PC) && defined(CONFIG_X86_32)
        if (def_to_bigsmp)
                printk(KERN_WARNING "More than 8 CPUs detected and "
                        "CONFIG_X86_PC cannot handle it.\nUse "
                        "CONFIG_X86_GENERICARCH or
CONFIG_X86_BIGSMP.\n"); ===> here need to change "or" to "and"
#endif

or just panic here? because screen scroll to pass it, and user will
not notice that...

YH

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Ingo Molnar]

* Yinghai Lu <yhlu.kernel@gmail.com> wrote:

> On Mon, Aug 11, 2008 at 12:59 PM, Ingo Molnar <mingo@elte.hu> wrote:
> >
> > * Jeff Chua <jeff.chua.linux@gmail.com> wrote:
> >
> >> On Wed, Aug 6, 2008 at 2:42 PM, Jeff Chua <jeff.chua.linux@gmail.com> wrote:
> >> > On Wed, Aug 6, 2008 at 2:01 PM, Linus Torvalds
> >> > <torvalds@linux-foundation.org> wrote:
> >> >> One trivial thing to try would be to just bisect it. I assume 2.6.26 is
> >> > Bisecting now.
> >>
> >> Thanks to all the great helpful suggestions from everyone, and this
> >> turns out that I just need to enable the following switches, so I
> >> didn't bisect further, and since it's first machine that I've tried
> >> with more than 8 CPUs so I wasn't sure whether 2.6.16 has the same
> >> problem, but if you wish, I could give 2.6.16 a try.
> >>
> >> > CONFIG_X86_GENERICARCH=y
> >> > CONFIG_X86_BIGSMP=y
> >>
> >> Thank you all for the great linux kernel!
> >
> > i still consider a silent boot hang a bug we need to fix.
> >
> > bigsmp might be required to have all cpus available on your box, but the
> > kernel is still supposed to transparently fall back to less CPUs (and
> > print a warning) if it cannot do that.
> >
> in setup.c::setup_arch() after go over with madt or mptable
> 
> #if defined(CONFIG_SMP) && defined(CONFIG_X86_PC) && defined(CONFIG_X86_32)
>         if (def_to_bigsmp)
>                 printk(KERN_WARNING "More than 8 CPUs detected and "
>                         "CONFIG_X86_PC cannot handle it.\nUse "
>                         "CONFIG_X86_GENERICARCH or
> CONFIG_X86_BIGSMP.\n"); ===> here need to change "or" to "and"
> #endif
> 
> or just panic here? because screen scroll to pass it, and user will
> not notice that...

a panic is better but still quite rude and doesnt give a user a system 
under which he can build an even greater kernel [after having discovered 
the warning in the syslog] ;-)

best would be to use as many CPUs as we can support, and skip the rest 
and boot up fine. (and print the warning prominently - the user does not 
make maximum use of available physical resources)

	Ingo

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Yinghai Lu]

On Mon, Aug 11, 2008 at 1:08 PM, Ingo Molnar <mingo@elte.hu> wrote:
>
> * Yinghai Lu <yhlu.kernel@gmail.com> wrote:
>
>> On Mon, Aug 11, 2008 at 12:59 PM, Ingo Molnar <mingo@elte.hu> wrote:
>> >
>> > * Jeff Chua <jeff.chua.linux@gmail.com> wrote:
>> >
>> >> On Wed, Aug 6, 2008 at 2:42 PM, Jeff Chua <jeff.chua.linux@gmail.com> wrote:
>> >> > On Wed, Aug 6, 2008 at 2:01 PM, Linus Torvalds
>> >> > <torvalds@linux-foundation.org> wrote:
>> >> >> One trivial thing to try would be to just bisect it. I assume 2.6.26 is
>> >> > Bisecting now.
>> >>
>> >> Thanks to all the great helpful suggestions from everyone, and this
>> >> turns out that I just need to enable the following switches, so I
>> >> didn't bisect further, and since it's first machine that I've tried
>> >> with more than 8 CPUs so I wasn't sure whether 2.6.16 has the same
>> >> problem, but if you wish, I could give 2.6.16 a try.
>> >>
>> >> > CONFIG_X86_GENERICARCH=y
>> >> > CONFIG_X86_BIGSMP=y
>> >>
>> >> Thank you all for the great linux kernel!
>> >
>> > i still consider a silent boot hang a bug we need to fix.
>> >
>> > bigsmp might be required to have all cpus available on your box, but the
>> > kernel is still supposed to transparently fall back to less CPUs (and
>> > print a warning) if it cannot do that.
>> >
>> in setup.c::setup_arch() after go over with madt or mptable
>>
>> #if defined(CONFIG_SMP) && defined(CONFIG_X86_PC) && defined(CONFIG_X86_32)
>>         if (def_to_bigsmp)
>>                 printk(KERN_WARNING "More than 8 CPUs detected and "
>>                         "CONFIG_X86_PC cannot handle it.\nUse "
>>                         "CONFIG_X86_GENERICARCH or
>> CONFIG_X86_BIGSMP.\n"); ===> here need to change "or" to "and"
>> #endif
>>
>> or just panic here? because screen scroll to pass it, and user will
>> not notice that...
>
> a panic is better but still quite rude and doesnt give a user a system
> under which he can build an even greater kernel [after having discovered
> the warning in the syslog] ;-)
>
> best would be to use as many CPUs as we can support, and skip the rest
> and boot up fine. (and print the warning prominently - the user does not
> make maximum use of available physical resources)

then  smp start AP cpu could check the apic id >=8 etc before try to
start it.in some cases

YH

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Yinghai Lu]

[-- Attachment #1: Type: text/plain, Size: 2480 bytes --]

On Mon, Aug 11, 2008 at 1:12 PM, Yinghai Lu <yhlu.kernel@gmail.com> wrote:
> On Mon, Aug 11, 2008 at 1:08 PM, Ingo Molnar <mingo@elte.hu> wrote:
>>
>> * Yinghai Lu <yhlu.kernel@gmail.com> wrote:
>>
>>> On Mon, Aug 11, 2008 at 12:59 PM, Ingo Molnar <mingo@elte.hu> wrote:
>>> >
>>> > * Jeff Chua <jeff.chua.linux@gmail.com> wrote:
>>> >
>>> >> On Wed, Aug 6, 2008 at 2:42 PM, Jeff Chua <jeff.chua.linux@gmail.com> wrote:
>>> >> > On Wed, Aug 6, 2008 at 2:01 PM, Linus Torvalds
>>> >> > <torvalds@linux-foundation.org> wrote:
>>> >> >> One trivial thing to try would be to just bisect it. I assume 2.6.26 is
>>> >> > Bisecting now.
>>> >>
>>> >> Thanks to all the great helpful suggestions from everyone, and this
>>> >> turns out that I just need to enable the following switches, so I
>>> >> didn't bisect further, and since it's first machine that I've tried
>>> >> with more than 8 CPUs so I wasn't sure whether 2.6.16 has the same
>>> >> problem, but if you wish, I could give 2.6.16 a try.
>>> >>
>>> >> > CONFIG_X86_GENERICARCH=y
>>> >> > CONFIG_X86_BIGSMP=y
>>> >>
>>> >> Thank you all for the great linux kernel!
>>> >
>>> > i still consider a silent boot hang a bug we need to fix.
>>> >
>>> > bigsmp might be required to have all cpus available on your box, but the
>>> > kernel is still supposed to transparently fall back to less CPUs (and
>>> > print a warning) if it cannot do that.
>>> >
>>> in setup.c::setup_arch() after go over with madt or mptable
>>>
>>> #if defined(CONFIG_SMP) && defined(CONFIG_X86_PC) && defined(CONFIG_X86_32)
>>>         if (def_to_bigsmp)
>>>                 printk(KERN_WARNING "More than 8 CPUs detected and "
>>>                         "CONFIG_X86_PC cannot handle it.\nUse "
>>>                         "CONFIG_X86_GENERICARCH or
>>> CONFIG_X86_BIGSMP.\n"); ===> here need to change "or" to "and"
>>> #endif
>>>
>>> or just panic here? because screen scroll to pass it, and user will
>>> not notice that...
>>
>> a panic is better but still quite rude and doesnt give a user a system
>> under which he can build an even greater kernel [after having discovered
>> the warning in the syslog] ;-)
>>
>> best would be to use as many CPUs as we can support, and skip the rest
>> and boot up fine. (and print the warning prominently - the user does not
>> make maximum use of available physical resources)
>
> then  smp start AP cpu could check the apic id >=8 etc before try to
> start it.in some cases

please check attach patches..

YH

[-- Warning: decoded text below may be mangled, UTF-8 assumed --]
[-- Attachment #2: def_big_smp.patch --]
[-- Type: text/x-patch; name=def_big_smp.patch, Size: 1399 bytes --]

[PATCH] x86: move def_to_bigsmp check later

and skil the apicid id > 8

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>

diff --git a/arch/x86/kernel/setup.c b/arch/x86/kernel/setup.c
index 6917779..59f07e1 100644
--- a/arch/x86/kernel/setup.c
+++ b/arch/x86/kernel/setup.c
@@ -863,12 +863,6 @@ void __init setup_arch(char **cmdline_p)
 	init_apic_mappings();
 	ioapic_init_mappings();
 
-#if defined(CONFIG_SMP) && defined(CONFIG_X86_PC) && defined(CONFIG_X86_32)
-	if (def_to_bigsmp)
-		printk(KERN_WARNING "More than 8 CPUs detected and "
-			"CONFIG_X86_PC cannot handle it.\nUse "
-			"CONFIG_X86_GENERICARCH or CONFIG_X86_BIGSMP.\n");
-#endif
 	kvm_guest_init();
 
 	e820_reserve_resources();
diff --git a/arch/x86/kernel/smpboot.c b/arch/x86/kernel/smpboot.c
index 21821f3..ce4ee3e 100644
--- a/arch/x86/kernel/smpboot.c
+++ b/arch/x86/kernel/smpboot.c
@@ -987,7 +987,17 @@ int __cpuinit native_cpu_up(unsigned int cpu)
 	flush_tlb_all();
 	low_mappings = 1;
 
+#ifdef CONFIG_X86_PC
+        if (def_to_bigsmp && apicid > 8) {
+                printk(KERN_WARNING "More than 8 CPUs detected and "
+                        "CONFIG_X86_PC cannot handle it.\nUse "
+                        "CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP.\n");
+		err = -1;
+	} else
+		err = do_boot_cpu(apicid, cpu);
+#else
 	err = do_boot_cpu(apicid, cpu);
+#endif
 
 	zap_low_mappings();
 	low_mappings = 0;

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Ingo Molnar]

* Yinghai Lu <yhlu.kernel@gmail.com> wrote:

> [PATCH] x86: move def_to_bigsmp check later
> 
> and skip the apicid id > 8

applied to tip/x86/urgent - thanks Yinghai. While we are touching this 
code i cleaned up the printk a bit: the line breaking was way too ugly, 
and the message not very informative about the effects of this problem. 
See the full commit below.

	Ingo

--------------->
>From b74548e76a0eab1f29546e7c5a589429c069a680 Mon Sep 17 00:00:00 2001
From: Yinghai Lu <yhlu.kernel@gmail.com>
Date: Mon, 11 Aug 2008 13:36:04 -0700
Subject: [PATCH] x86: fix 2.6.27rc1 cannot boot more than 8CPUs

Jeff Chua reported that booting a !bigsmp kernel on a 16-way box
hangs silently.

this is a long-standing issue, smp start AP cpu could check the
apic id >=8 etc before trying to start it.

achieve this by moving the def_to_bigsmp check later and skip the
apicid id > 8

[ mingo@elte.hu: clean up the message that is printed. ]

Reported-by: "Jeff Chua" <jeff.chua.linux@gmail.com>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

 arch/x86/kernel/setup.c   |    6 ------
 arch/x86/kernel/smpboot.c |   10 ++++++++++
 2 files changed, 10 insertions(+), 6 deletions(-)
---
 arch/x86/kernel/setup.c   |    6 ------
 arch/x86/kernel/smpboot.c |   10 ++++++++++
 2 files changed, 10 insertions(+), 6 deletions(-)

diff --git a/arch/x86/kernel/setup.c b/arch/x86/kernel/setup.c
index 6e5823b..68b48e3 100644
--- a/arch/x86/kernel/setup.c
+++ b/arch/x86/kernel/setup.c
@@ -861,12 +861,6 @@ void __init setup_arch(char **cmdline_p)
 	init_apic_mappings();
 	ioapic_init_mappings();
 
-#if defined(CONFIG_SMP) && defined(CONFIG_X86_PC) && defined(CONFIG_X86_32)
-	if (def_to_bigsmp)
-		printk(KERN_WARNING "More than 8 CPUs detected and "
-			"CONFIG_X86_PC cannot handle it.\nUse "
-			"CONFIG_X86_GENERICARCH or CONFIG_X86_BIGSMP.\n");
-#endif
 	kvm_guest_init();
 
 	e820_reserve_resources();
diff --git a/arch/x86/kernel/smpboot.c b/arch/x86/kernel/smpboot.c
index da10f07..91055d7 100644
--- a/arch/x86/kernel/smpboot.c
+++ b/arch/x86/kernel/smpboot.c
@@ -994,7 +994,17 @@ int __cpuinit native_cpu_up(unsigned int cpu)
 	flush_tlb_all();
 	low_mappings = 1;
 
+#ifdef CONFIG_X86_PC
+	if (def_to_bigsmp && apicid > 8) {
+		printk(KERN_WARNING
+			"More than 8 CPUs detected - skipping them.\n"
+			"Use CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP.\n");
+		err = -1;
+	} else
+		err = do_boot_cpu(apicid, cpu);
+#else
 	err = do_boot_cpu(apicid, cpu);
+#endif
 
 	zap_low_mappings();
 	low_mappings = 0;

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Jeff Chua]

On Wed, Aug 6, 2008 at 5:42 PM, Jeff Chua <jeff.chua.linux@gmail.com> 
wrote:
>>> CONFIG_X86_GENERICARCH=y
>>> CONFIG_X86_BIGSMP=y
>>> 8 more cpu need bigsmp mode.

> Just found it under " Subarchitecture Type (Generic architecture)",
> and then it shows the CONFIG_X86_BIGSMP option.

It works. Booted with 16CPUs. 32GB RAM.

CPU0 L7345 1.86GHz  0C
CPU1 L7345 1.86GHz  0C
CPU2 L7345 1.86GHz  0C
CPU3 L7345 1.86GHz  0C
CPU4 L7345 1.86GHz  0C
CPU5 L7345 1.86GHz  0C
CPU6 L7345 1.86GHz  0C
CPU7 L7345 1.86GHz  0C
CPU8 L7345 1.86GHz  0C
CPU9 L7345 1.86GHz  0C
CPU10 L7345 1.86GHz  0C
CPU11 L7345 1.86GHz  0C
CPU12 L7345 1.86GHz  0C
CPU13 L7345 1.86GHz  0C
CPU14 L7345 1.86GHz  0C
CPU15 L7345 1.86GHz  0C


So, but setting the config not obvious. And should CONFIG_X86_PC be 
considered as well as CONFIG_X86_GENERICARCH?

With CONFIG_X86_PC, I can set CONFIG_SPARSEMEM=y.

With CONFIG_X86_GENERICARCH, CONFIG_SPARSEMEM depends on CONFIG_NUMA.

I'm using the patch below to enable sparsemem instead of flatmem, but 
don't know what impact it has. System booted and running.

It would be nice to automatically default CONFIG_X86_BIGSMP with CPUs > 8. 
But I don't know to do that.


Thanks,
Jeff.


--- linux/arch/x86/Kconfig.org	2008-08-06 18:41:08 +0800
+++ linux/arch/x86/Kconfig	2008-08-06 18:48:13 +0800
@@ -1035,7 +1035,7 @@

   config ARCH_FLATMEM_ENABLE
   	def_bool y
-	depends on X86_32 && ARCH_SELECT_MEMORY_MODEL && X86_PC && !NUMA
+	depends on X86_32 && ARCH_SELECT_MEMORY_MODEL && !NUMA

   config ARCH_DISCONTIGMEM_ENABLE
   	def_bool y
@@ -1051,7 +1051,7 @@

   config ARCH_SPARSEMEM_ENABLE
   	def_bool y
-	depends on X86_64 || NUMA || (EXPERIMENTAL && X86_PC)
+	depends on X86_64 || NUMA || (EXPERIMENTAL && X86_PC) || X86_GENERICARCH
   	select SPARSEMEM_STATIC if X86_32
   	select SPARSEMEM_VMEMMAP_ENABLE if X86_64

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Yinghai Lu]

On Wed, Aug 6, 2008 at 4:09 AM, Jeff Chua <jeff.chua.linux@gmail.com> wrote:
>
> On Wed, Aug 6, 2008 at 5:42 PM, Jeff Chua <jeff.chua.linux@gmail.com> wrote:
>>>>
>>>> CONFIG_X86_GENERICARCH=y
>>>> CONFIG_X86_BIGSMP=y
>>>> 8 more cpu need bigsmp mode.
>
>> Just found it under " Subarchitecture Type (Generic architecture)",
>> and then it shows the CONFIG_X86_BIGSMP option.
>
> It works. Booted with 16CPUs. 32GB RAM.
>
> CPU0 L7345 1.86GHz  0C
> CPU1 L7345 1.86GHz  0C
> CPU2 L7345 1.86GHz  0C
> CPU3 L7345 1.86GHz  0C
> CPU4 L7345 1.86GHz  0C
> CPU5 L7345 1.86GHz  0C
> CPU6 L7345 1.86GHz  0C
> CPU7 L7345 1.86GHz  0C
> CPU8 L7345 1.86GHz  0C
> CPU9 L7345 1.86GHz  0C
> CPU10 L7345 1.86GHz  0C
> CPU11 L7345 1.86GHz  0C
> CPU12 L7345 1.86GHz  0C
> CPU13 L7345 1.86GHz  0C
> CPU14 L7345 1.86GHz  0C
> CPU15 L7345 1.86GHz  0C
>
>
> So, but setting the config not obvious. And should CONFIG_X86_PC be
> considered as well as CONFIG_X86_GENERICARCH?
>
> With CONFIG_X86_PC, I can set CONFIG_SPARSEMEM=y.
>
> With CONFIG_X86_GENERICARCH, CONFIG_SPARSEMEM depends on CONFIG_NUMA.
>
> I'm using the patch below to enable sparsemem instead of flatmem, but don't
> know what impact it has. System booted and running.
>
> It would be nice to automatically default CONFIG_X86_BIGSMP with CPUs > 8.
> But I don't know to do that.
>
>

actually x86_pc is one mode of genericarch..., genericarch already
could detect pc, bigsmp, and numaq, es7000, bigsmp, visew..

hope later we can change mach_default to default. but embed guys may
want to keep it as seperated one.

in the dmesg when booting x86_pc only, we already have warning to let
you set bigsmp if you have 8 more cpus.

YH

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Jeff Chua]

On Thu, Aug 7, 2008 at 12:13 AM, Yinghai Lu <yhlu.kernel@gmail.com> wrote:

> actually x86_pc is one mode of genericarch..., genericarch already
> could detect pc, bigsmp, and numaq, es7000, bigsmp, visew..

It seems to get "sparse mem", NUMA must be set first, but this is not
required for X86_PC.


> in the dmesg when booting x86_pc only, we already have warning to let
> you set bigsmp if you have 8 more cpus.

With more than 8 CPUs and upon boot up and hangs,  Shift+PgUp does not
work, so it's not possible to view console messages except those on
the current page, so I guess I missed that hint.

Jeff.

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Ingo Molnar]

* Jeff Chua <jeff.chua.linux@gmail.com> wrote:

>
> On Wed, Aug 6, 2008 at 5:42 PM, Jeff Chua <jeff.chua.linux@gmail.com>  
> wrote:
>>>> CONFIG_X86_GENERICARCH=y
>>>> CONFIG_X86_BIGSMP=y
>>>> 8 more cpu need bigsmp mode.
>
>> Just found it under " Subarchitecture Type (Generic architecture)",
>> and then it shows the CONFIG_X86_BIGSMP option.
>
> It works. Booted with 16CPUs. 32GB RAM.
>
> CPU0 L7345 1.86GHz  0C
> CPU1 L7345 1.86GHz  0C
> CPU2 L7345 1.86GHz  0C
> CPU3 L7345 1.86GHz  0C
> CPU4 L7345 1.86GHz  0C
> CPU5 L7345 1.86GHz  0C
> CPU6 L7345 1.86GHz  0C
> CPU7 L7345 1.86GHz  0C
> CPU8 L7345 1.86GHz  0C
> CPU9 L7345 1.86GHz  0C
> CPU10 L7345 1.86GHz  0C
> CPU11 L7345 1.86GHz  0C
> CPU12 L7345 1.86GHz  0C
> CPU13 L7345 1.86GHz  0C
> CPU14 L7345 1.86GHz  0C
> CPU15 L7345 1.86GHz  0C
>
>
> So, but setting the config not obvious. And should CONFIG_X86_PC be  
> considered as well as CONFIG_X86_GENERICARCH?
>
> With CONFIG_X86_PC, I can set CONFIG_SPARSEMEM=y.
>
> With CONFIG_X86_GENERICARCH, CONFIG_SPARSEMEM depends on CONFIG_NUMA.
>
> I'm using the patch below to enable sparsemem instead of flatmem, but  
> don't know what impact it has. System booted and running.
>
> It would be nice to automatically default CONFIG_X86_BIGSMP with CPUs 
> > 8. But I don't know to do that.

thanks, applied.

i'm wondering, does with that patch applied a working 2.6.26 .config if 
put through 'make oldconfig' boot fine on your box now? Any make 
oldconfig breakage is a regression we want to fix. We want upgrades 
between kernel versions to be seemless and complete.

	Ingo

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Ingo Molnar]

* Jeff Chua <jeff.chua.linux@gmail.com> wrote:

> On Wed, Aug 6, 2008 at 5:42 PM, Jeff Chua <jeff.chua.linux@gmail.com>  
> wrote:
>>>> CONFIG_X86_GENERICARCH=y
>>>> CONFIG_X86_BIGSMP=y
>>>> 8 more cpu need bigsmp mode.
>
>> Just found it under " Subarchitecture Type (Generic architecture)",
>> and then it shows the CONFIG_X86_BIGSMP option.
>
> It works. Booted with 16CPUs. 32GB RAM.

btw., could you please check that v2.6.27-rc3 (or later) kernels boot 
fine (with about 8 cpus) even if you hae genericarch/bigsmp disabled, 
and do not silently hang as it happened on your box before?

	Ingo

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Jeff Chua]

On Wed, Aug 13, 2008 at 10:16 PM, Ingo Molnar <mingo@elte.hu> wrote:

> btw., could you please check that v2.6.27-rc3 (or later) kernels boot
> fine (with about 8 cpus) even if you have genericarch/bigsmp disabled,
> and do not silently hang as it happened on your box before?

With 16 CPUs, it still hangs, but now the console is showing the
errors as intended.
... but it is supposed to hang?

More than 8 CPUs detected - skipping them.
Use CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP.
More than 8 CPUs detected - skipping them.
Use CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP.
More than 8 CPUs detected - skipping them.
Use CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP.
More than 8 CPUs detected - skipping them.
Use CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP.
Booting processor 8/1 ip 6000
Initializing CPU#8
Calibrating delay using timer specific routine.. 3723.88 BogoMIPS (lpj=7447763)
CPU: L1 I cache: 32Kb, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU8: Intel(8) Xeon(R) CPU        L7345  @ 1.86GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#8]: passed.
*** HANGS HERE ***

Thanks,
Jeff.

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Jeff Chua]

On Thu, Aug 14, 2008 at 1:10 AM, Jeff Chua <jeff.chua.linux@gmail.com> wrote:
> On Wed, Aug 13, 2008 at 10:16 PM, Ingo Molnar <mingo@elte.hu> wrote:
>
>> btw., could you please check that v2.6.27-rc3 (or later) kernels boot
>> fine (with about 8 cpus) even if you have genericarch/bigsmp disabled,
>> and do not silently hang as it happened on your box before?
>
> With 16 CPUs, it still hangs, but now the console is showing the
> errors as intended.
> ... but it is supposed to hang?

I tried with just CONFIG_NR_CPUS=8 and this time it booted, but stange
thing is I only see 2 CPUs! To be more precise, it's without both
CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP.

And when I tried to enable the CPUs, it complained about:

# cat cpu6/online
0
# echo 1 > cpu6/online
More than 8 CPUs detected - skipping them.
Use CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP.
-bash: echo: write error: Input/output error

Prior to the patch, the system booted with all 8 CPUs.

Again, if I enable both CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP,
I get all 16 CPUs.

Thanks,
Jeff.

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Ingo Molnar]

* Jeff Chua <jeff.chua.linux@gmail.com> wrote:

> On Thu, Aug 14, 2008 at 1:10 AM, Jeff Chua <jeff.chua.linux@gmail.com> wrote:
> > On Wed, Aug 13, 2008 at 10:16 PM, Ingo Molnar <mingo@elte.hu> wrote:
> >
> >> btw., could you please check that v2.6.27-rc3 (or later) kernels boot
> >> fine (with about 8 cpus) even if you have genericarch/bigsmp disabled,
> >> and do not silently hang as it happened on your box before?
> >
> > With 16 CPUs, it still hangs, but now the console is showing the
> > errors as intended.
> > ... but it is supposed to hang?
> 
> I tried with just CONFIG_NR_CPUS=8 and this time it booted, but stange
> thing is I only see 2 CPUs! To be more precise, it's without both
> CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP.
> 
> And when I tried to enable the CPUs, it complained about:
> 
> # cat cpu6/online
> 0
> # echo 1 > cpu6/online
> More than 8 CPUs detected - skipping them.
> Use CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP.
> -bash: echo: write error: Input/output error
> 
> Prior to the patch, the system booted with all 8 CPUs.
> 
> Again, if I enable both CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP,
> I get all 16 CPUs.

Yinghai, could the APIC ID enumeration be nonsequential and we skip CPUs 
starting at the third one already? I think we should accept all CPUs 
that are within our support range.

	Ingo

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Yinghai Lu]

On Wed, Aug 13, 2008 at 10:39 AM, Ingo Molnar <mingo@elte.hu> wrote:
>
> * Jeff Chua <jeff.chua.linux@gmail.com> wrote:
>
>> On Thu, Aug 14, 2008 at 1:10 AM, Jeff Chua <jeff.chua.linux@gmail.com> wrote:
>> > On Wed, Aug 13, 2008 at 10:16 PM, Ingo Molnar <mingo@elte.hu> wrote:
>> >
>> >> btw., could you please check that v2.6.27-rc3 (or later) kernels boot
>> >> fine (with about 8 cpus) even if you have genericarch/bigsmp disabled,
>> >> and do not silently hang as it happened on your box before?
>> >
>> > With 16 CPUs, it still hangs, but now the console is showing the
>> > errors as intended.
>> > ... but it is supposed to hang?
>>
>> I tried with just CONFIG_NR_CPUS=8 and this time it booted, but stange
>> thing is I only see 2 CPUs! To be more precise, it's without both
>> CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP.
>>
>> And when I tried to enable the CPUs, it complained about:
>>
>> # cat cpu6/online
>> 0
>> # echo 1 > cpu6/online
>> More than 8 CPUs detected - skipping them.
>> Use CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP.
>> -bash: echo: write error: Input/output error
>>
>> Prior to the patch, the system booted with all 8 CPUs.

that is new regression...

>>
>> Again, if I enable both CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP,
>> I get all 16 CPUs.
>
> Yinghai, could the APIC ID enumeration be nonsequential and we skip CPUs
> starting at the third one already? I think we should accept all CPUs
> that are within our support range.

will try to clear those bits on smp_sanity_check...

YH

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Yinghai Lu]

[-- Attachment #1: Type: text/plain, Size: 1393 bytes --]

On Wed, Aug 13, 2008 at 10:46 AM, Yinghai Lu <yhlu.kernel@gmail.com> wrote:
> On Wed, Aug 13, 2008 at 10:39 AM, Ingo Molnar <mingo@elte.hu> wrote:
>>
>> * Jeff Chua <jeff.chua.linux@gmail.com> wrote:
>>
>>> On Thu, Aug 14, 2008 at 1:10 AM, Jeff Chua <jeff.chua.linux@gmail.com> wrote:
>>> > On Wed, Aug 13, 2008 at 10:16 PM, Ingo Molnar <mingo@elte.hu> wrote:
>>> >
>>> >> btw., could you please check that v2.6.27-rc3 (or later) kernels boot
>>> >> fine (with about 8 cpus) even if you have genericarch/bigsmp disabled,
>>> >> and do not silently hang as it happened on your box before?
>>> >
>>> > With 16 CPUs, it still hangs, but now the console is showing the
>>> > errors as intended.
>>> > ... but it is supposed to hang?
>>>
>>> I tried with just CONFIG_NR_CPUS=8 and this time it booted, but stange
>>> thing is I only see 2 CPUs! To be more precise, it's without both
>>> CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP.
>>>
>>> And when I tried to enable the CPUs, it complained about:
>>>
>>> # cat cpu6/online
>>> 0
>>> # echo 1 > cpu6/online
>>> More than 8 CPUs detected - skipping them.
>>> Use CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP.
>>> -bash: echo: write error: Input/output error
>>>
>>> Prior to the patch, the system booted with all 8 CPUs.
>
> that is new regression...

jeff,

please check the attached patch. it should fix the new regression and
will not hang.

YH

[-- Warning: decoded text below may be mangled, UTF-8 assumed --]
[-- Attachment #2: big_smp_check.patch --]
[-- Type: text/x-patch; name=big_smp_check.patch, Size: 1839 bytes --]

[PATCH] x86: check bigsmp in smp_sanity_check instead of cpu_up

clear bits for cpu nr > 8

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>

---
 arch/x86/kernel/smpboot.c |   38 ++++++++++++++++++++++++++++----------
 1 file changed, 28 insertions(+), 10 deletions(-)

Index: linux-2.6/arch/x86/kernel/smpboot.c
===================================================================
--- linux-2.6.orig/arch/x86/kernel/smpboot.c
+++ linux-2.6/arch/x86/kernel/smpboot.c
@@ -987,17 +987,7 @@ int __cpuinit native_cpu_up(unsigned int
 	flush_tlb_all();
 	low_mappings = 1;
 
-#ifdef CONFIG_X86_PC
-	if (def_to_bigsmp && apicid > 8) {
-		printk(KERN_WARNING
-			"More than 8 CPUs detected - skipping them.\n"
-			"Use CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP.\n");
-		err = -1;
-	} else
-		err = do_boot_cpu(apicid, cpu);
-#else
 	err = do_boot_cpu(apicid, cpu);
-#endif
 
 	zap_low_mappings();
 	low_mappings = 0;
@@ -1051,6 +1041,34 @@ static __init void disable_smp(void)
 static int __init smp_sanity_check(unsigned max_cpus)
 {
 	preempt_disable();
+
+#if defined(CONFIG_X86_PC) && defined(CONFIG_X86_32)
+        if (def_to_bigsmp && nr_cpu_ids > 8) {
+		unsigned int cpu;
+		unsigned nr;
+
+                printk(KERN_WARNING
+                        "More than 8 CPUs detected - skipping them.\n"
+                        "Use CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP.\n");
+
+		nr = 0;
+		for_each_present_cpu(cpu) {
+			if (nr >= 8)
+				cpu_clear(cpu, cpu_present_map);
+			nr++;
+		}
+
+		nr = 0;
+		for_each_possible_cpu(cpu) {
+			if (nr >= 8)
+				cpu_clear(cpu, cpu_possible_map);
+			nr++;
+		}
+
+		nr_cpu_ids = 8;
+        }
+#endif
+
 	if (!physid_isset(hard_smp_processor_id(), phys_cpu_present_map)) {
 		printk(KERN_WARNING "weird, boot CPU (#%d) not listed"
 				    "by the BIOS.\n", hard_smp_processor_id());

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Jeff Chua]

On Thu, Aug 14, 2008 at 2:33 AM, Yinghai Lu <yhlu.kernel@gmail.com> wrote:

>>>> > With 16 CPUs, it still hangs, but now the console is showing the
>>>> > errors as intended.
>>>> > ... but it is supposed to hang?

> please check the attached patch. it should fix the new regression and
> will not hang.

Ok, booted up and not hanged, but those messages below don't show up
anywhere. I've tested with CONFIG_NR_CPUS=16 and 8 as well. Just got 8
cpus

More than 8 CPUs detected - skipping them.
Use CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP.

# cat /sys/devices/system/cpu/possible
0-7

CONFIG_X86_32=y
CONFIG_X86_PC=y


Looks like it's not going into this condition
+        if (def_to_bigsmp && nr_cpu_ids > 8) {


Shall this be put back so that it'll show the message?
-       if (def_to_bigsmp && apicid > 8) {
-               printk(KERN_WARNING
-                       "More than 8 CPUs detected - skipping them.\n"
-                       "Use CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP.\n");
-       }


Thanks,
Jeff.

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Yinghai Lu]

On Thu, Aug 14, 2008 at 12:16 AM, Jeff Chua <jeff.chua.linux@gmail.com> wrote:
> On Thu, Aug 14, 2008 at 2:33 AM, Yinghai Lu <yhlu.kernel@gmail.com> wrote:
>
>>>>> > With 16 CPUs, it still hangs, but now the console is showing the
>>>>> > errors as intended.
>>>>> > ... but it is supposed to hang?
>
>> please check the attached patch. it should fix the new regression and
>> will not hang.
>
> Ok, booted up and not hanged, but those messages below don't show up
> anywhere. I've tested with CONFIG_NR_CPUS=16 and 8 as well. Just got 8
> cpus
>
> More than 8 CPUs detected - skipping them.
> Use CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP.
>
> # cat /sys/devices/system/cpu/possible
> 0-7
>
> CONFIG_X86_32=y
> CONFIG_X86_PC=y
>
>

double checked on one 16 cores system got

CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 0(4) -> Core 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
using C1E aware idle routine
Checking 'hlt' instruction... OK.
ACPI: Core revision 20080609
Parsing all Control Methods:
Table [DSDT](id 0001) - 1289 Objects with 114 Devices 462 Methods 26 Regions
Parsing all Control Methods:
Table [SSDT](id 0002) - 80 Objects with 0 Devices 0 Methods 0 Regions
 tbxface-0596 [00] tb_load_namespace     : ACPI Tables successfully acquired
evxfevnt-0091 [00] enable                : Transition to ACPI mode successful
More than 8 CPUs detected - skipping them.
Use CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP.
enabled ExtINT on CPU#0

YH

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Ingo Molnar]

* Jeff Chua <jeff.chua.linux@gmail.com> wrote:

> On Thu, Aug 14, 2008 at 2:33 AM, Yinghai Lu <yhlu.kernel@gmail.com> wrote:
> 
> >>>> > With 16 CPUs, it still hangs, but now the console is showing the
> >>>> > errors as intended.
> >>>> > ... but it is supposed to hang?
> 
> > please check the attached patch. it should fix the new regression and
> > will not hang.
> 
> Ok, booted up and not hanged, but those messages below don't show up
> anywhere. I've tested with CONFIG_NR_CPUS=16 and 8 as well. Just got 8
> cpus
> 
> More than 8 CPUs detected - skipping them.
> Use CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP.
> 
> # cat /sys/devices/system/cpu/possible
> 0-7
> 
> CONFIG_X86_32=y
> CONFIG_X86_PC=y
> 
> 
> Looks like it's not going into this condition
> +        if (def_to_bigsmp && nr_cpu_ids > 8) {
> 
> 
> Shall this be put back so that it'll show the message?
> -       if (def_to_bigsmp && apicid > 8) {
> -               printk(KERN_WARNING
> -                       "More than 8 CPUs detected - skipping them.\n"
> -                       "Use CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP.\n");
> -       }

could you post the full dmesg? And the modified patch that you've tested 
to both have 8 CPUs without bigsmp and which also shows the printk?

	Ingo

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Jeff Chua]

[-- Attachment #1: Type: TEXT/PLAIN, Size: 2508 bytes --]



On Thu, Aug 14, 2008 at 5:07 PM, Ingo Molnar <mingo@elte.hu> wrote:
>
> * Jeff Chua <jeff.chua.linux@gmail.com> wrote:
>
>> On Thu, Aug 14, 2008 at 2:33 AM, Yinghai Lu <yhlu.kernel@gmail.com> 
wrote:
>>
>> >>>> > With 16 CPUs, it still hangs, but now the console is showing the
>> >>>> > errors as intended.
>> >>>> > ... but it is supposed to hang?
>>
>> > please check the attached patch. it should fix the new regression and
>> > will not hang.
>>
>> Ok, booted up and not hanged, but those messages below don't show up
>> anywhere. I've tested with CONFIG_NR_CPUS=16 and 8 as well. Just got 8
>> cpus
>>
>> More than 8 CPUs detected - skipping them.
>> Use CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP.
>>
>> # cat /sys/devices/system/cpu/possible
>> 0-7
>>
>> CONFIG_X86_32=y
>> CONFIG_X86_PC=y
>>
>>
>> Looks like it's not going into this condition
>> +        if (def_to_bigsmp && nr_cpu_ids > 8) {
>>
>>
>> Shall this be put back so that it'll show the message?
>> -       if (def_to_bigsmp && apicid > 8) {
>> -               printk(KERN_WARNING
>> -                       "More than 8 CPUs detected - skipping them.\n"
>> -                       "Use CONFIG_X86_GENERICARCH and 
CONFIG_X86_BIGSMP.\n");
>> -       }
>
> could you post the full dmesg? And the modified patch that you've tested
> to both have 8 CPUs without bigsmp and which also shows the printk?
>
>        Ingo
>

Attached. cpu.8
    CONFIG_X86_32=y
    CONFIG_X86_PC=y
    CONFIG_X86=y
    CONFIG_NR_CPUS=8

Attached. cpu.16
    CONFIG_X86_32=y
    CONFIG_X86_PC=y
    CONFIG_X86=y
    CONFIG_NR_CPUS=16

Attached cpu.16.big
    CONFIG_X86_32=y
    CONFIG_X86=y
    CONFIG_X86_GENERICARCH=y
    CONFIG_X86_BIGSMP=y
    # CONFIG_X86_PC is not set
    CONFIG_NR_CPUS=16

Attached cpu.16.nobig (same as cpu.16 except with modifed patch)
    CONFIG_X86_32=y
    CONFIG_X86_PC=y
    CONFIG_X86=y
    CONFIG_NR_CPUS=16

Attached is the modified patch to make the warning appears. It's Yinghai's 
patch modified to just display the error and continue to boot.


Thanks,
Jeff

--- linux.16/arch/x86/kernel/smpboot.c.org	2008-08-15 18:15:37 +0800
+++ linux.16/arch/x86/kernel/smpboot.c	2008-08-15 18:13:42 +0800
@@ -999,9 +999,12 @@
  		printk(KERN_WARNING
  			"More than 8 CPUs detected - skipping them.\n"
  			"Use CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP.\n");
-	}
-#endif
+		err = -1;
+	} else
+		err = do_boot_cpu(apicid, cpu);
+#else
  	err = do_boot_cpu(apicid, cpu);
+#endif

  	zap_low_mappings();
  	low_mappings = 0;



[-- Attachment #2: Type: TEXT/PLAIN, Size: 31509 bytes --]

096K
CPU: Physical Processor ID: 4
CPU: Processor Core ID: 0
CPU2: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#2]: passed.
CPU 3 irqstacks, hard=c0520000 soft=c0518000
Booting processor 3/24 ip 6000
Initializing CPU#3
Calibrating delay using timer specific routine.. 3723.90 BogoMIPS (lpj=7447814)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 6
CPU: Processor Core ID: 0
CPU3: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#3]: passed.
CPU 4 irqstacks, hard=c0521000 soft=c0519000
Booting processor 4/2 ip 6000
Initializing CPU#4
Calibrating delay using timer specific routine.. 3723.87 BogoMIPS (lpj=7447757)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 2
CPU4: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#4]: passed.
CPU 5 irqstacks, hard=c0522000 soft=c051a000
Booting processor 5/10 ip 6000
Initializing CPU#5
Calibrating delay using timer specific routine.. 3723.89 BogoMIPS (lpj=7447799)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 2
CPU5: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#5]: passed.
CPU 6 irqstacks, hard=c0523000 soft=c051b000
Booting processor 6/18 ip 6000
Initializing CPU#6
Calibrating delay using timer specific routine.. 3723.89 BogoMIPS (lpj=7447794)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 4
CPU: Processor Core ID: 2
CPU6: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#6]: passed.
CPU 7 irqstacks, hard=c0524000 soft=c051c000
Booting processor 7/26 ip 6000
Initializing CPU#7
Calibrating delay using timer specific routine.. 3723.89 BogoMIPS (lpj=7447796)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 6
CPU: Processor Core ID: 2
CPU7: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#7]: passed.
Brought up 8 CPUs
Total of 8 processors activated (29791.10 BogoMIPS).
net_namespace: 596 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
No dock devices found.
ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
ACPI: bus type pci registered
PCI: Using configuration type 1 for base access
PCI: Dell PowerEdge R900 detected, enabling pci=bfsort.
ACPI: EC: Look up EC in DSDT
ACPI: BIOS _OSI(Linux) query ignored
ACPI: DMI System Vendor: Dell Inc.
ACPI: DMI Product Name: PowerEdge R900
ACPI: DMI Product Version: 
ACPI: DMI Board Name: 0C764H
ACPI: DMI BIOS Vendor: Dell Inc.
ACPI: DMI BIOS Date: 03/23/2008
ACPI: Please send DMI info above to linux-acpi@vger.kernel.org
ACPI: If "acpi_osi=Linux" works better, please notify linux-acpi@vger.kernel.org
ACPI: Interpreter enabled
ACPI: (supports S0 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
pci 0000:00:00.0: PME# disabled
pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
pci 0000:00:01.0: PME# disabled
pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
pci 0000:00:02.0: PME# disabled
pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
pci 0000:00:03.0: PME# disabled
pci 0000:00:04.0: PME# supported from D0 D3hot D3cold
pci 0000:00:04.0: PME# disabled
pci 0000:00:06.0: PME# supported from D0 D3hot D3cold
pci 0000:00:06.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:16:00.0: PME# supported from D0 D3hot D3cold
pci 0000:16:00.0: PME# disabled
pci 0000:16:00.3: PME# supported from D0 D3hot D3cold
pci 0000:16:00.3: PME# disabled
pci 0000:17:00.0: PME# supported from D0 D3hot D3cold
pci 0000:17:00.0: PME# disabled
pci 0000:17:01.0: PME# supported from D0 D3hot D3cold
pci 0000:17:01.0: PME# disabled
pci 0000:19:00.0: supports D1
pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
pci 0000:01:00.0: PME# disabled
pci 0000:02:01.0: PME# supported from D0 D3hot D3cold
pci 0000:02:01.0: PME# disabled
pci 0000:02:02.0: PME# supported from D0 D3hot D3cold
pci 0000:02:02.0: PME# disabled
pci 0000:02:03.0: PME# supported from D0 D3hot D3cold
pci 0000:02:03.0: PME# disabled
pci 0000:02:04.0: PME# supported from D0 D3hot D3cold
pci 0000:02:04.0: PME# disabled
pci 0000:02:05.0: PME# supported from D0 D3hot D3cold
pci 0000:02:05.0: PME# disabled
pci 0000:0a:00.0: PME# supported from D0 D3hot D3cold
pci 0000:0a:00.0: PME# disabled
pci 0000:0b:00.0: PME# supported from D3hot D3cold
pci 0000:0b:00.0: PME# disabled
pci 0000:08:00.0: PME# supported from D0 D3hot D3cold
pci 0000:08:00.0: PME# disabled
pci 0000:09:00.0: PME# supported from D3hot D3cold
pci 0000:09:00.0: PME# disabled
pci 0000:06:00.0: PME# supported from D0 D3hot D3cold
pci 0000:06:00.0: PME# disabled
pci 0000:07:00.0: PME# supported from D3hot D3cold
pci 0000:07:00.0: PME# disabled
pci 0000:04:00.0: PME# supported from D0 D3hot D3cold
pci 0000:04:00.0: PME# disabled
pci 0000:05:00.0: PME# supported from D3hot D3cold
pci 0000:05:00.0: PME# disabled
pci 0000:0c:00.0: PME# supported from D0 D3hot D3cold
pci 0000:0c:00.0: PME# disabled
pci 0000:0d:02.0: PME# supported from D0 D3hot D3cold
pci 0000:0d:02.0: PME# disabled
pci 0000:0d:04.0: PME# supported from D0 D3hot D3cold
pci 0000:0d:04.0: PME# disabled
pci 0000:10:00.0: PME# supported from D0 D3hot D3cold
pci 0000:10:00.0: PME# disabled
pci 0000:11:02.0: PME# supported from D0 D3hot D3cold
pci 0000:11:02.0: PME# disabled
pci 0000:11:04.0: PME# supported from D0 D3hot D3cold
pci 0000:11:04.0: PME# disabled
pci 0000:1b:0c.0: supports D1
pci 0000:1b:0c.0: supports D2
pci 0000:00:1e.0: transparent bridge
bus 00 -> node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2.UPST._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2.UPST.DWN1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2.UPST.DWN2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3.UPST.DWN2.BCOM._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3.UPST.DWN3.BCOM._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3.UPST.DWN4.BCOM._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3.UPST.DWN5.BCOM._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4.UPST.DWNB._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4.UPST.DWNC._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX6.UPST.DWNB._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX6.UPST.DWNC._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.SBEX._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.COMP._PRT]
ACPI: PCI Interrupt Link [LK00] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LK01] (IRQs 3 4 5 6 7 *10 11 12)
ACPI: PCI Interrupt Link [LK02] (IRQs 3 4 5 *6 7 10 11 12)
ACPI: PCI Interrupt Link [LK03] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LK04] (IRQs 3 4 *5 6 7 10 11 12)
ACPI: PCI Interrupt Link [LK05] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LK06] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LK07] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
Switched to high resolution mode on CPU 0
Switched to high resolution mode on CPU 5
Switched to high resolution mode on CPU 4
Switched to high resolution mode on CPU 3
Switched to high resolution mode on CPU 2
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 7
Switched to high resolution mode on CPU 6
system 00:07: ioport range 0x800-0x87f has been reserved
system 00:07: ioport range 0x880-0x8bf has been reserved
system 00:07: ioport range 0x8c0-0x8df has been reserved
system 00:07: ioport range 0x8e0-0x8e3 has been reserved
system 00:07: ioport range 0x8f0-0x8f1 has been reserved
system 00:07: ioport range 0x900-0x900 has been reserved
system 00:07: ioport range 0xc00-0xc7f has been reserved
system 00:07: ioport range 0xca0-0xca7 has been reserved
system 00:07: ioport range 0xca9-0xcab has been reserved
system 00:07: ioport range 0xcad-0xcaf has been reserved
system 00:08: ioport range 0xca8-0xca8 has been reserved
system 00:08: ioport range 0xcac-0xcac has been reserved
system 00:09: iomem range 0xe0000000-0xefffffff could not be reserved
pci 0000:00:01.0: PCI bridge, secondary bus 0000:14
pci 0000:00:01.0:   IO window: disabled
pci 0000:00:01.0:   MEM window: disabled
pci 0000:00:01.0:   PREFETCH window: disabled
pci 0000:17:00.0: PCI bridge, secondary bus 0000:19
pci 0000:17:00.0:   IO window: 0xe000-0xefff
pci 0000:17:00.0:   MEM window: 0xde200000-0xde3fffff
pci 0000:17:00.0:   PREFETCH window: disabled
pci 0000:17:01.0: PCI bridge, secondary bus 0000:18
pci 0000:17:01.0:   IO window: disabled
pci 0000:17:01.0:   MEM window: disabled
pci 0000:17:01.0:   PREFETCH window: disabled
pci 0000:16:00.0: PCI bridge, secondary bus 0000:17
pci 0000:16:00.0:   IO window: 0xe000-0xefff
pci 0000:16:00.0:   MEM window: 0xde200000-0xde3fffff
pci 0000:16:00.0:   PREFETCH window: disabled
pci 0000:16:00.3: PCI bridge, secondary bus 0000:1a
pci 0000:16:00.3:   IO window: disabled
pci 0000:16:00.3:   MEM window: disabled
pci 0000:16:00.3:   PREFETCH window: disabled
pci 0000:00:02.0: PCI bridge, secondary bus 0000:16
pci 0000:00:02.0:   IO window: 0xe000-0xefff
pci 0000:00:02.0:   MEM window: 0xde100000-0xde3fffff
pci 0000:00:02.0:   PREFETCH window: disabled
pci 0000:02:01.0: PCI bridge, secondary bus 0000:03
pci 0000:02:01.0:   IO window: disabled
pci 0000:02:01.0:   MEM window: disabled
pci 0000:02:01.0:   PREFETCH window: disabled
pci 0000:0a:00.0: PCI bridge, secondary bus 0000:0b
pci 0000:0a:00.0:   IO window: disabled
pci 0000:0a:00.0:   MEM window: 0xd6000000-0xd7ffffff
pci 0000:0a:00.0:   PREFETCH window: disabled
pci 0000:02:02.0: PCI bridge, secondary bus 0000:0a
pci 0000:02:02.0:   IO window: disabled
pci 0000:02:02.0:   MEM window: 0xd6000000-0xd7ffffff
pci 0000:02:02.0:   PREFETCH window: disabled
pci 0000:08:00.0: PCI bridge, secondary bus 0000:09
pci 0000:08:00.0:   IO window: disabled
pci 0000:08:00.0:   MEM window: 0xd8000000-0xd9ffffff
pci 0000:08:00.0:   PREFETCH window: disabled
pci 0000:02:03.0: PCI bridge, secondary bus 0000:08
pci 0000:02:03.0:   IO window: disabled
pci 0000:02:03.0:   MEM window: 0xd8000000-0xd9ffffff
pci 0000:02:03.0:   PREFETCH window: disabled
pci 0000:06:00.0: PCI bridge, secondary bus 0000:07
pci 0000:06:00.0:   IO window: disabled
pci 0000:06:00.0:   MEM window: 0xda000000-0xdbffffff
pci 0000:06:00.0:   PREFETCH window: disabled
pci 0000:02:04.0: PCI bridge, secondary bus 0000:06
pci 0000:02:04.0:   IO window: disabled
pci 0000:02:04.0:   MEM window: 0xda000000-0xdbffffff
pci 0000:02:04.0:   PREFETCH window: disabled
pci 0000:04:00.0: PCI bridge, secondary bus 0000:05
pci 0000:04:00.0:   IO window: disabled
pci 0000:04:00.0:   MEM window: 0xdc000000-0xddffffff
pci 0000:04:00.0:   PREFETCH window: disabled
pci 0000:02:05.0: PCI bridge, secondary bus 0000:04
pci 0000:02:05.0:   IO window: disabled
pci 0000:02:05.0:   MEM window: 0xdc000000-0xddffffff
pci 0000:02:05.0:   PREFETCH window: disabled
pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
pci 0000:01:00.0:   IO window: disabled
pci 0000:01:00.0:   MEM window: 0xd6000000-0xddffffff
pci 0000:01:00.0:   PREFETCH window: disabled
pci 0000:00:03.0: PCI bridge, secondary bus 0000:01
pci 0000:00:03.0:   IO window: disabled
pci 0000:00:03.0:   MEM window: 0xd6000000-0xddffffff
pci 0000:00:03.0:   PREFETCH window: disabled
pci 0000:0d:02.0: PCI bridge, secondary bus 0000:0f
pci 0000:0d:02.0:   IO window: disabled
pci 0000:0d:02.0:   MEM window: disabled
pci 0000:0d:02.0:   PREFETCH window: disabled
pci 0000:0d:04.0: PCI bridge, secondary bus 0000:0e
pci 0000:0d:04.0:   IO window: disabled
pci 0000:0d:04.0:   MEM window: disabled
pci 0000:0d:04.0:   PREFETCH window: disabled
pci 0000:0c:00.0: PCI bridge, secondary bus 0000:0d
pci 0000:0c:00.0:   IO window: disabled
pci 0000:0c:00.0:   MEM window: disabled
pci 0000:0c:00.0:   PREFETCH window: disabled
pci 0000:00:04.0: PCI bridge, secondary bus 0000:0c
pci 0000:00:04.0:   IO window: disabled
pci 0000:00:04.0:   MEM window: disabled
pci 0000:00:04.0:   PREFETCH window: disabled
pci 0000:11:02.0: PCI bridge, secondary bus 0000:13
pci 0000:11:02.0:   IO window: disabled
pci 0000:11:02.0:   MEM window: disabled
pci 0000:11:02.0:   PREFETCH window: disabled
pci 0000:11:04.0: PCI bridge, secondary bus 0000:12
pci 0000:11:04.0:   IO window: disabled
pci 0000:11:04.0:   MEM window: disabled
pci 0000:11:04.0:   PREFETCH window: disabled
pci 0000:10:00.0: PCI bridge, secondary bus 0000:11
pci 0000:10:00.0:   IO window: disabled
pci 0000:10:00.0:   MEM window: disabled
pci 0000:10:00.0:   PREFETCH window: disabled
pci 0000:00:06.0: PCI bridge, secondary bus 0000:10
pci 0000:00:06.0:   IO window: disabled
pci 0000:00:06.0:   MEM window: disabled
pci 0000:00:06.0:   PREFETCH window: disabled
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:15
pci 0000:00:1c.0:   IO window: disabled
pci 0000:00:1c.0:   MEM window: disabled
pci 0000:00:1c.0:   PREFETCH window: disabled
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:1b
pci 0000:00:1e.0:   IO window: 0xd000-0xdfff
pci 0000:00:1e.0:   MEM window: 0xde400000-0xde4fffff
pci 0000:00:1e.0:   PREFETCH window: 0x000000c8000000-0x000000cfffffff
pci 0000:00:01.0: PCI INT A -> GSI 36 (level, low) -> IRQ 36
pci 0000:00:01.0: setting latency timer to 64
pci 0000:00:02.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:02.0: setting latency timer to 64
pci 0000:16:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:16:00.0: setting latency timer to 64
pci 0000:17:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:17:00.0: setting latency timer to 64
pci 0000:17:01.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
pci 0000:17:01.0: setting latency timer to 64
pci 0000:16:00.3: setting latency timer to 64
pci 0000:00:03.0: PCI INT A -> GSI 37 (level, low) -> IRQ 37
pci 0000:00:03.0: setting latency timer to 64
pci 0000:01:00.0: setting latency timer to 64
pci 0000:02:01.0: setting latency timer to 64
pci 0000:02:02.0: setting latency timer to 64
pci 0000:0a:00.0: setting latency timer to 64
pci 0000:02:03.0: setting latency timer to 64
pci 0000:08:00.0: setting latency timer to 64
pci 0000:02:04.0: setting latency timer to 64
pci 0000:06:00.0: setting latency timer to 64
pci 0000:02:05.0: setting latency timer to 64
pci 0000:04:00.0: setting latency timer to 64
pci 0000:00:04.0: PCI INT A -> GSI 32 (level, low) -> IRQ 32
pci 0000:00:04.0: setting latency timer to 64
pci 0000:0c:00.0: setting latency timer to 64
pci 0000:0d:02.0: setting latency timer to 64
pci 0000:0d:04.0: setting latency timer to 64
pci 0000:00:06.0: PCI INT A -> GSI 33 (level, low) -> IRQ 33
pci 0000:00:06.0: setting latency timer to 64
pci 0000:10:00.0: setting latency timer to 64
pci 0000:11:02.0: setting latency timer to 64
pci 0000:11:04.0: setting latency timer to 64
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
highmem bounce pool size: 64 pages
HugeTLB registered 2 MB page size, pre-allocated 0 pages
msgmni has been set to 1236
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered (default)
pci 0000:1b:0c.0: Boot video device
pcieport-driver 0000:00:01.0: setting latency timer to 64
pcieport-driver 0000:00:01.0: found MSI capability
pci_express 0000:00:01.0:pcie00: allocate port service
pcieport-driver 0000:00:02.0: setting latency timer to 64
pcieport-driver 0000:00:02.0: found MSI capability
pci_express 0000:00:02.0:pcie00: allocate port service
pcieport-driver 0000:00:03.0: setting latency timer to 64
pcieport-driver 0000:00:03.0: found MSI capability
pci_express 0000:00:03.0:pcie00: allocate port service
pcieport-driver 0000:00:04.0: setting latency timer to 64
pcieport-driver 0000:00:04.0: found MSI capability
pci_express 0000:00:04.0:pcie00: allocate port service
pcieport-driver 0000:00:06.0: setting latency timer to 64
pcieport-driver 0000:00:06.0: found MSI capability
pci_express 0000:00:06.0:pcie00: allocate port service
pcieport-driver 0000:00:1c.0: setting latency timer to 64
pcieport-driver 0000:00:1c.0: found MSI capability
pci_express 0000:00:1c.0:pcie00: allocate port service
pci_express 0000:00:1c.0:pcie02: allocate port service
pcieport-driver 0000:01:00.0: setting latency timer to 64
pcieport-driver 0000:02:01.0: setting latency timer to 64
pcieport-driver 0000:02:01.0: found MSI capability
pcieport-driver 0000:02:02.0: setting latency timer to 64
pcieport-driver 0000:02:02.0: found MSI capability
pcieport-driver 0000:02:03.0: setting latency timer to 64
pcieport-driver 0000:02:03.0: found MSI capability
pcieport-driver 0000:02:04.0: setting latency timer to 64
pcieport-driver 0000:02:04.0: found MSI capability
pcieport-driver 0000:02:05.0: setting latency timer to 64
pcieport-driver 0000:02:05.0: found MSI capability
pcieport-driver 0000:0c:00.0: setting latency timer to 64
pcieport-driver 0000:0d:02.0: setting latency timer to 64
pcieport-driver 0000:0d:02.0: found MSI capability
pcieport-driver 0000:0d:04.0: setting latency timer to 64
pcieport-driver 0000:0d:04.0: found MSI capability
pcieport-driver 0000:10:00.0: setting latency timer to 64
pcieport-driver 0000:11:02.0: setting latency timer to 64
pcieport-driver 0000:11:02.0: found MSI capability
pcieport-driver 0000:11:04.0: setting latency timer to 64
pcieport-driver 0000:11:04.0: found MSI capability
pcieport-driver 0000:16:00.0: setting latency timer to 64
pcieport-driver 0000:17:00.0: setting latency timer to 64
pcieport-driver 0000:17:00.0: found MSI capability
pcieport-driver 0000:17:01.0: setting latency timer to 64
pcieport-driver 0000:17:01.0: found MSI capability
input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
ACPI: Power Button (FF) [PWRF]
processor ACPI0007:00: registered as cooling_device0
processor ACPI0007:01: registered as cooling_device1
processor ACPI0007:02: registered as cooling_device2
processor ACPI0007:03: registered as cooling_device3
processor ACPI0007:04: registered as cooling_device4
processor ACPI0007:05: registered as cooling_device5
processor ACPI0007:06: registered as cooling_device6
processor ACPI0007:07: registered as cooling_device7
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.103
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
pcnet32.c:v1.35 21.Apr.2008 tsbogend@alpha.franken.de
Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.7.9 (July 18, 2008)
bnx2 0000:05:00.0: PCI INT A -> GSI 38 (level, low) -> IRQ 38
eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem dc000000, IRQ 38, node addr 00:1e:c9:d9:84:57
bnx2 0000:07:00.0: PCI INT A -> GSI 37 (level, low) -> IRQ 37
eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem da000000, IRQ 37, node addr 00:1e:c9:d9:84:59
bnx2 0000:09:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
eth2: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem d8000000, IRQ 19, node addr 00:1e:c9:d9:84:5b
bnx2 0000:0b:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
eth3: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem d6000000, IRQ 18, node addr 00:1e:c9:d9:84:5d
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
Uniform Multi-Platform E-IDE driver
ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports
Probing IDE interface ide0...
hda: TSSTcorpDVD-ROM TS-L333A, ATAPI CD/DVD-ROM drive
Probing IDE interface ide1...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
megasas: 00.00.03.20-rc1 Mon. March 10 11:02:31 PDT 2008
megasas: 0x1000:0x0060:0x1028:0x1f0c: bus 25:slot 0:func 0
megaraid_sas 0000:19:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
megaraid_sas 0000:19:00.0: setting latency timer to 64
megasas: FW now in Ready state
scsi0 : LSI SAS based MegaRAID driver
scsi 0:0:0:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:1:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:2:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:3:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:4:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:5:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:6:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:7:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:32:0: Enclosure         DP       BACKPLANE        1.06 PQ: 0 ANSI: 5
scsi 0:2:0:0: Direct-Access     DELL     PERC 6/i         1.11 PQ: 0 ANSI: 5
Driver 'sd' needs updating - please use bus_type methods
sd 0:2:0:0: [sda] 710410240 512-byte hardware sectors (363730 MB)
sd 0:2:0:0: [sda] Write Protect is off
sd 0:2:0:0: [sda] Mode Sense: 1f 00 00 08
sd 0:2:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:2:0:0: [sda] 710410240 512-byte hardware sectors (363730 MB)
sd 0:2:0:0: [sda] Write Protect is off
sd 0:2:0:0: [sda] Mode Sense: 1f 00 00 08
sd 0:2:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 sda13 sda14 sda15 >
sd 0:2:0:0: [sda] Attached SCSI disk
ata_piix 0000:00:1f.2: version 2.12
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
ata_piix 0000:00:1f.2: BAR 0: can't reserve I/O region [0x1f0-0x1f7]
ata_piix 0000:00:1f.2: failed to request/iomap BARs for port 0 (errno=-16)
ata_piix 0000:00:1f.2: BAR 2: can't reserve I/O region [0x170-0x177]
ata_piix 0000:00:1f.2: failed to request/iomap BARs for port 1 (errno=-16)
ata_piix 0000:00:1f.2: no available native port
Fusion MPT base driver 3.04.07
Copyright (c) 1999-2008 LSI Corporation
Fusion MPT SPI Host driver 3.04.07
ehci_hcd 0000:00:1d.7: PCI INT B -> GSI 21 (level, low) -> IRQ 21
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 21, io mem 0xde0ffc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.27-rc3 ehci_hcd
usb usb1: SerialNumber: 0000:00:1d.7
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
USB Universal Host Controller Interface driver v3.0
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 20, io base 0x0000cc80
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb 1-2: new high speed USB device using ehci_hcd and address 2
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.27-rc3 uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.0
uhci_hcd 0000:00:1d.1: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 20, io base 0x0000cca0
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 1-2: configuration #1 chosen from 1 choice
hub 1-2:1.0: USB hub found
hub 1-2:1.0: 2 ports detected
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.27-rc3 uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.1
uhci_hcd 0000:00:1d.2: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 20, io base 0x0000ccc0
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-2: New USB device found, idVendor=413c, idProduct=a001
usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.27-rc3 uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.2
uhci_hcd 0000:00:1d.3: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1d.3: setting latency timer to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 20, io base 0x0000cce0
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 1-7: new high speed USB device using ehci_hcd and address 4
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.27-rc3 uhci_hcd
usb usb5: SerialNumber: 0000:00:1d.3
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
usb 1-7: configuration #1 chosen from 1 choice
hub 1-7:1.0: USB hub found
hub 1-7:1.0: 2 ports detected
input: PC Speaker as /devices/platform/pcspkr/input/input1
coretemp coretemp.0: Using relative temperature scale!
coretemp coretemp.1: Using relative temperature scale!
coretemp coretemp.2: Using relative temperature scale!
coretemp coretemp.3: Using relative temperature scale!
coretemp coretemp.4: Using relative temperature scale!
coretemp coretemp.5: Using relative temperature scale!
coretemp coretemp.6: Using relative temperature scale!
coretemp coretemp.7: Using relative temperature scale!
hdaps: supported laptop not found!
hdaps: driver init failed (ret=-19)!
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
EDAC MC: Ver: 2.1.0 Aug 14 2008
usb 1-7: New USB device found, idVendor=04b4, idProduct=6560
usb 1-7: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 3-1: new low speed USB device using uhci_hcd and address 2
usb 3-1: configuration #1 chosen from 1 choice
usb 3-1: New USB device found, idVendor=0624, idProduct=0294
usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 3-1: Product: Dell 03R874
usb 3-1: Manufacturer: Avocent
usb 1-2.1: new full speed USB device using ehci_hcd and address 5
usb 1-2.1: configuration #1 chosen from 1 choice
usb 1-2.1: New USB device found, idVendor=413c, idProduct=0000
usb 1-2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-2.1: Product: DRAC5
usb 1-2.1: Manufacturer: Dell
usb 1-2.1: SerialNumber: 0000000
usb 1-7.1: new high speed USB device using ehci_hcd and address 6
usb 1-7.1: configuration #1 chosen from 1 choice
hub 1-7.1:1.0: USB hub found
hub 1-7.1:1.0: 2 ports detected
usb 1-7.1: New USB device found, idVendor=04b4, idProduct=6560
usb 1-7.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usbcore: registered new interface driver hiddev
input: Avocent Dell 03R874 as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input2
input: USB HID v1.10 Keyboard [Avocent Dell 03R874] on usb-0000:00:1d.1-1
input: Avocent Dell 03R874 as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.1/input/input3
input: USB HID v1.10 Mouse [Avocent Dell 03R874] on usb-0000:00:1d.1-1
input: Dell DRAC5 as /devices/pci0000:00/0000:00:1d.7/usb1/1-2/1-2.1/1-2.1:1.0/input/input4
input: USB HID v1.10 Keyboard [Dell DRAC5] on usb-0000:00:1d.7-2.1
input: Dell DRAC5 as /devices/pci0000:00/0000:00:1d.7/usb1/1-2/1-2.1/1-2.1:1.1/input/input5
input: USB HID v1.10 Mouse [Dell DRAC5] on usb-0000:00:1d.7-2.1
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.17.
ALSA device list:
  No soundcards found.
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 17
Starting balanced_irq
Using IPI No-Shortcut mode
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 260k freed
Adding 27350652k swap on /dev/sda3.  Priority:-1 extents:1 across:27350652k
bnx2: eth0: using MSI
bnx2: eth1: using MSI
bnx2: eth0 NIC Copper Link is Up, 1000 Mbps full duplex

[-- Attachment #3: Type: TEXT/PLAIN, Size: 31509 bytes --]

096K
CPU: Physical Processor ID: 4
CPU: Processor Core ID: 0
CPU2: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#2]: passed.
CPU 3 irqstacks, hard=c0529000 soft=c0519000
Booting processor 3/24 ip 6000
Initializing CPU#3
Calibrating delay using timer specific routine.. 3723.88 BogoMIPS (lpj=7447771)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 6
CPU: Processor Core ID: 0
CPU3: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#3]: passed.
CPU 4 irqstacks, hard=c052a000 soft=c051a000
Booting processor 4/2 ip 6000
Initializing CPU#4
Calibrating delay using timer specific routine.. 3723.86 BogoMIPS (lpj=7447739)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 2
CPU4: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#4]: passed.
CPU 5 irqstacks, hard=c052b000 soft=c051b000
Booting processor 5/10 ip 6000
Initializing CPU#5
Calibrating delay using timer specific routine.. 3723.90 BogoMIPS (lpj=7447817)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 2
CPU5: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#5]: passed.
CPU 6 irqstacks, hard=c052c000 soft=c051c000
Booting processor 6/18 ip 6000
Initializing CPU#6
Calibrating delay using timer specific routine.. 3723.91 BogoMIPS (lpj=7447836)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 4
CPU: Processor Core ID: 2
CPU6: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#6]: passed.
CPU 7 irqstacks, hard=c052d000 soft=c051d000
Booting processor 7/26 ip 6000
Initializing CPU#7
Calibrating delay using timer specific routine.. 3723.90 BogoMIPS (lpj=7447812)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 6
CPU: Processor Core ID: 2
CPU7: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#7]: passed.
Brought up 8 CPUs
Total of 8 processors activated (29791.10 BogoMIPS).
net_namespace: 596 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
No dock devices found.
ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
ACPI: bus type pci registered
PCI: Using configuration type 1 for base access
PCI: Dell PowerEdge R900 detected, enabling pci=bfsort.
ACPI: EC: Look up EC in DSDT
ACPI: BIOS _OSI(Linux) query ignored
ACPI: DMI System Vendor: Dell Inc.
ACPI: DMI Product Name: PowerEdge R900
ACPI: DMI Product Version: 
ACPI: DMI Board Name: 0C764H
ACPI: DMI BIOS Vendor: Dell Inc.
ACPI: DMI BIOS Date: 03/23/2008
ACPI: Please send DMI info above to linux-acpi@vger.kernel.org
ACPI: If "acpi_osi=Linux" works better, please notify linux-acpi@vger.kernel.org
ACPI: Interpreter enabled
ACPI: (supports S0 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
pci 0000:00:00.0: PME# disabled
pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
pci 0000:00:01.0: PME# disabled
pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
pci 0000:00:02.0: PME# disabled
pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
pci 0000:00:03.0: PME# disabled
pci 0000:00:04.0: PME# supported from D0 D3hot D3cold
pci 0000:00:04.0: PME# disabled
pci 0000:00:06.0: PME# supported from D0 D3hot D3cold
pci 0000:00:06.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:16:00.0: PME# supported from D0 D3hot D3cold
pci 0000:16:00.0: PME# disabled
pci 0000:16:00.3: PME# supported from D0 D3hot D3cold
pci 0000:16:00.3: PME# disabled
pci 0000:17:00.0: PME# supported from D0 D3hot D3cold
pci 0000:17:00.0: PME# disabled
pci 0000:17:01.0: PME# supported from D0 D3hot D3cold
pci 0000:17:01.0: PME# disabled
pci 0000:19:00.0: supports D1
pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
pci 0000:01:00.0: PME# disabled
pci 0000:02:01.0: PME# supported from D0 D3hot D3cold
pci 0000:02:01.0: PME# disabled
pci 0000:02:02.0: PME# supported from D0 D3hot D3cold
pci 0000:02:02.0: PME# disabled
pci 0000:02:03.0: PME# supported from D0 D3hot D3cold
pci 0000:02:03.0: PME# disabled
pci 0000:02:04.0: PME# supported from D0 D3hot D3cold
pci 0000:02:04.0: PME# disabled
pci 0000:02:05.0: PME# supported from D0 D3hot D3cold
pci 0000:02:05.0: PME# disabled
pci 0000:0a:00.0: PME# supported from D0 D3hot D3cold
pci 0000:0a:00.0: PME# disabled
pci 0000:0b:00.0: PME# supported from D3hot D3cold
pci 0000:0b:00.0: PME# disabled
pci 0000:08:00.0: PME# supported from D0 D3hot D3cold
pci 0000:08:00.0: PME# disabled
pci 0000:09:00.0: PME# supported from D3hot D3cold
pci 0000:09:00.0: PME# disabled
pci 0000:06:00.0: PME# supported from D0 D3hot D3cold
pci 0000:06:00.0: PME# disabled
pci 0000:07:00.0: PME# supported from D3hot D3cold
pci 0000:07:00.0: PME# disabled
pci 0000:04:00.0: PME# supported from D0 D3hot D3cold
pci 0000:04:00.0: PME# disabled
pci 0000:05:00.0: PME# supported from D3hot D3cold
pci 0000:05:00.0: PME# disabled
pci 0000:0c:00.0: PME# supported from D0 D3hot D3cold
pci 0000:0c:00.0: PME# disabled
pci 0000:0d:02.0: PME# supported from D0 D3hot D3cold
pci 0000:0d:02.0: PME# disabled
pci 0000:0d:04.0: PME# supported from D0 D3hot D3cold
pci 0000:0d:04.0: PME# disabled
pci 0000:10:00.0: PME# supported from D0 D3hot D3cold
pci 0000:10:00.0: PME# disabled
pci 0000:11:02.0: PME# supported from D0 D3hot D3cold
pci 0000:11:02.0: PME# disabled
pci 0000:11:04.0: PME# supported from D0 D3hot D3cold
pci 0000:11:04.0: PME# disabled
pci 0000:1b:0c.0: supports D1
pci 0000:1b:0c.0: supports D2
pci 0000:00:1e.0: transparent bridge
bus 00 -> node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2.UPST._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2.UPST.DWN1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2.UPST.DWN2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3.UPST.DWN2.BCOM._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3.UPST.DWN3.BCOM._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3.UPST.DWN4.BCOM._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3.UPST.DWN5.BCOM._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4.UPST.DWNB._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4.UPST.DWNC._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX6.UPST.DWNB._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX6.UPST.DWNC._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.SBEX._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.COMP._PRT]
ACPI: PCI Interrupt Link [LK00] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LK01] (IRQs 3 4 5 6 7 *10 11 12)
ACPI: PCI Interrupt Link [LK02] (IRQs 3 4 5 *6 7 10 11 12)
ACPI: PCI Interrupt Link [LK03] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LK04] (IRQs 3 4 *5 6 7 10 11 12)
ACPI: PCI Interrupt Link [LK05] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LK06] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LK07] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
Switched to high resolution mode on CPU 0
Switched to high resolution mode on CPU 4
Switched to high resolution mode on CPU 3
Switched to high resolution mode on CPU 5
Switched to high resolution mode on CPU 2
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 7
Switched to high resolution mode on CPU 6
system 00:07: ioport range 0x800-0x87f has been reserved
system 00:07: ioport range 0x880-0x8bf has been reserved
system 00:07: ioport range 0x8c0-0x8df has been reserved
system 00:07: ioport range 0x8e0-0x8e3 has been reserved
system 00:07: ioport range 0x8f0-0x8f1 has been reserved
system 00:07: ioport range 0x900-0x900 has been reserved
system 00:07: ioport range 0xc00-0xc7f has been reserved
system 00:07: ioport range 0xca0-0xca7 has been reserved
system 00:07: ioport range 0xca9-0xcab has been reserved
system 00:07: ioport range 0xcad-0xcaf has been reserved
system 00:08: ioport range 0xca8-0xca8 has been reserved
system 00:08: ioport range 0xcac-0xcac has been reserved
system 00:09: iomem range 0xe0000000-0xefffffff could not be reserved
pci 0000:00:01.0: PCI bridge, secondary bus 0000:14
pci 0000:00:01.0:   IO window: disabled
pci 0000:00:01.0:   MEM window: disabled
pci 0000:00:01.0:   PREFETCH window: disabled
pci 0000:17:00.0: PCI bridge, secondary bus 0000:19
pci 0000:17:00.0:   IO window: 0xe000-0xefff
pci 0000:17:00.0:   MEM window: 0xde200000-0xde3fffff
pci 0000:17:00.0:   PREFETCH window: disabled
pci 0000:17:01.0: PCI bridge, secondary bus 0000:18
pci 0000:17:01.0:   IO window: disabled
pci 0000:17:01.0:   MEM window: disabled
pci 0000:17:01.0:   PREFETCH window: disabled
pci 0000:16:00.0: PCI bridge, secondary bus 0000:17
pci 0000:16:00.0:   IO window: 0xe000-0xefff
pci 0000:16:00.0:   MEM window: 0xde200000-0xde3fffff
pci 0000:16:00.0:   PREFETCH window: disabled
pci 0000:16:00.3: PCI bridge, secondary bus 0000:1a
pci 0000:16:00.3:   IO window: disabled
pci 0000:16:00.3:   MEM window: disabled
pci 0000:16:00.3:   PREFETCH window: disabled
pci 0000:00:02.0: PCI bridge, secondary bus 0000:16
pci 0000:00:02.0:   IO window: 0xe000-0xefff
pci 0000:00:02.0:   MEM window: 0xde100000-0xde3fffff
pci 0000:00:02.0:   PREFETCH window: disabled
pci 0000:02:01.0: PCI bridge, secondary bus 0000:03
pci 0000:02:01.0:   IO window: disabled
pci 0000:02:01.0:   MEM window: disabled
pci 0000:02:01.0:   PREFETCH window: disabled
pci 0000:0a:00.0: PCI bridge, secondary bus 0000:0b
pci 0000:0a:00.0:   IO window: disabled
pci 0000:0a:00.0:   MEM window: 0xd6000000-0xd7ffffff
pci 0000:0a:00.0:   PREFETCH window: disabled
pci 0000:02:02.0: PCI bridge, secondary bus 0000:0a
pci 0000:02:02.0:   IO window: disabled
pci 0000:02:02.0:   MEM window: 0xd6000000-0xd7ffffff
pci 0000:02:02.0:   PREFETCH window: disabled
pci 0000:08:00.0: PCI bridge, secondary bus 0000:09
pci 0000:08:00.0:   IO window: disabled
pci 0000:08:00.0:   MEM window: 0xd8000000-0xd9ffffff
pci 0000:08:00.0:   PREFETCH window: disabled
pci 0000:02:03.0: PCI bridge, secondary bus 0000:08
pci 0000:02:03.0:   IO window: disabled
pci 0000:02:03.0:   MEM window: 0xd8000000-0xd9ffffff
pci 0000:02:03.0:   PREFETCH window: disabled
pci 0000:06:00.0: PCI bridge, secondary bus 0000:07
pci 0000:06:00.0:   IO window: disabled
pci 0000:06:00.0:   MEM window: 0xda000000-0xdbffffff
pci 0000:06:00.0:   PREFETCH window: disabled
pci 0000:02:04.0: PCI bridge, secondary bus 0000:06
pci 0000:02:04.0:   IO window: disabled
pci 0000:02:04.0:   MEM window: 0xda000000-0xdbffffff
pci 0000:02:04.0:   PREFETCH window: disabled
pci 0000:04:00.0: PCI bridge, secondary bus 0000:05
pci 0000:04:00.0:   IO window: disabled
pci 0000:04:00.0:   MEM window: 0xdc000000-0xddffffff
pci 0000:04:00.0:   PREFETCH window: disabled
pci 0000:02:05.0: PCI bridge, secondary bus 0000:04
pci 0000:02:05.0:   IO window: disabled
pci 0000:02:05.0:   MEM window: 0xdc000000-0xddffffff
pci 0000:02:05.0:   PREFETCH window: disabled
pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
pci 0000:01:00.0:   IO window: disabled
pci 0000:01:00.0:   MEM window: 0xd6000000-0xddffffff
pci 0000:01:00.0:   PREFETCH window: disabled
pci 0000:00:03.0: PCI bridge, secondary bus 0000:01
pci 0000:00:03.0:   IO window: disabled
pci 0000:00:03.0:   MEM window: 0xd6000000-0xddffffff
pci 0000:00:03.0:   PREFETCH window: disabled
pci 0000:0d:02.0: PCI bridge, secondary bus 0000:0f
pci 0000:0d:02.0:   IO window: disabled
pci 0000:0d:02.0:   MEM window: disabled
pci 0000:0d:02.0:   PREFETCH window: disabled
pci 0000:0d:04.0: PCI bridge, secondary bus 0000:0e
pci 0000:0d:04.0:   IO window: disabled
pci 0000:0d:04.0:   MEM window: disabled
pci 0000:0d:04.0:   PREFETCH window: disabled
pci 0000:0c:00.0: PCI bridge, secondary bus 0000:0d
pci 0000:0c:00.0:   IO window: disabled
pci 0000:0c:00.0:   MEM window: disabled
pci 0000:0c:00.0:   PREFETCH window: disabled
pci 0000:00:04.0: PCI bridge, secondary bus 0000:0c
pci 0000:00:04.0:   IO window: disabled
pci 0000:00:04.0:   MEM window: disabled
pci 0000:00:04.0:   PREFETCH window: disabled
pci 0000:11:02.0: PCI bridge, secondary bus 0000:13
pci 0000:11:02.0:   IO window: disabled
pci 0000:11:02.0:   MEM window: disabled
pci 0000:11:02.0:   PREFETCH window: disabled
pci 0000:11:04.0: PCI bridge, secondary bus 0000:12
pci 0000:11:04.0:   IO window: disabled
pci 0000:11:04.0:   MEM window: disabled
pci 0000:11:04.0:   PREFETCH window: disabled
pci 0000:10:00.0: PCI bridge, secondary bus 0000:11
pci 0000:10:00.0:   IO window: disabled
pci 0000:10:00.0:   MEM window: disabled
pci 0000:10:00.0:   PREFETCH window: disabled
pci 0000:00:06.0: PCI bridge, secondary bus 0000:10
pci 0000:00:06.0:   IO window: disabled
pci 0000:00:06.0:   MEM window: disabled
pci 0000:00:06.0:   PREFETCH window: disabled
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:15
pci 0000:00:1c.0:   IO window: disabled
pci 0000:00:1c.0:   MEM window: disabled
pci 0000:00:1c.0:   PREFETCH window: disabled
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:1b
pci 0000:00:1e.0:   IO window: 0xd000-0xdfff
pci 0000:00:1e.0:   MEM window: 0xde400000-0xde4fffff
pci 0000:00:1e.0:   PREFETCH window: 0x000000c8000000-0x000000cfffffff
pci 0000:00:01.0: PCI INT A -> GSI 36 (level, low) -> IRQ 36
pci 0000:00:01.0: setting latency timer to 64
pci 0000:00:02.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:02.0: setting latency timer to 64
pci 0000:16:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:16:00.0: setting latency timer to 64
pci 0000:17:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:17:00.0: setting latency timer to 64
pci 0000:17:01.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
pci 0000:17:01.0: setting latency timer to 64
pci 0000:16:00.3: setting latency timer to 64
pci 0000:00:03.0: PCI INT A -> GSI 37 (level, low) -> IRQ 37
pci 0000:00:03.0: setting latency timer to 64
pci 0000:01:00.0: setting latency timer to 64
pci 0000:02:01.0: setting latency timer to 64
pci 0000:02:02.0: setting latency timer to 64
pci 0000:0a:00.0: setting latency timer to 64
pci 0000:02:03.0: setting latency timer to 64
pci 0000:08:00.0: setting latency timer to 64
pci 0000:02:04.0: setting latency timer to 64
pci 0000:06:00.0: setting latency timer to 64
pci 0000:02:05.0: setting latency timer to 64
pci 0000:04:00.0: setting latency timer to 64
pci 0000:00:04.0: PCI INT A -> GSI 32 (level, low) -> IRQ 32
pci 0000:00:04.0: setting latency timer to 64
pci 0000:0c:00.0: setting latency timer to 64
pci 0000:0d:02.0: setting latency timer to 64
pci 0000:0d:04.0: setting latency timer to 64
pci 0000:00:06.0: PCI INT A -> GSI 33 (level, low) -> IRQ 33
pci 0000:00:06.0: setting latency timer to 64
pci 0000:10:00.0: setting latency timer to 64
pci 0000:11:02.0: setting latency timer to 64
pci 0000:11:04.0: setting latency timer to 64
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
highmem bounce pool size: 64 pages
HugeTLB registered 2 MB page size, pre-allocated 0 pages
msgmni has been set to 1235
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered (default)
pci 0000:1b:0c.0: Boot video device
pcieport-driver 0000:00:01.0: setting latency timer to 64
pcieport-driver 0000:00:01.0: found MSI capability
pci_express 0000:00:01.0:pcie00: allocate port service
pcieport-driver 0000:00:02.0: setting latency timer to 64
pcieport-driver 0000:00:02.0: found MSI capability
pci_express 0000:00:02.0:pcie00: allocate port service
pcieport-driver 0000:00:03.0: setting latency timer to 64
pcieport-driver 0000:00:03.0: found MSI capability
pci_express 0000:00:03.0:pcie00: allocate port service
pcieport-driver 0000:00:04.0: setting latency timer to 64
pcieport-driver 0000:00:04.0: found MSI capability
pci_express 0000:00:04.0:pcie00: allocate port service
pcieport-driver 0000:00:06.0: setting latency timer to 64
pcieport-driver 0000:00:06.0: found MSI capability
pci_express 0000:00:06.0:pcie00: allocate port service
pcieport-driver 0000:00:1c.0: setting latency timer to 64
pcieport-driver 0000:00:1c.0: found MSI capability
pci_express 0000:00:1c.0:pcie00: allocate port service
pci_express 0000:00:1c.0:pcie02: allocate port service
pcieport-driver 0000:01:00.0: setting latency timer to 64
pcieport-driver 0000:02:01.0: setting latency timer to 64
pcieport-driver 0000:02:01.0: found MSI capability
pcieport-driver 0000:02:02.0: setting latency timer to 64
pcieport-driver 0000:02:02.0: found MSI capability
pcieport-driver 0000:02:03.0: setting latency timer to 64
pcieport-driver 0000:02:03.0: found MSI capability
pcieport-driver 0000:02:04.0: setting latency timer to 64
pcieport-driver 0000:02:04.0: found MSI capability
pcieport-driver 0000:02:05.0: setting latency timer to 64
pcieport-driver 0000:02:05.0: found MSI capability
pcieport-driver 0000:0c:00.0: setting latency timer to 64
pcieport-driver 0000:0d:02.0: setting latency timer to 64
pcieport-driver 0000:0d:02.0: found MSI capability
pcieport-driver 0000:0d:04.0: setting latency timer to 64
pcieport-driver 0000:0d:04.0: found MSI capability
pcieport-driver 0000:10:00.0: setting latency timer to 64
pcieport-driver 0000:11:02.0: setting latency timer to 64
pcieport-driver 0000:11:02.0: found MSI capability
pcieport-driver 0000:11:04.0: setting latency timer to 64
pcieport-driver 0000:11:04.0: found MSI capability
pcieport-driver 0000:16:00.0: setting latency timer to 64
pcieport-driver 0000:17:00.0: setting latency timer to 64
pcieport-driver 0000:17:00.0: found MSI capability
pcieport-driver 0000:17:01.0: setting latency timer to 64
pcieport-driver 0000:17:01.0: found MSI capability
input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
ACPI: Power Button (FF) [PWRF]
processor ACPI0007:00: registered as cooling_device0
processor ACPI0007:01: registered as cooling_device1
processor ACPI0007:02: registered as cooling_device2
processor ACPI0007:03: registered as cooling_device3
processor ACPI0007:04: registered as cooling_device4
processor ACPI0007:05: registered as cooling_device5
processor ACPI0007:06: registered as cooling_device6
processor ACPI0007:07: registered as cooling_device7
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.103
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
pcnet32.c:v1.35 21.Apr.2008 tsbogend@alpha.franken.de
Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.7.9 (July 18, 2008)
bnx2 0000:05:00.0: PCI INT A -> GSI 38 (level, low) -> IRQ 38
eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem dc000000, IRQ 38, node addr 00:1e:c9:d9:84:57
bnx2 0000:07:00.0: PCI INT A -> GSI 37 (level, low) -> IRQ 37
eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem da000000, IRQ 37, node addr 00:1e:c9:d9:84:59
bnx2 0000:09:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
eth2: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem d8000000, IRQ 19, node addr 00:1e:c9:d9:84:5b
bnx2 0000:0b:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
eth3: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem d6000000, IRQ 18, node addr 00:1e:c9:d9:84:5d
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
Uniform Multi-Platform E-IDE driver
ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports
Probing IDE interface ide0...
hda: TSSTcorpDVD-ROM TS-L333A, ATAPI CD/DVD-ROM drive
Probing IDE interface ide1...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
megasas: 00.00.03.20-rc1 Mon. March 10 11:02:31 PDT 2008
megasas: 0x1000:0x0060:0x1028:0x1f0c: bus 25:slot 0:func 0
megaraid_sas 0000:19:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
megaraid_sas 0000:19:00.0: setting latency timer to 64
megasas: FW now in Ready state
scsi0 : LSI SAS based MegaRAID driver
scsi 0:0:0:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:1:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:2:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:3:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:4:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:5:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:6:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:7:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:32:0: Enclosure         DP       BACKPLANE        1.06 PQ: 0 ANSI: 5
scsi 0:2:0:0: Direct-Access     DELL     PERC 6/i         1.11 PQ: 0 ANSI: 5
Driver 'sd' needs updating - please use bus_type methods
sd 0:2:0:0: [sda] 710410240 512-byte hardware sectors (363730 MB)
sd 0:2:0:0: [sda] Write Protect is off
sd 0:2:0:0: [sda] Mode Sense: 1f 00 00 08
sd 0:2:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:2:0:0: [sda] 710410240 512-byte hardware sectors (363730 MB)
sd 0:2:0:0: [sda] Write Protect is off
sd 0:2:0:0: [sda] Mode Sense: 1f 00 00 08
sd 0:2:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 sda13 sda14 sda15 >
sd 0:2:0:0: [sda] Attached SCSI disk
ata_piix 0000:00:1f.2: version 2.12
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
ata_piix 0000:00:1f.2: BAR 0: can't reserve I/O region [0x1f0-0x1f7]
ata_piix 0000:00:1f.2: failed to request/iomap BARs for port 0 (errno=-16)
ata_piix 0000:00:1f.2: BAR 2: can't reserve I/O region [0x170-0x177]
ata_piix 0000:00:1f.2: failed to request/iomap BARs for port 1 (errno=-16)
ata_piix 0000:00:1f.2: no available native port
Fusion MPT base driver 3.04.07
Copyright (c) 1999-2008 LSI Corporation
Fusion MPT SPI Host driver 3.04.07
ehci_hcd 0000:00:1d.7: PCI INT B -> GSI 21 (level, low) -> IRQ 21
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 21, io mem 0xde0ffc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.27-rc3 ehci_hcd
usb usb1: SerialNumber: 0000:00:1d.7
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
USB Universal Host Controller Interface driver v3.0
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 20, io base 0x0000cc80
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb 1-2: new high speed USB device using ehci_hcd and address 2
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.27-rc3 uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.0
uhci_hcd 0000:00:1d.1: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 20, io base 0x0000cca0
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 1-2: configuration #1 chosen from 1 choice
hub 1-2:1.0: USB hub found
hub 1-2:1.0: 2 ports detected
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.27-rc3 uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.1
uhci_hcd 0000:00:1d.2: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 20, io base 0x0000ccc0
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-2: New USB device found, idVendor=413c, idProduct=a001
usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.27-rc3 uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.2
uhci_hcd 0000:00:1d.3: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1d.3: setting latency timer to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 20, io base 0x0000cce0
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 1-7: new high speed USB device using ehci_hcd and address 4
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.27-rc3 uhci_hcd
usb usb5: SerialNumber: 0000:00:1d.3
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
usb 1-7: configuration #1 chosen from 1 choice
hub 1-7:1.0: USB hub found
hub 1-7:1.0: 2 ports detected
input: PC Speaker as /devices/platform/pcspkr/input/input1
coretemp coretemp.0: Using relative temperature scale!
coretemp coretemp.1: Using relative temperature scale!
coretemp coretemp.2: Using relative temperature scale!
coretemp coretemp.3: Using relative temperature scale!
coretemp coretemp.4: Using relative temperature scale!
coretemp coretemp.5: Using relative temperature scale!
coretemp coretemp.6: Using relative temperature scale!
coretemp coretemp.7: Using relative temperature scale!
hdaps: supported laptop not found!
hdaps: driver init failed (ret=-19)!
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
EDAC MC: Ver: 2.1.0 Aug 14 2008
usb 1-7: New USB device found, idVendor=04b4, idProduct=6560
usb 1-7: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 3-1: new low speed USB device using uhci_hcd and address 2
usb 3-1: configuration #1 chosen from 1 choice
usb 3-1: New USB device found, idVendor=0624, idProduct=0294
usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 3-1: Product: Dell 03R874
usb 3-1: Manufacturer: Avocent
usb 1-2.1: new full speed USB device using ehci_hcd and address 5
usb 1-2.1: configuration #1 chosen from 1 choice
usb 1-2.1: New USB device found, idVendor=413c, idProduct=0000
usb 1-2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-2.1: Product: DRAC5
usb 1-2.1: Manufacturer: Dell
usb 1-2.1: SerialNumber: 0000000
usb 1-7.1: new high speed USB device using ehci_hcd and address 6
usb 1-7.1: configuration #1 chosen from 1 choice
hub 1-7.1:1.0: USB hub found
hub 1-7.1:1.0: 2 ports detected
usb 1-7.1: New USB device found, idVendor=04b4, idProduct=6560
usb 1-7.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usbcore: registered new interface driver hiddev
input: Avocent Dell 03R874 as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input2
input: USB HID v1.10 Keyboard [Avocent Dell 03R874] on usb-0000:00:1d.1-1
input: Avocent Dell 03R874 as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.1/input/input3
input: USB HID v1.10 Mouse [Avocent Dell 03R874] on usb-0000:00:1d.1-1
input: Dell DRAC5 as /devices/pci0000:00/0000:00:1d.7/usb1/1-2/1-2.1/1-2.1:1.0/input/input4
input: USB HID v1.10 Keyboard [Dell DRAC5] on usb-0000:00:1d.7-2.1
input: Dell DRAC5 as /devices/pci0000:00/0000:00:1d.7/usb1/1-2/1-2.1/1-2.1:1.1/input/input5
input: USB HID v1.10 Mouse [Dell DRAC5] on usb-0000:00:1d.7-2.1
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.17.
ALSA device list:
  No soundcards found.
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 17
Starting balanced_irq
Using IPI No-Shortcut mode
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 260k freed
Adding 27350652k swap on /dev/sda3.  Priority:-1 extents:1 across:27350652k
bnx2: eth0: using MSI
bnx2: eth1: using MSI
bnx2: eth0 NIC Copper Link is Up, 1000 Mbps full duplex

[-- Attachment #4: Type: TEXT/PLAIN, Size: 31519 bytes --]

ID: 2
CPU: Processor Core ID: 3
CPU13: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#13]: passed.
CPU 14 irqstacks, hard=c0534000 soft=c0524000
Booting processor 14/19 ip 6000
Initializing CPU#14
Leaving ESR disabled.
Calibrating delay using timer specific routine.. 3723.88 BogoMIPS (lpj=7447761)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 4
CPU: Processor Core ID: 3
CPU14: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#14]: passed.
CPU 15 irqstacks, hard=c0535000 soft=c0525000
Booting processor 15/27 ip 6000
Initializing CPU#15
Leaving ESR disabled.
Calibrating delay using timer specific routine.. 3723.89 BogoMIPS (lpj=7447782)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 6
CPU: Processor Core ID: 3
CPU15: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#15]: passed.
Brought up 16 CPUs
Total of 16 processors activated (59582.26 BogoMIPS).
net_namespace: 596 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
No dock devices found.
ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
ACPI: bus type pci registered
PCI: Using configuration type 1 for base access
PCI: Dell PowerEdge R900 detected, enabling pci=bfsort.
ACPI: EC: Look up EC in DSDT
ACPI: BIOS _OSI(Linux) query ignored
ACPI: DMI System Vendor: Dell Inc.
ACPI: DMI Product Name: PowerEdge R900
ACPI: DMI Product Version: 
ACPI: DMI Board Name: 0C764H
ACPI: DMI BIOS Vendor: Dell Inc.
ACPI: DMI BIOS Date: 03/23/2008
ACPI: Please send DMI info above to linux-acpi@vger.kernel.org
ACPI: If "acpi_osi=Linux" works better, please notify linux-acpi@vger.kernel.org
ACPI: Interpreter enabled
ACPI: (supports S0 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
pci 0000:00:00.0: PME# disabled
pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
pci 0000:00:01.0: PME# disabled
pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
pci 0000:00:02.0: PME# disabled
pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
pci 0000:00:03.0: PME# disabled
pci 0000:00:04.0: PME# supported from D0 D3hot D3cold
pci 0000:00:04.0: PME# disabled
pci 0000:00:06.0: PME# supported from D0 D3hot D3cold
pci 0000:00:06.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:16:00.0: PME# supported from D0 D3hot D3cold
pci 0000:16:00.0: PME# disabled
pci 0000:16:00.3: PME# supported from D0 D3hot D3cold
pci 0000:16:00.3: PME# disabled
pci 0000:17:00.0: PME# supported from D0 D3hot D3cold
pci 0000:17:00.0: PME# disabled
pci 0000:17:01.0: PME# supported from D0 D3hot D3cold
pci 0000:17:01.0: PME# disabled
pci 0000:19:00.0: supports D1
pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
pci 0000:01:00.0: PME# disabled
pci 0000:02:01.0: PME# supported from D0 D3hot D3cold
pci 0000:02:01.0: PME# disabled
pci 0000:02:02.0: PME# supported from D0 D3hot D3cold
pci 0000:02:02.0: PME# disabled
pci 0000:02:03.0: PME# supported from D0 D3hot D3cold
pci 0000:02:03.0: PME# disabled
pci 0000:02:04.0: PME# supported from D0 D3hot D3cold
pci 0000:02:04.0: PME# disabled
pci 0000:02:05.0: PME# supported from D0 D3hot D3cold
pci 0000:02:05.0: PME# disabled
pci 0000:0a:00.0: PME# supported from D0 D3hot D3cold
pci 0000:0a:00.0: PME# disabled
pci 0000:0b:00.0: PME# supported from D3hot D3cold
pci 0000:0b:00.0: PME# disabled
pci 0000:08:00.0: PME# supported from D0 D3hot D3cold
pci 0000:08:00.0: PME# disabled
pci 0000:09:00.0: PME# supported from D3hot D3cold
pci 0000:09:00.0: PME# disabled
pci 0000:06:00.0: PME# supported from D0 D3hot D3cold
pci 0000:06:00.0: PME# disabled
pci 0000:07:00.0: PME# supported from D3hot D3cold
pci 0000:07:00.0: PME# disabled
pci 0000:04:00.0: PME# supported from D0 D3hot D3cold
pci 0000:04:00.0: PME# disabled
pci 0000:05:00.0: PME# supported from D3hot D3cold
pci 0000:05:00.0: PME# disabled
pci 0000:0c:00.0: PME# supported from D0 D3hot D3cold
pci 0000:0c:00.0: PME# disabled
pci 0000:0d:02.0: PME# supported from D0 D3hot D3cold
pci 0000:0d:02.0: PME# disabled
pci 0000:0d:04.0: PME# supported from D0 D3hot D3cold
pci 0000:0d:04.0: PME# disabled
pci 0000:10:00.0: PME# supported from D0 D3hot D3cold
pci 0000:10:00.0: PME# disabled
pci 0000:11:02.0: PME# supported from D0 D3hot D3cold
pci 0000:11:02.0: PME# disabled
pci 0000:11:04.0: PME# supported from D0 D3hot D3cold
pci 0000:11:04.0: PME# disabled
pci 0000:1b:0c.0: supports D1
pci 0000:1b:0c.0: supports D2
pci 0000:00:1e.0: transparent bridge
bus 00 -> node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2.UPST._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2.UPST.DWN1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2.UPST.DWN2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3.UPST.DWN2.BCOM._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3.UPST.DWN3.BCOM._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3.UPST.DWN4.BCOM._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3.UPST.DWN5.BCOM._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4.UPST.DWNB._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4.UPST.DWNC._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX6.UPST.DWNB._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX6.UPST.DWNC._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.SBEX._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.COMP._PRT]
ACPI: PCI Interrupt Link [LK00] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LK01] (IRQs 3 4 5 6 7 *10 11 12)
ACPI: PCI Interrupt Link [LK02] (IRQs 3 4 5 *6 7 10 11 12)
ACPI: PCI Interrupt Link [LK03] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LK04] (IRQs 3 4 *5 6 7 10 11 12)
ACPI: PCI Interrupt Link [LK05] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LK06] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LK07] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
Switched to high resolution mode on CPU 0
Switched to high resolution mode on CPU 2
Switched to high resolution mode on CPU 4
Switched to high resolution mode on CPU 14
Switched to high resolution mode on CPU 7
Switched to high resolution mode on CPU 12
Switched to high resolution mode on CPU 13
Switched to high resolution mode on CPU 11
Switched to high resolution mode on CPU 3
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 5
Switched to high resolution mode on CPU 10
Switched to high resolution mode on CPU 9
Switched to high resolution mode on CPU 8
Switched to high resolution mode on CPU 15
Switched to high resolution mode on CPU 6
system 00:07: ioport range 0x800-0x87f has been reserved
system 00:07: ioport range 0x880-0x8bf has been reserved
system 00:07: ioport range 0x8c0-0x8df has been reserved
system 00:07: ioport range 0x8e0-0x8e3 has been reserved
system 00:07: ioport range 0x8f0-0x8f1 has been reserved
system 00:07: ioport range 0x900-0x900 has been reserved
system 00:07: ioport range 0xc00-0xc7f has been reserved
system 00:07: ioport range 0xca0-0xca7 has been reserved
system 00:07: ioport range 0xca9-0xcab has been reserved
system 00:07: ioport range 0xcad-0xcaf has been reserved
system 00:08: ioport range 0xca8-0xca8 has been reserved
system 00:08: ioport range 0xcac-0xcac has been reserved
system 00:09: iomem range 0xe0000000-0xefffffff could not be reserved
pci 0000:00:01.0: PCI bridge, secondary bus 0000:14
pci 0000:00:01.0:   IO window: disabled
pci 0000:00:01.0:   MEM window: disabled
pci 0000:00:01.0:   PREFETCH window: disabled
pci 0000:17:00.0: PCI bridge, secondary bus 0000:19
pci 0000:17:00.0:   IO window: 0xe000-0xefff
pci 0000:17:00.0:   MEM window: 0xde200000-0xde3fffff
pci 0000:17:00.0:   PREFETCH window: disabled
pci 0000:17:01.0: PCI bridge, secondary bus 0000:18
pci 0000:17:01.0:   IO window: disabled
pci 0000:17:01.0:   MEM window: disabled
pci 0000:17:01.0:   PREFETCH window: disabled
pci 0000:16:00.0: PCI bridge, secondary bus 0000:17
pci 0000:16:00.0:   IO window: 0xe000-0xefff
pci 0000:16:00.0:   MEM window: 0xde200000-0xde3fffff
pci 0000:16:00.0:   PREFETCH window: disabled
pci 0000:16:00.3: PCI bridge, secondary bus 0000:1a
pci 0000:16:00.3:   IO window: disabled
pci 0000:16:00.3:   MEM window: disabled
pci 0000:16:00.3:   PREFETCH window: disabled
pci 0000:00:02.0: PCI bridge, secondary bus 0000:16
pci 0000:00:02.0:   IO window: 0xe000-0xefff
pci 0000:00:02.0:   MEM window: 0xde100000-0xde3fffff
pci 0000:00:02.0:   PREFETCH window: disabled
pci 0000:02:01.0: PCI bridge, secondary bus 0000:03
pci 0000:02:01.0:   IO window: disabled
pci 0000:02:01.0:   MEM window: disabled
pci 0000:02:01.0:   PREFETCH window: disabled
pci 0000:0a:00.0: PCI bridge, secondary bus 0000:0b
pci 0000:0a:00.0:   IO window: disabled
pci 0000:0a:00.0:   MEM window: 0xd6000000-0xd7ffffff
pci 0000:0a:00.0:   PREFETCH window: disabled
pci 0000:02:02.0: PCI bridge, secondary bus 0000:0a
pci 0000:02:02.0:   IO window: disabled
pci 0000:02:02.0:   MEM window: 0xd6000000-0xd7ffffff
pci 0000:02:02.0:   PREFETCH window: disabled
pci 0000:08:00.0: PCI bridge, secondary bus 0000:09
pci 0000:08:00.0:   IO window: disabled
pci 0000:08:00.0:   MEM window: 0xd8000000-0xd9ffffff
pci 0000:08:00.0:   PREFETCH window: disabled
pci 0000:02:03.0: PCI bridge, secondary bus 0000:08
pci 0000:02:03.0:   IO window: disabled
pci 0000:02:03.0:   MEM window: 0xd8000000-0xd9ffffff
pci 0000:02:03.0:   PREFETCH window: disabled
pci 0000:06:00.0: PCI bridge, secondary bus 0000:07
pci 0000:06:00.0:   IO window: disabled
pci 0000:06:00.0:   MEM window: 0xda000000-0xdbffffff
pci 0000:06:00.0:   PREFETCH window: disabled
pci 0000:02:04.0: PCI bridge, secondary bus 0000:06
pci 0000:02:04.0:   IO window: disabled
pci 0000:02:04.0:   MEM window: 0xda000000-0xdbffffff
pci 0000:02:04.0:   PREFETCH window: disabled
pci 0000:04:00.0: PCI bridge, secondary bus 0000:05
pci 0000:04:00.0:   IO window: disabled
pci 0000:04:00.0:   MEM window: 0xdc000000-0xddffffff
pci 0000:04:00.0:   PREFETCH window: disabled
pci 0000:02:05.0: PCI bridge, secondary bus 0000:04
pci 0000:02:05.0:   IO window: disabled
pci 0000:02:05.0:   MEM window: 0xdc000000-0xddffffff
pci 0000:02:05.0:   PREFETCH window: disabled
pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
pci 0000:01:00.0:   IO window: disabled
pci 0000:01:00.0:   MEM window: 0xd6000000-0xddffffff
pci 0000:01:00.0:   PREFETCH window: disabled
pci 0000:00:03.0: PCI bridge, secondary bus 0000:01
pci 0000:00:03.0:   IO window: disabled
pci 0000:00:03.0:   MEM window: 0xd6000000-0xddffffff
pci 0000:00:03.0:   PREFETCH window: disabled
pci 0000:0d:02.0: PCI bridge, secondary bus 0000:0f
pci 0000:0d:02.0:   IO window: disabled
pci 0000:0d:02.0:   MEM window: disabled
pci 0000:0d:02.0:   PREFETCH window: disabled
pci 0000:0d:04.0: PCI bridge, secondary bus 0000:0e
pci 0000:0d:04.0:   IO window: disabled
pci 0000:0d:04.0:   MEM window: disabled
pci 0000:0d:04.0:   PREFETCH window: disabled
pci 0000:0c:00.0: PCI bridge, secondary bus 0000:0d
pci 0000:0c:00.0:   IO window: disabled
pci 0000:0c:00.0:   MEM window: disabled
pci 0000:0c:00.0:   PREFETCH window: disabled
pci 0000:00:04.0: PCI bridge, secondary bus 0000:0c
pci 0000:00:04.0:   IO window: disabled
pci 0000:00:04.0:   MEM window: disabled
pci 0000:00:04.0:   PREFETCH window: disabled
pci 0000:11:02.0: PCI bridge, secondary bus 0000:13
pci 0000:11:02.0:   IO window: disabled
pci 0000:11:02.0:   MEM window: disabled
pci 0000:11:02.0:   PREFETCH window: disabled
pci 0000:11:04.0: PCI bridge, secondary bus 0000:12
pci 0000:11:04.0:   IO window: disabled
pci 0000:11:04.0:   MEM window: disabled
pci 0000:11:04.0:   PREFETCH window: disabled
pci 0000:10:00.0: PCI bridge, secondary bus 0000:11
pci 0000:10:00.0:   IO window: disabled
pci 0000:10:00.0:   MEM window: disabled
pci 0000:10:00.0:   PREFETCH window: disabled
pci 0000:00:06.0: PCI bridge, secondary bus 0000:10
pci 0000:00:06.0:   IO window: disabled
pci 0000:00:06.0:   MEM window: disabled
pci 0000:00:06.0:   PREFETCH window: disabled
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:15
pci 0000:00:1c.0:   IO window: disabled
pci 0000:00:1c.0:   MEM window: disabled
pci 0000:00:1c.0:   PREFETCH window: disabled
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:1b
pci 0000:00:1e.0:   IO window: 0xd000-0xdfff
pci 0000:00:1e.0:   MEM window: 0xde400000-0xde4fffff
pci 0000:00:1e.0:   PREFETCH window: 0x000000c8000000-0x000000cfffffff
pci 0000:00:01.0: PCI INT A -> GSI 36 (level, low) -> IRQ 36
pci 0000:00:01.0: setting latency timer to 64
pci 0000:00:02.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:02.0: setting latency timer to 64
pci 0000:16:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:16:00.0: setting latency timer to 64
pci 0000:17:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:17:00.0: setting latency timer to 64
pci 0000:17:01.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
pci 0000:17:01.0: setting latency timer to 64
pci 0000:16:00.3: setting latency timer to 64
pci 0000:00:03.0: PCI INT A -> GSI 37 (level, low) -> IRQ 37
pci 0000:00:03.0: setting latency timer to 64
pci 0000:01:00.0: setting latency timer to 64
pci 0000:02:01.0: setting latency timer to 64
pci 0000:02:02.0: setting latency timer to 64
pci 0000:0a:00.0: setting latency timer to 64
pci 0000:02:03.0: setting latency timer to 64
pci 0000:08:00.0: setting latency timer to 64
pci 0000:02:04.0: setting latency timer to 64
pci 0000:06:00.0: setting latency timer to 64
pci 0000:02:05.0: setting latency timer to 64
pci 0000:04:00.0: setting latency timer to 64
pci 0000:00:04.0: PCI INT A -> GSI 32 (level, low) -> IRQ 32
pci 0000:00:04.0: setting latency timer to 64
pci 0000:0c:00.0: setting latency timer to 64
pci 0000:0d:02.0: setting latency timer to 64
pci 0000:0d:04.0: setting latency timer to 64
pci 0000:00:06.0: PCI INT A -> GSI 33 (level, low) -> IRQ 33
pci 0000:00:06.0: setting latency timer to 64
pci 0000:10:00.0: setting latency timer to 64
pci 0000:11:02.0: setting latency timer to 64
pci 0000:11:04.0: setting latency timer to 64
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
highmem bounce pool size: 64 pages
HugeTLB registered 2 MB page size, pre-allocated 0 pages
msgmni has been set to 1235
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered (default)
pci 0000:1b:0c.0: Boot video device
pcieport-driver 0000:00:01.0: setting latency timer to 64
pcieport-driver 0000:00:01.0: found MSI capability
pci_express 0000:00:01.0:pcie00: allocate port service
pcieport-driver 0000:00:02.0: setting latency timer to 64
pcieport-driver 0000:00:02.0: found MSI capability
pci_express 0000:00:02.0:pcie00: allocate port service
pcieport-driver 0000:00:03.0: setting latency timer to 64
pcieport-driver 0000:00:03.0: found MSI capability
pci_express 0000:00:03.0:pcie00: allocate port service
pcieport-driver 0000:00:04.0: setting latency timer to 64
pcieport-driver 0000:00:04.0: found MSI capability
pci_express 0000:00:04.0:pcie00: allocate port service
pcieport-driver 0000:00:06.0: setting latency timer to 64
pcieport-driver 0000:00:06.0: found MSI capability
pci_express 0000:00:06.0:pcie00: allocate port service
pcieport-driver 0000:00:1c.0: setting latency timer to 64
pcieport-driver 0000:00:1c.0: found MSI capability
pci_express 0000:00:1c.0:pcie00: allocate port service
pci_express 0000:00:1c.0:pcie02: allocate port service
pcieport-driver 0000:01:00.0: setting latency timer to 64
pcieport-driver 0000:02:01.0: setting latency timer to 64
pcieport-driver 0000:02:01.0: found MSI capability
pcieport-driver 0000:02:02.0: setting latency timer to 64
pcieport-driver 0000:02:02.0: found MSI capability
pcieport-driver 0000:02:03.0: setting latency timer to 64
pcieport-driver 0000:02:03.0: found MSI capability
pcieport-driver 0000:02:04.0: setting latency timer to 64
pcieport-driver 0000:02:04.0: found MSI capability
pcieport-driver 0000:02:05.0: setting latency timer to 64
pcieport-driver 0000:02:05.0: found MSI capability
pcieport-driver 0000:0c:00.0: setting latency timer to 64
pcieport-driver 0000:0d:02.0: setting latency timer to 64
pcieport-driver 0000:0d:02.0: found MSI capability
pcieport-driver 0000:0d:04.0: setting latency timer to 64
pcieport-driver 0000:0d:04.0: found MSI capability
pcieport-driver 0000:10:00.0: setting latency timer to 64
pcieport-driver 0000:11:02.0: setting latency timer to 64
pcieport-driver 0000:11:02.0: found MSI capability
pcieport-driver 0000:11:04.0: setting latency timer to 64
pcieport-driver 0000:11:04.0: found MSI capability
pcieport-driver 0000:16:00.0: setting latency timer to 64
pcieport-driver 0000:17:00.0: setting latency timer to 64
pcieport-driver 0000:17:00.0: found MSI capability
pcieport-driver 0000:17:01.0: setting latency timer to 64
pcieport-driver 0000:17:01.0: found MSI capability
input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
ACPI: Power Button (FF) [PWRF]
processor ACPI0007:00: registered as cooling_device0
processor ACPI0007:01: registered as cooling_device1
processor ACPI0007:02: registered as cooling_device2
processor ACPI0007:03: registered as cooling_device3
processor ACPI0007:04: registered as cooling_device4
processor ACPI0007:05: registered as cooling_device5
processor ACPI0007:06: registered as cooling_device6
processor ACPI0007:07: registered as cooling_device7
processor ACPI0007:08: registered as cooling_device8
processor ACPI0007:09: registered as cooling_device9
processor ACPI0007:0a: registered as cooling_device10
processor ACPI0007:0b: registered as cooling_device11
processor ACPI0007:0c: registered as cooling_device12
processor ACPI0007:0d: registered as cooling_device13
processor ACPI0007:0e: registered as cooling_device14
processor ACPI0007:0f: registered as cooling_device15
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.103
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
pcnet32.c:v1.35 21.Apr.2008 tsbogend@alpha.franken.de
Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.7.9 (July 18, 2008)
bnx2 0000:05:00.0: PCI INT A -> GSI 38 (level, low) -> IRQ 38
eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem dc000000, IRQ 38, node addr 00:1e:c9:d9:84:57
bnx2 0000:07:00.0: PCI INT A -> GSI 37 (level, low) -> IRQ 37
eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem da000000, IRQ 37, node addr 00:1e:c9:d9:84:59
bnx2 0000:09:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
eth2: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem d8000000, IRQ 19, node addr 00:1e:c9:d9:84:5b
bnx2 0000:0b:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
eth3: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem d6000000, IRQ 18, node addr 00:1e:c9:d9:84:5d
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
Uniform Multi-Platform E-IDE driver
ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports
Probing IDE interface ide0...
hda: TSSTcorpDVD-ROM TS-L333A, ATAPI CD/DVD-ROM drive
Probing IDE interface ide1...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
megasas: 00.00.03.20-rc1 Mon. March 10 11:02:31 PDT 2008
megasas: 0x1000:0x0060:0x1028:0x1f0c: bus 25:slot 0:func 0
megaraid_sas 0000:19:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
megaraid_sas 0000:19:00.0: setting latency timer to 64
megasas: FW now in Ready state
scsi0 : LSI SAS based MegaRAID driver
scsi 0:0:0:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:1:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:2:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:3:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:4:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:5:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:6:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:7:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:32:0: Enclosure         DP       BACKPLANE        1.06 PQ: 0 ANSI: 5
scsi 0:2:0:0: Direct-Access     DELL     PERC 6/i         1.11 PQ: 0 ANSI: 5
Driver 'sd' needs updating - please use bus_type methods
sd 0:2:0:0: [sda] 710410240 512-byte hardware sectors (363730 MB)
sd 0:2:0:0: [sda] Write Protect is off
sd 0:2:0:0: [sda] Mode Sense: 1f 00 00 08
sd 0:2:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:2:0:0: [sda] 710410240 512-byte hardware sectors (363730 MB)
sd 0:2:0:0: [sda] Write Protect is off
sd 0:2:0:0: [sda] Mode Sense: 1f 00 00 08
sd 0:2:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 sda13 sda14 sda15 >
sd 0:2:0:0: [sda] Attached SCSI disk
ata_piix 0000:00:1f.2: version 2.12
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
ata_piix 0000:00:1f.2: BAR 0: can't reserve I/O region [0x1f0-0x1f7]
ata_piix 0000:00:1f.2: failed to request/iomap BARs for port 0 (errno=-16)
ata_piix 0000:00:1f.2: BAR 2: can't reserve I/O region [0x170-0x177]
ata_piix 0000:00:1f.2: failed to request/iomap BARs for port 1 (errno=-16)
ata_piix 0000:00:1f.2: no available native port
Fusion MPT base driver 3.04.07
Copyright (c) 1999-2008 LSI Corporation
Fusion MPT SPI Host driver 3.04.07
ehci_hcd 0000:00:1d.7: PCI INT B -> GSI 21 (level, low) -> IRQ 21
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 21, io mem 0xde0ffc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.27-rc3 ehci_hcd
usb usb1: SerialNumber: 0000:00:1d.7
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
USB Universal Host Controller Interface driver v3.0
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 20, io base 0x0000cc80
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb 1-2: new high speed USB device using ehci_hcd and address 2
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.27-rc3 uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.0
uhci_hcd 0000:00:1d.1: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 20, io base 0x0000cca0
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 1-2: configuration #1 chosen from 1 choice
hub 1-2:1.0: USB hub found
hub 1-2:1.0: 2 ports detected
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.27-rc3 uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.1
uhci_hcd 0000:00:1d.2: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 20, io base 0x0000ccc0
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-2: New USB device found, idVendor=413c, idProduct=a001
usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.27-rc3 uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.2
uhci_hcd 0000:00:1d.3: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1d.3: setting latency timer to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 20, io base 0x0000cce0
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 1-7: new high speed USB device using ehci_hcd and address 4
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.27-rc3 uhci_hcd
usb usb5: SerialNumber: 0000:00:1d.3
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
usb 1-7: configuration #1 chosen from 1 choice
hub 1-7:1.0: USB hub found
hub 1-7:1.0: 2 ports detected
input: PC Speaker as /devices/platform/pcspkr/input/input1
coretemp coretemp.0: Using relative temperature scale!
coretemp coretemp.1: Using relative temperature scale!
coretemp coretemp.2: Using relative temperature scale!
coretemp coretemp.3: Using relative temperature scale!
coretemp coretemp.4: Using relative temperature scale!
coretemp coretemp.5: Using relative temperature scale!
coretemp coretemp.6: Using relative temperature scale!
coretemp coretemp.7: Using relative temperature scale!
coretemp coretemp.8: Using relative temperature scale!
coretemp coretemp.9: Using relative temperature scale!
coretemp coretemp.10: Using relative temperature scale!
coretemp coretemp.11: Using relative temperature scale!
coretemp coretemp.12: Using relative temperature scale!
coretemp coretemp.13: Using relative temperature scale!
coretemp coretemp.14: Using relative temperature scale!
coretemp coretemp.15: Using relative temperature scale!
hdaps: supported laptop not found!
hdaps: driver init failed (ret=-19)!
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
EDAC MC: Ver: 2.1.0 Aug 14 2008
usb 1-7: New USB device found, idVendor=04b4, idProduct=6560
usb 1-7: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 3-1: new low speed USB device using uhci_hcd and address 2
usb 3-1: configuration #1 chosen from 1 choice
usb 3-1: New USB device found, idVendor=0624, idProduct=0294
usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 3-1: Product: Dell 03R874
usb 3-1: Manufacturer: Avocent
usb 1-2.1: new full speed USB device using ehci_hcd and address 5
usb 1-2.1: configuration #1 chosen from 1 choice
usb 1-2.1: New USB device found, idVendor=413c, idProduct=0000
usb 1-2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-2.1: Product: DRAC5
usb 1-2.1: Manufacturer: Dell
usb 1-2.1: SerialNumber: 0000000
usb 1-7.1: new high speed USB device using ehci_hcd and address 6
usb 1-7.1: configuration #1 chosen from 1 choice
hub 1-7.1:1.0: USB hub found
hub 1-7.1:1.0: 2 ports detected
usb 1-7.1: New USB device found, idVendor=04b4, idProduct=6560
usb 1-7.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usbcore: registered new interface driver hiddev
input: Avocent Dell 03R874 as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input2
input: USB HID v1.10 Keyboard [Avocent Dell 03R874] on usb-0000:00:1d.1-1
input: Avocent Dell 03R874 as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.1/input/input3
input: USB HID v1.10 Mouse [Avocent Dell 03R874] on usb-0000:00:1d.1-1
input: Dell DRAC5 as /devices/pci0000:00/0000:00:1d.7/usb1/1-2/1-2.1/1-2.1:1.0/input/input4
input: USB HID v1.10 Keyboard [Dell DRAC5] on usb-0000:00:1d.7-2.1
input: Dell DRAC5 as /devices/pci0000:00/0000:00:1d.7/usb1/1-2/1-2.1/1-2.1:1.1/input/input5
input: USB HID v1.10 Mouse [Dell DRAC5] on usb-0000:00:1d.7-2.1
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.17.
ALSA device list:
  No soundcards found.
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 17
Starting balanced_irq
Using IPI No-Shortcut mode
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 260k freed
Adding 27350652k swap on /dev/sda3.  Priority:-1 extents:1 across:27350652k
bnx2: eth0: using MSI
bnx2: eth1: using MSI
bnx2: eth0 NIC Copper Link is Up, 1000 Mbps full duplex

[-- Attachment #5: Type: TEXT/PLAIN, Size: 31517 bytes --]

1861.913 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 33263208k/35651584k available (2653k kernel code, 284596k reserved, 1242k data, 260k init, 32631496k highmem)
virtual kernel memory layout:
    fixmap  : 0xffee9000 - 0xfffff000   (1112 kB)
    pkmap   : 0xffa00000 - 0xffc00000   (2048 kB)
    vmalloc : 0xf8800000 - 0xff9fe000   ( 113 MB)
    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
      .init : 0xc04d2000 - 0xc0513000   ( 260 kB)
      .data : 0xc039762b - 0xc04cde88   (1242 kB)
      .text : 0xc0100000 - 0xc039762b   (2653 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
CPA: page pool initialized 1 of 1 pages preallocated
SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=16, Nodes=1
hpet clockevent registered
Calibrating delay loop (skipped), value calculated using timer frequency.. 3723.82 BogoMIPS (lpj=7447652)
Mount-cache hash table entries: 512
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
using mwait in idle threads.
Checking 'hlt' instruction... OK.
ACPI: Core revision 20080609
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
CPU 1 irqstacks, hard=c0527000 soft=c0517000
Booting processor 1/8 ip 6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3723.89 BogoMIPS (lpj=7447783)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 0
CPU1: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
More than 8 CPUs detected - skipping them.
Use CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP.
More than 8 CPUs detected - skipping them.
Use CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP.
CPU 4 irqstacks, hard=c052a000 soft=c051a000
Booting processor 4/2 ip 6000
Initializing CPU#4
Calibrating delay using timer specific routine.. 3723.86 BogoMIPS (lpj=7447723)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 2
CPU4: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#4]: passed.
More than 8 CPUs detected - skipping them.
Use CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP.
More than 8 CPUs detected - skipping them.
Use CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP.
More than 8 CPUs detected - skipping them.
Use CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP.
Brought up 3 CPUs
Total of 3 processors activated (11171.57 BogoMIPS).
net_namespace: 596 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
No dock devices found.
ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
ACPI: bus type pci registered
PCI: Using configuration type 1 for base access
PCI: Dell PowerEdge R900 detected, enabling pci=bfsort.
ACPI: EC: Look up EC in DSDT
ACPI: BIOS _OSI(Linux) query ignored
ACPI: DMI System Vendor: Dell Inc.
ACPI: DMI Product Name: PowerEdge R900
ACPI: DMI Product Version: 
ACPI: DMI Board Name: 0C764H
ACPI: DMI BIOS Vendor: Dell Inc.
ACPI: DMI BIOS Date: 03/23/2008
ACPI: Please send DMI info above to linux-acpi@vger.kernel.org
ACPI: If "acpi_osi=Linux" works better, please notify linux-acpi@vger.kernel.org
ACPI: Interpreter enabled
ACPI: (supports S0 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
pci 0000:00:00.0: PME# disabled
pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
pci 0000:00:01.0: PME# disabled
pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
pci 0000:00:02.0: PME# disabled
pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
pci 0000:00:03.0: PME# disabled
pci 0000:00:04.0: PME# supported from D0 D3hot D3cold
pci 0000:00:04.0: PME# disabled
pci 0000:00:06.0: PME# supported from D0 D3hot D3cold
pci 0000:00:06.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:16:00.0: PME# supported from D0 D3hot D3cold
pci 0000:16:00.0: PME# disabled
pci 0000:16:00.3: PME# supported from D0 D3hot D3cold
pci 0000:16:00.3: PME# disabled
pci 0000:17:00.0: PME# supported from D0 D3hot D3cold
pci 0000:17:00.0: PME# disabled
pci 0000:17:01.0: PME# supported from D0 D3hot D3cold
pci 0000:17:01.0: PME# disabled
pci 0000:19:00.0: supports D1
pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
pci 0000:01:00.0: PME# disabled
pci 0000:02:01.0: PME# supported from D0 D3hot D3cold
pci 0000:02:01.0: PME# disabled
pci 0000:02:02.0: PME# supported from D0 D3hot D3cold
pci 0000:02:02.0: PME# disabled
pci 0000:02:03.0: PME# supported from D0 D3hot D3cold
pci 0000:02:03.0: PME# disabled
pci 0000:02:04.0: PME# supported from D0 D3hot D3cold
pci 0000:02:04.0: PME# disabled
pci 0000:02:05.0: PME# supported from D0 D3hot D3cold
pci 0000:02:05.0: PME# disabled
pci 0000:0a:00.0: PME# supported from D0 D3hot D3cold
pci 0000:0a:00.0: PME# disabled
pci 0000:0b:00.0: PME# supported from D3hot D3cold
pci 0000:0b:00.0: PME# disabled
pci 0000:08:00.0: PME# supported from D0 D3hot D3cold
pci 0000:08:00.0: PME# disabled
pci 0000:09:00.0: PME# supported from D3hot D3cold
pci 0000:09:00.0: PME# disabled
pci 0000:06:00.0: PME# supported from D0 D3hot D3cold
pci 0000:06:00.0: PME# disabled
pci 0000:07:00.0: PME# supported from D3hot D3cold
pci 0000:07:00.0: PME# disabled
pci 0000:04:00.0: PME# supported from D0 D3hot D3cold
pci 0000:04:00.0: PME# disabled
pci 0000:05:00.0: PME# supported from D3hot D3cold
pci 0000:05:00.0: PME# disabled
pci 0000:0c:00.0: PME# supported from D0 D3hot D3cold
pci 0000:0c:00.0: PME# disabled
pci 0000:0d:02.0: PME# supported from D0 D3hot D3cold
pci 0000:0d:02.0: PME# disabled
pci 0000:0d:04.0: PME# supported from D0 D3hot D3cold
pci 0000:0d:04.0: PME# disabled
pci 0000:10:00.0: PME# supported from D0 D3hot D3cold
pci 0000:10:00.0: PME# disabled
pci 0000:11:02.0: PME# supported from D0 D3hot D3cold
pci 0000:11:02.0: PME# disabled
pci 0000:11:04.0: PME# supported from D0 D3hot D3cold
pci 0000:11:04.0: PME# disabled
pci 0000:1b:0c.0: supports D1
pci 0000:1b:0c.0: supports D2
pci 0000:00:1e.0: transparent bridge
bus 00 -> node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2.UPST._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2.UPST.DWN1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2.UPST.DWN2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3.UPST.DWN2.BCOM._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3.UPST.DWN3.BCOM._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3.UPST.DWN4.BCOM._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3.UPST.DWN5.BCOM._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4.UPST.DWNB._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4.UPST.DWNC._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX6.UPST.DWNB._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX6.UPST.DWNC._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.SBEX._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.COMP._PRT]
ACPI: PCI Interrupt Link [LK00] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LK01] (IRQs 3 4 5 6 7 *10 11 12)
ACPI: PCI Interrupt Link [LK02] (IRQs 3 4 5 *6 7 10 11 12)
ACPI: PCI Interrupt Link [LK03] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LK04] (IRQs 3 4 *5 6 7 10 11 12)
ACPI: PCI Interrupt Link [LK05] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LK06] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LK07] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
system 00:07: ioport range 0x800-0x87f has been reserved
system 00:07: ioport range 0x880-0x8bf has been reserved
system 00:07: ioport range 0x8c0-0x8df has been reserved
system 00:07: ioport range 0x8e0-0x8e3 has been reserved
system 00:07: ioport range 0x8f0-0x8f1 has been reserved
system 00:07: ioport range 0x900-0x900 has been reserved
system 00:07: ioport range 0xc00-0xc7f has been reserved
system 00:07: ioport range 0xca0-0xca7 has been reserved
system 00:07: ioport range 0xca9-0xcab has been reserved
system 00:07: ioport range 0xcad-0xcaf has been reserved
system 00:08: ioport range 0xca8-0xca8 has been reserved
system 00:08: ioport range 0xcac-0xcac has been reserved
system 00:09: iomem range 0xe0000000-0xefffffff could not be reserved
pci 0000:00:01.0: PCI bridge, secondary bus 0000:14
pci 0000:00:01.0:   IO window: disabled
pci 0000:00:01.0:   MEM window: disabled
pci 0000:00:01.0:   PREFETCH window: disabled
pci 0000:17:00.0: PCI bridge, secondary bus 0000:19
pci 0000:17:00.0:   IO window: 0xe000-0xefff
pci 0000:17:00.0:   MEM window: 0xde200000-0xde3fffff
pci 0000:17:00.0:   PREFETCH window: disabled
pci 0000:17:01.0: PCI bridge, secondary bus 0000:18
pci 0000:17:01.0:   IO window: disabled
pci 0000:17:01.0:   MEM window: disabled
pci 0000:17:01.0:   PREFETCH window: disabled
pci 0000:16:00.0: PCI bridge, secondary bus 0000:17
pci 0000:16:00.0:   IO window: 0xe000-0xefff
pci 0000:16:00.0:   MEM window: 0xde200000-0xde3fffff
pci 0000:16:00.0:   PREFETCH window: disabled
pci 0000:16:00.3: PCI bridge, secondary bus 0000:1a
pci 0000:16:00.3:   IO window: disabled
pci 0000:16:00.3:   MEM window: disabled
pci 0000:16:00.3:   PREFETCH window: disabled
pci 0000:00:02.0: PCI bridge, secondary bus 0000:16
pci 0000:00:02.0:   IO window: 0xe000-0xefff
pci 0000:00:02.0:   MEM window: 0xde100000-0xde3fffff
pci 0000:00:02.0:   PREFETCH window: disabled
pci 0000:02:01.0: PCI bridge, secondary bus 0000:03
pci 0000:02:01.0:   IO window: disabled
pci 0000:02:01.0:   MEM window: disabled
pci 0000:02:01.0:   PREFETCH window: disabled
pci 0000:0a:00.0: PCI bridge, secondary bus 0000:0b
pci 0000:0a:00.0:   IO window: disabled
pci 0000:0a:00.0:   MEM window: 0xd6000000-0xd7ffffff
pci 0000:0a:00.0:   PREFETCH window: disabled
pci 0000:02:02.0: PCI bridge, secondary bus 0000:0a
pci 0000:02:02.0:   IO window: disabled
pci 0000:02:02.0:   MEM window: 0xd6000000-0xd7ffffff
pci 0000:02:02.0:   PREFETCH window: disabled
pci 0000:08:00.0: PCI bridge, secondary bus 0000:09
pci 0000:08:00.0:   IO window: disabled
pci 0000:08:00.0:   MEM window: 0xd8000000-0xd9ffffff
pci 0000:08:00.0:   PREFETCH window: disabled
pci 0000:02:03.0: PCI bridge, secondary bus 0000:08
pci 0000:02:03.0:   IO window: disabled
pci 0000:02:03.0:   MEM window: 0xd8000000-0xd9ffffff
pci 0000:02:03.0:   PREFETCH window: disabled
pci 0000:06:00.0: PCI bridge, secondary bus 0000:07
pci 0000:06:00.0:   IO window: disabled
pci 0000:06:00.0:   MEM window: 0xda000000-0xdbffffff
pci 0000:06:00.0:   PREFETCH window: disabled
pci 0000:02:04.0: PCI bridge, secondary bus 0000:06
pci 0000:02:04.0:   IO window: disabled
pci 0000:02:04.0:   MEM window: 0xda000000-0xdbffffff
pci 0000:02:04.0:   PREFETCH window: disabled
pci 0000:04:00.0: PCI bridge, secondary bus 0000:05
pci 0000:04:00.0:   IO window: disabled
pci 0000:04:00.0:   MEM window: 0xdc000000-0xddffffff
pci 0000:04:00.0:   PREFETCH window: disabled
pci 0000:02:05.0: PCI bridge, secondary bus 0000:04
pci 0000:02:05.0:   IO window: disabled
pci 0000:02:05.0:   MEM window: 0xdc000000-0xddffffff
pci 0000:02:05.0:   PREFETCH window: disabled
pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
pci 0000:01:00.0:   IO window: disabled
pci 0000:01:00.0:   MEM window: 0xd6000000-0xddffffff
pci 0000:01:00.0:   PREFETCH window: disabled
pci 0000:00:03.0: PCI bridge, secondary bus 0000:01
pci 0000:00:03.0:   IO window: disabled
pci 0000:00:03.0:   MEM window: 0xd6000000-0xddffffff
pci 0000:00:03.0:   PREFETCH window: disabled
pci 0000:0d:02.0: PCI bridge, secondary bus 0000:0f
pci 0000:0d:02.0:   IO window: disabled
pci 0000:0d:02.0:   MEM window: disabled
pci 0000:0d:02.0:   PREFETCH window: disabled
pci 0000:0d:04.0: PCI bridge, secondary bus 0000:0e
pci 0000:0d:04.0:   IO window: disabled
pci 0000:0d:04.0:   MEM window: disabled
pci 0000:0d:04.0:   PREFETCH window: disabled
pci 0000:0c:00.0: PCI bridge, secondary bus 0000:0d
pci 0000:0c:00.0:   IO window: disabled
pci 0000:0c:00.0:   MEM window: disabled
pci 0000:0c:00.0:   PREFETCH window: disabled
pci 0000:00:04.0: PCI bridge, secondary bus 0000:0c
pci 0000:00:04.0:   IO window: disabled
pci 0000:00:04.0:   MEM window: disabled
pci 0000:00:04.0:   PREFETCH window: disabled
pci 0000:11:02.0: PCI bridge, secondary bus 0000:13
pci 0000:11:02.0:   IO window: disabled
pci 0000:11:02.0:   MEM window: disabled
pci 0000:11:02.0:   PREFETCH window: disabled
pci 0000:11:04.0: PCI bridge, secondary bus 0000:12
pci 0000:11:04.0:   IO window: disabled
pci 0000:11:04.0:   MEM window: disabled
pci 0000:11:04.0:   PREFETCH window: disabled
pci 0000:10:00.0: PCI bridge, secondary bus 0000:11
pci 0000:10:00.0:   IO window: disabled
pci 0000:10:00.0:   MEM window: disabled
pci 0000:10:00.0:   PREFETCH window: disabled
pci 0000:00:06.0: PCI bridge, secondary bus 0000:10
pci 0000:00:06.0:   IO window: disabled
pci 0000:00:06.0:   MEM window: disabled
pci 0000:00:06.0:   PREFETCH window: disabled
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:15
pci 0000:00:1c.0:   IO window: disabled
pci 0000:00:1c.0:   MEM window: disabled
pci 0000:00:1c.0:   PREFETCH window: disabled
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:1b
pci 0000:00:1e.0:   IO window: 0xd000-0xdfff
pci 0000:00:1e.0:   MEM window: 0xde400000-0xde4fffff
pci 0000:00:1e.0:   PREFETCH window: 0x000000c8000000-0x000000cfffffff
pci 0000:00:01.0: PCI INT A -> GSI 36 (level, low) -> IRQ 36
pci 0000:00:01.0: setting latency timer to 64
pci 0000:00:02.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:02.0: setting latency timer to 64
pci 0000:16:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:16:00.0: setting latency timer to 64
pci 0000:17:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:17:00.0: setting latency timer to 64
pci 0000:17:01.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
pci 0000:17:01.0: setting latency timer to 64
pci 0000:16:00.3: setting latency timer to 64
pci 0000:00:03.0: PCI INT A -> GSI 37 (level, low) -> IRQ 37
pci 0000:00:03.0: setting latency timer to 64
pci 0000:01:00.0: setting latency timer to 64
pci 0000:02:01.0: setting latency timer to 64
pci 0000:02:02.0: setting latency timer to 64
pci 0000:0a:00.0: setting latency timer to 64
pci 0000:02:03.0: setting latency timer to 64
pci 0000:08:00.0: setting latency timer to 64
pci 0000:02:04.0: setting latency timer to 64
pci 0000:06:00.0: setting latency timer to 64
pci 0000:02:05.0: setting latency timer to 64
pci 0000:04:00.0: setting latency timer to 64
pci 0000:00:04.0: PCI INT A -> GSI 32 (level, low) -> IRQ 32
pci 0000:00:04.0: setting latency timer to 64
pci 0000:0c:00.0: setting latency timer to 64
pci 0000:0d:02.0: setting latency timer to 64
pci 0000:0d:04.0: setting latency timer to 64
pci 0000:00:06.0: PCI INT A -> GSI 33 (level, low) -> IRQ 33
pci 0000:00:06.0: setting latency timer to 64
pci 0000:10:00.0: setting latency timer to 64
pci 0000:11:02.0: setting latency timer to 64
pci 0000:11:04.0: setting latency timer to 64
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 4
Switched to high resolution mode on CPU 0
NET: Registered protocol family 1
highmem bounce pool size: 64 pages
HugeTLB registered 2 MB page size, pre-allocated 0 pages
msgmni has been set to 1235
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered (default)
pci 0000:1b:0c.0: Boot video device
pcieport-driver 0000:00:01.0: setting latency timer to 64
pcieport-driver 0000:00:01.0: found MSI capability
pci_express 0000:00:01.0:pcie00: allocate port service
pcieport-driver 0000:00:02.0: setting latency timer to 64
pcieport-driver 0000:00:02.0: found MSI capability
pci_express 0000:00:02.0:pcie00: allocate port service
pcieport-driver 0000:00:03.0: setting latency timer to 64
pcieport-driver 0000:00:03.0: found MSI capability
pci_express 0000:00:03.0:pcie00: allocate port service
pcieport-driver 0000:00:04.0: setting latency timer to 64
pcieport-driver 0000:00:04.0: found MSI capability
pci_express 0000:00:04.0:pcie00: allocate port service
pcieport-driver 0000:00:06.0: setting latency timer to 64
pcieport-driver 0000:00:06.0: found MSI capability
pci_express 0000:00:06.0:pcie00: allocate port service
pcieport-driver 0000:00:1c.0: setting latency timer to 64
pcieport-driver 0000:00:1c.0: found MSI capability
pci_express 0000:00:1c.0:pcie00: allocate port service
pci_express 0000:00:1c.0:pcie02: allocate port service
pcieport-driver 0000:01:00.0: setting latency timer to 64
pcieport-driver 0000:02:01.0: setting latency timer to 64
pcieport-driver 0000:02:01.0: found MSI capability
pcieport-driver 0000:02:02.0: setting latency timer to 64
pcieport-driver 0000:02:02.0: found MSI capability
pcieport-driver 0000:02:03.0: setting latency timer to 64
pcieport-driver 0000:02:03.0: found MSI capability
pcieport-driver 0000:02:04.0: setting latency timer to 64
pcieport-driver 0000:02:04.0: found MSI capability
pcieport-driver 0000:02:05.0: setting latency timer to 64
pcieport-driver 0000:02:05.0: found MSI capability
pcieport-driver 0000:0c:00.0: setting latency timer to 64
pcieport-driver 0000:0d:02.0: setting latency timer to 64
pcieport-driver 0000:0d:02.0: found MSI capability
pcieport-driver 0000:0d:04.0: setting latency timer to 64
pcieport-driver 0000:0d:04.0: found MSI capability
pcieport-driver 0000:10:00.0: setting latency timer to 64
pcieport-driver 0000:11:02.0: setting latency timer to 64
pcieport-driver 0000:11:02.0: found MSI capability
pcieport-driver 0000:11:04.0: setting latency timer to 64
pcieport-driver 0000:11:04.0: found MSI capability
pcieport-driver 0000:16:00.0: setting latency timer to 64
pcieport-driver 0000:17:00.0: setting latency timer to 64
pcieport-driver 0000:17:00.0: found MSI capability
pcieport-driver 0000:17:01.0: setting latency timer to 64
pcieport-driver 0000:17:01.0: found MSI capability
input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
ACPI: Power Button (FF) [PWRF]
processor ACPI0007:00: registered as cooling_device0
processor ACPI0007:01: registered as cooling_device1
processor ACPI0007:02: registered as cooling_device2
processor ACPI0007:03: registered as cooling_device3
processor ACPI0007:04: registered as cooling_device4
processor ACPI0007:05: registered as cooling_device5
processor ACPI0007:06: registered as cooling_device6
processor ACPI0007:07: registered as cooling_device7
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.103
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
pcnet32.c:v1.35 21.Apr.2008 tsbogend@alpha.franken.de
Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.7.9 (July 18, 2008)
bnx2 0000:05:00.0: PCI INT A -> GSI 38 (level, low) -> IRQ 38
eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem dc000000, IRQ 38, node addr 00:1e:c9:d9:84:57
bnx2 0000:07:00.0: PCI INT A -> GSI 37 (level, low) -> IRQ 37
eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem da000000, IRQ 37, node addr 00:1e:c9:d9:84:59
bnx2 0000:09:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
eth2: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem d8000000, IRQ 19, node addr 00:1e:c9:d9:84:5b
bnx2 0000:0b:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
eth3: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem d6000000, IRQ 18, node addr 00:1e:c9:d9:84:5d
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
Uniform Multi-Platform E-IDE driver
ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports
Probing IDE interface ide0...
hda: TSSTcorpDVD-ROM TS-L333A, ATAPI CD/DVD-ROM drive
Probing IDE interface ide1...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
megasas: 00.00.03.20-rc1 Mon. March 10 11:02:31 PDT 2008
megasas: 0x1000:0x0060:0x1028:0x1f0c: bus 25:slot 0:func 0
megaraid_sas 0000:19:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
megaraid_sas 0000:19:00.0: setting latency timer to 64
megasas: FW now in Ready state
scsi0 : LSI SAS based MegaRAID driver
scsi 0:0:0:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:1:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:2:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:3:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:4:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:5:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:6:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:7:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:32:0: Enclosure         DP       BACKPLANE        1.06 PQ: 0 ANSI: 5
scsi 0:2:0:0: Direct-Access     DELL     PERC 6/i         1.11 PQ: 0 ANSI: 5
Driver 'sd' needs updating - please use bus_type methods
sd 0:2:0:0: [sda] 710410240 512-byte hardware sectors (363730 MB)
sd 0:2:0:0: [sda] Write Protect is off
sd 0:2:0:0: [sda] Mode Sense: 1f 00 00 08
sd 0:2:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:2:0:0: [sda] 710410240 512-byte hardware sectors (363730 MB)
sd 0:2:0:0: [sda] Write Protect is off
sd 0:2:0:0: [sda] Mode Sense: 1f 00 00 08
sd 0:2:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 sda13 sda14 sda15 >
sd 0:2:0:0: [sda] Attached SCSI disk
ata_piix 0000:00:1f.2: version 2.12
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
ata_piix 0000:00:1f.2: BAR 0: can't reserve I/O region [0x1f0-0x1f7]
ata_piix 0000:00:1f.2: failed to request/iomap BARs for port 0 (errno=-16)
ata_piix 0000:00:1f.2: BAR 2: can't reserve I/O region [0x170-0x177]
ata_piix 0000:00:1f.2: failed to request/iomap BARs for port 1 (errno=-16)
ata_piix 0000:00:1f.2: no available native port
Fusion MPT base driver 3.04.07
Copyright (c) 1999-2008 LSI Corporation
Fusion MPT SPI Host driver 3.04.07
ehci_hcd 0000:00:1d.7: PCI INT B -> GSI 21 (level, low) -> IRQ 21
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 21, io mem 0xde0ffc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.27-rc3 ehci_hcd
usb usb1: SerialNumber: 0000:00:1d.7
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
USB Universal Host Controller Interface driver v3.0
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 20, io base 0x0000cc80
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb 1-2: new high speed USB device using ehci_hcd and address 2
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.27-rc3 uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.0
uhci_hcd 0000:00:1d.1: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 20, io base 0x0000cca0
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 1-2: configuration #1 chosen from 1 choice
hub 1-2:1.0: USB hub found
hub 1-2:1.0: 2 ports detected
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.27-rc3 uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.1
uhci_hcd 0000:00:1d.2: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 20, io base 0x0000ccc0
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-2: New USB device found, idVendor=413c, idProduct=a001
usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.27-rc3 uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.2
uhci_hcd 0000:00:1d.3: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1d.3: setting latency timer to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 20, io base 0x0000cce0
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 1-7: new high speed USB device using ehci_hcd and address 4
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.27-rc3 uhci_hcd
usb usb5: SerialNumber: 0000:00:1d.3
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
usb 1-7: configuration #1 chosen from 1 choice
hub 1-7:1.0: USB hub found
hub 1-7:1.0: 2 ports detected
input: PC Speaker as /devices/platform/pcspkr/input/input1
coretemp coretemp.0: Using relative temperature scale!
coretemp coretemp.1: Using relative temperature scale!
coretemp coretemp.4: Using relative temperature scale!
hdaps: supported laptop not found!
hdaps: driver init failed (ret=-19)!
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
EDAC MC: Ver: 2.1.0 Aug 14 2008
usb 1-7: New USB device found, idVendor=04b4, idProduct=6560
usb 1-7: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 3-1: new low speed USB device using uhci_hcd and address 2
usb 3-1: configuration #1 chosen from 1 choice
usb 3-1: New USB device found, idVendor=0624, idProduct=0294
usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 3-1: Product: Dell 03R874
usb 3-1: Manufacturer: Avocent
usbcore: registered new interface driver hiddev
usb 1-2.1: new full speed USB device using ehci_hcd and address 5
usb 1-2.1: configuration #1 chosen from 1 choice
usb 1-2.1: New USB device found, idVendor=413c, idProduct=0000
usb 1-2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-2.1: Product: DRAC5
usb 1-2.1: Manufacturer: Dell
usb 1-2.1: SerialNumber: 0000000
input: Avocent Dell 03R874 as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input2
input: USB HID v1.10 Keyboard [Avocent Dell 03R874] on usb-0000:00:1d.1-1
input: Avocent Dell 03R874 as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.1/input/input3
usb 1-7.1: new high speed USB device using ehci_hcd and address 6
input: USB HID v1.10 Mouse [Avocent Dell 03R874] on usb-0000:00:1d.1-1
input: Dell DRAC5 as /devices/pci0000:00/0000:00:1d.7/usb1/1-2/1-2.1/1-2.1:1.0/input/input4
input: USB HID v1.10 Keyboard [Dell DRAC5] on usb-0000:00:1d.7-2.1
input: Dell DRAC5 as /devices/pci0000:00/0000:00:1d.7/usb1/1-2/1-2.1/1-2.1:1.1/input/input5
input: USB HID v1.10 Mouse [Dell DRAC5] on usb-0000:00:1d.7-2.1
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.17.
ALSA device list:
  No soundcards found.
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 17
Starting balanced_irq
Using IPI No-Shortcut mode
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 260k freed
usb 1-7.1: configuration #1 chosen from 1 choice
hub 1-7.1:1.0: USB hub found
hub 1-7.1:1.0: 2 ports detected
usb 1-7.1: New USB device found, idVendor=04b4, idProduct=6560
usb 1-7.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
Adding 27350652k swap on /dev/sda3.  Priority:-1 extents:1 across:27350652k
hpet1: lost 4 rtc interrupts
bnx2: eth0: using MSI
bnx2: eth1: using MSI
bnx2: eth0 NIC Copper Link is Up, 1000 Mbps full duplex

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Ingo Molnar]

* Jeff Chua <jeff.chua.linux@gmail.com> wrote:

>>> Shall this be put back so that it'll show the message?
>>> -       if (def_to_bigsmp && apicid > 8) {
>>> -               printk(KERN_WARNING
>>> -                       "More than 8 CPUs detected - skipping them.\n"
>>> -                       "Use CONFIG_X86_GENERICARCH and 
> CONFIG_X86_BIGSMP.\n");
>>> -       }
>>
>> could you post the full dmesg? And the modified patch that you've tested
>> to both have 8 CPUs without bigsmp and which also shows the printk?
>>
>>        Ingo
>>
>
> Attached. cpu.8
>    CONFIG_X86_32=y
>    CONFIG_X86_PC=y
>    CONFIG_X86=y
>    CONFIG_NR_CPUS=8
>
> Attached. cpu.16
>    CONFIG_X86_32=y
>    CONFIG_X86_PC=y
>    CONFIG_X86=y
>    CONFIG_NR_CPUS=16
>
> Attached cpu.16.big
>    CONFIG_X86_32=y
>    CONFIG_X86=y
>    CONFIG_X86_GENERICARCH=y
>    CONFIG_X86_BIGSMP=y
>    # CONFIG_X86_PC is not set
>    CONFIG_NR_CPUS=16
>
> Attached cpu.16.nobig (same as cpu.16 except with modifed patch)
>    CONFIG_X86_32=y
>    CONFIG_X86_PC=y
>    CONFIG_X86=y
>    CONFIG_NR_CPUS=16
>
> Attached is the modified patch to make the warning appears. It's 
> Yinghai's patch modified to just display the error and continue to 
> boot.

thanks. To make sure it's all sorted out you might want to boot today's 
tip/master and check whether it just does the right thing by default. 
(it really should)

	Ingo

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Jeff Chua]

[-- Attachment #1: Type: text/plain, Size: 1016 bytes --]

On Fri, Aug 15, 2008 at 10:07 PM, Ingo Molnar <mingo@elte.hu> wrote:

> thanks. To make sure it's all sorted out you might want to boot today's
> tip/master and check whether it just does the right thing by default.
> (it really should)

Yes, verified and it's working now. The warnings show up.

Short dmesg here. Detailed dmesg attached.

Checking 'hlt' instruction... OK.
ACPI: Core revision 20080609
More than 8 CPUs detected - skipping them.
Use CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP.
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
CPU 1 irqstacks, hard=c0527000 soft=c0517000
Booting processor 1/8 ip 6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3723.84 BogoMIPS (lpj=7447688)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 0

Thank you YingHai and Ingo for your great help! Sorry it look at while to reply.

Jeff.

[-- Attachment #2: dmesg.txt --]
[-- Type: text/plain, Size: 39313 bytes --]

Linux version 2.6.27-rc3 (root@boston.corp.fedex.com) (gcc version 4.2.2) #2 SMP PREEMPT Mon Aug 18 10:31:19 SGT 2008
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
 BIOS-e820: 0000000000100000 - 000000007fab0000 (usable)
 BIOS-e820: 000000007fab0000 - 000000007fac4000 (reserved)
 BIOS-e820: 000000007fac4000 - 000000007fac6000 (usable)
 BIOS-e820: 000000007fac6000 - 000000007fad5c00 (ACPI data)
 BIOS-e820: 000000007fad5c00 - 0000000080000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000fe000000 - 0000000100000000 (reserved)
 BIOS-e820: 0000000100000000 - 0000000880000000 (usable)
last_pfn = 0x880000 max_arch_pfn = 0x1000000
kernel direct mapping tables up to 38000000 @ 7000-c000
NX (Execute Disable) protection: active
DMI 2.5 present.
ACPI: RSDP 000F26F0, 0024 (r2 DELL  )
ACPI: XSDT 000F27E8, 007C (r1 DELL   PE_SC3          1 DELL        1)
ACPI: FACP 000F29E0, 00F4 (r3 DELL   PE_SC3          1 DELL        1)
ACPI: DSDT 7FAC6000, 2ECB (r1 DELL   PE_SC3          1 INTL 20050624)
ACPI: FACS 7FAD5C00, 0040
ACPI: APIC 000F2AD4, 015E (r1 DELL   PE_SC3          1 DELL        1)
ACPI: SPCR 000F2C33, 0050 (r1 DELL   PE_SC3          1 DELL        1)
ACPI: HPET 000F2C83, 0038 (r1 DELL   PE_SC3          1 DELL        1)
ACPI: MCFG 000F2CBB, 003C (r1 DELL   PE_SC3          1 DELL        1)
ACPI: SLIC 000F2CF7, 0024 (r1 DELL   PE_SC3          1 DELL        1)
ACPI: ERST 7FAC904C, 0210 (r1 DELL   PE_SC3          1 DELL        1)
ACPI: HEST 7FAC925C, 027C (r1 DELL   PE_SC3          1 DELL        1)
ACPI: BERT 7FAC8ECC, 0030 (r1 DELL   PE_SC3          1 DELL        1)
ACPI: EINJ 7FAC8EFC, 0150 (r1 DELL   PE_SC3          1 DELL        1)
ACPI: TCPA 000F2E79, 0064 (r1 DELL   PE_SC3          1 DELL        1)
33920MB HIGHMEM available.
896MB LOWMEM available.
  mapped low ram: 0 - 38000000
  low ram: 00000000 - 38000000
  bootmap 00008000 - 0000f000
(8 early reservations) ==> bootmem [0000000000 - 0038000000]
  #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
  #1 [0000001000 - 0000002000]    EX TRAMPOLINE ==> [0000001000 - 0000002000]
  #2 [0000006000 - 0000007000]       TRAMPOLINE ==> [0000006000 - 0000007000]
  #3 [0000100000 - 00005dcd28]    TEXT DATA BSS ==> [0000100000 - 00005dcd28]
  #4 [00005dd000 - 00005e5000]    INIT_PG_TABLE ==> [00005dd000 - 00005e5000]
  #5 [000009f000 - 0000100000]    BIOS reserved ==> [000009f000 - 0000100000]
  #6 [0000007000 - 0000008000]          PGTABLE ==> [0000007000 - 0000008000]
  #7 [0000008000 - 000000f000]          BOOTMAP ==> [0000008000 - 000000f000]
Zone PFN ranges:
  DMA      0x00000000 -> 0x00001000
  Normal   0x00001000 -> 0x00038000
  HighMem  0x00038000 -> 0x00880000
Movable zone start PFN for each node
early_node_map[4] active PFN ranges
    0: 0x00000000 -> 0x000000a0
    0: 0x00000100 -> 0x0007fab0
    0: 0x0007fac4 -> 0x0007fac6
    0: 0x00100000 -> 0x00880000
On node 0 totalpages: 8387154
  DMA zone: 3968 pages, LIFO batch:0
  Normal zone: 223520 pages, LIFO batch:31
  HighMem zone: 8090034 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x08] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x10] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x18] enabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x02] enabled)
ACPI: LAPIC (acpi_id[0x05] lapic_id[0x0a] enabled)
ACPI: LAPIC (acpi_id[0x06] lapic_id[0x12] enabled)
ACPI: LAPIC (acpi_id[0x07] lapic_id[0x1a] enabled)
ACPI: LAPIC (acpi_id[0x08] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x09] lapic_id[0x09] enabled)
ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x11] enabled)
ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x19] enabled)
ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x03] enabled)
ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x0b] enabled)
ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x13] enabled)
ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x1b] enabled)
ACPI: LAPIC (acpi_id[0x10] lapic_id[0x1f] disabled)
ACPI: LAPIC (acpi_id[0x11] lapic_id[0x20] disabled)
ACPI: LAPIC (acpi_id[0x12] lapic_id[0x21] disabled)
ACPI: LAPIC (acpi_id[0x13] lapic_id[0x22] disabled)
ACPI: LAPIC (acpi_id[0x14] lapic_id[0x23] disabled)
ACPI: LAPIC (acpi_id[0x15] lapic_id[0x24] disabled)
ACPI: LAPIC (acpi_id[0x16] lapic_id[0x25] disabled)
ACPI: LAPIC (acpi_id[0x17] lapic_id[0x26] disabled)
ACPI: LAPIC (acpi_id[0x18] lapic_id[0x27] disabled)
ACPI: LAPIC (acpi_id[0x19] lapic_id[0x28] disabled)
ACPI: LAPIC (acpi_id[0x1a] lapic_id[0x29] disabled)
ACPI: LAPIC (acpi_id[0x1b] lapic_id[0x2a] disabled)
ACPI: LAPIC (acpi_id[0x1c] lapic_id[0x2b] disabled)
ACPI: LAPIC (acpi_id[0x1d] lapic_id[0x2c] disabled)
ACPI: LAPIC (acpi_id[0x1e] lapic_id[0x2d] disabled)
ACPI: LAPIC (acpi_id[0x1f] lapic_id[0x2e] disabled)
ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
ACPI: IOAPIC (id[0x06] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 6, version 32, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x07] address[0xfec81000] gsi_base[32])
IOAPIC[1]: apic_id 7, version 32, address 0xfec81000, GSI 32-55
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 2 I/O APICs
ACPI: HPET id: 0x8086a201 base: 0xfed00000
SMP: Allowing 16 CPUs, 0 hotplug CPUs
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
mapped IOAPIC to ffff9000 (fec81000)
PM: Registered nosave memory: 00000000000a0000 - 0000000000100000
Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
PERCPU: Allocating 39684 bytes of per cpu data
NR_CPUS: 16, nr_cpu_ids: 16, nr_node_ids 1
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8317522
Kernel command line: BOOT_IMAGE=(hd0,14)/safe/bzc1 root=/dev/sda2 resume=/dev/sda3 reboot=bios maxcpus=8
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
Preemptible RCU implementation.
CPU 0 irqstacks, hard=c0526000 soft=c0516000
PID hash table entries: 4096 (order: 12, 16384 bytes)
Extended CMOS year: 2000
TSC calibrated against PM_TIMER
Detected 1861.912 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 33262724k/35651584k available (2654k kernel code, 285080k reserved, 1241k data, 260k init, 32631496k highmem)
virtual kernel memory layout:
    fixmap  : 0xffee9000 - 0xfffff000   (1112 kB)
    pkmap   : 0xffa00000 - 0xffc00000   (2048 kB)
    vmalloc : 0xf8800000 - 0xff9fe000   ( 113 MB)
    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
      .init : 0xc04d2000 - 0xc0513000   ( 260 kB)
      .data : 0xc0397a33 - 0xc04cde88   (1241 kB)
      .text : 0xc0100000 - 0xc0397a33   (2654 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
CPA: page pool initialized 1 of 1 pages preallocated
SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=16, Nodes=1
hpet clockevent registered
Calibrating delay loop (skipped), value calculated using timer frequency.. 3723.82 BogoMIPS (lpj=7447648)
Mount-cache hash table entries: 512
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
using mwait in idle threads.
Checking 'hlt' instruction... OK.
ACPI: Core revision 20080609
More than 8 CPUs detected - skipping them.
Use CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP.
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
CPU 1 irqstacks, hard=c0527000 soft=c0517000
Booting processor 1/8 ip 6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3723.84 BogoMIPS (lpj=7447688)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 0
CPU1: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
CPU 2 irqstacks, hard=c0528000 soft=c0518000
Booting processor 2/16 ip 6000
Initializing CPU#2
Calibrating delay using timer specific routine.. 3723.85 BogoMIPS (lpj=7447701)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 4
CPU: Processor Core ID: 0
CPU2: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#2]: passed.
CPU 3 irqstacks, hard=c0529000 soft=c0519000
Booting processor 3/24 ip 6000
Initializing CPU#3
Calibrating delay using timer specific routine.. 3723.86 BogoMIPS (lpj=7447726)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 6
CPU: Processor Core ID: 0
CPU3: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#3]: passed.
CPU 4 irqstacks, hard=c052a000 soft=c051a000
Booting processor 4/2 ip 6000
Initializing CPU#4
Calibrating delay using timer specific routine.. 3723.78 BogoMIPS (lpj=7447570)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 2
CPU4: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#4]: passed.
CPU 5 irqstacks, hard=c052b000 soft=c051b000
Booting processor 5/10 ip 6000
Initializing CPU#5
Calibrating delay using timer specific routine.. 3723.83 BogoMIPS (lpj=7447663)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 2
CPU5: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#5]: passed.
CPU 6 irqstacks, hard=c052c000 soft=c051c000
Booting processor 6/18 ip 6000
Initializing CPU#6
Calibrating delay using timer specific routine.. 3723.82 BogoMIPS (lpj=7447658)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 4
CPU: Processor Core ID: 2
CPU6: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#6]: passed.
CPU 7 irqstacks, hard=c052d000 soft=c051d000
Booting processor 7/26 ip 6000
Initializing CPU#7
Calibrating delay using timer specific routine.. 3723.83 BogoMIPS (lpj=7447673)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 6
CPU: Processor Core ID: 2
CPU7: Intel(R) Xeon(R) CPU           L7345  @ 1.86GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#7]: passed.
Brought up 8 CPUs
Total of 8 processors activated (29790.66 BogoMIPS).
net_namespace: 596 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
No dock devices found.
ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
ACPI: bus type pci registered
PCI: Using configuration type 1 for base access
PCI: Dell PowerEdge R900 detected, enabling pci=bfsort.
ACPI: EC: Look up EC in DSDT
ACPI: BIOS _OSI(Linux) query ignored
ACPI: DMI System Vendor: Dell Inc.
ACPI: DMI Product Name: PowerEdge R900
ACPI: DMI Product Version: 
ACPI: DMI Board Name: 0C764H
ACPI: DMI BIOS Vendor: Dell Inc.
ACPI: DMI BIOS Date: 03/23/2008
ACPI: Please send DMI info above to linux-acpi@vger.kernel.org
ACPI: If "acpi_osi=Linux" works better, please notify linux-acpi@vger.kernel.org
ACPI: Interpreter enabled
ACPI: (supports S0 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
pci 0000:00:00.0: PME# disabled
pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
pci 0000:00:01.0: PME# disabled
pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
pci 0000:00:02.0: PME# disabled
pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
pci 0000:00:03.0: PME# disabled
pci 0000:00:04.0: PME# supported from D0 D3hot D3cold
pci 0000:00:04.0: PME# disabled
pci 0000:00:06.0: PME# supported from D0 D3hot D3cold
pci 0000:00:06.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:16:00.0: PME# supported from D0 D3hot D3cold
pci 0000:16:00.0: PME# disabled
pci 0000:16:00.3: PME# supported from D0 D3hot D3cold
pci 0000:16:00.3: PME# disabled
pci 0000:17:00.0: PME# supported from D0 D3hot D3cold
pci 0000:17:00.0: PME# disabled
pci 0000:17:01.0: PME# supported from D0 D3hot D3cold
pci 0000:17:01.0: PME# disabled
pci 0000:19:00.0: supports D1
pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
pci 0000:01:00.0: PME# disabled
pci 0000:02:01.0: PME# supported from D0 D3hot D3cold
pci 0000:02:01.0: PME# disabled
pci 0000:02:02.0: PME# supported from D0 D3hot D3cold
pci 0000:02:02.0: PME# disabled
pci 0000:02:03.0: PME# supported from D0 D3hot D3cold
pci 0000:02:03.0: PME# disabled
pci 0000:02:04.0: PME# supported from D0 D3hot D3cold
pci 0000:02:04.0: PME# disabled
pci 0000:02:05.0: PME# supported from D0 D3hot D3cold
pci 0000:02:05.0: PME# disabled
pci 0000:0a:00.0: PME# supported from D0 D3hot D3cold
pci 0000:0a:00.0: PME# disabled
pci 0000:0b:00.0: PME# supported from D3hot D3cold
pci 0000:0b:00.0: PME# disabled
pci 0000:08:00.0: PME# supported from D0 D3hot D3cold
pci 0000:08:00.0: PME# disabled
pci 0000:09:00.0: PME# supported from D3hot D3cold
pci 0000:09:00.0: PME# disabled
pci 0000:06:00.0: PME# supported from D0 D3hot D3cold
pci 0000:06:00.0: PME# disabled
pci 0000:07:00.0: PME# supported from D3hot D3cold
pci 0000:07:00.0: PME# disabled
pci 0000:04:00.0: PME# supported from D0 D3hot D3cold
pci 0000:04:00.0: PME# disabled
pci 0000:05:00.0: PME# supported from D3hot D3cold
pci 0000:05:00.0: PME# disabled
pci 0000:0c:00.0: PME# supported from D0 D3hot D3cold
pci 0000:0c:00.0: PME# disabled
pci 0000:0d:02.0: PME# supported from D0 D3hot D3cold
pci 0000:0d:02.0: PME# disabled
pci 0000:0d:04.0: PME# supported from D0 D3hot D3cold
pci 0000:0d:04.0: PME# disabled
pci 0000:10:00.0: PME# supported from D0 D3hot D3cold
pci 0000:10:00.0: PME# disabled
pci 0000:11:02.0: PME# supported from D0 D3hot D3cold
pci 0000:11:02.0: PME# disabled
pci 0000:11:04.0: PME# supported from D0 D3hot D3cold
pci 0000:11:04.0: PME# disabled
pci 0000:1b:0c.0: supports D1
pci 0000:1b:0c.0: supports D2
pci 0000:00:1e.0: transparent bridge
bus 00 -> node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2.UPST._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2.UPST.DWN1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2.UPST.DWN2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3.UPST.DWN2.BCOM._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3.UPST.DWN3.BCOM._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3.UPST.DWN4.BCOM._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3.UPST.DWN5.BCOM._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4.UPST.DWNB._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4.UPST.DWNC._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX6.UPST.DWNB._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX6.UPST.DWNC._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.SBEX._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.COMP._PRT]
ACPI: PCI Interrupt Link [LK00] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LK01] (IRQs 3 4 5 6 7 *10 11 12)
ACPI: PCI Interrupt Link [LK02] (IRQs 3 4 5 *6 7 10 11 12)
ACPI: PCI Interrupt Link [LK03] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LK04] (IRQs 3 4 *5 6 7 10 11 12)
ACPI: PCI Interrupt Link [LK05] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LK06] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LK07] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
Switched to high resolution mode on CPU 0
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 2
Switched to high resolution mode on CPU 3
Switched to high resolution mode on CPU 4
Switched to high resolution mode on CPU 5
Switched to high resolution mode on CPU 6
Switched to high resolution mode on CPU 7
system 00:07: ioport range 0x800-0x87f has been reserved
system 00:07: ioport range 0x880-0x8bf has been reserved
system 00:07: ioport range 0x8c0-0x8df has been reserved
system 00:07: ioport range 0x8e0-0x8e3 has been reserved
system 00:07: ioport range 0x8f0-0x8f1 has been reserved
system 00:07: ioport range 0x900-0x900 has been reserved
system 00:07: ioport range 0xc00-0xc7f has been reserved
system 00:07: ioport range 0xca0-0xca7 has been reserved
system 00:07: ioport range 0xca9-0xcab has been reserved
system 00:07: ioport range 0xcad-0xcaf has been reserved
system 00:08: ioport range 0xca8-0xca8 has been reserved
system 00:08: ioport range 0xcac-0xcac has been reserved
system 00:09: iomem range 0xe0000000-0xefffffff could not be reserved
pci 0000:00:01.0: PCI bridge, secondary bus 0000:14
pci 0000:00:01.0:   IO window: disabled
pci 0000:00:01.0:   MEM window: disabled
pci 0000:00:01.0:   PREFETCH window: disabled
pci 0000:17:00.0: PCI bridge, secondary bus 0000:19
pci 0000:17:00.0:   IO window: 0xe000-0xefff
pci 0000:17:00.0:   MEM window: 0xde200000-0xde3fffff
pci 0000:17:00.0:   PREFETCH window: disabled
pci 0000:17:01.0: PCI bridge, secondary bus 0000:18
pci 0000:17:01.0:   IO window: disabled
pci 0000:17:01.0:   MEM window: disabled
pci 0000:17:01.0:   PREFETCH window: disabled
pci 0000:16:00.0: PCI bridge, secondary bus 0000:17
pci 0000:16:00.0:   IO window: 0xe000-0xefff
pci 0000:16:00.0:   MEM window: 0xde200000-0xde3fffff
pci 0000:16:00.0:   PREFETCH window: disabled
pci 0000:16:00.3: PCI bridge, secondary bus 0000:1a
pci 0000:16:00.3:   IO window: disabled
pci 0000:16:00.3:   MEM window: disabled
pci 0000:16:00.3:   PREFETCH window: disabled
pci 0000:00:02.0: PCI bridge, secondary bus 0000:16
pci 0000:00:02.0:   IO window: 0xe000-0xefff
pci 0000:00:02.0:   MEM window: 0xde100000-0xde3fffff
pci 0000:00:02.0:   PREFETCH window: disabled
pci 0000:02:01.0: PCI bridge, secondary bus 0000:03
pci 0000:02:01.0:   IO window: disabled
pci 0000:02:01.0:   MEM window: disabled
pci 0000:02:01.0:   PREFETCH window: disabled
pci 0000:0a:00.0: PCI bridge, secondary bus 0000:0b
pci 0000:0a:00.0:   IO window: disabled
pci 0000:0a:00.0:   MEM window: 0xd6000000-0xd7ffffff
pci 0000:0a:00.0:   PREFETCH window: disabled
pci 0000:02:02.0: PCI bridge, secondary bus 0000:0a
pci 0000:02:02.0:   IO window: disabled
pci 0000:02:02.0:   MEM window: 0xd6000000-0xd7ffffff
pci 0000:02:02.0:   PREFETCH window: disabled
pci 0000:08:00.0: PCI bridge, secondary bus 0000:09
pci 0000:08:00.0:   IO window: disabled
pci 0000:08:00.0:   MEM window: 0xd8000000-0xd9ffffff
pci 0000:08:00.0:   PREFETCH window: disabled
pci 0000:02:03.0: PCI bridge, secondary bus 0000:08
pci 0000:02:03.0:   IO window: disabled
pci 0000:02:03.0:   MEM window: 0xd8000000-0xd9ffffff
pci 0000:02:03.0:   PREFETCH window: disabled
pci 0000:06:00.0: PCI bridge, secondary bus 0000:07
pci 0000:06:00.0:   IO window: disabled
pci 0000:06:00.0:   MEM window: 0xda000000-0xdbffffff
pci 0000:06:00.0:   PREFETCH window: disabled
pci 0000:02:04.0: PCI bridge, secondary bus 0000:06
pci 0000:02:04.0:   IO window: disabled
pci 0000:02:04.0:   MEM window: 0xda000000-0xdbffffff
pci 0000:02:04.0:   PREFETCH window: disabled
pci 0000:04:00.0: PCI bridge, secondary bus 0000:05
pci 0000:04:00.0:   IO window: disabled
pci 0000:04:00.0:   MEM window: 0xdc000000-0xddffffff
pci 0000:04:00.0:   PREFETCH window: disabled
pci 0000:02:05.0: PCI bridge, secondary bus 0000:04
pci 0000:02:05.0:   IO window: disabled
pci 0000:02:05.0:   MEM window: 0xdc000000-0xddffffff
pci 0000:02:05.0:   PREFETCH window: disabled
pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
pci 0000:01:00.0:   IO window: disabled
pci 0000:01:00.0:   MEM window: 0xd6000000-0xddffffff
pci 0000:01:00.0:   PREFETCH window: disabled
pci 0000:00:03.0: PCI bridge, secondary bus 0000:01
pci 0000:00:03.0:   IO window: disabled
pci 0000:00:03.0:   MEM window: 0xd6000000-0xddffffff
pci 0000:00:03.0:   PREFETCH window: disabled
pci 0000:0d:02.0: PCI bridge, secondary bus 0000:0f
pci 0000:0d:02.0:   IO window: disabled
pci 0000:0d:02.0:   MEM window: disabled
pci 0000:0d:02.0:   PREFETCH window: disabled
pci 0000:0d:04.0: PCI bridge, secondary bus 0000:0e
pci 0000:0d:04.0:   IO window: disabled
pci 0000:0d:04.0:   MEM window: disabled
pci 0000:0d:04.0:   PREFETCH window: disabled
pci 0000:0c:00.0: PCI bridge, secondary bus 0000:0d
pci 0000:0c:00.0:   IO window: disabled
pci 0000:0c:00.0:   MEM window: disabled
pci 0000:0c:00.0:   PREFETCH window: disabled
pci 0000:00:04.0: PCI bridge, secondary bus 0000:0c
pci 0000:00:04.0:   IO window: disabled
pci 0000:00:04.0:   MEM window: disabled
pci 0000:00:04.0:   PREFETCH window: disabled
pci 0000:11:02.0: PCI bridge, secondary bus 0000:13
pci 0000:11:02.0:   IO window: disabled
pci 0000:11:02.0:   MEM window: disabled
pci 0000:11:02.0:   PREFETCH window: disabled
pci 0000:11:04.0: PCI bridge, secondary bus 0000:12
pci 0000:11:04.0:   IO window: disabled
pci 0000:11:04.0:   MEM window: disabled
pci 0000:11:04.0:   PREFETCH window: disabled
pci 0000:10:00.0: PCI bridge, secondary bus 0000:11
pci 0000:10:00.0:   IO window: disabled
pci 0000:10:00.0:   MEM window: disabled
pci 0000:10:00.0:   PREFETCH window: disabled
pci 0000:00:06.0: PCI bridge, secondary bus 0000:10
pci 0000:00:06.0:   IO window: disabled
pci 0000:00:06.0:   MEM window: disabled
pci 0000:00:06.0:   PREFETCH window: disabled
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:15
pci 0000:00:1c.0:   IO window: disabled
pci 0000:00:1c.0:   MEM window: disabled
pci 0000:00:1c.0:   PREFETCH window: disabled
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:1b
pci 0000:00:1e.0:   IO window: 0xd000-0xdfff
pci 0000:00:1e.0:   MEM window: 0xde400000-0xde4fffff
pci 0000:00:1e.0:   PREFETCH window: 0x000000c8000000-0x000000cfffffff
pci 0000:00:01.0: PCI INT A -> GSI 36 (level, low) -> IRQ 36
pci 0000:00:01.0: setting latency timer to 64
pci 0000:00:02.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:02.0: setting latency timer to 64
pci 0000:16:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:16:00.0: setting latency timer to 64
pci 0000:17:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:17:00.0: setting latency timer to 64
pci 0000:17:01.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
pci 0000:17:01.0: setting latency timer to 64
pci 0000:16:00.3: setting latency timer to 64
pci 0000:00:03.0: PCI INT A -> GSI 37 (level, low) -> IRQ 37
pci 0000:00:03.0: setting latency timer to 64
pci 0000:01:00.0: setting latency timer to 64
pci 0000:02:01.0: setting latency timer to 64
pci 0000:02:02.0: setting latency timer to 64
pci 0000:0a:00.0: setting latency timer to 64
pci 0000:02:03.0: setting latency timer to 64
pci 0000:08:00.0: setting latency timer to 64
pci 0000:02:04.0: setting latency timer to 64
pci 0000:06:00.0: setting latency timer to 64
pci 0000:02:05.0: setting latency timer to 64
pci 0000:04:00.0: setting latency timer to 64
pci 0000:00:04.0: PCI INT A -> GSI 32 (level, low) -> IRQ 32
pci 0000:00:04.0: setting latency timer to 64
pci 0000:0c:00.0: setting latency timer to 64
pci 0000:0d:02.0: setting latency timer to 64
pci 0000:0d:04.0: setting latency timer to 64
pci 0000:00:06.0: PCI INT A -> GSI 33 (level, low) -> IRQ 33
pci 0000:00:06.0: setting latency timer to 64
pci 0000:10:00.0: setting latency timer to 64
pci 0000:11:02.0: setting latency timer to 64
pci 0000:11:04.0: setting latency timer to 64
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
highmem bounce pool size: 64 pages
HugeTLB registered 2 MB page size, pre-allocated 0 pages
msgmni has been set to 1234
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered (default)
pci 0000:1b:0c.0: Boot video device
pcieport-driver 0000:00:01.0: setting latency timer to 64
pcieport-driver 0000:00:01.0: found MSI capability
pci_express 0000:00:01.0:pcie00: allocate port service
pcieport-driver 0000:00:02.0: setting latency timer to 64
pcieport-driver 0000:00:02.0: found MSI capability
pci_express 0000:00:02.0:pcie00: allocate port service
pcieport-driver 0000:00:03.0: setting latency timer to 64
pcieport-driver 0000:00:03.0: found MSI capability
pci_express 0000:00:03.0:pcie00: allocate port service
pcieport-driver 0000:00:04.0: setting latency timer to 64
pcieport-driver 0000:00:04.0: found MSI capability
pci_express 0000:00:04.0:pcie00: allocate port service
pcieport-driver 0000:00:06.0: setting latency timer to 64
pcieport-driver 0000:00:06.0: found MSI capability
pci_express 0000:00:06.0:pcie00: allocate port service
pcieport-driver 0000:00:1c.0: setting latency timer to 64
pcieport-driver 0000:00:1c.0: found MSI capability
pci_express 0000:00:1c.0:pcie00: allocate port service
pci_express 0000:00:1c.0:pcie02: allocate port service
pcieport-driver 0000:01:00.0: setting latency timer to 64
pcieport-driver 0000:02:01.0: setting latency timer to 64
pcieport-driver 0000:02:01.0: found MSI capability
pcieport-driver 0000:02:02.0: setting latency timer to 64
pcieport-driver 0000:02:02.0: found MSI capability
pcieport-driver 0000:02:03.0: setting latency timer to 64
pcieport-driver 0000:02:03.0: found MSI capability
pcieport-driver 0000:02:04.0: setting latency timer to 64
pcieport-driver 0000:02:04.0: found MSI capability
pcieport-driver 0000:02:05.0: setting latency timer to 64
pcieport-driver 0000:02:05.0: found MSI capability
pcieport-driver 0000:0c:00.0: setting latency timer to 64
pcieport-driver 0000:0d:02.0: setting latency timer to 64
pcieport-driver 0000:0d:02.0: found MSI capability
pcieport-driver 0000:0d:04.0: setting latency timer to 64
pcieport-driver 0000:0d:04.0: found MSI capability
pcieport-driver 0000:10:00.0: setting latency timer to 64
pcieport-driver 0000:11:02.0: setting latency timer to 64
pcieport-driver 0000:11:02.0: found MSI capability
pcieport-driver 0000:11:04.0: setting latency timer to 64
pcieport-driver 0000:11:04.0: found MSI capability
pcieport-driver 0000:16:00.0: setting latency timer to 64
pcieport-driver 0000:17:00.0: setting latency timer to 64
pcieport-driver 0000:17:00.0: found MSI capability
pcieport-driver 0000:17:01.0: setting latency timer to 64
pcieport-driver 0000:17:01.0: found MSI capability
input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
ACPI: Power Button (FF) [PWRF]
processor ACPI0007:00: registered as cooling_device0
processor ACPI0007:01: registered as cooling_device1
processor ACPI0007:02: registered as cooling_device2
processor ACPI0007:03: registered as cooling_device3
processor ACPI0007:04: registered as cooling_device4
processor ACPI0007:05: registered as cooling_device5
processor ACPI0007:06: registered as cooling_device6
processor ACPI0007:07: registered as cooling_device7
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.103
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
pcnet32.c:v1.35 21.Apr.2008 tsbogend@alpha.franken.de
Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.7.9 (July 18, 2008)
bnx2 0000:05:00.0: PCI INT A -> GSI 38 (level, low) -> IRQ 38
eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem dc000000, IRQ 38, node addr 00:1e:c9:d9:84:57
bnx2 0000:07:00.0: PCI INT A -> GSI 37 (level, low) -> IRQ 37
eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem da000000, IRQ 37, node addr 00:1e:c9:d9:84:59
bnx2 0000:09:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
eth2: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem d8000000, IRQ 19, node addr 00:1e:c9:d9:84:5b
bnx2 0000:0b:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
eth3: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem d6000000, IRQ 18, node addr 00:1e:c9:d9:84:5d
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
Uniform Multi-Platform E-IDE driver
ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports
Probing IDE interface ide0...
hda: TSSTcorpDVD-ROM TS-L333A, ATAPI CD/DVD-ROM drive
Probing IDE interface ide1...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
megasas: 00.00.03.20-rc1 Mon. March 10 11:02:31 PDT 2008
megasas: 0x1000:0x0060:0x1028:0x1f0c: bus 25:slot 0:func 0
megaraid_sas 0000:19:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
megaraid_sas 0000:19:00.0: setting latency timer to 64
megasas: FW now in Ready state
scsi0 : LSI SAS based MegaRAID driver
scsi 0:0:0:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:1:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:2:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:3:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:4:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:5:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:6:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:7:0: Direct-Access     SEAGATE  ST973451SS       SM04 PQ: 0 ANSI: 5
scsi 0:0:32:0: Enclosure         DP       BACKPLANE        1.06 PQ: 0 ANSI: 5
scsi 0:2:0:0: Direct-Access     DELL     PERC 6/i         1.11 PQ: 0 ANSI: 5
Driver 'sd' needs updating - please use bus_type methods
sd 0:2:0:0: [sda] 710410240 512-byte hardware sectors (363730 MB)
sd 0:2:0:0: [sda] Write Protect is off
sd 0:2:0:0: [sda] Mode Sense: 1f 00 00 08
sd 0:2:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:2:0:0: [sda] 710410240 512-byte hardware sectors (363730 MB)
sd 0:2:0:0: [sda] Write Protect is off
sd 0:2:0:0: [sda] Mode Sense: 1f 00 00 08
sd 0:2:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 sda13 sda14 sda15 >
sd 0:2:0:0: [sda] Attached SCSI disk
ata_piix 0000:00:1f.2: version 2.12
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
ata_piix 0000:00:1f.2: BAR 0: can't reserve I/O region [0x1f0-0x1f7]
ata_piix 0000:00:1f.2: failed to request/iomap BARs for port 0 (errno=-16)
ata_piix 0000:00:1f.2: BAR 2: can't reserve I/O region [0x170-0x177]
ata_piix 0000:00:1f.2: failed to request/iomap BARs for port 1 (errno=-16)
ata_piix 0000:00:1f.2: no available native port
Fusion MPT base driver 3.04.07
Copyright (c) 1999-2008 LSI Corporation
Fusion MPT SPI Host driver 3.04.07
ehci_hcd 0000:00:1d.7: PCI INT B -> GSI 21 (level, low) -> IRQ 21
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 21, io mem 0xde0ffc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.27-rc3 ehci_hcd
usb usb1: SerialNumber: 0000:00:1d.7
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
USB Universal Host Controller Interface driver v3.0
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 20, io base 0x0000cc80
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb 1-2: new high speed USB device using ehci_hcd and address 2
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.27-rc3 uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.0
uhci_hcd 0000:00:1d.1: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 20, io base 0x0000cca0
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 1-2: configuration #1 chosen from 1 choice
hub 1-2:1.0: USB hub found
hub 1-2:1.0: 2 ports detected
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.27-rc3 uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.1
uhci_hcd 0000:00:1d.2: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 20, io base 0x0000ccc0
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-2: New USB device found, idVendor=413c, idProduct=a001
usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.27-rc3 uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.2
uhci_hcd 0000:00:1d.3: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1d.3: setting latency timer to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 20, io base 0x0000cce0
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 1-7: new high speed USB device using ehci_hcd and address 4
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.27-rc3 uhci_hcd
usb usb5: SerialNumber: 0000:00:1d.3
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
usb 1-7: configuration #1 chosen from 1 choice
hub 1-7:1.0: USB hub found
hub 1-7:1.0: 2 ports detected
input: PC Speaker as /devices/platform/pcspkr/input/input1
coretemp coretemp.0: Using relative temperature scale!
coretemp coretemp.1: Using relative temperature scale!
coretemp coretemp.2: Using relative temperature scale!
coretemp coretemp.3: Using relative temperature scale!
coretemp coretemp.4: Using relative temperature scale!
coretemp coretemp.5: Using relative temperature scale!
coretemp coretemp.6: Using relative temperature scale!
coretemp coretemp.7: Using relative temperature scale!
hdaps: supported laptop not found!
hdaps: driver init failed (ret=-19)!
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
EDAC MC: Ver: 2.1.0 Aug 18 2008
usb 1-7: New USB device found, idVendor=04b4, idProduct=6560
usb 1-7: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 3-1: new low speed USB device using uhci_hcd and address 2
usb 3-1: configuration #1 chosen from 1 choice
usb 3-1: New USB device found, idVendor=0624, idProduct=0294
usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 3-1: Product: Dell 03R874
usb 3-1: Manufacturer: Avocent
usb 1-2.1: new full speed USB device using ehci_hcd and address 5
usb 1-2.1: configuration #1 chosen from 1 choice
usb 1-2.1: New USB device found, idVendor=413c, idProduct=0000
usb 1-2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-2.1: Product: DRAC5
usb 1-2.1: Manufacturer: Dell
usb 1-2.1: SerialNumber: 0000000
usb 1-7.1: new high speed USB device using ehci_hcd and address 6
usb 1-7.1: configuration #1 chosen from 1 choice
hub 1-7.1:1.0: USB hub found
hub 1-7.1:1.0: 2 ports detected
usb 1-7.1: New USB device found, idVendor=04b4, idProduct=6560
usb 1-7.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usbcore: registered new interface driver hiddev
input: Avocent Dell 03R874 as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input2
input: USB HID v1.10 Keyboard [Avocent Dell 03R874] on usb-0000:00:1d.1-1
input: Avocent Dell 03R874 as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.1/input/input3
input: USB HID v1.10 Mouse [Avocent Dell 03R874] on usb-0000:00:1d.1-1
input: Dell DRAC5 as /devices/pci0000:00/0000:00:1d.7/usb1/1-2/1-2.1/1-2.1:1.0/input/input4
input: USB HID v1.10 Keyboard [Dell DRAC5] on usb-0000:00:1d.7-2.1
input: Dell DRAC5 as /devices/pci0000:00/0000:00:1d.7/usb1/1-2/1-2.1/1-2.1:1.1/input/input5
input: USB HID v1.10 Mouse [Dell DRAC5] on usb-0000:00:1d.7-2.1
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.17.
ALSA device list:
  No soundcards found.
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 17
Starting balanced_irq
Using IPI No-Shortcut mode
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 260k freed
Adding 27350652k swap on /dev/sda3.  Priority:-1 extents:1 across:27350652k
bnx2: eth0: using MSI
bnx2: eth1: using MSI
bnx2: eth0 NIC Copper Link is Up, 1000 Mbps full duplex

Re: 2.6.27rc1 cannot boot more than 8CPUs

[Ingo Molnar]

* Jeff Chua <jeff.chua.linux@gmail.com> wrote:

> On Fri, Aug 15, 2008 at 10:07 PM, Ingo Molnar <mingo@elte.hu> wrote:
> 
> > thanks. To make sure it's all sorted out you might want to boot 
> > today's tip/master and check whether it just does the right thing by 
> > default. (it really should)
> 
> Yes, verified and it's working now. The warnings show up.

and the system is up with ~8 cores active [not just 1 or 2], right?

ah, indeed:

> checking TSC synchronization [CPU#0 -> CPU#7]: passed.
> Brought up 8 CPUs
> Total of 8 processors activated (29790.66 BogoMIPS).

great - thanks for testing!

	Ingo