* Problem with SI3124-based controller and SI 4726-based PMP in RAID10 mode
@ 2008-12-10 19:56 daumas
2008-12-10 21:49 ` Andrew Morton
0 siblings, 1 reply; 2+ messages in thread
From: daumas @ 2008-12-10 19:56 UTC (permalink / raw)
To: linux-kernel
I have a sata_sil24 problem involving a 4-port SI3124-based controller
connected to a 3-port eSATA enclosure. Each eSATA port is an SI
4726-based H/W PMP. The PMPs are connected to (13) 1 TB hard drives, as
indicated below.
PCI3124 Port 1
4726 (Configured in RAID10 mode)
4726 Port 1 => 1 TB drive
4726 Port 2 => 1 TB drive
4726 Port 3 => 1 TB drive
4726 Port 4 => 1 TB drive
4726 Port 5 => 1 TB drive
PCI3124 Port 2
4726 (Configured in RAID10 mode)
4726 Port 1 => 1 TB drive
4726 Port 2 => 1 TB drive
4726 Port 3 => 1 TB drive
4726 Port 4 => 1 TB drive
4726 Port 5 => 1 TB drive
PCI3124 Port 3
4726 (Configured in JBOD/Passthru mode)
4726 Port 1 => 1 TB drive
4726 Port 2 => 1 TB drive
4726 Port 3 => 1 TB drive
4726 Port 4 => no connection
4726 Port 5 => no connection
PCI3124 Port 4 =>no connection
I am running openSuse 11.0 with a 2.6.27.7-4.1 kernel
For the 4726 PMP configured in JBOD mode, all is well, and I can see all
3 disks.
However, for the 4726 PMPs configured in RAID10 mode, I can see NONE of
the disks.
As I understand it, the 4726 is a hardware-based PMP which can handle
RAID10 by itself and thereby offload the RAID processing. I would expect
the 3124 controller to see the drives hidden behind the 4726 as a single
unit, but this does not happen. Instead I get the errors listed at end,
and the RAID10 device is not 'seen' at all. (Key error of note is "both
IDENTIFYs aborted, assuming NODEV")
JBOD is fine for host-only based RAID functionality, but I want the
higher performance the 4726 offers for RAID10.
Is is not possible to off-load the RAID10 function to the 4726 under linux?
Any help, workarounds (beyond strict JBOD mode) are appreciated.
Thanks!
Dec 10 11:02:23 buildhost36 sudo: e-build : TTY=pts/1 ;
PWD=/home/e-build ; USER=root ; COMMAND=/sbin/modprobe sata_sil24
Dec 10 11:02:23 buildhost36 kernel: sata_sil24 0000:03:03.0: version 1.1
Dec 10 11:02:23 buildhost36 kernel: vendor=8086 device=0329
Dec 10 11:02:23 buildhost36 kernel: vendor=8086 device=3595
Dec 10 11:02:23 buildhost36 kernel: sata_sil24 0000:03:03.0: PCI INT A
-> GSI 72 (level, low) -> IRQ 64
Dec 10 11:02:23 buildhost36 kernel: sata_sil24 0000:03:03.0: Applying
completion IRQ loss on PCI-X errata fix
Dec 10 11:02:23 buildhost36 kernel: scsi8 : sata_sil24
Dec 10 11:02:23 buildhost36 kernel: scsi9 : sata_sil24
Dec 10 11:02:23 buildhost36 kernel: scsi10 : sata_sil24
Dec 10 11:02:23 buildhost36 kernel: scsi11 : sata_sil24
Dec 10 11:02:23 buildhost36 kernel: ata7: SATA max UDMA/100 host
m128@0xdefffc00 port 0xdeff0000 irq 64
Dec 10 11:02:23 buildhost36 kernel: ata8: SATA max UDMA/100 host
m128@0xdefffc00 port 0xdeff2000 irq 64
Dec 10 11:02:23 buildhost36 kernel: ata9: SATA max UDMA/100 host
m128@0xdefffc00 port 0xdeff4000 irq 64
Dec 10 11:02:23 buildhost36 kernel: ata10: SATA max UDMA/100 host
m128@0xdefffc00 port 0xdeff6000 irq 64
Dec 10 11:02:25 buildhost36 kernel: ata7: SATA link up 3.0 Gbps (SStatus
123 SControl 0)
Dec 10 11:02:25 buildhost36 kernel: ata7.15: Port Multiplier 1.1,
0x1095:0x4726 r31, 3 ports, feat 0x1/0x9
Dec 10 11:02:25 buildhost36 kernel: ata7.00: hard resetting link
Dec 10 11:02:25 buildhost36 kernel: ata7.00: SATA link down (SStatus 4
SControl 0)
Dec 10 11:02:25 buildhost36 kernel: ata7.01: hard resetting link
Dec 10 11:02:25 buildhost36 kernel: ata7.01: SATA link up 3.0 Gbps
(SStatus 123 SControl 0)
Dec 10 11:02:25 buildhost36 kernel: ata7.02: hard resetting link
Dec 10 11:02:26 buildhost36 kernel: ata7.02: SATA link up 1.5 Gbps
(SStatus 113 SControl 320)
Dec 10 11:02:26 buildhost36 kernel: ata7.01: unsupported device, disabling
Dec 10 11:02:26 buildhost36 kernel: ata7.01: disabled
Dec 10 11:02:26 buildhost36 kernel: ata7.02: both IDENTIFYs aborted,
assuming NODEV
Dec 10 11:02:26 buildhost36 kernel: ata7: EH complete
Dec 10 11:02:28 buildhost36 kernel: ata8: SATA link up 3.0 Gbps (SStatus
123 SControl 0)
Dec 10 11:02:28 buildhost36 kernel: ata8.15: Port Multiplier 1.1,
0x1095:0x4726 r31, 3 ports, feat 0x1/0x9
Dec 10 11:02:28 buildhost36 kernel: ata8.00: hard resetting link
Dec 10 11:02:28 buildhost36 kernel: ata8.00: SATA link down (SStatus 4
SControl 0)
Dec 10 11:02:28 buildhost36 kernel: ata8.01: hard resetting link
Dec 10 11:02:29 buildhost36 kernel: ata8.01: SATA link up 3.0 Gbps
(SStatus 123 SControl 0)
Dec 10 11:02:29 buildhost36 kernel: ata8.02: hard resetting link
Dec 10 11:02:29 buildhost36 kernel: ata8.02: SATA link up 1.5 Gbps
(SStatus 113 SControl 320)
Dec 10 11:02:29 buildhost36 kernel: ata8.01: unsupported device, disabling
Dec 10 11:02:29 buildhost36 kernel: ata8.01: disabled
Dec 10 11:02:29 buildhost36 kernel: ata8.02: both IDENTIFYs aborted,
assuming NODEV
Dec 10 11:02:29 buildhost36 kernel: ata8: EH complete
Dec 10 11:02:31 buildhost36 kernel: ata9: SATA link up 3.0 Gbps (SStatus
123 SControl 0)
Dec 10 11:02:31 buildhost36 kernel: ata9.15: Port Multiplier 1.1,
0x1095:0x4726 r31, 7 ports, feat 0x1/0x9
Dec 10 11:02:31 buildhost36 kernel: ata9.00: hard resetting link
Dec 10 11:02:32 buildhost36 kernel: ata9.00: SATA link up 1.5 Gbps
(SStatus 113 SControl 320)
Dec 10 11:02:32 buildhost36 kernel: ata9.01: hard resetting link
Dec 10 11:02:32 buildhost36 kernel: ata9.01: SATA link up 1.5 Gbps
(SStatus 113 SControl 300)
Dec 10 11:02:32 buildhost36 kernel: ata9.02: hard resetting link
Dec 10 11:02:32 buildhost36 kernel: ata9.02: SATA link up 1.5 Gbps
(SStatus 113 SControl 300)
Dec 10 11:02:32 buildhost36 kernel: ata9.03: hard resetting link
Dec 10 11:02:33 buildhost36 kernel: ata9.03: SATA link down (SStatus 0
SControl 320)
Dec 10 11:02:33 buildhost36 kernel: ata9.04: hard resetting link
Dec 10 11:02:33 buildhost36 kernel: ata9.04: SATA link down (SStatus 0
SControl 320)
Dec 10 11:02:33 buildhost36 kernel: ata9.05: hard resetting link
Dec 10 11:02:33 buildhost36 kernel: ata9.05: SATA link up 3.0 Gbps
(SStatus 123 SControl 0)
Dec 10 11:02:33 buildhost36 kernel: ata9.06: hard resetting link
Dec 10 11:02:34 buildhost36 kernel: ata9.06: SATA link up 1.5 Gbps
(SStatus 113 SControl 320)
Dec 10 11:02:34 buildhost36 kernel: ata9.00: ATA-8: ST31000340AS, SD15,
max UDMA/133
Dec 10 11:02:34 buildhost36 kernel: ata9.00: 1953525168 sectors, multi
0: LBA48 NCQ (depth 31/32)
Dec 10 11:02:34 buildhost36 kernel: ata9.00: configured for UDMA/100
Dec 10 11:02:34 buildhost36 kernel: ata9.01: ATA-8: ST31000340AS, SD15,
max UDMA/133
Dec 10 11:02:34 buildhost36 kernel: ata9.01: 1953525168 sectors, multi
0: LBA48 NCQ (depth 31/32)
Dec 10 11:02:34 buildhost36 kernel: ata9.01: configured for UDMA/100
Dec 10 11:02:34 buildhost36 kernel: ata9.02: ATA-8: ST31000340AS, SD15,
max UDMA/133
Dec 10 11:02:34 buildhost36 kernel: ata9.02: 1953525168 sectors, multi
0: LBA48 NCQ (depth 31/32)
Dec 10 11:02:34 buildhost36 kernel: ata9.02: configured for UDMA/100
Dec 10 11:02:34 buildhost36 kernel: ata9.05: unsupported device, disabling
Dec 10 11:02:34 buildhost36 kernel: ata9.05: disabled
Dec 10 11:02:34 buildhost36 kernel: ata9: EH complete
Dec 10 11:02:36 buildhost36 kernel: ata10: SATA link down (SStatus 0
SControl 0)
Dec 10 11:02:36 buildhost36 kernel: scsi 10:0:0:0: Direct-Access ATA
ST31000340AS SD15 PQ: 0 ANSI: 5
Dec 10 11:02:36 buildhost36 kernel: sd 10:0:0:0: [sdb] 1953525168
512-byte hardware sectors: (1000GB/931GiB)
Dec 10 11:02:36 buildhost36 kernel: sd 10:0:0:0: [sdb] Write Protect is off
Dec 10 11:02:36 buildhost36 kernel: sd 10:0:0:0: [sdb] Mode Sense: 00 3a
00 00
Dec 10 11:02:36 buildhost36 kernel: sd 10:0:0:0: [sdb] Write cache:
enabled, read cache: enabled, doesn't support DPO or FUA
Dec 10 11:02:36 buildhost36 kernel: sd 10:0:0:0: [sdb] 1953525168
512-byte hardware sectors: (1000GB/931GiB)
Dec 10 11:02:36 buildhost36 kernel: sd 10:0:0:0: [sdb] Write Protect is off
Dec 10 11:02:36 buildhost36 kernel: sd 10:0:0:0: [sdb] Mode Sense: 00 3a
00 00
Dec 10 11:02:36 buildhost36 kernel: sd 10:0:0:0: [sdb] Write cache:
enabled, read cache: enabled, doesn't support DPO or FUA
Dec 10 11:02:36 buildhost36 kernel: sdb:
Dec 10 11:02:36 buildhost36 kernel: sd 10:0:0:0: [sdb] Attached SCSI disk
Dec 10 11:02:36 buildhost36 kernel: sd 10:0:0:0: Attached scsi generic
sg2 type 0
Dec 10 11:02:36 buildhost36 kernel: scsi 10:1:0:0: Direct-Access ATA
ST31000340AS SD15 PQ: 0 ANSI: 5
Dec 10 11:02:36 buildhost36 kernel: sd 10:1:0:0: [sdc] 1953525168
512-byte hardware sectors: (1000GB/931GiB)
Dec 10 11:02:36 buildhost36 kernel: sd 10:1:0:0: [sdc] Write Protect is off
Dec 10 11:02:36 buildhost36 kernel: sd 10:1:0:0: [sdc] Mode Sense: 00 3a
00 00
Dec 10 11:02:36 buildhost36 kernel: sd 10:1:0:0: [sdc] Write cache:
enabled, read cache: enabled, doesn't support DPO or FUA
Dec 10 11:02:36 buildhost36 kernel: sd 10:1:0:0: [sdc] 1953525168
512-byte hardware sectors: (1000GB/931GiB)
Dec 10 11:02:36 buildhost36 kernel: sd 10:1:0:0: [sdc] Write Protect is off
Dec 10 11:02:36 buildhost36 kernel: sd 10:1:0:0: [sdc] Mode Sense: 00 3a
00 00
Dec 10 11:02:36 buildhost36 kernel: sd 10:1:0:0: [sdc] Write cache:
enabled, read cache: enabled, doesn't support DPO or FUA
Dec 10 11:02:36 buildhost36 kernel: sdc:
Dec 10 11:02:36 buildhost36 kernel: sd 10:1:0:0: [sdc] Attached SCSI disk
Dec 10 11:02:36 buildhost36 kernel: sd 10:1:0:0: Attached scsi generic
sg3 type 0
Dec 10 11:02:36 buildhost36 kernel: scsi 10:2:0:0: Direct-Access ATA
ST31000340AS SD15 PQ: 0 ANSI: 5
Dec 10 11:02:36 buildhost36 kernel: sd 10:2:0:0: [sdd] 1953525168
512-byte hardware sectors: (1000GB/931GiB)
Dec 10 11:02:36 buildhost36 kernel: sd 10:2:0:0: [sdd] Write Protect is off
Dec 10 11:02:36 buildhost36 kernel: sd 10:2:0:0: [sdd] Mode Sense: 00 3a
00 00
Dec 10 11:02:36 buildhost36 kernel: sd 10:2:0:0: [sdd] Write cache:
enabled, read cache: enabled, doesn't support DPO or FUA
Dec 10 11:02:36 buildhost36 kernel: sd 10:2:0:0: [sdd] 1953525168
512-byte hardware sectors: (1000GB/931GiB)
Dec 10 11:02:36 buildhost36 kernel: sd 10:2:0:0: [sdd] Write Protect is off
Dec 10 11:02:36 buildhost36 kernel: sd 10:2:0:0: [sdd] Mode Sense: 00 3a
00 00
Dec 10 11:02:36 buildhost36 kernel: sd 10:2:0:0: [sdd] Write cache:
enabled, read cache: enabled, doesn't support DPO or FUA
Dec 10 11:02:36 buildhost36 kernel: sdd: sdd1
Dec 10 11:02:36 buildhost36 kernel: sd 10:2:0:0: [sdd] Attached SCSI disk
Dec 10 11:02:36 buildhost36 kernel: sd 10:2:0:0: Attached scsi generic
sg4 type 0
Dec 10 11:02:55 buildhost36 sshd[6534]: Accepted
keyboard-interactive/pam for e-build from 9.65.98.119 port 34222 ssh2
Dec 10 11:03:57 buildhost36 sshd[6566]: Accepted
keyboard-interactive/pam for root from 9.65.98.119 port 44494 ssh2
Henri Daumas
Global TIM Competency - Integrated Operations
Configuration Management/Build
^ permalink raw reply [flat|nested] 2+ messages in thread
* Re: Problem with SI3124-based controller and SI 4726-based PMP in RAID10 mode
2008-12-10 19:56 Problem with SI3124-based controller and SI 4726-based PMP in RAID10 mode daumas
@ 2008-12-10 21:49 ` Andrew Morton
0 siblings, 0 replies; 2+ messages in thread
From: Andrew Morton @ 2008-12-10 21:49 UTC (permalink / raw)
To: daumas; +Cc: linux-kernel, linux-ide
(cc linux-ide)
On Wed, 10 Dec 2008 13:56:52 -0600
daumas <daumas77@gmail.com> wrote:
>
> I have a sata_sil24 problem involving a 4-port SI3124-based controller
> connected to a 3-port eSATA enclosure. Each eSATA port is an SI
> 4726-based H/W PMP. The PMPs are connected to (13) 1 TB hard drives, as
> indicated below.
>
> PCI3124 Port 1
> 4726 (Configured in RAID10 mode)
> 4726 Port 1 => 1 TB drive
> 4726 Port 2 => 1 TB drive
> 4726 Port 3 => 1 TB drive
> 4726 Port 4 => 1 TB drive
> 4726 Port 5 => 1 TB drive
> PCI3124 Port 2
> 4726 (Configured in RAID10 mode)
> 4726 Port 1 => 1 TB drive
> 4726 Port 2 => 1 TB drive
> 4726 Port 3 => 1 TB drive
> 4726 Port 4 => 1 TB drive
> 4726 Port 5 => 1 TB drive
> PCI3124 Port 3
> 4726 (Configured in JBOD/Passthru mode)
> 4726 Port 1 => 1 TB drive
> 4726 Port 2 => 1 TB drive
> 4726 Port 3 => 1 TB drive
> 4726 Port 4 => no connection
> 4726 Port 5 => no connection
> PCI3124 Port 4 =>no connection
>
> I am running openSuse 11.0 with a 2.6.27.7-4.1 kernel
>
> For the 4726 PMP configured in JBOD mode, all is well, and I can see all
> 3 disks.
>
> However, for the 4726 PMPs configured in RAID10 mode, I can see NONE of
> the disks.
>
> As I understand it, the 4726 is a hardware-based PMP which can handle
> RAID10 by itself and thereby offload the RAID processing. I would expect
> the 3124 controller to see the drives hidden behind the 4726 as a single
> unit, but this does not happen. Instead I get the errors listed at end,
> and the RAID10 device is not 'seen' at all. (Key error of note is "both
> IDENTIFYs aborted, assuming NODEV")
>
> JBOD is fine for host-only based RAID functionality, but I want the
> higher performance the 4726 offers for RAID10.
> Is is not possible to off-load the RAID10 function to the 4726 under linux?
>
> Any help, workarounds (beyond strict JBOD mode) are appreciated.
>
> Thanks!
>
> Dec 10 11:02:23 buildhost36 sudo: e-build : TTY=pts/1 ;
> PWD=/home/e-build ; USER=root ; COMMAND=/sbin/modprobe sata_sil24
> Dec 10 11:02:23 buildhost36 kernel: sata_sil24 0000:03:03.0: version 1.1
> Dec 10 11:02:23 buildhost36 kernel: vendor=8086 device=0329
> Dec 10 11:02:23 buildhost36 kernel: vendor=8086 device=3595
> Dec 10 11:02:23 buildhost36 kernel: sata_sil24 0000:03:03.0: PCI INT A
> -> GSI 72 (level, low) -> IRQ 64
> Dec 10 11:02:23 buildhost36 kernel: sata_sil24 0000:03:03.0: Applying
> completion IRQ loss on PCI-X errata fix
> Dec 10 11:02:23 buildhost36 kernel: scsi8 : sata_sil24
> Dec 10 11:02:23 buildhost36 kernel: scsi9 : sata_sil24
> Dec 10 11:02:23 buildhost36 kernel: scsi10 : sata_sil24
> Dec 10 11:02:23 buildhost36 kernel: scsi11 : sata_sil24
> Dec 10 11:02:23 buildhost36 kernel: ata7: SATA max UDMA/100 host
> m128@0xdefffc00 port 0xdeff0000 irq 64
> Dec 10 11:02:23 buildhost36 kernel: ata8: SATA max UDMA/100 host
> m128@0xdefffc00 port 0xdeff2000 irq 64
> Dec 10 11:02:23 buildhost36 kernel: ata9: SATA max UDMA/100 host
> m128@0xdefffc00 port 0xdeff4000 irq 64
> Dec 10 11:02:23 buildhost36 kernel: ata10: SATA max UDMA/100 host
> m128@0xdefffc00 port 0xdeff6000 irq 64
> Dec 10 11:02:25 buildhost36 kernel: ata7: SATA link up 3.0 Gbps (SStatus
> 123 SControl 0)
> Dec 10 11:02:25 buildhost36 kernel: ata7.15: Port Multiplier 1.1,
> 0x1095:0x4726 r31, 3 ports, feat 0x1/0x9
> Dec 10 11:02:25 buildhost36 kernel: ata7.00: hard resetting link
> Dec 10 11:02:25 buildhost36 kernel: ata7.00: SATA link down (SStatus 4
> SControl 0)
> Dec 10 11:02:25 buildhost36 kernel: ata7.01: hard resetting link
> Dec 10 11:02:25 buildhost36 kernel: ata7.01: SATA link up 3.0 Gbps
> (SStatus 123 SControl 0)
> Dec 10 11:02:25 buildhost36 kernel: ata7.02: hard resetting link
> Dec 10 11:02:26 buildhost36 kernel: ata7.02: SATA link up 1.5 Gbps
> (SStatus 113 SControl 320)
> Dec 10 11:02:26 buildhost36 kernel: ata7.01: unsupported device, disabling
> Dec 10 11:02:26 buildhost36 kernel: ata7.01: disabled
> Dec 10 11:02:26 buildhost36 kernel: ata7.02: both IDENTIFYs aborted,
> assuming NODEV
> Dec 10 11:02:26 buildhost36 kernel: ata7: EH complete
> Dec 10 11:02:28 buildhost36 kernel: ata8: SATA link up 3.0 Gbps (SStatus
> 123 SControl 0)
> Dec 10 11:02:28 buildhost36 kernel: ata8.15: Port Multiplier 1.1,
> 0x1095:0x4726 r31, 3 ports, feat 0x1/0x9
> Dec 10 11:02:28 buildhost36 kernel: ata8.00: hard resetting link
> Dec 10 11:02:28 buildhost36 kernel: ata8.00: SATA link down (SStatus 4
> SControl 0)
> Dec 10 11:02:28 buildhost36 kernel: ata8.01: hard resetting link
> Dec 10 11:02:29 buildhost36 kernel: ata8.01: SATA link up 3.0 Gbps
> (SStatus 123 SControl 0)
> Dec 10 11:02:29 buildhost36 kernel: ata8.02: hard resetting link
> Dec 10 11:02:29 buildhost36 kernel: ata8.02: SATA link up 1.5 Gbps
> (SStatus 113 SControl 320)
> Dec 10 11:02:29 buildhost36 kernel: ata8.01: unsupported device, disabling
> Dec 10 11:02:29 buildhost36 kernel: ata8.01: disabled
> Dec 10 11:02:29 buildhost36 kernel: ata8.02: both IDENTIFYs aborted,
> assuming NODEV
> Dec 10 11:02:29 buildhost36 kernel: ata8: EH complete
> Dec 10 11:02:31 buildhost36 kernel: ata9: SATA link up 3.0 Gbps (SStatus
> 123 SControl 0)
> Dec 10 11:02:31 buildhost36 kernel: ata9.15: Port Multiplier 1.1,
> 0x1095:0x4726 r31, 7 ports, feat 0x1/0x9
> Dec 10 11:02:31 buildhost36 kernel: ata9.00: hard resetting link
> Dec 10 11:02:32 buildhost36 kernel: ata9.00: SATA link up 1.5 Gbps
> (SStatus 113 SControl 320)
> Dec 10 11:02:32 buildhost36 kernel: ata9.01: hard resetting link
> Dec 10 11:02:32 buildhost36 kernel: ata9.01: SATA link up 1.5 Gbps
> (SStatus 113 SControl 300)
> Dec 10 11:02:32 buildhost36 kernel: ata9.02: hard resetting link
> Dec 10 11:02:32 buildhost36 kernel: ata9.02: SATA link up 1.5 Gbps
> (SStatus 113 SControl 300)
> Dec 10 11:02:32 buildhost36 kernel: ata9.03: hard resetting link
> Dec 10 11:02:33 buildhost36 kernel: ata9.03: SATA link down (SStatus 0
> SControl 320)
> Dec 10 11:02:33 buildhost36 kernel: ata9.04: hard resetting link
> Dec 10 11:02:33 buildhost36 kernel: ata9.04: SATA link down (SStatus 0
> SControl 320)
> Dec 10 11:02:33 buildhost36 kernel: ata9.05: hard resetting link
> Dec 10 11:02:33 buildhost36 kernel: ata9.05: SATA link up 3.0 Gbps
> (SStatus 123 SControl 0)
> Dec 10 11:02:33 buildhost36 kernel: ata9.06: hard resetting link
> Dec 10 11:02:34 buildhost36 kernel: ata9.06: SATA link up 1.5 Gbps
> (SStatus 113 SControl 320)
> Dec 10 11:02:34 buildhost36 kernel: ata9.00: ATA-8: ST31000340AS, SD15,
> max UDMA/133
> Dec 10 11:02:34 buildhost36 kernel: ata9.00: 1953525168 sectors, multi
> 0: LBA48 NCQ (depth 31/32)
> Dec 10 11:02:34 buildhost36 kernel: ata9.00: configured for UDMA/100
> Dec 10 11:02:34 buildhost36 kernel: ata9.01: ATA-8: ST31000340AS, SD15,
> max UDMA/133
> Dec 10 11:02:34 buildhost36 kernel: ata9.01: 1953525168 sectors, multi
> 0: LBA48 NCQ (depth 31/32)
> Dec 10 11:02:34 buildhost36 kernel: ata9.01: configured for UDMA/100
> Dec 10 11:02:34 buildhost36 kernel: ata9.02: ATA-8: ST31000340AS, SD15,
> max UDMA/133
> Dec 10 11:02:34 buildhost36 kernel: ata9.02: 1953525168 sectors, multi
> 0: LBA48 NCQ (depth 31/32)
> Dec 10 11:02:34 buildhost36 kernel: ata9.02: configured for UDMA/100
> Dec 10 11:02:34 buildhost36 kernel: ata9.05: unsupported device, disabling
> Dec 10 11:02:34 buildhost36 kernel: ata9.05: disabled
> Dec 10 11:02:34 buildhost36 kernel: ata9: EH complete
> Dec 10 11:02:36 buildhost36 kernel: ata10: SATA link down (SStatus 0
> SControl 0)
> Dec 10 11:02:36 buildhost36 kernel: scsi 10:0:0:0: Direct-Access ATA
> ST31000340AS SD15 PQ: 0 ANSI: 5
> Dec 10 11:02:36 buildhost36 kernel: sd 10:0:0:0: [sdb] 1953525168
> 512-byte hardware sectors: (1000GB/931GiB)
> Dec 10 11:02:36 buildhost36 kernel: sd 10:0:0:0: [sdb] Write Protect is off
> Dec 10 11:02:36 buildhost36 kernel: sd 10:0:0:0: [sdb] Mode Sense: 00 3a
> 00 00
> Dec 10 11:02:36 buildhost36 kernel: sd 10:0:0:0: [sdb] Write cache:
> enabled, read cache: enabled, doesn't support DPO or FUA
> Dec 10 11:02:36 buildhost36 kernel: sd 10:0:0:0: [sdb] 1953525168
> 512-byte hardware sectors: (1000GB/931GiB)
> Dec 10 11:02:36 buildhost36 kernel: sd 10:0:0:0: [sdb] Write Protect is off
> Dec 10 11:02:36 buildhost36 kernel: sd 10:0:0:0: [sdb] Mode Sense: 00 3a
> 00 00
> Dec 10 11:02:36 buildhost36 kernel: sd 10:0:0:0: [sdb] Write cache:
> enabled, read cache: enabled, doesn't support DPO or FUA
> Dec 10 11:02:36 buildhost36 kernel: sdb:
> Dec 10 11:02:36 buildhost36 kernel: sd 10:0:0:0: [sdb] Attached SCSI disk
> Dec 10 11:02:36 buildhost36 kernel: sd 10:0:0:0: Attached scsi generic
> sg2 type 0
> Dec 10 11:02:36 buildhost36 kernel: scsi 10:1:0:0: Direct-Access ATA
> ST31000340AS SD15 PQ: 0 ANSI: 5
> Dec 10 11:02:36 buildhost36 kernel: sd 10:1:0:0: [sdc] 1953525168
> 512-byte hardware sectors: (1000GB/931GiB)
> Dec 10 11:02:36 buildhost36 kernel: sd 10:1:0:0: [sdc] Write Protect is off
> Dec 10 11:02:36 buildhost36 kernel: sd 10:1:0:0: [sdc] Mode Sense: 00 3a
> 00 00
> Dec 10 11:02:36 buildhost36 kernel: sd 10:1:0:0: [sdc] Write cache:
> enabled, read cache: enabled, doesn't support DPO or FUA
> Dec 10 11:02:36 buildhost36 kernel: sd 10:1:0:0: [sdc] 1953525168
> 512-byte hardware sectors: (1000GB/931GiB)
> Dec 10 11:02:36 buildhost36 kernel: sd 10:1:0:0: [sdc] Write Protect is off
> Dec 10 11:02:36 buildhost36 kernel: sd 10:1:0:0: [sdc] Mode Sense: 00 3a
> 00 00
> Dec 10 11:02:36 buildhost36 kernel: sd 10:1:0:0: [sdc] Write cache:
> enabled, read cache: enabled, doesn't support DPO or FUA
> Dec 10 11:02:36 buildhost36 kernel: sdc:
> Dec 10 11:02:36 buildhost36 kernel: sd 10:1:0:0: [sdc] Attached SCSI disk
> Dec 10 11:02:36 buildhost36 kernel: sd 10:1:0:0: Attached scsi generic
> sg3 type 0
> Dec 10 11:02:36 buildhost36 kernel: scsi 10:2:0:0: Direct-Access ATA
> ST31000340AS SD15 PQ: 0 ANSI: 5
> Dec 10 11:02:36 buildhost36 kernel: sd 10:2:0:0: [sdd] 1953525168
> 512-byte hardware sectors: (1000GB/931GiB)
> Dec 10 11:02:36 buildhost36 kernel: sd 10:2:0:0: [sdd] Write Protect is off
> Dec 10 11:02:36 buildhost36 kernel: sd 10:2:0:0: [sdd] Mode Sense: 00 3a
> 00 00
> Dec 10 11:02:36 buildhost36 kernel: sd 10:2:0:0: [sdd] Write cache:
> enabled, read cache: enabled, doesn't support DPO or FUA
> Dec 10 11:02:36 buildhost36 kernel: sd 10:2:0:0: [sdd] 1953525168
> 512-byte hardware sectors: (1000GB/931GiB)
> Dec 10 11:02:36 buildhost36 kernel: sd 10:2:0:0: [sdd] Write Protect is off
> Dec 10 11:02:36 buildhost36 kernel: sd 10:2:0:0: [sdd] Mode Sense: 00 3a
> 00 00
> Dec 10 11:02:36 buildhost36 kernel: sd 10:2:0:0: [sdd] Write cache:
> enabled, read cache: enabled, doesn't support DPO or FUA
> Dec 10 11:02:36 buildhost36 kernel: sdd: sdd1
> Dec 10 11:02:36 buildhost36 kernel: sd 10:2:0:0: [sdd] Attached SCSI disk
> Dec 10 11:02:36 buildhost36 kernel: sd 10:2:0:0: Attached scsi generic
> sg4 type 0
> Dec 10 11:02:55 buildhost36 sshd[6534]: Accepted
> keyboard-interactive/pam for e-build from 9.65.98.119 port 34222 ssh2
> Dec 10 11:03:57 buildhost36 sshd[6566]: Accepted
> keyboard-interactive/pam for root from 9.65.98.119 port 44494 ssh2
>
> Henri Daumas
> Global TIM Competency - Integrated Operations
> Configuration Management/Build
>
>
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2008-12-10 21:49 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-12-10 19:56 Problem with SI3124-based controller and SI 4726-based PMP in RAID10 mode daumas
2008-12-10 21:49 ` Andrew Morton
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox