* Unable to write dvd+r on 3 systems
@ 2009-02-14 18:54 Richard Jonsson
2009-02-14 21:53 ` Robert Hancock
0 siblings, 1 reply; 8+ messages in thread
From: Richard Jonsson @ 2009-02-14 18:54 UTC (permalink / raw)
To: linux-kernel
[-- Attachment #1: Type: text/plain, Size: 3061 bytes --]
It seems I am the last person on earth burning dvd's. I have tried on three different systems, using a mix of growisofs, xfburn, brasero and k3b. They all give the same result for their respective system.
On system 1 it takes forever to complete the process. The system is completely useless while burning. IO wait is 50% and hardIRQ is 10-20%. If audio is playing at the same time it stutters in a way that it sounds as it's playing slow. Mouse cursor jerks and it takes eons to even open a new terminal.
On system 2 growisofs will try for half a minute and then fail with a message in dmesg. The disc isn't even touched. Tried homebuilt kernel.org kernels from 2.6.25 to current git with no difference. See attachment "growisofs_system2.txt". I have been able to burn exactly 1 disc in total, which magically started recording immediately.
System 3 burns at decent speed and always reports success, but about half the time only part of the disc is actually burned. It is visible to the eye, and it will not work. Tried at 4x too.
I tried to compile older kernels, 2.6.24 wouldn't boot, and older kernels would not compile on these systems.
System 1 System 2 System 3
System/mainb. HP DV2140eu Advent (noname) Abit NF7-S
Processor Turion TL52-X2 Celeron M420 Athlon 2400+
RAM 2GB 512MB 1GB
DVD-burner HL-DT-ST DVDRAM Slimtype DVDRW Plextor 8x
GMA-4082N hq04 SOSW-833S vs04
OS Ubuntu 8.10 U 8.10 server U 8.10 server
64bit 32bit 32bit
software all above growisofs growisofs, xfburn
I have at this time only tried one make of media (TDK 16x dvd+r):
dvd+rw-mediainfo /dev/dvd
INQUIRY: [HL-DT-ST][DVDRAM GMA-4082N][HQ04]
GET [CURRENT] CONFIGURATION:
Mounted Media: 1Bh, DVD+R
Current Write Speed: 8.0x1385=11080KB/s
Write Speed #0: 8.0x1385=11080KB/s
Write Speed #1: 4.0x1385=5540KB/s
GET [CURRENT] PERFORMANCE:
Write Performance: 3.3x1385=4584KB/s@0 -> 8.0x1385=11092KB/s@2299967
Speed Descriptor#0: 02/2295103 R@3.3x1385=4584KB/s W@8.0x1385=11080KB/s
Speed Descriptor#1: 02/2295103 R@3.3x1385=4584KB/s W@4.0x1385=5540KB/s
READ DVD STRUCTURE[#0h]:
Media Book Type: 00h, DVD-ROM book [revision 0]
Media ID: TDK/003
Legacy lead-out at: 2295104*2KB=4700372992
READ DISC INFORMATION:
Disc status: blank
Number of Sessions: 1
State of Last Session: empty
"Next" Track: 1
Number of Tracks: 1
READ TRACK INFORMATION[#1]:
Track State: blank
Track Start Address: 0*2KB
Next Writable Address: 0*2KB
Free Blocks: 2295104*2KB
Track Size: 2295104*2KB
READ CAPACITY: 0*2048=0
Please cc me as I'm not subscribed, and thanks in advance / Richard
_________________________________________________________________
Kolla mailen när du är på språng - skaffa Hotmail i mobilen!
http://windowslivemobile.msn.com/BrowserServiceHotmail.aspx?lang=SE-SE
[-- Attachment #2: growisofs_system2.txt --]
[-- Type: text/plain, Size: 3294 bytes --]
richie@rox:~$ growisofs -dvd-compat -Z /dev/dvd=image.iso
Executing 'builtin_dd if=image.iso of=/dev/dvd obs=32k seek=0'
/dev/dvd: "Current Write Speed" is 3.3x1352KBps.
0/4698466304 ( 0.0%) @0x, remaining ??:?? RBU 100.0% UBU 0.0%
0/4698466304 ( 0.0%) @0x, remaining ??:?? RBU 100.0% UBU 0.0%
0/4698466304 ( 0.0%) @0x, remaining ??:?? RBU 100.0% UBU 0.0%
0/4698466304 ( 0.0%) @0x, remaining ??:?? RBU 100.0% UBU 0.0%
0/4698466304 ( 0.0%) @0x, remaining ??:?? RBU 100.0% UBU 0.0%
0/4698466304 ( 0.0%) @0x, remaining ??:?? RBU 100.0% UBU 0.0%
0/4698466304 ( 0.0%) @0x, remaining ??:?? RBU 100.0% UBU 0.0%
0/4698466304 ( 0.0%) @0x, remaining ??:?? RBU 100.0% UBU 0.0%
0/4698466304 ( 0.0%) @0x, remaining ??:?? RBU 100.0% UBU 0.0%
0/4698466304 ( 0.0%) @0x, remaining ??:?? RBU 100.0% UBU 0.0%
0/4698466304 ( 0.0%) @0x, remaining ??:?? RBU 100.0% UBU 0.0%
0/4698466304 ( 0.0%) @0x, remaining ??:?? RBU 100.0% UBU 0.0%
0/4698466304 ( 0.0%) @0x, remaining ??:?? RBU 100.0% UBU 0.0%
0/4698466304 ( 0.0%) @0x, remaining ??:?? RBU 100.0% UBU 0.0%
0/4698466304 ( 0.0%) @0x, remaining ??:?? RBU 100.0% UBU 0.0%
0/4698466304 ( 0.0%) @0x, remaining ??:?? RBU 100.0% UBU 0.0%
0/4698466304 ( 0.0%) @0x, remaining ??:?? RBU 100.0% UBU 0.0%
0/4698466304 ( 0.0%) @0x, remaining ??:?? RBU 100.0% UBU 0.0%
0/4698466304 ( 0.0%) @0x, remaining ??:?? RBU 100.0% UBU 0.0%
0/4698466304 ( 0.0%) @0x, remaining ??:?? RBU 100.0% UBU 0.0%
:-[ WRITE@LBA=0h failed with SK=0h/ASC=00h/ACQ=02h]: Input/output error
:-( write failed: Input/output error
$ dmesg
[423391.552902] end_request: I/O error, dev sr0, sector 0
[423391.552943] Buffer I/O error on device sr0, logical block 0
[423391.554352] end_request: I/O error, dev sr0, sector 0
[423391.554386] Buffer I/O error on device sr0, logical block 0
[423453.060096] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[423453.060149] ata1.00: cmd a0/01:00:00:00:80/00:00:00:00:00/a0 tag 0 dma 32768 out
[423453.060151] cdb 2a 00 00 00 00 00 00 00 10 00 00 00 00 00 00 00
[423453.060152] res 40/00:02:00:18:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
[423453.060284] ata1.00: status: { DRDY }
[423458.100042] ata1: link is slow to respond, please be patient (ready=0)
[423463.080063] ata1: device not ready (errno=-16), forcing hardreset
[423463.080081] ata1: soft resetting link
[423463.300456] ata1.00: configured for UDMA/33
[423463.300488] ata1: EH complete
[423545.000087] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[423545.000139] ata1.00: cmd a0/01:00:00:00:80/00:00:00:00:00/a0 tag 0 dma 32768 out
[423545.000141] cdb 2a 00 00 00 00 00 00 00 10 00 00 00 00 00 00 00
[423545.000143] res 40/00:02:00:18:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
[423545.000274] ata1.00: status: { DRDY }
[423550.040042] ata1: link is slow to respond, please be patient (ready=0)
[423555.020043] ata1: device not ready (errno=-16), forcing hardreset
[423555.020059] ata1: soft resetting link
[423555.240467] ata1.00: configured for UDMA/33
[423555.240499] ata1: EH complete
[-- Attachment #3: lspci_system1.txt --]
[-- Type: text/plain, Size: 22924 bytes --]
00:00.0 0500: 10de:02f0 (rev a2)
Subsystem: 103c:30b5
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [44] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=0 UnitCnt=15 MastHost- DefDir- DUL-
Link Control 0: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b-
Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
Link Control 1: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b-
Link Config 1: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
Revision ID: 1.03
Link Frequency 0: 800MHz
Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-
Link Frequency 1: 800MHz
Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 1: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Error Handling: PFlE+ OFlE+ PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
Prefetchable memory behind bridge Upper: 00-00
Bus Number: 00
Capabilities: [e0] HyperTransport: MSI Mapping Enable+ Fixed-
Mapping Address Base: 00000000fee00000
00:00.1 0500: 10de:02fa (rev a2)
Subsystem: 103c:30b5
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:00.2 0500: 10de:02fe (rev a2)
Subsystem: 103c:30b5
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:00.3 0500: 10de:02f8 (rev a2)
Subsystem: 103c:30b5
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:00.4 0500: 10de:02f9 (rev a2)
Subsystem: 103c:30b5
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.5 0500: 10de:02ff (rev a2)
Subsystem: 103c:30b5
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [44] #00 [00fe]
Capabilities: [fc] #00 [0000]
00:00.6 0500: 10de:027f (rev a2)
Subsystem: 103c:30b5
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:00.7 0500: 10de:027e (rev a2)
Subsystem: 103c:30b5
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:02.0 0604: 10de:02fc (rev a1)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=02, sec-latency=0
Memory behind bridge: b3000000-b30fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Subsystem: 10de:0000
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
Address: 00000000fee0300c Data: 4149
Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed-
Mapping Address Base: 00000000fee00000
Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #2, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <4us
ClockPM- Suprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 0, PowerLimit 0.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn+ PwrFlt+ MRL- PresDet- CmdCplt- HPIrq+ LinkChg+
Control: AttnInd Off, PwrInd On, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100] Virtual Channel <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:03.0 0604: 10de:02fd (rev a1)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=04, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: b4000000-b7ffffff
Prefetchable memory behind bridge: 00000000d0000000-00000000d01fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Subsystem: 10de:0000
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
Address: 00000000fee0300c Data: 4151
Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed-
Mapping Address Base: 00000000fee00000
Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <4us
ClockPM- Suprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 0, PowerLimit 0.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn+ PwrFlt+ MRL- PresDet- CmdCplt- HPIrq+ LinkChg+
Control: AttnInd Off, PwrInd On, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100] Virtual Channel <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:05.0 0300: 10de:0244 (rev a2)
Subsystem: 103c:30b5
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 21
Region 0: Memory at b2000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at c0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at b1000000 (64-bit, non-prefetchable) [size=16M]
[virtual] Expansion ROM at 88000000 [disabled] [size=128K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Kernel driver in use: nvidia
Kernel modules: nvidia, nvidiafb
00:09.0 0500: 10de:0270 (rev a2)
Subsystem: 103c:30b5
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [44] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=9 UnitCnt=15 MastHost- DefDir- DUL-
Link Control 0: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b-
Link Config 0: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
Revision ID: 1.03
Link Frequency 0: 800MHz
Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-
Link Frequency 1: 200MHz
Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Error Handling: PFlE+ OFlE+ PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
Prefetchable memory behind bridge Upper: 00-00
Bus Number: 00
Capabilities: [e0] HyperTransport: MSI Mapping Enable+ Fixed-
Mapping Address Base: 00000000fee00000
00:0a.0 0601: 10de:0260 (rev a3)
Subsystem: 103c:30b5
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:0a.1 0c05: 10de:0264 (rev a3)
Subsystem: 103c:30b5
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 10
Region 4: I/O ports at 3040 [size=64]
Region 5: I/O ports at 3000 [size=64]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: nForce2_smbus
Kernel modules: i2c-nforce2
00:0a.3 0b40: 10de:0271 (rev a3)
Subsystem: 103c:30b5
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 11
Region 0: Memory at b0040000 (32-bit, non-prefetchable) [size=256K]
00:0b.0 0c03: 10de:026d (rev a3) (prog-if 10)
Subsystem: 103c:30b5
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 23
Region 0: Memory at b0004000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:0b.1 0c03: 10de:026e (rev a3) (prog-if 20)
Subsystem: 103c:30b5
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 22
Region 0: Memory at b0005000 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Debug port: BAR=1 offset=0098
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:0d.0 0101: 10de:0265 (rev f1) (prog-if 8a [Master SecP PriP])
Subsystem: 103c:30b5
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
Region 4: I/O ports at 3080 [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pata_amd
Kernel modules: pata_amd, pata_acpi, ata_generic
00:0e.0 0101: 10de:0266 (rev f1) (prog-if 85 [Master SecO PriO])
Subsystem: 103c:30b5
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 30b0 [size=8]
Region 1: I/O ports at 30a4 [size=4]
Region 2: I/O ports at 30a8 [size=8]
Region 3: I/O ports at 30a0 [size=4]
Region 4: I/O ports at 3090 [size=16]
Region 5: Memory at b0006000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/2 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+
Kernel driver in use: sata_nv
Kernel modules: sata_nv, pata_acpi, ata_generic
00:10.0 0604: 10de:026f (rev a2) (prog-if 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=64
Memory behind bridge: b8000000-b80fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
Capabilities: [b8] Subsystem: 0000:0000
Capabilities: [8c] HyperTransport: MSI Mapping Enable- Fixed-
Mapping Address Base: 00000000fee00000
00:10.1 0403: 10de:026c (rev a2)
Subsystem: 103c:30b5
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin B routed to IRQ 22
Region 0: Memory at b0000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [6c] HyperTransport: MSI Mapping Enable- Fixed+
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:14.0 0680: 10de:0269 (rev a3)
Subsystem: 103c:30b5
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 17
Region 0: Memory at b0007000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 30b8 [size=8]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=0 PME-
Kernel driver in use: forcedeth
Kernel modules: forcedeth, isp1760
00:18.0 0600: 1022:1100
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [80] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=8
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
00:18.1 0600: 1022:1101
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.2 0600: 1022:1102
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.3 0600: 1022:1103
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [f0] Secure device <?>
Kernel driver in use: k8temp
Kernel modules: k8temp
01:00.0 0280: 14e4:4312 (rev 01)
Subsystem: 103c:1361
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at b3000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [d0] Express (v1) Legacy Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 <4us, L1 <64us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [13c] Virtual Channel <?>
Kernel driver in use: b43-pci-bridge
Kernel modules: ssb, wl
05:09.0 0c00: 1180:0832 (prog-if 10)
Subsystem: 103c:30b5
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (500ns min, 1000ns max)
Interrupt: pin A routed to IRQ 16
Region 0: Memory at b8000000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME+
Kernel driver in use: ohci1394
Kernel modules: ohci1394
05:09.1 0805: 1180:0822 (rev 19)
Subsystem: 103c:30b5
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin B routed to IRQ 23
Region 0: Memory at b8000800 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: sdhci-pci
Kernel modules: sdhci-pci
05:09.2 0880: 1180:0843 (rev 0a)
Subsystem: 103c:30b5
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 11
Region 0: [virtual] Memory at b8000c00 (32-bit, non-prefetchable) [disabled] [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: ricoh-mmc
Kernel modules: ricoh_mmc
05:09.3 0880: 1180:0592 (rev 05)
Subsystem: 103c:30b5
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 11
Region 0: Memory at b8001000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
05:09.4 0880: 1180:0852 (rev ff) (prog-if ff)
!!! Unknown header type 7f
[-- Attachment #4: lspci_system2.txt --]
[-- Type: text/plain, Size: 15925 bytes --]
00:00.0 0600: 8086:27a0 (rev 03)
Subsystem: 1584:9916
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information <?>
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp
00:02.0 0300: 8086:27a2 (rev 03)
Subsystem: 1584:9916
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at b0080000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at 1800 [size=8]
Region 2: Memory at c0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at b0040000 (32-bit, non-prefetchable) [size=256K]
Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel modules: intelfb
00:02.1 0380: 8086:27a6 (rev 03)
Subsystem: 1584:9916
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at b0100000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1b.0 0403: 8086:27d8 (rev 02)
Subsystem: 1584:9084
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at f0000000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Virtual Channel <?>
Capabilities: [130] Root Complex Link <?>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:1c.0 0604: 8086:27d0 (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=03, sec-latency=0
I/O behind bridge: 0000f000-0000ffff
Memory behind bridge: fac00000-febfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <4us
ClockPM- Suprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
Slot # 2, PowerLimit 6.500000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0100c Data: 41c1
Capabilities: [90] Subsystem: 1584:907b
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.1 0604: 8086:27d2 (rev 02)
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #2, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <4us
ClockPM- Suprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
Slot # 3, PowerLimit 6.500000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0100c Data: 41c9
Capabilities: [90] Subsystem: 1584:907b
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.2 0604: 8086:27d4 (rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
Memory behind bridge: f7000000-f70fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #3, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <4us
ClockPM- Suprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
Slot # 4, PowerLimit 6.500000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0100c Data: 41d1
Capabilities: [90] Subsystem: 1584:907b
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1d.0 0c03: 8086:27c8 (rev 02)
Subsystem: 1584:907b
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at 1820 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 0c03: 8086:27c9 (rev 02)
Subsystem: 1584:907b
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 1840 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 0c03: 8086:27ca (rev 02)
Subsystem: 1584:907b
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 1860 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.3 0c03: 8086:27cb (rev 02)
Subsystem: 1584:907b
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at 1880 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 0c03: 8086:27cc (rev 02) (prog-if 20)
Subsystem: 1584:907b
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f0004000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 0604: 8086:2448 (rev e2) (prog-if 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=06, subordinate=06, sec-latency=32
I/O behind bridge: 00002000-00002fff
Memory behind bridge: f0200000-f02fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Subsystem: 1584:907b
00:1f.0 0601: 8086:27b9 (rev 02)
Subsystem: 1584:907b
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information <?>
Kernel modules: intel-rng, iTCO_wdt
00:1f.1 0101: 8086:27df (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: 1584:907b
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 1810 [size=16]
Kernel driver in use: ata_piix
Kernel modules: ata_piix
00:1f.2 0101: 8086:27c4 (rev 02) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: 1584:907b
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at 18d0 [size=8]
Region 1: I/O ports at 18c4 [size=4]
Region 2: I/O ports at 18c8 [size=8]
Region 3: I/O ports at 18c0 [size=4]
Region 4: I/O ports at 18b0 [size=16]
Region 5: Memory at f0004400 (32-bit, non-prefetchable) [size=1K]
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ata_piix
Kernel modules: ata_piix
00:1f.3 0c05: 8086:27da (rev 02)
Subsystem: 1584:907b
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 10
Region 4: I/O ports at 18e0 [size=32]
Kernel modules: i2c-i801
06:05.0 0200: 10ec:8139 (rev 10)
Subsystem: 1584:9700
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 2000 [size=256]
Region 1: Memory at b0200000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: 8139too
Kernel modules: 8139too, 8139cp
[-- Attachment #5: lspci_system3.txt --]
[-- Type: text/plain, Size: 12496 bytes --]
00:00.0 0600: 10de:01e0 (rev a2)
Subsystem: 147b:1c00
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [40] AGP version 3.0
Status: RQ=32 Iso- ArqSz=2 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=x4
Capabilities: [60] HyperTransport: Host or Secondary Interface
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=8bit MLWO=8bit LWI=8bit LWO=8bit
Revision ID: 0.16
Kernel driver in use: agpgart-nvidia
Kernel modules: nvidia-agp
00:00.1 0500: 10de:01eb (rev a2)
Subsystem: 10de:0c17
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:00.2 0500: 10de:01ee (rev a2)
Subsystem: 10de:0c17
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:00.3 0500: 10de:01ed (rev a2)
Subsystem: 10de:0c17
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:00.4 0500: 10de:01ec (rev a2)
Subsystem: 10de:0c17
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:00.5 0500: 10de:01ef (rev a2)
Subsystem: 10de:0c17
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:01.0 0601: 10de:0060 (rev a3)
Subsystem: 147b:1c00
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [48] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=1 UnitCnt=15 MastHost- DefDir-
Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC+ TXO- <CRCErr=0
Link Config 0: MLWI=8bit MLWO=8bit LWI=8bit LWO=8bit
Link Control 1: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO+ <CRCErr=0
Link Config 1: MLWI=8bit MLWO=8bit LWI=8bit LWO=8bit
Revision ID: 0.00
00:01.1 0c05: 10de:0064 (rev a2)
Subsystem: 147b:1c00
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 12
Region 0: I/O ports at c400 [size=32]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: nForce2_smbus
Kernel modules: i2c-nforce2
00:02.0 0c03: 10de:0067 (rev a3) (prog-if 10)
Subsystem: 147b:1c00
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 21
Region 0: Memory at e1087000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:02.1 0c03: 10de:0067 (rev a3) (prog-if 10)
Subsystem: 147b:1c00
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 20
Region 0: Memory at e1082000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:02.2 0c03: 10de:0068 (rev a3) (prog-if 20)
Subsystem: 147b:1c00
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin C routed to IRQ 22
Region 0: Memory at e1083000 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Debug port: BAR=1 offset=0080
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:04.0 0200: 10de:0066 (rev a1)
Subsystem: 147b:1c00
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at e1086000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at b000 [size=8]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=0 PME-
Kernel driver in use: forcedeth
Kernel modules: forcedeth
00:05.0 0401: 10de:006b (rev a2)
Subsystem: 147b:1c00
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (250ns min, 3000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at e1000000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:06.0 0401: 10de:006a (rev a1)
Subsystem: 147b:1c00
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at b400 [size=256]
Region 1: I/O ports at b800 [size=128]
Region 2: Memory at e1080000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: Intel ICH
Kernel modules: snd-intel8x0
00:08.0 0604: 10de:006c (rev a3)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 00009000-0000afff
Memory behind bridge: df000000-e0ffffff
Prefetchable memory behind bridge: dc000000-dcffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
Kernel modules: shpchp
00:09.0 0101: 10de:0065 (rev a2) (prog-if 8a [Master SecP PriP])
Subsystem: f47b:1c00
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
Region 4: I/O ports at f000 [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pata_amd
Kernel modules: pata_amd
00:0d.0 0c00: 10de:006e (rev a3) (prog-if 10)
Subsystem: 147b:1c00
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 21
Region 0: Memory at e1084000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at e1085000 (32-bit, non-prefetchable) [size=64]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
Kernel driver in use: ohci1394
Kernel modules: ohci1394
00:1e.0 0604: 10de:01e8 (rev a2)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
Memory behind bridge: dd000000-deffffff
Prefetchable memory behind bridge: d0000000-d7ffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Kernel modules: shpchp
01:06.0 0400: 109e:036e (rev 11)
Subsystem: bd11:1200
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 18
Region 0: Memory at dc000000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data <?>
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: bttv
Kernel modules: bttv
01:06.1 0480: 109e:0878 (rev 11)
Subsystem: bd11:1200
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 18
Region 0: Memory at dc001000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data <?>
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: Bt87x
Kernel modules: snd-bt87x
02:00.0 0300: 10de:0282 (rev a1)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at dd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (32-bit, prefetchable) [size=128M]
[virtual] Expansion ROM at de000000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 3.0
Status: RQ=32 Iso- ArqSz=0 Cal=3 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
Kernel modules: nvidiafb
^ permalink raw reply [flat|nested] 8+ messages in thread
* Unable to write dvd+r on 3 systems
@ 2009-02-14 19:14 Richard Jonsson
2009-02-20 17:02 ` Lennart Sorensen
0 siblings, 1 reply; 8+ messages in thread
From: Richard Jonsson @ 2009-02-14 19:14 UTC (permalink / raw)
To: lkml
Resend due to crappy formatting, sorry about that!
It seems I am the last person on earth burning dvd's. I have tried on
three different systems, using a mix of growisofs, xfburn, brasero and
k3b. They all give the same result for their respective system.
On system 1 it takes forever to complete the process. The system is
completely useless while burning. IO wait is 50% and hardIRQ is
10-20%. If audio is playing at the same time it stutters in a way that
it sounds as it's playing slow. Mouse cursor jerks and it takes eons
to even open a new terminal.
On system 2 growisofs will try for half a minute and then fail with a
message in dmesg. The disc isn't even touched. Tried homebuilt
kernel.org kernels from 2.6.25 to current git with no difference. See
attachment "growisofs_system2.txt". I have been able to burn exactly 1
disc in total, which magically started recording immediately.
System 3 burns at decent speed and always reports success, but about
half the time only part of the disc is actually burned. It is visible
to the eye, and it will not work. Tried at 4x too.
I tried to compile older kernels, 2.6.24 wouldn't boot, and older
kernels would not compile on these systems.
System 1 System 2 System 3
System/mainb. HP DV2140eu Advent (noname) Abit NF7-S
Processor Turion TL52-X2 Celeron M420 Athlon 2400+
RAM 2GB 512MB 1GB
DVD-burner HL-DT-ST DVDRAM Slimtype DVDRW Plextor 8x
GMA-4082N hq04 SOSW-833S vs04
OS Ubuntu 8.10 U 8.10 server U 8.10 server
64bit 32bit 32bit
software all above growisofs growisofs, xfburn
I have at this time only tried one make of media (TDK 16x dvd+r):
dvd+rw-mediainfo /dev/dvd
INQUIRY: [HL-DT-ST][DVDRAM GMA-4082N][HQ04]
GET [CURRENT] CONFIGURATION:
Mounted Media: 1Bh, DVD+R
Current Write Speed: 8.0x1385=11080KB/s
Write Speed #0: 8.0x1385=11080KB/s
Write Speed #1: 4.0x1385=5540KB/s
GET [CURRENT] PERFORMANCE:
Write Performance: 3.3x1385=4584KB/s@0 -> 8.0x1385=11092KB/s@2299967
Speed Descriptor#0: 02/2295103 R@3.3x1385=4584KB/s W@8.0x1385=11080KB/s
Speed Descriptor#1: 02/2295103 R@3.3x1385=4584KB/s W@4.0x1385=5540KB/s
READ DVD STRUCTURE[#0h]:
Media Book Type: 00h, DVD-ROM book [revision 0]
Media ID: TDK/003
Legacy lead-out at: 2295104*2KB=4700372992
READ DISC INFORMATION:
Disc status: blank
Number of Sessions: 1
State of Last Session: empty
"Next" Track: 1
Number of Tracks: 1
READ TRACK INFORMATION[#1]:
Track State: blank
Track Start Address: 0*2KB
Next Writable Address: 0*2KB
Free Blocks: 2295104*2KB
Track Size: 2295104*2KB
READ CAPACITY: 0*2048=0
Please cc me as I'm not subscribed, and thanks in advance / Richard
_________________________________________________________________
25 GB gratis lagring på nätet - Skaffa SkyDrive nu!
http://skydrive.live.com
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: Unable to write dvd+r on 3 systems
2009-02-14 18:54 Unable to write dvd+r on 3 systems Richard Jonsson
@ 2009-02-14 21:53 ` Robert Hancock
2009-02-14 22:30 ` Richard Jonsson
0 siblings, 1 reply; 8+ messages in thread
From: Robert Hancock @ 2009-02-14 21:53 UTC (permalink / raw)
To: Richard Jonsson; +Cc: linux-kernel
Richard Jonsson wrote:
>
> It seems I am the last person on earth burning dvd's. I have tried on three different systems, using a mix of growisofs, xfburn, brasero and k3b. They all give the same result for their respective system.
>
> On system 1 it takes forever to complete the process. The system is completely useless while burning. IO wait is 50% and hardIRQ is 10-20%. If audio is playing at the same time it stutters in a way that it sounds as it's playing slow. Mouse cursor jerks and it takes eons to even open a new terminal.
>
> On system 2 growisofs will try for half a minute and then fail with a message in dmesg. The disc isn't even touched. Tried homebuilt kernel.org kernels from 2.6.25 to current git with no difference. See attachment "growisofs_system2.txt". I have been able to burn exactly 1 disc in total, which magically started recording immediately.
>
> System 3 burns at decent speed and always reports success, but about half the time only part of the disc is actually burned. It is visible to the eye, and it will not work. Tried at 4x too.
It sounds like you may have multiple problems. System 1 sounds like
maybe DMA is not being used for some reason, the dmesg output would be
useful. On System 2 it looks like a write timed out, and system 3 is
having burn quality problems. System 1 may have a kernel issue that
should be looked into, but as for the other two, I would tend to suspect
the quality of the discs you are using. There is a lot of crap media out
there, and also some burners don't like discs with media codes that they
don't have preprogrammed burn strategies for.
^ permalink raw reply [flat|nested] 8+ messages in thread
* RE: Unable to write dvd+r on 3 systems
2009-02-14 21:53 ` Robert Hancock
@ 2009-02-14 22:30 ` Richard Jonsson
2009-02-15 2:16 ` Robert Hancock
0 siblings, 1 reply; 8+ messages in thread
From: Richard Jonsson @ 2009-02-14 22:30 UTC (permalink / raw)
To: hancockrwd; +Cc: lkml
[-- Attachment #1: Type: text/plain, Size: 2540 bytes --]
----------------------------------------
> Date: Sat, 14 Feb 2009 15:53:15 -0600
> From: hancockrwd@gmail.com
> To: richard_jonsson@hotmail.com
> CC: linux-kernel@vger.kernel.org
> Subject: Re: Unable to write dvd+r on 3 systems
>
> Richard Jonsson wrote:
>>
>> It seems I am the last person on earth burning dvd's. I have tried on three different systems, using a mix of growisofs, xfburn, brasero and k3b. They all give the same result for their respective system.
>>
>> On system 1 it takes forever to complete the process. The system is completely useless while burning. IO wait is 50% and hardIRQ is 10-20%. If audio is playing at the same time it stutters in a way that it sounds as it's playing slow. Mouse cursor jerks and it takes eons to even open a new terminal.
>>
>> On system 2 growisofs will try for half a minute and then fail with a message in dmesg. The disc isn't even touched. Tried homebuilt kernel.org kernels from 2.6.25 to current git with no difference. See attachment "growisofs_system2.txt". I have been able to burn exactly 1 disc in total, which magically started recording immediately.
>>
>> System 3 burns at decent speed and always reports success, but about half the time only part of the disc is actually burned. It is visible to the eye, and it will not work. Tried at 4x too.
>
> It sounds like you may have multiple problems. System 1 sounds like
> maybe DMA is not being used for some reason, the dmesg output would be
> useful. On System 2 it looks like a write timed out, and system 3 is
> having burn quality problems. System 1 may have a kernel issue that
> should be looked into, but as for the other two, I would tend to suspect
> the quality of the discs you are using. There is a lot of crap media out
> there, and also some burners don't like discs with media codes that they
> don't have preprogrammed burn strategies for.
Thanks for your reply.
System 1 is affected by
http://bugzilla.kernel.org/show_bug.cgi?id=12309
Also, just noticed that it doesn't appear to have udma capability?!
(see attachment).
Regarding system 3, should there not be an error raised or some such?
It appears to complete the process, but halfway through the laser is
cut?
As for the media, I currently use branded discs (tdk), any
recommendations what to shop for?
_________________________________________________________________
Kolla mailen när du är på språng - skaffa Hotmail i mobilen!
http://windowslivemobile.msn.com/BrowserServiceHotmail.aspx?lang=SE-SE
[-- Attachment #2: hdparm_system1.txt --]
[-- Type: text/plain, Size: 1118 bytes --]
/dev/dvd:
Model=HL-DT-ST DVDRAM GMA-4082N , FwRev=HQ04 , SerialNo=K0868EK5201
Config={ Fixed Removeable DTR<=5Mbs DTR>10Mbs nonMagnetic }
RawCHS=0/0/0, TrkSize=0, SectSize=0, ECCbytes=0
BuffType=unknown, BuffSize=0kB, MaxMultSect=0
(maybe): CurCHS=0/0/0, CurSects=0, LBA=yes, LBAsects=0
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 *mdma2
AdvancedPM=no
Drive conforms to: ATA/ATAPI-5 T13 1321D revision 3: ATA/ATAPI-2,3,4,5
* signifies the current active mode
ATAPI CD-ROM, with removable media
Model Number: HL-DT-ST DVDRAM GMA-4082N
Serial Number: K0868EK5201
Firmware Revision: HQ04
Standards:
Likely used CD-ROM ATAPI-1
Configuration:
DRQ response: 50us.
Packet size: 12 bytes
Capabilities:
LBA, IORDY(can be disabled)
DMA: mdma0 mdma1 *mdma2
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
HW reset results:
CBLID- below Vih
Device num = 0
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: Unable to write dvd+r on 3 systems
2009-02-14 22:30 ` Richard Jonsson
@ 2009-02-15 2:16 ` Robert Hancock
0 siblings, 0 replies; 8+ messages in thread
From: Robert Hancock @ 2009-02-15 2:16 UTC (permalink / raw)
To: Richard Jonsson; +Cc: lkml
Richard Jonsson wrote:
>
>
> ----------------------------------------
>> Date: Sat, 14 Feb 2009 15:53:15 -0600
>> From: hancockrwd@gmail.com
>> To: richard_jonsson@hotmail.com
>> CC: linux-kernel@vger.kernel.org
>> Subject: Re: Unable to write dvd+r on 3 systems
>>
>> Richard Jonsson wrote:
>>> It seems I am the last person on earth burning dvd's. I have tried on three different systems, using a mix of growisofs, xfburn, brasero and k3b. They all give the same result for their respective system.
>>>
>>> On system 1 it takes forever to complete the process. The system is completely useless while burning. IO wait is 50% and hardIRQ is 10-20%. If audio is playing at the same time it stutters in a way that it sounds as it's playing slow. Mouse cursor jerks and it takes eons to even open a new terminal.
>>>
>>> On system 2 growisofs will try for half a minute and then fail with a message in dmesg. The disc isn't even touched. Tried homebuilt kernel.org kernels from 2.6.25 to current git with no difference. See attachment "growisofs_system2.txt". I have been able to burn exactly 1 disc in total, which magically started recording immediately.
>>>
>>> System 3 burns at decent speed and always reports success, but about half the time only part of the disc is actually burned. It is visible to the eye, and it will not work. Tried at 4x too.
>> It sounds like you may have multiple problems. System 1 sounds like
>> maybe DMA is not being used for some reason, the dmesg output would be
>> useful. On System 2 it looks like a write timed out, and system 3 is
>> having burn quality problems. System 1 may have a kernel issue that
>> should be looked into, but as for the other two, I would tend to suspect
>> the quality of the discs you are using. There is a lot of crap media out
>> there, and also some burners don't like discs with media codes that they
>> don't have preprogrammed burn strategies for.
>
> Thanks for your reply.
>
> System 1 is affected by
> http://bugzilla.kernel.org/show_bug.cgi?id=12309
Not sure if that is related, that's referring to heavy disk write IO
where yours is CD burning, which is a rather different workload.
> Also, just noticed that it doesn't appear to have udma capability?!
> (see attachment).
Not too unusual for a lot of burners..
>
> Regarding system 3, should there not be an error raised or some such?
> It appears to complete the process, but halfway through the laser is
> cut?
That's up to the drive. If it chooses not to provide an error to the
burning software when something goes wrong, there's not much that can be
done about it. (It's possible the burning software is failing to report
the error, but that isn't usually the case as far as I've seen.)
>
> As for the media, I currently use branded discs (tdk), any
> recommendations what to shop for?
Verbatim (MCC or MKM media code) are the ones I usually use. Anything
made by Taiyo Yuden is fairly well regarded as well. It depends a lot on
what is available in your area..
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: Unable to write dvd+r on 3 systems
2009-02-14 19:14 Richard Jonsson
@ 2009-02-20 17:02 ` Lennart Sorensen
2009-02-22 10:22 ` Richard Jonsson
0 siblings, 1 reply; 8+ messages in thread
From: Lennart Sorensen @ 2009-02-20 17:02 UTC (permalink / raw)
To: Richard Jonsson; +Cc: lkml
On Sat, Feb 14, 2009 at 08:14:37PM +0100, Richard Jonsson wrote:
>
> Resend due to crappy formatting, sorry about that!
>
> It seems I am the last person on earth burning dvd's. I have tried on
> three different systems, using a mix of growisofs, xfburn, brasero and
> k3b. They all give the same result for their respective system.
>
> On system 1 it takes forever to complete the process. The system is
> completely useless while burning. IO wait is 50% and hardIRQ is
> 10-20%. If audio is playing at the same time it stutters in a way that
> it sounds as it's playing slow. Mouse cursor jerks and it takes eons
> to even open a new terminal.
>
> On system 2 growisofs will try for half a minute and then fail with a
> message in dmesg. The disc isn't even touched. Tried homebuilt
> kernel.org kernels from 2.6.25 to current git with no difference. See
> attachment "growisofs_system2.txt". I have been able to burn exactly 1
> disc in total, which magically started recording immediately.
>
> System 3 burns at decent speed and always reports success, but about
> half the time only part of the disc is actually burned. It is visible
> to the eye, and it will not work. Tried at 4x too.
>
> I tried to compile older kernels, 2.6.24 wouldn't boot, and older
> kernels would not compile on these systems.
>
> System 1 System 2 System 3
> System/mainb. HP DV2140eu Advent (noname) Abit NF7-S
> Processor Turion TL52-X2 Celeron M420 Athlon 2400+
> RAM 2GB 512MB 1GB
> DVD-burner HL-DT-ST DVDRAM Slimtype DVDRW Plextor 8x
> GMA-4082N hq04 SOSW-833S vs04
> OS Ubuntu 8.10 U 8.10 server U 8.10 server
> 64bit 32bit 32bit
> software all above growisofs growisofs, xfburn
>
> I have at this time only tried one make of media (TDK 16x dvd+r):
> dvd+rw-mediainfo /dev/dvd
> INQUIRY: [HL-DT-ST][DVDRAM GMA-4082N][HQ04]
> GET [CURRENT] CONFIGURATION:
> Mounted Media: 1Bh, DVD+R
> Current Write Speed: 8.0x1385=11080KB/s
> Write Speed #0: 8.0x1385=11080KB/s
> Write Speed #1: 4.0x1385=5540KB/s
> GET [CURRENT] PERFORMANCE:
> Write Performance: 3.3x1385=4584KB/s@0 -> 8.0x1385=11092KB/s@2299967
> Speed Descriptor#0: 02/2295103 R@3.3x1385=4584KB/s W@8.0x1385=11080KB/s
> Speed Descriptor#1: 02/2295103 R@3.3x1385=4584KB/s W@4.0x1385=5540KB/s
> READ DVD STRUCTURE[#0h]:
> Media Book Type: 00h, DVD-ROM book [revision 0]
> Media ID: TDK/003
> Legacy lead-out at: 2295104*2KB=4700372992
> READ DISC INFORMATION:
> Disc status: blank
> Number of Sessions: 1
> State of Last Session: empty
> "Next" Track: 1
> Number of Tracks: 1
> READ TRACK INFORMATION[#1]:
> Track State: blank
> Track Start Address: 0*2KB
> Next Writable Address: 0*2KB
> Free Blocks: 2295104*2KB
> Track Size: 2295104*2KB
> READ CAPACITY: 0*2048=0
>
> Please cc me as I'm not subscribed, and thanks in advance / Richard
Is anything stupid like gnome volume manager or hal or something regularly
poking at the drive to detect discs?
Are you using 80conductor IDE cables (for those drives that are IDE)?
I have had some DVD writers fail in odd ways when using 40conductor
cables.
--
Len Sorensen
^ permalink raw reply [flat|nested] 8+ messages in thread
* RE: Unable to write dvd+r on 3 systems
2009-02-20 17:02 ` Lennart Sorensen
@ 2009-02-22 10:22 ` Richard Jonsson
2009-02-23 14:50 ` Lennart Sorensen
0 siblings, 1 reply; 8+ messages in thread
From: Richard Jonsson @ 2009-02-22 10:22 UTC (permalink / raw)
To: lsorense; +Cc: lkml
> Is anything stupid like gnome volume manager or hal or something regularly
> poking at the drive to detect discs?
>
They are present on system1, but not the other two. How can I determine if
they interfere?
> Are you using 80conductor IDE cables (for those drives that are IDE)?
> I have had some DVD writers fail in odd ways when using 40conductor
> cables.
>
Yes.
Running "dd if=/dev/dvd of=/dev/null" on a burned disc reports read
error at or around the block where the speed jumps from 2.4x> 4.0x or
from 4.0x> 6.0x.
I had logs for this, but misplaced them =/. Also when jumping to
the next higher speed there is a dip where growisofs reports 0x burn
speed, is that normal?
> --
> Len Sorensen
_________________________________________________________________
Hitta bästa priserna på MSN Shopping!
http://shopping.msn.se/co_16199-msn-shopping.html
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: Unable to write dvd+r on 3 systems
2009-02-22 10:22 ` Richard Jonsson
@ 2009-02-23 14:50 ` Lennart Sorensen
0 siblings, 0 replies; 8+ messages in thread
From: Lennart Sorensen @ 2009-02-23 14:50 UTC (permalink / raw)
To: Richard Jonsson; +Cc: lkml
On Sun, Feb 22, 2009 at 11:22:29AM +0100, Richard Jonsson wrote:
> They are present on system1, but not the other two. How can I determine if
> they interfere?
Well I have seen them interfere in some cases, but maybe it depends on
the version. Given I hate windows popping up and auto mounting when I
insert disks, I get rid of those things in general. At least the volume
manager is just annoying.
> Running "dd if=/dev/dvd of=/dev/null" on a burned disc reports read
> error at or around the block where the speed jumps from 2.4x> 4.0x or
> from 4.0x> 6.0x.
> I had logs for this, but misplaced them =/. Also when jumping to
> the next higher speed there is a dip where growisofs reports 0x burn
> speed, is that normal?
On some drives I have seen that without problems. Hard to say.
Perhaps asking the cdwrite mailing list where the growisofs developers
seem to hang out could get some better ideas. After all they actually
know how this stuff is suppsoed to work.
--
Len Sorensen
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2009-02-23 14:50 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2009-02-14 18:54 Unable to write dvd+r on 3 systems Richard Jonsson
2009-02-14 21:53 ` Robert Hancock
2009-02-14 22:30 ` Richard Jonsson
2009-02-15 2:16 ` Robert Hancock
-- strict thread matches above, loose matches on Subject: below --
2009-02-14 19:14 Richard Jonsson
2009-02-20 17:02 ` Lennart Sorensen
2009-02-22 10:22 ` Richard Jonsson
2009-02-23 14:50 ` Lennart Sorensen
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox