[PATCH 1/3] at91: Basic support for at91sam9g45 series: header files.

[PATCH 1/3] at91: Basic support for at91sam9g45 series: header files.

[Nicolas Ferre]

AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz.
It embedds USB high speed host and device, LCD, DDR2 RAM, and a full set of
peripherals.

Here is the basic header file support for this product series.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
---
 arch/arm/mach-at91/include/mach/at91sam9g45.h      |  138 ++++++++++++++++++
 .../mach-at91/include/mach/at91sam9g45_matrix.h    |  153 ++++++++++++++++++++
 arch/arm/mach-at91/include/mach/cpu.h              |   16 ++
 arch/arm/mach-at91/include/mach/hardware.h         |    2 +
 arch/arm/mach-at91/include/mach/timex.h            |    5 +
 5 files changed, 314 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/mach-at91/include/mach/at91sam9g45.h
 create mode 100644 arch/arm/mach-at91/include/mach/at91sam9g45_matrix.h

diff --git a/arch/arm/mach-at91/include/mach/at91sam9g45.h b/arch/arm/mach-at91/include/mach/at91sam9g45.h
new file mode 100644
index 0000000..2c42cf5
--- /dev/null
+++ b/arch/arm/mach-at91/include/mach/at91sam9g45.h
@@ -0,0 +1,138 @@
+/*
+ * Chip-specific header file for the AT91SAM9G45 family
+ *
+ *  Copyright (C) 2008-2009 Atmel Corporation.
+ *
+ * Common definitions.
+ * Based on AT91SAM9G45 preliminary datasheet.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef AT91SAM9G45_H
+#define AT91SAM9G45_H
+
+/*
+ * Peripheral identifiers/interrupts.
+ */
+#define AT91_ID_FIQ		0	/* Advanced Interrupt Controller (FIQ) */
+#define AT91_ID_SYS		1	/* System Controller Interrupt */
+#define AT91SAM9G45_ID_PIOA	2	/* Parallel I/O Controller A */
+#define AT91SAM9G45_ID_PIOB	3	/* Parallel I/O Controller B */
+#define AT91SAM9G45_ID_PIOC	4	/* Parallel I/O Controller C */
+#define AT91SAM9G45_ID_PIODE	5	/* Parallel I/O Controller D and E */
+#define AT91SAM9G45_ID_TRNG	6	/* True Random Number Generator */
+#define AT91SAM9G45_ID_US0	7	/* USART 0 */
+#define AT91SAM9G45_ID_US1	8	/* USART 1 */
+#define AT91SAM9G45_ID_US2	9	/* USART 2 */
+#define AT91SAM9G45_ID_US3	10	/* USART 3 */
+#define AT91SAM9G45_ID_MCI0	11	/* High Speed Multimedia Card Interface 0 */
+#define AT91SAM9G45_ID_TWI0	12	/* Two-Wire Interface 0 */
+#define AT91SAM9G45_ID_TWI1	13	/* Two-Wire Interface 1 */
+#define AT91SAM9G45_ID_SPI0	14	/* Serial Peripheral Interface 0 */
+#define AT91SAM9G45_ID_SPI1	15	/* Serial Peripheral Interface 1 */
+#define AT91SAM9G45_ID_SSC0	16	/* Synchronous Serial Controller 0 */
+#define AT91SAM9G45_ID_SSC1	17	/* Synchronous Serial Controller 1 */
+#define AT91SAM9G45_ID_TCB	18	/* Timer Counter 0, 1, 2, 3, 4 and 5 */
+#define AT91SAM9G45_ID_PWMC	19	/* Pulse Width Modulation Controller */
+#define AT91SAM9G45_ID_TSC	20	/* Touch Screen ADC Controller */
+#define AT91SAM9G45_ID_DMA	21	/* DMA Controller */
+#define AT91SAM9G45_ID_UHPHS	22	/* USB Host High Speed */
+#define AT91SAM9G45_ID_LCDC	23	/* LCD Controller */
+#define AT91SAM9G45_ID_AC97C	24	/* AC97 Controller */
+#define AT91SAM9G45_ID_EMAC	25	/* Ethernet MAC */
+#define AT91SAM9G45_ID_ISI	26	/* Image Sensor Interface */
+#define AT91SAM9G45_ID_UDPHS	27	/* USB Device High Speed */
+#define AT91SAM9G45_ID_AESTDESSHA 28	/* AES + T-DES + SHA */
+#define AT91SAM9G45_ID_MCI1	29	/* High Speed Multimedia Card Interface 1 */
+#define AT91SAM9G45_ID_VDEC	30	/* Video Decoder */
+#define AT91SAM9G45_ID_IRQ0	31	/* Advanced Interrupt Controller */
+
+/*
+ * User Peripheral physical base addresses.
+ */
+#define AT91SAM9G45_BASE_UDPHS		0xfff78000
+#define AT91SAM9G45_BASE_TCB0		0xfff7c000
+#define AT91SAM9G45_BASE_TC0		0xfff7c000
+#define AT91SAM9G45_BASE_TC1		0xfff7c040
+#define AT91SAM9G45_BASE_TC2		0xfff7c080
+#define AT91SAM9G45_BASE_MCI0		0xfff80000
+#define AT91SAM9G45_BASE_TWI0		0xfff84000
+#define AT91SAM9G45_BASE_TWI1		0xfff88000
+#define AT91SAM9G45_BASE_US0		0xfff8c000
+#define AT91SAM9G45_BASE_US1		0xfff90000
+#define AT91SAM9G45_BASE_US2		0xfff94000
+#define AT91SAM9G45_BASE_US3		0xfff98000
+#define AT91SAM9G45_BASE_SSC0		0xfff9c000
+#define AT91SAM9G45_BASE_SSC1		0xfffa0000
+#define AT91SAM9G45_BASE_SPI0		0xfffa4000
+#define AT91SAM9G45_BASE_SPI1		0xfffa8000
+#define AT91SAM9G45_BASE_AC97C		0xfffac000
+#define AT91SAM9G45_BASE_TSC		0xfffb0000
+#define AT91SAM9G45_BASE_ISI		0xfffb4000
+#define AT91SAM9G45_BASE_PWMC		0xfffb8000
+#define AT91SAM9G45_BASE_EMAC		0xfffbc000
+#define AT91SAM9G45_BASE_AES		0xfffc0000
+#define AT91SAM9G45_BASE_TDES		0xfffc4000
+#define AT91SAM9G45_BASE_SHA		0xfffc8000
+#define AT91SAM9G45_BASE_TRNG		0xfffcc000
+#define AT91SAM9G45_BASE_MCI1		0xfffd0000
+#define AT91SAM9G45_BASE_TCB1		0xfffd4000
+#define AT91SAM9G45_BASE_TC3		0xfffd4000
+#define AT91SAM9G45_BASE_TC4		0xfffd4040
+#define AT91SAM9G45_BASE_TC5		0xfffd4080
+#define AT91_BASE_SYS			0xffffe200
+
+/*
+ * System Peripherals (offset from AT91_BASE_SYS)
+ */
+#define AT91_ECC	(0xffffe200 - AT91_BASE_SYS)
+#define AT91_DDRSDRC1	(0xffffe400 - AT91_BASE_SYS)
+#define AT91_DDRSDRC0	(0xffffe600 - AT91_BASE_SYS)
+#define AT91_SMC	(0xffffe800 - AT91_BASE_SYS)
+#define AT91_MATRIX	(0xffffea00 - AT91_BASE_SYS)
+#define AT91_DMA	(0xffffec00 - AT91_BASE_SYS)
+#define AT91_DBGU	(0xffffee00 - AT91_BASE_SYS)
+#define AT91_AIC	(0xfffff000 - AT91_BASE_SYS)
+#define AT91_PIOA	(0xfffff200 - AT91_BASE_SYS)
+#define AT91_PIOB	(0xfffff400 - AT91_BASE_SYS)
+#define AT91_PIOC	(0xfffff600 - AT91_BASE_SYS)
+#define AT91_PIOD	(0xfffff800 - AT91_BASE_SYS)
+#define AT91_PIOE	(0xfffffa00 - AT91_BASE_SYS)
+#define AT91_PMC	(0xfffffc00 - AT91_BASE_SYS)
+#define AT91_RSTC	(0xfffffd00 - AT91_BASE_SYS)
+#define AT91_SHDWC	(0xfffffd10 - AT91_BASE_SYS)
+#define AT91_RTT	(0xfffffd20 - AT91_BASE_SYS)
+#define AT91_PIT	(0xfffffd30 - AT91_BASE_SYS)
+#define AT91_WDT	(0xfffffd40 - AT91_BASE_SYS)
+#define AT91_GPBR	(0xfffffd60 - AT91_BASE_SYS)
+#define AT91_RTC	(0xfffffdb0 - AT91_BASE_SYS)
+
+#define AT91_USART0	AT91SAM9G45_BASE_US0
+#define AT91_USART1	AT91SAM9G45_BASE_US1
+#define AT91_USART2	AT91SAM9G45_BASE_US2
+#define AT91_USART3	AT91SAM9G45_BASE_US3
+
+/*
+ * Internal Memory.
+ */
+#define AT91SAM9G45_SRAM_BASE	0x00300000	/* Internal SRAM base address */
+#define AT91SAM9G45_SRAM_SIZE	SZ_64K		/* Internal SRAM size (64Kb) */
+
+#define AT91SAM9G45_ROM_BASE	0x00400000	/* Internal ROM base address */
+#define AT91SAM9G45_ROM_SIZE	SZ_64K		/* Internal ROM size (64Kb) */
+
+#define AT91SAM9G45_LCDC_BASE	0x00500000	/* LCD Controller */
+#define AT91SAM9G45_UDPHS_FIFO	0x00600000	/* USB Device HS controller */
+#define AT91SAM9G45_OHCI_BASE	0x00700000	/* USB Host controller (OHCI) */
+#define AT91SAM9G45_EHCI_BASE	0x00800000	/* USB Host controller (EHCI) */
+#define AT91SAM9G45_VDEC_BASE	0x00900000	/* Video Decoder Controller */
+
+#define CONFIG_DRAM_BASE	AT91_CHIPSELECT_6
+
+#define CONSISTENT_DMA_SIZE	SZ_4M
+
+#endif
diff --git a/arch/arm/mach-at91/include/mach/at91sam9g45_matrix.h b/arch/arm/mach-at91/include/mach/at91sam9g45_matrix.h
new file mode 100644
index 0000000..c972d60
--- /dev/null
+++ b/arch/arm/mach-at91/include/mach/at91sam9g45_matrix.h
@@ -0,0 +1,153 @@
+/*
+ * Matrix-centric header file for the AT91SAM9G45 family
+ *
+ *  Copyright (C) 2008-2009 Atmel Corporation.
+ *
+ * Memory Controllers (MATRIX, EBI) - System peripherals registers.
+ * Based on AT91SAM9G45 preliminary datasheet.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef AT91SAM9G45_MATRIX_H
+#define AT91SAM9G45_MATRIX_H
+
+#define AT91_MATRIX_MCFG0	(AT91_MATRIX + 0x00)	/* Master Configuration Register 0 */
+#define AT91_MATRIX_MCFG1	(AT91_MATRIX + 0x04)	/* Master Configuration Register 1 */
+#define AT91_MATRIX_MCFG2	(AT91_MATRIX + 0x08)	/* Master Configuration Register 2 */
+#define AT91_MATRIX_MCFG3	(AT91_MATRIX + 0x0C)	/* Master Configuration Register 3 */
+#define AT91_MATRIX_MCFG4	(AT91_MATRIX + 0x10)	/* Master Configuration Register 4 */
+#define AT91_MATRIX_MCFG5	(AT91_MATRIX + 0x14)	/* Master Configuration Register 5 */
+#define AT91_MATRIX_MCFG6	(AT91_MATRIX + 0x18)	/* Master Configuration Register 6 */
+#define AT91_MATRIX_MCFG7	(AT91_MATRIX + 0x1C)	/* Master Configuration Register 7 */
+#define AT91_MATRIX_MCFG8	(AT91_MATRIX + 0x20)	/* Master Configuration Register 8 */
+#define AT91_MATRIX_MCFG9	(AT91_MATRIX + 0x24)	/* Master Configuration Register 9 */
+#define AT91_MATRIX_MCFG10	(AT91_MATRIX + 0x28)	/* Master Configuration Register 10 */
+#define AT91_MATRIX_MCFG11	(AT91_MATRIX + 0x2C)	/* Master Configuration Register 11 */
+#define		AT91_MATRIX_ULBT	(7 << 0)	/* Undefined Length Burst Type */
+#define			AT91_MATRIX_ULBT_INFINITE	(0 << 0)
+#define			AT91_MATRIX_ULBT_SINGLE		(1 << 0)
+#define			AT91_MATRIX_ULBT_FOUR		(2 << 0)
+#define			AT91_MATRIX_ULBT_EIGHT		(3 << 0)
+#define			AT91_MATRIX_ULBT_SIXTEEN	(4 << 0)
+#define			AT91_MATRIX_ULBT_THIRTYTWO	(5 << 0)
+#define			AT91_MATRIX_ULBT_SIXTYFOUR	(6 << 0)
+#define			AT91_MATRIX_ULBT_128		(7 << 0)
+
+#define AT91_MATRIX_SCFG0	(AT91_MATRIX + 0x40)	/* Slave Configuration Register 0 */
+#define AT91_MATRIX_SCFG1	(AT91_MATRIX + 0x44)	/* Slave Configuration Register 1 */
+#define AT91_MATRIX_SCFG2	(AT91_MATRIX + 0x48)	/* Slave Configuration Register 2 */
+#define AT91_MATRIX_SCFG3	(AT91_MATRIX + 0x4C)	/* Slave Configuration Register 3 */
+#define AT91_MATRIX_SCFG4	(AT91_MATRIX + 0x50)	/* Slave Configuration Register 4 */
+#define AT91_MATRIX_SCFG5	(AT91_MATRIX + 0x54)	/* Slave Configuration Register 5 */
+#define AT91_MATRIX_SCFG6	(AT91_MATRIX + 0x58)	/* Slave Configuration Register 6 */
+#define AT91_MATRIX_SCFG7	(AT91_MATRIX + 0x5C)	/* Slave Configuration Register 7 */
+#define		AT91_MATRIX_SLOT_CYCLE		(0x1ff << 0)	/* Maximum Number of Allowed Cycles for a Burst */
+#define		AT91_MATRIX_DEFMSTR_TYPE	(3    << 16)	/* Default Master Type */
+#define			AT91_MATRIX_DEFMSTR_TYPE_NONE	(0 << 16)
+#define			AT91_MATRIX_DEFMSTR_TYPE_LAST	(1 << 16)
+#define			AT91_MATRIX_DEFMSTR_TYPE_FIXED	(2 << 16)
+#define		AT91_MATRIX_FIXED_DEFMSTR	(0xf  << 18)	/* Fixed Index of Default Master */
+
+#define AT91_MATRIX_PRAS0	(AT91_MATRIX + 0x80)	/* Priority Register A for Slave 0 */
+#define AT91_MATRIX_PRBS0	(AT91_MATRIX + 0x84)	/* Priority Register B for Slave 0 */
+#define AT91_MATRIX_PRAS1	(AT91_MATRIX + 0x88)	/* Priority Register A for Slave 1 */
+#define AT91_MATRIX_PRBS1	(AT91_MATRIX + 0x8C)	/* Priority Register B for Slave 1 */
+#define AT91_MATRIX_PRAS2	(AT91_MATRIX + 0x90)	/* Priority Register A for Slave 2 */
+#define AT91_MATRIX_PRBS2	(AT91_MATRIX + 0x94)	/* Priority Register B for Slave 2 */
+#define AT91_MATRIX_PRAS3	(AT91_MATRIX + 0x98)	/* Priority Register A for Slave 3 */
+#define AT91_MATRIX_PRBS3	(AT91_MATRIX + 0x9C)	/* Priority Register B for Slave 3 */
+#define AT91_MATRIX_PRAS4	(AT91_MATRIX + 0xA0)	/* Priority Register A for Slave 4 */
+#define AT91_MATRIX_PRBS4	(AT91_MATRIX + 0xA4)	/* Priority Register B for Slave 4 */
+#define AT91_MATRIX_PRAS5	(AT91_MATRIX + 0xA8)	/* Priority Register A for Slave 5 */
+#define AT91_MATRIX_PRBS5	(AT91_MATRIX + 0xAC)	/* Priority Register B for Slave 5 */
+#define AT91_MATRIX_PRAS6	(AT91_MATRIX + 0xB0)	/* Priority Register A for Slave 6 */
+#define AT91_MATRIX_PRBS6	(AT91_MATRIX + 0xB4)	/* Priority Register B for Slave 6 */
+#define AT91_MATRIX_PRAS7	(AT91_MATRIX + 0xB8)	/* Priority Register A for Slave 7 */
+#define AT91_MATRIX_PRBS7	(AT91_MATRIX + 0xBC)	/* Priority Register B for Slave 7 */
+#define		AT91_MATRIX_M0PR		(3 << 0)	/* Master 0 Priority */
+#define		AT91_MATRIX_M1PR		(3 << 4)	/* Master 1 Priority */
+#define		AT91_MATRIX_M2PR		(3 << 8)	/* Master 2 Priority */
+#define		AT91_MATRIX_M3PR		(3 << 12)	/* Master 3 Priority */
+#define		AT91_MATRIX_M4PR		(3 << 16)	/* Master 4 Priority */
+#define		AT91_MATRIX_M5PR		(3 << 20)	/* Master 5 Priority */
+#define		AT91_MATRIX_M6PR		(3 << 24)	/* Master 6 Priority */
+#define		AT91_MATRIX_M7PR		(3 << 28)	/* Master 7 Priority */
+#define		AT91_MATRIX_M8PR		(3 << 0)	/* Master 8 Priority (in Register B) */
+#define		AT91_MATRIX_M9PR		(3 << 4)	/* Master 9 Priority (in Register B) */
+#define		AT91_MATRIX_M10PR		(3 << 8)	/* Master 10 Priority (in Register B) */
+#define		AT91_MATRIX_M11PR		(3 << 12)	/* Master 11 Priority (in Register B) */
+
+#define AT91_MATRIX_MRCR	(AT91_MATRIX + 0x100)	/* Master Remap Control Register */
+#define		AT91_MATRIX_RCB0		(1 << 0)	/* Remap Command for AHB Master 0 (ARM926EJ-S Instruction Master) */
+#define		AT91_MATRIX_RCB1		(1 << 1)	/* Remap Command for AHB Master 1 (ARM926EJ-S Data Master) */
+#define		AT91_MATRIX_RCB2		(1 << 2)
+#define		AT91_MATRIX_RCB3		(1 << 3)
+#define		AT91_MATRIX_RCB4		(1 << 4)
+#define		AT91_MATRIX_RCB5		(1 << 5)
+#define		AT91_MATRIX_RCB6		(1 << 6)
+#define		AT91_MATRIX_RCB7		(1 << 7)
+#define		AT91_MATRIX_RCB8		(1 << 8)
+#define		AT91_MATRIX_RCB9		(1 << 9)
+#define		AT91_MATRIX_RCB10		(1 << 10)
+#define		AT91_MATRIX_RCB11		(1 << 11)
+
+#define AT91_MATRIX_TCMR	(AT91_MATRIX + 0x110)	/* TCM Configuration Register */
+#define		AT91_MATRIX_ITCM_SIZE		(0xf << 0)	/* Size of ITCM enabled memory block */
+#define			AT91_MATRIX_ITCM_0		(0 << 0)
+#define			AT91_MATRIX_ITCM_32		(6 << 0)
+#define		AT91_MATRIX_DTCM_SIZE		(0xf << 4)	/* Size of DTCM enabled memory block */
+#define			AT91_MATRIX_DTCM_0		(0 << 4)
+#define			AT91_MATRIX_DTCM_32		(6 << 4)
+#define			AT91_MATRIX_DTCM_64		(7 << 4)
+#define		AT91_MATRIX_TCM_NWS		(0x1 << 11)	/* Wait state TCM register */
+#define			AT91_MATRIX_TCM_NO_WS		(0x0 << 11)
+#define			AT91_MATRIX_TCM_ONE_WS		(0x1 << 11)
+
+#define AT91_MATRIX_VIDEO	(AT91_MATRIX + 0x118)	/* Video Mode Configuration Register */
+#define		AT91C_VDEC_SEL			(0x1 <<  0) /* Video Mode Selection */
+#define			AT91C_VDEC_SEL_OFF		(0 << 0)
+#define			AT91C_VDEC_SEL_ON		(1 << 0)
+
+#define AT91_MATRIX_EBICSA	(AT91_MATRIX + 0x128)	/* EBI Chip Select Assignment Register */
+#define		AT91_MATRIX_EBI_CS1A		(1 << 1)	/* Chip Select 1 Assignment */
+#define			AT91_MATRIX_EBI_CS1A_SMC		(0 << 1)
+#define			AT91_MATRIX_EBI_CS1A_SDRAMC		(1 << 1)
+#define		AT91_MATRIX_EBI_CS3A		(1 << 3)	/* Chip Select 3 Assignment */
+#define			AT91_MATRIX_EBI_CS3A_SMC		(0 << 3)
+#define			AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA	(1 << 3)
+#define		AT91_MATRIX_EBI_CS4A		(1 << 4)	/* Chip Select 4 Assignment */
+#define			AT91_MATRIX_EBI_CS4A_SMC		(0 << 4)
+#define			AT91_MATRIX_EBI_CS4A_SMC_CF0		(1 << 4)
+#define		AT91_MATRIX_EBI_CS5A		(1 << 5)	/* Chip Select 5 Assignment */
+#define			AT91_MATRIX_EBI_CS5A_SMC		(0 << 5)
+#define			AT91_MATRIX_EBI_CS5A_SMC_CF1		(1 << 5)
+#define		AT91_MATRIX_EBI_DBPUC		(1 << 8)	/* Data Bus Pull-up Configuration */
+#define			AT91_MATRIX_EBI_DBPU_ON			(0 << 8)
+#define			AT91_MATRIX_EBI_DBPU_OFF		(1 << 8)
+#define		AT91_MATRIX_EBI_VDDIOMSEL	(1 << 16)	/* Memory voltage selection */
+#define			AT91_MATRIX_EBI_VDDIOMSEL_1_8V		(0 << 16)
+#define			AT91_MATRIX_EBI_VDDIOMSEL_3_3V		(1 << 16)
+#define		AT91_MATRIX_EBI_EBI_IOSR	(1 << 17)	/* EBI I/O slew rate selection */
+#define			AT91_MATRIX_EBI_EBI_IOSR_REDUCED	(0 << 17)
+#define			AT91_MATRIX_EBI_EBI_IOSR_NORMAL		(1 << 17)
+#define		AT91_MATRIX_EBI_DDR_IOSR	(1 << 18)	/* DDR2 dedicated port I/O slew rate selection */
+#define			AT91_MATRIX_EBI_DDR_IOSR_REDUCED	(0 << 18)
+#define			AT91_MATRIX_EBI_DDR_IOSR_NORMAL		(1 << 18)
+
+#define AT91_MATRIX_WPMR	(AT91_MATRIX + 0x1E4)	/* Write Protect Mode Register */
+#define		AT91_MATRIX_WPMR_WPEN		(1 << 0)	/* Write Protect ENable */
+#define			AT91_MATRIX_WPMR_WP_WPDIS		(0 << 0)
+#define			AT91_MATRIX_WPMR_WP_WPEN		(1 << 0)
+#define		AT91_MATRIX_WPMR_WPKEY		(0xFFFFFF << 8)	/* Write Protect KEY */
+
+#define AT91_MATRIX_WPSR	(AT91_MATRIX + 0x1E8)	/* Write Protect Status Register */
+#define		AT91_MATRIX_WPSR_WPVS		(1 << 0)	/* Write Protect Violation Status */
+#define			AT91_MATRIX_WPSR_NO_WPV		(0 << 0)
+#define			AT91_MATRIX_WPSR_WPV		(1 << 0)
+#define		AT91_MATRIX_WPSR_WPVSRC		(0xFFFF << 8)	/* Write Protect Violation Source */
+
+#endif
diff --git a/arch/arm/mach-at91/include/mach/cpu.h b/arch/arm/mach-at91/include/mach/cpu.h
index c554c3e..b73e7bf 100644
--- a/arch/arm/mach-at91/include/mach/cpu.h
+++ b/arch/arm/mach-at91/include/mach/cpu.h
@@ -23,6 +23,7 @@
 #define ARCH_ID_AT91SAM9263	0x019607a0
 #define ARCH_ID_AT91SAM9G20	0x019905a0
 #define ARCH_ID_AT91SAM9RL64	0x019b03a0
+#define ARCH_ID_AT91SAM9G45	0x819b05a0
 #define ARCH_ID_AT91CAP9	0x039A03A0
 
 #define ARCH_ID_AT91SAM9XE128	0x329973a0
@@ -39,6 +40,15 @@ static inline unsigned long at91_cpu_identify(void)
 	return (at91_sys_read(AT91_DBGU_CIDR) & ~AT91_CIDR_VERSION);
 }
 
+#define ARCH_EXID_AT91SAM9M11	0x00000001
+#define ARCH_EXID_AT91SAM9M10	0x00000002
+#define ARCH_EXID_AT91SAM9G45	0x00000004
+
+static inline unsigned long at91_exid_identify(void)
+{
+	return at91_sys_read(AT91_DBGU_EXID);
+}
+
 
 #define ARCH_FAMILY_AT91X92	0x09200000
 #define ARCH_FAMILY_AT91SAM9	0x01900000
@@ -99,6 +109,12 @@ static inline unsigned long at91cap9_rev_identify(void)
 #define cpu_is_at91sam9rl()	(0)
 #endif
 
+#ifdef CONFIG_ARCH_AT91SAM9G45
+#define cpu_is_at91sam9g45()	(at91_cpu_identify() == ARCH_ID_AT91SAM9G45)
+#else
+#define cpu_is_at91sam9g45()	(0)
+#endif
+
 #ifdef CONFIG_ARCH_AT91CAP9
 #define cpu_is_at91cap9()	(at91_cpu_identify() == ARCH_ID_AT91CAP9)
 #define cpu_is_at91cap9_revB()	(at91cap9_rev_identify() == ARCH_REVISION_CAP9_B)
diff --git a/arch/arm/mach-at91/include/mach/hardware.h b/arch/arm/mach-at91/include/mach/hardware.h
index da0b681..f086917 100644
--- a/arch/arm/mach-at91/include/mach/hardware.h
+++ b/arch/arm/mach-at91/include/mach/hardware.h
@@ -26,6 +26,8 @@
 #include <mach/at91sam9263.h>
 #elif defined(CONFIG_ARCH_AT91SAM9RL)
 #include <mach/at91sam9rl.h>
+#elif defined(CONFIG_ARCH_AT91SAM9G45)
+#include <mach/at91sam9g45.h>
 #elif defined(CONFIG_ARCH_AT91CAP9)
 #include <mach/at91cap9.h>
 #elif defined(CONFIG_ARCH_AT91X40)
diff --git a/arch/arm/mach-at91/include/mach/timex.h b/arch/arm/mach-at91/include/mach/timex.h
index d84c994..38f6c42 100644
--- a/arch/arm/mach-at91/include/mach/timex.h
+++ b/arch/arm/mach-at91/include/mach/timex.h
@@ -62,6 +62,11 @@
 #define AT91SAM9_MASTER_CLOCK	132096000
 #define CLOCK_TICK_RATE		(AT91SAM9_MASTER_CLOCK/16)
 
+#elif defined(CONFIG_ARCH_AT91SAM9G45)
+
+#define AT91SAM9_MASTER_CLOCK	133333333
+#define CLOCK_TICK_RATE		(AT91SAM9_MASTER_CLOCK/16)
+
 #elif defined(CONFIG_ARCH_AT91CAP9)
 
 #define AT91CAP9_MASTER_CLOCK	100000000
-- 
1.5.3.7

Re: [PATCH 1/3] at91: Basic support for at91sam9g45 series: header files.

[Nicolas Ferre]

Nicolas Ferre :
> AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz.
> It embedds USB high speed host and device, LCD, DDR2 RAM, and a full set of
> peripherals.

Can I post this patch series to the patch tracking system or there is
more review to be done (first 3 patches) ?

Best regards,
-- 
Nicolas Ferre

Re: [PATCH 2/3] at91: Support for at91sam9g45: clocks management

[Ben Dooks]

On Thu, Jun 04, 2009 at 10:48:01AM +0200, Nicolas Ferre wrote:
> Add the at91sam9g45 series support to the AT91 generic clock file.
> This takes care of the particularities of the PMC for this series.
> It also takes advantage of the management by functionalities of
> those PLLs and clocks.
> 
> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

personally, please don't post between open and subscriber only lists,
this should really only be sent to linux-arm-kernel.

> ---
>  arch/arm/mach-at91/clock.c |   62 ++++++++++++++++++++++++++++++++++++-------
>  1 files changed, 52 insertions(+), 10 deletions(-)
> 
> diff --git a/arch/arm/mach-at91/clock.c b/arch/arm/mach-at91/clock.c
> index bac578f..6396680 100644
> --- a/arch/arm/mach-at91/clock.c
> +++ b/arch/arm/mach-at91/clock.c
> @@ -47,20 +47,25 @@
>   * Chips have some kind of clocks : group them by functionality
>   */
>  #define cpu_has_utmi()		(  cpu_is_at91cap9() \

how does this pass checkpatch? no spaces after (.

> -				|| cpu_is_at91sam9rl())
> +				|| cpu_is_at91sam9rl() \
> +				|| cpu_is_at91sam9g45())
>  
> -#define cpu_has_800M_plla()	(cpu_is_at91sam9g20())
> +#define cpu_has_800M_plla()	(  cpu_is_at91sam9g20() \
> +				|| cpu_is_at91sam9g45())
>  
> -#define cpu_has_pllb()		(!cpu_is_at91sam9rl())
> +#define cpu_has_300M_plla()	(0)
>  
> -#define cpu_has_upll()		(0)
> +#define cpu_has_pllb()		(!(cpu_is_at91sam9rl() \
> +				|| cpu_is_at91sam9g45()))
> +
> +#define cpu_has_upll()		(cpu_is_at91sam9g45())
>  
>  /* USB host HS & FS */
>  #define cpu_has_uhp()		(!cpu_is_at91sam9rl())
>  
>  /* USB device FS only */
> -#define cpu_has_udpfs()		(!cpu_is_at91sam9rl())
> -
> +#define cpu_has_udpfs()		(!(cpu_is_at91sam9rl() \
> +				|| cpu_is_at91sam9g45()))
>  
>  static LIST_HEAD(clocks);
>  static DEFINE_SPINLOCK(clk_lock);
> @@ -133,6 +138,13 @@ static void pmc_uckr_mode(struct clk *clk, int is_on)
>  {
>  	unsigned int uckr = at91_sys_read(AT91_CKGR_UCKR);
>  
> +	if (cpu_is_at91sam9g45()) {
> +		if (is_on)
> +			uckr |= AT91_PMC_BIASEN;
> +		else
> +			uckr &= ~AT91_PMC_BIASEN;
> +	}
> +
>  	if (is_on) {
>  		is_on = AT91_PMC_LOCKU;
>  		at91_sys_write(AT91_CKGR_UCKR, uckr | clk->pmc_mask);
> @@ -310,6 +322,7 @@ long clk_round_rate(struct clk *clk, unsigned long rate)
>  	unsigned long	flags;
>  	unsigned	prescale;
>  	unsigned long	actual;
> +	unsigned long	prev = ULONG_MAX;
>  
>  	if (!clk_is_programmable(clk))
>  		return -EINVAL;
> @@ -317,8 +330,16 @@ long clk_round_rate(struct clk *clk, unsigned long rate)
>  
>  	actual = clk->parent->rate_hz;
>  	for (prescale = 0; prescale < 7; prescale++) {
> -		if (actual && actual <= rate)
> +		if (actual > rate)
> +			prev = actual;
> +
> +		if (actual && actual <= rate) {
> +			if ((prev - rate) < (rate - actual)) {
> +				actual = prev;
> +				prescale--;
> +			}
>  			break;
> +		}
>  		actual >>= 1;
>  	}
>  
> @@ -373,6 +394,10 @@ int clk_set_parent(struct clk *clk, struct clk *parent)
>  		return -EBUSY;
>  	if (!clk_is_primary(parent) || !clk_is_programmable(clk))
>  		return -EINVAL;
> +
> +	if (cpu_is_at91sam9rl() && parent->id == AT91_PMC_CSS_PLLB)
> +		return -EINVAL;
> +
>  	spin_lock_irqsave(&clk_lock, flags);
>  
>  	clk->rate_hz = parent->rate_hz;
> @@ -637,6 +662,7 @@ int __init at91_clock_init(unsigned long main_clock)
>  {
>  	unsigned tmp, freq, mckr;
>  	int i;
> +	int pll_overclock = false;
>  
>  	/*
>  	 * When the bootloader initialized the main oscillator correctly,
> @@ -654,12 +680,25 @@ int __init at91_clock_init(unsigned long main_clock)
>  
>  	/* report if PLLA is more than mildly overclocked */
>  	plla.rate_hz = at91_pll_rate(&plla, main_clock, at91_sys_read(AT91_CKGR_PLLAR));
> -	if ((!cpu_has_800M_plla() && plla.rate_hz > 209000000)
> -	   || (cpu_has_800M_plla() && plla.rate_hz > 800000000))
> +	if (cpu_has_300M_plla()) {
> +		if (plla.rate_hz > 300000000)
> +			pll_overclock = true;
> +	} else if (cpu_has_800M_plla()) {
> +		if (plla.rate_hz > 800000000)
> +			pll_overclock = true;
> +	} else {
> +		if (plla.rate_hz > 209000000)
> +			pll_overclock = true;
> +	}
> +	if (pll_overclock)
>  		pr_info("Clocks: PLLA overclocked, %ld MHz\n", plla.rate_hz / 1000000);
>  
> +	if (cpu_is_at91sam9g45()) {
> +		mckr = at91_sys_read(AT91_PMC_MCKR);
> +		plla.rate_hz /= (1 << ((mckr & AT91_PMC_PLLADIV2) >> 12));	/* plla divisor by 2 */
> +	}
>  
> -	if (cpu_has_upll() && !cpu_has_pllb()) {
> +	if (!cpu_has_pllb() && cpu_has_upll()) {
>  		/* setup UTMI clock as the fourth primary clock
>  		 * (instead of pllb) */
>  		utmi_clk.type |= CLK_TYPE_PRIMARY;
> @@ -701,6 +740,9 @@ int __init at91_clock_init(unsigned long main_clock)
>  			freq / ((mckr & AT91_PMC_MDIV) >> 7) : freq;	/* mdiv ; (x >> 7) = ((x >> 8) * 2) */
>  		if (mckr & AT91_PMC_PDIV)
>  			freq /= 2;		/* processor clock division */
> +	} else if (cpu_is_at91sam9g45()) {
> +		mck.rate_hz = (mckr & AT91_PMC_MDIV) == AT91SAM9_PMC_MDIV_3 ?
> +			freq / 3 : freq / (1 << ((mckr & AT91_PMC_MDIV) >> 8));	/* mdiv */
>  	} else {
>  		mck.rate_hz = freq / (1 << ((mckr & AT91_PMC_MDIV) >> 8));      /* mdiv */
>  	}

-- 
Ben (ben@fluff.org, http://www.fluff.org/)

  'a smiley only costs 4 bytes'

Re: [PATCH 2/3] at91: Support for at91sam9g45: clocks management

[Nicolas Ferre]

Ben Dooks :
> On Thu, Jun 04, 2009 at 10:48:01AM +0200, Nicolas Ferre wrote:
>> Add the at91sam9g45 series support to the AT91 generic clock file.
>> This takes care of the particularities of the PMC for this series.
>> It also takes advantage of the management by functionalities of
>> those PLLs and clocks.
>>
>> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
> 
> personally, please don't post between open and subscriber only lists,
> this should really only be sent to linux-arm-kernel.

Ah ? Reading SubmittingPatches document, I see in section 6:
"Unless you have a reason NOT to do so, CC linux-kernel@vger.kernel.org"

Is posting in "open" and "subscriber only" lists is a reason?


>> ---
>>  arch/arm/mach-at91/clock.c |   62 ++++++++++++++++++++++++++++++++++++-------
>>  1 files changed, 52 insertions(+), 10 deletions(-)
>>
>> diff --git a/arch/arm/mach-at91/clock.c b/arch/arm/mach-at91/clock.c
>> index bac578f..6396680 100644
>> --- a/arch/arm/mach-at91/clock.c
>> +++ b/arch/arm/mach-at91/clock.c
>> @@ -47,20 +47,25 @@
>>   * Chips have some kind of clocks : group them by functionality
>>   */
>>  #define cpu_has_utmi()		(  cpu_is_at91cap9() \
> 
> how does this pass checkpatch? no spaces after (.

Well, true, it does not. But, have a look at the result, it is so
prettier with those spaces: cpu_is_ directives are aligned.

It's a matter of taste and I considered breaking the rule here was not
so serious...

Thanks Ben.

Regards,
-- 
Nicolas Ferre

[PATCH 2/3] at91: Support for at91sam9g45: clocks management

[Nicolas Ferre]

Add the at91sam9g45 series support to the AT91 generic clock file.
This takes care of the particularities of the PMC for this series.
It also takes advantage of the management by functionalities of
those PLLs and clocks.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
---
 arch/arm/mach-at91/clock.c |   62 ++++++++++++++++++++++++++++++++++++-------
 1 files changed, 52 insertions(+), 10 deletions(-)

diff --git a/arch/arm/mach-at91/clock.c b/arch/arm/mach-at91/clock.c
index bac578f..6396680 100644
--- a/arch/arm/mach-at91/clock.c
+++ b/arch/arm/mach-at91/clock.c
@@ -47,20 +47,25 @@
  * Chips have some kind of clocks : group them by functionality
  */
 #define cpu_has_utmi()		(  cpu_is_at91cap9() \
-				|| cpu_is_at91sam9rl())
+				|| cpu_is_at91sam9rl() \
+				|| cpu_is_at91sam9g45())
 
-#define cpu_has_800M_plla()	(cpu_is_at91sam9g20())
+#define cpu_has_800M_plla()	(  cpu_is_at91sam9g20() \
+				|| cpu_is_at91sam9g45())
 
-#define cpu_has_pllb()		(!cpu_is_at91sam9rl())
+#define cpu_has_300M_plla()	(0)
 
-#define cpu_has_upll()		(0)
+#define cpu_has_pllb()		(!(cpu_is_at91sam9rl() \
+				|| cpu_is_at91sam9g45()))
+
+#define cpu_has_upll()		(cpu_is_at91sam9g45())
 
 /* USB host HS & FS */
 #define cpu_has_uhp()		(!cpu_is_at91sam9rl())
 
 /* USB device FS only */
-#define cpu_has_udpfs()		(!cpu_is_at91sam9rl())
-
+#define cpu_has_udpfs()		(!(cpu_is_at91sam9rl() \
+				|| cpu_is_at91sam9g45()))
 
 static LIST_HEAD(clocks);
 static DEFINE_SPINLOCK(clk_lock);
@@ -133,6 +138,13 @@ static void pmc_uckr_mode(struct clk *clk, int is_on)
 {
 	unsigned int uckr = at91_sys_read(AT91_CKGR_UCKR);
 
+	if (cpu_is_at91sam9g45()) {
+		if (is_on)
+			uckr |= AT91_PMC_BIASEN;
+		else
+			uckr &= ~AT91_PMC_BIASEN;
+	}
+
 	if (is_on) {
 		is_on = AT91_PMC_LOCKU;
 		at91_sys_write(AT91_CKGR_UCKR, uckr | clk->pmc_mask);
@@ -310,6 +322,7 @@ long clk_round_rate(struct clk *clk, unsigned long rate)
 	unsigned long	flags;
 	unsigned	prescale;
 	unsigned long	actual;
+	unsigned long	prev = ULONG_MAX;
 
 	if (!clk_is_programmable(clk))
 		return -EINVAL;
@@ -317,8 +330,16 @@ long clk_round_rate(struct clk *clk, unsigned long rate)
 
 	actual = clk->parent->rate_hz;
 	for (prescale = 0; prescale < 7; prescale++) {
-		if (actual && actual <= rate)
+		if (actual > rate)
+			prev = actual;
+
+		if (actual && actual <= rate) {
+			if ((prev - rate) < (rate - actual)) {
+				actual = prev;
+				prescale--;
+			}
 			break;
+		}
 		actual >>= 1;
 	}
 
@@ -373,6 +394,10 @@ int clk_set_parent(struct clk *clk, struct clk *parent)
 		return -EBUSY;
 	if (!clk_is_primary(parent) || !clk_is_programmable(clk))
 		return -EINVAL;
+
+	if (cpu_is_at91sam9rl() && parent->id == AT91_PMC_CSS_PLLB)
+		return -EINVAL;
+
 	spin_lock_irqsave(&clk_lock, flags);
 
 	clk->rate_hz = parent->rate_hz;
@@ -637,6 +662,7 @@ int __init at91_clock_init(unsigned long main_clock)
 {
 	unsigned tmp, freq, mckr;
 	int i;
+	int pll_overclock = false;
 
 	/*
 	 * When the bootloader initialized the main oscillator correctly,
@@ -654,12 +680,25 @@ int __init at91_clock_init(unsigned long main_clock)
 
 	/* report if PLLA is more than mildly overclocked */
 	plla.rate_hz = at91_pll_rate(&plla, main_clock, at91_sys_read(AT91_CKGR_PLLAR));
-	if ((!cpu_has_800M_plla() && plla.rate_hz > 209000000)
-	   || (cpu_has_800M_plla() && plla.rate_hz > 800000000))
+	if (cpu_has_300M_plla()) {
+		if (plla.rate_hz > 300000000)
+			pll_overclock = true;
+	} else if (cpu_has_800M_plla()) {
+		if (plla.rate_hz > 800000000)
+			pll_overclock = true;
+	} else {
+		if (plla.rate_hz > 209000000)
+			pll_overclock = true;
+	}
+	if (pll_overclock)
 		pr_info("Clocks: PLLA overclocked, %ld MHz\n", plla.rate_hz / 1000000);
 
+	if (cpu_is_at91sam9g45()) {
+		mckr = at91_sys_read(AT91_PMC_MCKR);
+		plla.rate_hz /= (1 << ((mckr & AT91_PMC_PLLADIV2) >> 12));	/* plla divisor by 2 */
+	}
 
-	if (cpu_has_upll() && !cpu_has_pllb()) {
+	if (!cpu_has_pllb() && cpu_has_upll()) {
 		/* setup UTMI clock as the fourth primary clock
 		 * (instead of pllb) */
 		utmi_clk.type |= CLK_TYPE_PRIMARY;
@@ -701,6 +740,9 @@ int __init at91_clock_init(unsigned long main_clock)
 			freq / ((mckr & AT91_PMC_MDIV) >> 7) : freq;	/* mdiv ; (x >> 7) = ((x >> 8) * 2) */
 		if (mckr & AT91_PMC_PDIV)
 			freq /= 2;		/* processor clock division */
+	} else if (cpu_is_at91sam9g45()) {
+		mck.rate_hz = (mckr & AT91_PMC_MDIV) == AT91SAM9_PMC_MDIV_3 ?
+			freq / 3 : freq / (1 << ((mckr & AT91_PMC_MDIV) >> 8));	/* mdiv */
 	} else {
 		mck.rate_hz = freq / (1 << ((mckr & AT91_PMC_MDIV) >> 8));      /* mdiv */
 	}
-- 
1.5.3.7

Re: [PATCH 2/3] at91: Support for at91sam9g45: clocks management

[Nicolas Ferre]

Nicolas Ferre :
> Add the at91sam9g45 series support to the AT91 generic clock file.
> This takes care of the particularities of the PMC for this series.
> It also takes advantage of the management by functionalities of
> those PLLs and clocks.

I must have included in the previous message that the
patch 5438/1 (Applied) is supposed applied on top of current linus' git
tree before this series.

Best regards,
-- 
Nicolas Ferre

[PATCH 3/3] at91: Support for at91sam9g45 series: core chip & board support

[Nicolas Ferre]

Here are the at91 specific files dedicated to the at91sam9g45 series. They
mimic the traditional at91 way of managing chips & boards.

The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES. In
the future, the main board for this 9g45 series will be the
AT91SAM9M10G45-EK (I choose this last name for the board file).

Simple drivers are enabled in _devices and board- files. Newer peripheral
support will be added in future patches.

Incuded peripherals support (for now):
- USART
- SPI
- Ethernet
- NAND flash
- LCD
- gpio/joystick/buttons
- leds and pwm

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
---
 arch/arm/mach-at91/Kconfig               |   26 +-
 arch/arm/mach-at91/Makefile              |    4 +
 arch/arm/mach-at91/Makefile.boot         |    4 +
 arch/arm/mach-at91/at91sam9g45.c         |  360 +++++++++
 arch/arm/mach-at91/at91sam9g45_devices.c | 1230 ++++++++++++++++++++++++++++++
 arch/arm/mach-at91/board-sam9m10g45ek.c  |  389 ++++++++++
 arch/arm/mach-at91/generic.h             |    2 +
 arch/arm/mach-at91/include/mach/board.h  |    8 +-
 drivers/net/Kconfig                      |    2 +-
 drivers/video/Kconfig                    |    2 +-
 10 files changed, 2022 insertions(+), 5 deletions(-)
 create mode 100644 arch/arm/mach-at91/at91sam9g45.c
 create mode 100644 arch/arm/mach-at91/at91sam9g45_devices.c
 create mode 100644 arch/arm/mach-at91/board-sam9m10g45ek.c

diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index 323b47f..22309ba 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -41,6 +41,12 @@ config ARCH_AT91SAM9G20
 	select GENERIC_TIME
 	select GENERIC_CLOCKEVENTS
 
+config ARCH_AT91SAM9G45
+	bool "AT91SAM9G45"
+	select CPU_ARM926T
+	select GENERIC_TIME
+	select GENERIC_CLOCKEVENTS
+
 config ARCH_AT91CAP9
 	bool "AT91CAP9"
 	select CPU_ARM926T
@@ -280,6 +286,22 @@ endif
 
 # ----------------------------------------------------------
 
+if ARCH_AT91SAM9G45
+
+comment "AT91SAM9G45 Board Type"
+
+config MACH_AT91SAM9G45EKES
+	bool "Atmel AT91SAM9G45-EKES Evaluation Kit"
+	depends on ARCH_AT91SAM9G45
+	help
+	  Select this if you are using Atmel's AT91SAM9G45-EKES Evaluation Kit.
+	  "ES" at the end of the name means that this board is an
+	  Engineering Sample.
+
+endif
+
+# ----------------------------------------------------------
+
 if ARCH_AT91CAP9
 
 comment "AT91CAP9 Board Type"
@@ -321,7 +343,7 @@ config MTD_AT91_DATAFLASH_CARD
 
 config MTD_NAND_ATMEL_BUSWIDTH_16
 	bool "Enable 16-bit data bus interface to NAND flash"
-	depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_AT91CAP9ADK)
+	depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_AT91SAM9G45EKES || MACH_AT91CAP9ADK)
 	help
 	  On AT91SAM926x boards both types of NAND flash can be present
 	  (8 and 16 bit data bus width).
@@ -383,7 +405,7 @@ config AT91_EARLY_USART2
 
 config AT91_EARLY_USART3
 	bool "USART3"
-	depends on (ARCH_AT91RM9200 || ARCH_AT91SAM9RL || ARCH_AT91SAM9260 || ARCH_AT91SAM9G20)
+	depends on (ARCH_AT91RM9200 || ARCH_AT91SAM9RL || ARCH_AT91SAM9260 || ARCH_AT91SAM9G20 || ARCH_AT91SAM9G45)
 
 config AT91_EARLY_USART4
 	bool "USART4"
diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile
index c69ff23..2975f9a 100644
--- a/arch/arm/mach-at91/Makefile
+++ b/arch/arm/mach-at91/Makefile
@@ -16,6 +16,7 @@ obj-$(CONFIG_ARCH_AT91SAM9261)	+= at91sam9261.o at91sam926x_time.o at91sam9261_d
 obj-$(CONFIG_ARCH_AT91SAM9263)	+= at91sam9263.o at91sam926x_time.o at91sam9263_devices.o sam9_smc.o
 obj-$(CONFIG_ARCH_AT91SAM9RL)	+= at91sam9rl.o at91sam926x_time.o at91sam9rl_devices.o sam9_smc.o
 obj-$(CONFIG_ARCH_AT91SAM9G20)	+= at91sam9260.o at91sam926x_time.o at91sam9260_devices.o  sam9_smc.o
+ obj-$(CONFIG_ARCH_AT91SAM9G45)	+= at91sam9g45.o at91sam926x_time.o at91sam9g45_devices.o sam9_smc.o
 obj-$(CONFIG_ARCH_AT91CAP9)	+= at91cap9.o at91sam926x_time.o at91cap9_devices.o sam9_smc.o
 obj-$(CONFIG_ARCH_AT91X40)	+= at91x40.o at91x40_time.o
 
@@ -55,6 +56,9 @@ obj-$(CONFIG_MACH_AT91SAM9RLEK)	+= board-sam9rlek.o
 # AT91SAM9G20 board-specific support
 obj-$(CONFIG_MACH_AT91SAM9G20EK) += board-sam9g20ek.o
 
+# AT91SAM9G45 board-specific support
+obj-$(CONFIG_MACH_AT91SAM9G45EKES) += board-sam9m10g45ek.o
+
 # AT91CAP9 board-specific support
 obj-$(CONFIG_MACH_AT91CAP9ADK)	+= board-cap9adk.o
 
diff --git a/arch/arm/mach-at91/Makefile.boot b/arch/arm/mach-at91/Makefile.boot
index 071a250..3462b81 100644
--- a/arch/arm/mach-at91/Makefile.boot
+++ b/arch/arm/mach-at91/Makefile.boot
@@ -7,6 +7,10 @@ ifeq ($(CONFIG_ARCH_AT91CAP9),y)
    zreladdr-y	:= 0x70008000
 params_phys-y	:= 0x70000100
 initrd_phys-y	:= 0x70410000
+else ifeq ($(CONFIG_ARCH_AT91SAM9G45),y)
+   zreladdr-y	:= 0x70008000
+params_phys-y	:= 0x70000100
+initrd_phys-y	:= 0x70410000
 else
    zreladdr-y	:= 0x20008000
 params_phys-y	:= 0x20000100
diff --git a/arch/arm/mach-at91/at91sam9g45.c b/arch/arm/mach-at91/at91sam9g45.c
new file mode 100644
index 0000000..85166b7
--- /dev/null
+++ b/arch/arm/mach-at91/at91sam9g45.c
@@ -0,0 +1,360 @@
+/*
+ *  Chip-specific setup code for the AT91SAM9G45 family
+ *
+ *  Copyright (C) 2009 Atmel Corporation.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/pm.h>
+
+#include <asm/irq.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <mach/at91sam9g45.h>
+#include <mach/at91_pmc.h>
+#include <mach/at91_rstc.h>
+#include <mach/at91_shdwc.h>
+
+#include "generic.h"
+#include "clock.h"
+
+static struct map_desc at91sam9g45_io_desc[] __initdata = {
+	{
+		.virtual	= AT91_VA_BASE_SYS,
+		.pfn		= __phys_to_pfn(AT91_BASE_SYS),
+		.length		= SZ_16K,
+		.type		= MT_DEVICE,
+	}, {
+		.virtual	= AT91_IO_VIRT_BASE - AT91SAM9G45_SRAM_SIZE,
+		.pfn		= __phys_to_pfn(AT91SAM9G45_SRAM_BASE),
+		.length		= AT91SAM9G45_SRAM_SIZE,
+		.type		= MT_DEVICE,
+	}
+};
+
+/* --------------------------------------------------------------------
+ *  Clocks
+ * -------------------------------------------------------------------- */
+
+/*
+ * The peripheral clocks.
+ */
+static struct clk pioA_clk = {
+	.name		= "pioA_clk",
+	.pmc_mask	= 1 << AT91SAM9G45_ID_PIOA,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk pioB_clk = {
+	.name		= "pioB_clk",
+	.pmc_mask	= 1 << AT91SAM9G45_ID_PIOB,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk pioC_clk = {
+	.name		= "pioC_clk",
+	.pmc_mask	= 1 << AT91SAM9G45_ID_PIOC,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk pioDE_clk = {
+	.name		= "pioDE_clk",
+	.pmc_mask	= 1 << AT91SAM9G45_ID_PIODE,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk usart0_clk = {
+	.name		= "usart0_clk",
+	.pmc_mask	= 1 << AT91SAM9G45_ID_US0,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk usart1_clk = {
+	.name		= "usart1_clk",
+	.pmc_mask	= 1 << AT91SAM9G45_ID_US1,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk usart2_clk = {
+	.name		= "usart2_clk",
+	.pmc_mask	= 1 << AT91SAM9G45_ID_US2,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk usart3_clk = {
+	.name		= "usart3_clk",
+	.pmc_mask	= 1 << AT91SAM9G45_ID_US3,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk mmc0_clk = {
+	.name		= "mci0_clk",
+	.pmc_mask	= 1 << AT91SAM9G45_ID_MCI0,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk twi0_clk = {
+	.name		= "twi0_clk",
+	.pmc_mask	= 1 << AT91SAM9G45_ID_TWI0,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk twi1_clk = {
+	.name		= "twi1_clk",
+	.pmc_mask	= 1 << AT91SAM9G45_ID_TWI1,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk spi0_clk = {
+	.name		= "spi0_clk",
+	.pmc_mask	= 1 << AT91SAM9G45_ID_SPI0,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk spi1_clk = {
+	.name		= "spi1_clk",
+	.pmc_mask	= 1 << AT91SAM9G45_ID_SPI1,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk ssc0_clk = {
+	.name		= "ssc0_clk",
+	.pmc_mask	= 1 << AT91SAM9G45_ID_SSC0,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk ssc1_clk = {
+	.name		= "ssc1_clk",
+	.pmc_mask	= 1 << AT91SAM9G45_ID_SSC1,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk tcb_clk = {
+	.name		= "tcb_clk",
+	.pmc_mask	= 1 << AT91SAM9G45_ID_TCB,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk pwm_clk = {
+	.name		= "pwm_clk",
+	.pmc_mask	= 1 << AT91SAM9G45_ID_PWMC,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk tsc_clk = {
+	.name		= "tsc_clk",
+	.pmc_mask	= 1 << AT91SAM9G45_ID_TSC,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk dma_clk = {
+	.name		= "dma_clk",
+	.pmc_mask	= 1 << AT91SAM9G45_ID_DMA,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk uhphs_clk = {
+	.name		= "uhphs_clk",
+	.pmc_mask	= 1 << AT91SAM9G45_ID_UHPHS,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk lcdc_clk = {
+	.name		= "lcdc_clk",
+	.pmc_mask	= 1 << AT91SAM9G45_ID_LCDC,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk ac97_clk = {
+	.name		= "ac97_clk",
+	.pmc_mask	= 1 << AT91SAM9G45_ID_AC97C,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk macb_clk = {
+	.name		= "macb_clk",
+	.pmc_mask	= 1 << AT91SAM9G45_ID_EMAC,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk isi_clk = {
+	.name		= "isi_clk",
+	.pmc_mask	= 1 << AT91SAM9G45_ID_ISI,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk udphs_clk = {
+	.name		= "udphs_clk",
+	.pmc_mask	= 1 << AT91SAM9G45_ID_UDPHS,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk mmc1_clk = {
+	.name		= "mci1_clk",
+	.pmc_mask	= 1 << AT91SAM9G45_ID_MCI1,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+
+/* One additional fake clock for ohci */
+static struct clk ohci_clk = {
+	.name		= "ohci_clk",
+	.pmc_mask	= 0,
+	.type		= CLK_TYPE_PERIPHERAL,
+	.parent		= &uhphs_clk,
+};
+
+static struct clk *periph_clocks[] __initdata = {
+	&pioA_clk,
+	&pioB_clk,
+	&pioC_clk,
+	&pioDE_clk,
+	&usart0_clk,
+	&usart1_clk,
+	&usart2_clk,
+	&usart3_clk,
+	&mmc0_clk,
+	&twi0_clk,
+	&twi1_clk,
+	&spi0_clk,
+	&spi1_clk,
+	&ssc0_clk,
+	&ssc1_clk,
+	&tcb_clk,
+	&pwm_clk,
+	&tsc_clk,
+	&dma_clk,
+	&uhphs_clk,
+	&lcdc_clk,
+	&ac97_clk,
+	&macb_clk,
+	&isi_clk,
+	&udphs_clk,
+	&mmc1_clk,
+	// irq0
+	&ohci_clk,
+};
+
+/*
+ * The two programmable clocks.
+ * You must configure pin multiplexing to bring these signals out.
+ */
+static struct clk pck0 = {
+	.name		= "pck0",
+	.pmc_mask	= AT91_PMC_PCK0,
+	.type		= CLK_TYPE_PROGRAMMABLE,
+	.id		= 0,
+};
+static struct clk pck1 = {
+	.name		= "pck1",
+	.pmc_mask	= AT91_PMC_PCK1,
+	.type		= CLK_TYPE_PROGRAMMABLE,
+	.id		= 1,
+};
+
+static void __init at91sam9g45_register_clocks(void)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(periph_clocks); i++)
+		clk_register(periph_clocks[i]);
+
+	clk_register(&pck0);
+	clk_register(&pck1);
+}
+
+/* --------------------------------------------------------------------
+ *  GPIO
+ * -------------------------------------------------------------------- */
+
+static struct at91_gpio_bank at91sam9g45_gpio[] = {
+	{
+		.id		= AT91SAM9G45_ID_PIOA,
+		.offset		= AT91_PIOA,
+		.clock		= &pioA_clk,
+	}, {
+		.id		= AT91SAM9G45_ID_PIOB,
+		.offset		= AT91_PIOB,
+		.clock		= &pioB_clk,
+	}, {
+		.id		= AT91SAM9G45_ID_PIOC,
+		.offset		= AT91_PIOC,
+		.clock		= &pioC_clk,
+	}, {
+		.id		= AT91SAM9G45_ID_PIODE,
+		.offset		= AT91_PIOD,
+		.clock		= &pioDE_clk,
+	}, {
+		.id		= AT91SAM9G45_ID_PIODE,
+		.offset		= AT91_PIOE,
+		.clock		= &pioDE_clk,
+	}
+};
+
+static void at91sam9g45_reset(void)
+{
+	at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_PROCRST | AT91_RSTC_PERRST);
+}
+
+static void at91sam9g45_poweroff(void)
+{
+	at91_sys_write(AT91_SHDW_CR, AT91_SHDW_KEY | AT91_SHDW_SHDW);
+}
+
+
+/* --------------------------------------------------------------------
+ *  AT91SAM9G45 processor initialization
+ * -------------------------------------------------------------------- */
+
+void __init at91sam9g45_initialize(unsigned long main_clock)
+{
+	/* Map peripherals */
+	iotable_init(at91sam9g45_io_desc, ARRAY_SIZE(at91sam9g45_io_desc));
+
+	at91_arch_reset = at91sam9g45_reset;
+	pm_power_off = at91sam9g45_poweroff;
+	at91_extern_irq = (1 << AT91SAM9G45_ID_IRQ0);
+
+	/* Init clock subsystem */
+	at91_clock_init(main_clock);
+
+	/* Register the processor-specific clocks */
+	at91sam9g45_register_clocks();
+
+	/* Register GPIO subsystem */
+	at91_gpio_init(at91sam9g45_gpio, 5);
+}
+
+/* --------------------------------------------------------------------
+ *  Interrupt initialization
+ * -------------------------------------------------------------------- */
+
+/*
+ * The default interrupt priority levels (0 = lowest, 7 = highest).
+ */
+static unsigned int at91sam9g45_default_irq_priority[NR_AIC_IRQS] __initdata = {
+	7,	/* Advanced Interrupt Controller (FIQ) */
+	7,	/* System Peripherals */
+	1,	/* Parallel IO Controller A */
+	1,	/* Parallel IO Controller B */
+	1,	/* Parallel IO Controller C */
+	1,	/* Parallel IO Controller D and E */
+	0,
+	5,	/* USART 0 */
+	5,	/* USART 1 */
+	5,	/* USART 2 */
+	5,	/* USART 3 */
+	0,	/* Multimedia Card Interface 0 */
+	6,	/* Two-Wire Interface 0 */
+	6,	/* Two-Wire Interface 1 */
+	5,	/* Serial Peripheral Interface 0 */
+	5,	/* Serial Peripheral Interface 1 */
+	4,	/* Serial Synchronous Controller 0 */
+	4,	/* Serial Synchronous Controller 1 */
+	0,	/* Timer Counter 0, 1, 2, 3, 4 and 5 */
+	0,	/* Pulse Width Modulation Controller */
+	0,	/* Touch Screen Controller */
+	0,	/* DMA Controller */
+	2,	/* USB Host High Speed port */
+	3,	/* LDC Controller */
+	5,	/* AC97 Controller */
+	3,	/* Ethernet */
+	0,	/* Image Sensor Interface */
+	2,	/* USB Device High speed port */
+	0,
+	0,	/* Multimedia Card Interface 1 */
+	0,
+	0,	/* Advanced Interrupt Controller (IRQ0) */
+};
+
+void __init at91sam9g45_init_interrupts(unsigned int priority[NR_AIC_IRQS])
+{
+	if (!priority)
+		priority = at91sam9g45_default_irq_priority;
+
+	/* Initialize the AIC interrupt controller */
+	at91_aic_init(priority);
+
+	/* Enable GPIO interrupts */
+	at91_gpio_irq_setup();
+}
diff --git a/arch/arm/mach-at91/at91sam9g45_devices.c b/arch/arm/mach-at91/at91sam9g45_devices.c
new file mode 100644
index 0000000..d746e86
--- /dev/null
+++ b/arch/arm/mach-at91/at91sam9g45_devices.c
@@ -0,0 +1,1230 @@
+/*
+ *  On-Chip devices setup code for the AT91SAM9G45 family
+ *
+ *  Copyright (C) 2009 Atmel Corporation.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ */
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include <linux/dma-mapping.h>
+#include <linux/platform_device.h>
+#include <linux/i2c-gpio.h>
+
+#include <linux/fb.h>
+#include <video/atmel_lcdc.h>
+
+#include <mach/board.h>
+#include <mach/gpio.h>
+#include <mach/at91sam9g45.h>
+#include <mach/at91sam9g45_matrix.h>
+#include <mach/at91sam9_smc.h>
+
+#include "generic.h"
+
+
+/* --------------------------------------------------------------------
+ *  USB Host (OHCI)
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+static u64 ohci_dmamask = DMA_BIT_MASK(32);
+static struct at91_usbh_data usbh_ohci_data;
+
+static struct resource usbh_ohci_resources[] = {
+	[0] = {
+		.start	= AT91SAM9G45_OHCI_BASE,
+		.end	= AT91SAM9G45_OHCI_BASE + SZ_1M - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9G45_ID_UHPHS,
+		.end	= AT91SAM9G45_ID_UHPHS,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91_usbh_ohci_device = {
+	.name		= "at91_ohci",
+	.id		= -1,
+	.dev		= {
+				.dma_mask		= &ohci_dmamask,
+				.coherent_dma_mask	= DMA_BIT_MASK(32),
+				.platform_data		= &usbh_ohci_data,
+	},
+	.resource	= usbh_ohci_resources,
+	.num_resources	= ARRAY_SIZE(usbh_ohci_resources),
+};
+
+void __init at91_add_device_usbh_ohci(struct at91_usbh_data *data)
+{
+	int i;
+
+	if (!data)
+		return;
+
+	/* Enable VBus control for UHP ports */
+	for (i = 0; i < data->ports; i++) {
+		if (data->vbus_pin[i])
+			at91_set_gpio_output(data->vbus_pin[i], 0);
+	}
+
+	usbh_ohci_data = *data;
+	platform_device_register(&at91_usbh_ohci_device);
+}
+#else
+void __init at91_add_device_usbh_ohci(struct at91_usbh_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  USB HS Device (Gadget)
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_USB_GADGET_ATMEL_USBA) || defined(CONFIG_USB_GADGET_ATMEL_USBA_MODULE)
+static struct resource usba_udc_resources[] = {
+	[0] = {
+		.start	= AT91SAM9G45_UDPHS_FIFO,
+		.end	= AT91SAM9G45_UDPHS_FIFO + SZ_512K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9G45_BASE_UDPHS,
+		.end	= AT91SAM9G45_BASE_UDPHS + SZ_1K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[2] = {
+		.start	= AT91SAM9G45_ID_UDPHS,
+		.end	= AT91SAM9G45_ID_UDPHS,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+#define EP(nam, idx, maxpkt, maxbk, dma, isoc)			\
+	[idx] = {						\
+		.name		= nam,				\
+		.index		= idx,				\
+		.fifo_size	= maxpkt,			\
+		.nr_banks	= maxbk,			\
+		.can_dma	= dma,				\
+		.can_isoc	= isoc,				\
+	}
+
+static struct usba_ep_data usba_udc_ep[] __initdata = {
+	EP("ep0", 0, 64, 1, 0, 0),
+	EP("ep1", 1, 1024, 2, 1, 1),
+	EP("ep2", 2, 1024, 2, 1, 1),
+	EP("ep3", 3, 1024, 3, 1, 0),
+	EP("ep4", 4, 1024, 3, 1, 0),
+	EP("ep5", 5, 1024, 3, 1, 1),
+	EP("ep6", 6, 1024, 3, 1, 1),
+};
+
+#undef EP
+
+/*
+ * pdata doesn't have room for any endpoints, so we need to
+ * append room for the ones we need right after it.
+ */
+static struct {
+	struct usba_platform_data pdata;
+	struct usba_ep_data ep[7];
+} usba_udc_data;
+
+static struct platform_device at91_usba_udc_device = {
+	.name		= "atmel_usba_udc",
+	.id		= -1,
+	.dev		= {
+				.platform_data	= &usba_udc_data.pdata,
+	},
+	.resource	= usba_udc_resources,
+	.num_resources	= ARRAY_SIZE(usba_udc_resources),
+};
+
+void __init at91_add_device_usba(struct usba_platform_data *data)
+{
+	usba_udc_data.pdata.vbus_pin = -EINVAL;
+	usba_udc_data.pdata.num_ep = ARRAY_SIZE(usba_udc_ep);
+	memcpy(usba_udc_data.ep, usba_udc_ep, sizeof(usba_udc_ep));;
+
+	if (data && data->vbus_pin > 0) {
+		at91_set_gpio_input(data->vbus_pin, 0);
+		at91_set_deglitch(data->vbus_pin, 1);
+		usba_udc_data.pdata.vbus_pin = data->vbus_pin;
+	}
+
+	/* Pullup pin is handled internally by USB device peripheral */
+
+	/* Clocks */
+	at91_clock_associate("utmi_clk", &at91_usba_udc_device.dev, "hclk");
+	at91_clock_associate("udphs_clk", &at91_usba_udc_device.dev, "pclk");
+
+	platform_device_register(&at91_usba_udc_device);
+}
+#else
+void __init at91_add_device_usba(struct usba_platform_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  Ethernet
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_MACB) || defined(CONFIG_MACB_MODULE)
+static u64 eth_dmamask = DMA_BIT_MASK(32);
+static struct at91_eth_data eth_data;
+
+static struct resource eth_resources[] = {
+	[0] = {
+		.start	= AT91SAM9G45_BASE_EMAC,
+		.end	= AT91SAM9G45_BASE_EMAC + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9G45_ID_EMAC,
+		.end	= AT91SAM9G45_ID_EMAC,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91sam9g45_eth_device = {
+	.name		= "macb",
+	.id		= -1,
+	.dev		= {
+				.dma_mask		= &eth_dmamask,
+				.coherent_dma_mask	= DMA_BIT_MASK(32),
+				.platform_data		= &eth_data,
+	},
+	.resource	= eth_resources,
+	.num_resources	= ARRAY_SIZE(eth_resources),
+};
+
+void __init at91_add_device_eth(struct at91_eth_data *data)
+{
+	if (!data)
+		return;
+
+	if (data->phy_irq_pin) {
+		at91_set_gpio_input(data->phy_irq_pin, 0);
+		at91_set_deglitch(data->phy_irq_pin, 1);
+	}
+
+	/* Pins used for MII and RMII */
+	at91_set_A_periph(AT91_PIN_PA17, 0);	/* ETXCK_EREFCK */
+	at91_set_A_periph(AT91_PIN_PA15, 0);	/* ERXDV */
+	at91_set_A_periph(AT91_PIN_PA12, 0);	/* ERX0 */
+	at91_set_A_periph(AT91_PIN_PA13, 0);	/* ERX1 */
+	at91_set_A_periph(AT91_PIN_PA16, 0);	/* ERXER */
+	at91_set_A_periph(AT91_PIN_PA14, 0);	/* ETXEN */
+	at91_set_A_periph(AT91_PIN_PA10, 0);	/* ETX0 */
+	at91_set_A_periph(AT91_PIN_PA11, 0);	/* ETX1 */
+	at91_set_A_periph(AT91_PIN_PA19, 0);	/* EMDIO */
+	at91_set_A_periph(AT91_PIN_PA18, 0);	/* EMDC */
+
+	if (!data->is_rmii) {
+		at91_set_B_periph(AT91_PIN_PA29, 0);	/* ECRS */
+		at91_set_B_periph(AT91_PIN_PA30, 0);	/* ECOL */
+		at91_set_B_periph(AT91_PIN_PA8,  0);	/* ERX2 */
+		at91_set_B_periph(AT91_PIN_PA9,  0);	/* ERX3 */
+		at91_set_B_periph(AT91_PIN_PA28, 0);	/* ERXCK */
+		at91_set_B_periph(AT91_PIN_PA6,  0);	/* ETX2 */
+		at91_set_B_periph(AT91_PIN_PA7,  0);	/* ETX3 */
+		at91_set_B_periph(AT91_PIN_PA27, 0);	/* ETXER */
+	}
+
+	eth_data = *data;
+	platform_device_register(&at91sam9g45_eth_device);
+}
+#else
+void __init at91_add_device_eth(struct at91_eth_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  NAND / SmartMedia
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_MTD_NAND_ATMEL) || defined(CONFIG_MTD_NAND_ATMEL_MODULE)
+static struct atmel_nand_data nand_data;
+
+#define NAND_BASE	AT91_CHIPSELECT_3
+
+static struct resource nand_resources[] = {
+	[0] = {
+		.start	= NAND_BASE,
+		.end	= NAND_BASE + SZ_256M - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91_BASE_SYS + AT91_ECC,
+		.end	= AT91_BASE_SYS + AT91_ECC + SZ_512 - 1,
+		.flags	= IORESOURCE_MEM,
+	}
+};
+
+static struct platform_device at91sam9g45_nand_device = {
+	.name		= "atmel_nand",
+	.id		= -1,
+	.dev		= {
+				.platform_data	= &nand_data,
+	},
+	.resource	= nand_resources,
+	.num_resources	= ARRAY_SIZE(nand_resources),
+};
+
+void __init at91_add_device_nand(struct atmel_nand_data *data)
+{
+	unsigned long csa;
+
+	if (!data)
+		return;
+
+	csa = at91_sys_read(AT91_MATRIX_EBICSA);
+	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA);
+
+	/* enable pin */
+	if (data->enable_pin)
+		at91_set_gpio_output(data->enable_pin, 1);
+
+	/* ready/busy pin */
+	if (data->rdy_pin)
+		at91_set_gpio_input(data->rdy_pin, 1);
+
+	/* card detect pin */
+	if (data->det_pin)
+		at91_set_gpio_input(data->det_pin, 1);
+
+	nand_data = *data;
+	platform_device_register(&at91sam9g45_nand_device);
+}
+#else
+void __init at91_add_device_nand(struct atmel_nand_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  TWI (i2c)
+ * -------------------------------------------------------------------- */
+
+/*
+ * Prefer the GPIO code since the TWI controller isn't robust
+ * (gets overruns and underruns under load) and can only issue
+ * repeated STARTs in one scenario (the driver doesn't yet handle them).
+ */
+#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
+static struct i2c_gpio_platform_data pdata_i2c0 = {
+	.sda_pin		= AT91_PIN_PA20,
+	.sda_is_open_drain	= 1,
+	.scl_pin		= AT91_PIN_PA21,
+	.scl_is_open_drain	= 1,
+	.udelay			= 2,		/* ~100 kHz */
+};
+
+static struct platform_device at91sam9g45_twi0_device = {
+	.name			= "i2c-gpio",
+	.id			= 0,
+	.dev.platform_data	= &pdata_i2c0,
+};
+
+static struct i2c_gpio_platform_data pdata_i2c1 = {
+	.sda_pin		= AT91_PIN_PB10,
+	.sda_is_open_drain	= 1,
+	.scl_pin		= AT91_PIN_PB11,
+	.scl_is_open_drain	= 1,
+	.udelay			= 2,		/* ~100 kHz */
+};
+
+static struct platform_device at91sam9g45_twi1_device = {
+	.name			= "i2c-gpio",
+	.id			= 1,
+	.dev.platform_data	= &pdata_i2c1,
+};
+
+void __init at91_add_device_i2c(short i2c_id, struct i2c_board_info *devices, int nr_devices)
+{
+	i2c_register_board_info(i2c_id, devices, nr_devices);
+
+	if (i2c_id == 0) {
+		at91_set_GPIO_periph(AT91_PIN_PA20, 1);		/* TWD (SDA) */
+		at91_set_multi_drive(AT91_PIN_PA20, 1);
+
+		at91_set_GPIO_periph(AT91_PIN_PA21, 1);		/* TWCK (SCL) */
+		at91_set_multi_drive(AT91_PIN_PA21, 1);
+
+		platform_device_register(&at91sam9g45_twi0_device);
+	} else {
+		at91_set_GPIO_periph(AT91_PIN_PB10, 1);		/* TWD (SDA) */
+		at91_set_multi_drive(AT91_PIN_PB10, 1);
+
+		at91_set_GPIO_periph(AT91_PIN_PB11, 1);		/* TWCK (SCL) */
+		at91_set_multi_drive(AT91_PIN_PB11, 1);
+
+		platform_device_register(&at91sam9g45_twi1_device);
+	}
+}
+
+#elif defined(CONFIG_I2C_AT91) || defined(CONFIG_I2C_AT91_MODULE)
+static struct resource twi0_resources[] = {
+	[0] = {
+		.start	= AT91SAM9G45_BASE_TWI0,
+		.end	= AT91SAM9G45_BASE_TWI0 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9G45_ID_TWI0,
+		.end	= AT91SAM9G45_ID_TWI0,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91sam9g45_twi0_device = {
+	.name		= "at91_i2c",
+	.id		= 0,
+	.resource	= twi0_resources,
+	.num_resources	= ARRAY_SIZE(twi0_resources),
+};
+
+static struct resource twi1_resources[] = {
+	[0] = {
+		.start	= AT91SAM9G45_BASE_TWI1,
+		.end	= AT91SAM9G45_BASE_TWI1 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9G45_ID_TWI1,
+		.end	= AT91SAM9G45_ID_TWI1,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91sam9g45_twi1_device = {
+	.name		= "at91_i2c",
+	.id		= 1,
+	.resource	= twi1_resources,
+	.num_resources	= ARRAY_SIZE(twi1_resources),
+};
+
+void __init at91_add_device_i2c(short i2c_id, struct i2c_board_info *devices, int nr_devices)
+{
+	i2c_register_board_info(i2c_id, devices, nr_devices);
+
+	/* pins used for TWI interface */
+	if (i2c_id == 0) {
+		at91_set_A_periph(AT91_PIN_PA20, 0);		/* TWD */
+		at91_set_multi_drive(AT91_PIN_PA20, 1);
+
+		at91_set_A_periph(AT91_PIN_PA21, 0);		/* TWCK */
+		at91_set_multi_drive(AT91_PIN_PA21, 1);
+
+		platform_device_register(&at91sam9g45_twi0_device);
+	} else {
+		at91_set_A_periph(AT91_PIN_PB10, 0);		/* TWD */
+		at91_set_multi_drive(AT91_PIN_PB10, 1);
+
+		at91_set_A_periph(AT91_PIN_PB11, 0);		/* TWCK */
+		at91_set_multi_drive(AT91_PIN_PB11, 1);
+
+		platform_device_register(&at91sam9g45_twi1_device);
+	}
+}
+#else
+void __init at91_add_device_i2c(short i2c_id, struct i2c_board_info *devices, int nr_devices) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  SPI
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
+static u64 spi_dmamask = DMA_BIT_MASK(32);
+
+static struct resource spi0_resources[] = {
+	[0] = {
+		.start	= AT91SAM9G45_BASE_SPI0,
+		.end	= AT91SAM9G45_BASE_SPI0 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9G45_ID_SPI0,
+		.end	= AT91SAM9G45_ID_SPI0,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91sam9g45_spi0_device = {
+	.name		= "atmel_spi",
+	.id		= 0,
+	.dev		= {
+				.dma_mask		= &spi_dmamask,
+				.coherent_dma_mask	= DMA_BIT_MASK(32),
+	},
+	.resource	= spi0_resources,
+	.num_resources	= ARRAY_SIZE(spi0_resources),
+};
+
+static const unsigned spi0_standard_cs[4] = { AT91_PIN_PB3, AT91_PIN_PB18, AT91_PIN_PB19, AT91_PIN_PD27 };
+
+static struct resource spi1_resources[] = {
+	[0] = {
+		.start	= AT91SAM9G45_BASE_SPI1,
+		.end	= AT91SAM9G45_BASE_SPI1 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9G45_ID_SPI1,
+		.end	= AT91SAM9G45_ID_SPI1,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91sam9g45_spi1_device = {
+	.name		= "atmel_spi",
+	.id		= 1,
+	.dev		= {
+				.dma_mask		= &spi_dmamask,
+				.coherent_dma_mask	= DMA_BIT_MASK(32),
+	},
+	.resource	= spi1_resources,
+	.num_resources	= ARRAY_SIZE(spi1_resources),
+};
+
+static const unsigned spi1_standard_cs[4] = { AT91_PIN_PB17, AT91_PIN_PD28, AT91_PIN_PD18, AT91_PIN_PD19 };
+
+void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
+{
+	int i;
+	unsigned long cs_pin;
+	short enable_spi0 = 0;
+	short enable_spi1 = 0;
+
+	/* Choose SPI chip-selects */
+	for (i = 0; i < nr_devices; i++) {
+		if (devices[i].controller_data)
+			cs_pin = (unsigned long) devices[i].controller_data;
+		else if (devices[i].bus_num == 0)
+			cs_pin = spi0_standard_cs[devices[i].chip_select];
+		else
+			cs_pin = spi1_standard_cs[devices[i].chip_select];
+
+		if (devices[i].bus_num == 0)
+			enable_spi0 = 1;
+		else
+			enable_spi1 = 1;
+
+		/* enable chip-select pin */
+		at91_set_gpio_output(cs_pin, 1);
+
+		/* pass chip-select pin to driver */
+		devices[i].controller_data = (void *) cs_pin;
+	}
+
+	spi_register_board_info(devices, nr_devices);
+
+	/* Configure SPI bus(es) */
+	if (enable_spi0) {
+		at91_set_A_periph(AT91_PIN_PB0, 0);	/* SPI0_MISO */
+		at91_set_A_periph(AT91_PIN_PB1, 0);	/* SPI0_MOSI */
+		at91_set_A_periph(AT91_PIN_PB2, 0);	/* SPI0_SPCK */
+
+		at91_clock_associate("spi0_clk", &at91sam9g45_spi0_device.dev, "spi_clk");
+		platform_device_register(&at91sam9g45_spi0_device);
+	}
+	if (enable_spi1) {
+		at91_set_A_periph(AT91_PIN_PB14, 0);	/* SPI1_MISO */
+		at91_set_A_periph(AT91_PIN_PB15, 0);	/* SPI1_MOSI */
+		at91_set_A_periph(AT91_PIN_PB16, 0);	/* SPI1_SPCK */
+
+		at91_clock_associate("spi1_clk", &at91sam9g45_spi1_device.dev, "spi_clk");
+		platform_device_register(&at91sam9g45_spi1_device);
+	}
+}
+#else
+void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  LCD Controller
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
+static u64 lcdc_dmamask = DMA_BIT_MASK(32);
+static struct atmel_lcdfb_info lcdc_data;
+
+static struct resource lcdc_resources[] = {
+	[0] = {
+		.start	= AT91SAM9G45_LCDC_BASE,
+		.end	= AT91SAM9G45_LCDC_BASE + SZ_4K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9G45_ID_LCDC,
+		.end	= AT91SAM9G45_ID_LCDC,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91_lcdc_device = {
+	.name		= "atmel_lcdfb",
+	.id		= 0,
+	.dev		= {
+				.dma_mask		= &lcdc_dmamask,
+				.coherent_dma_mask	= DMA_BIT_MASK(32),
+				.platform_data		= &lcdc_data,
+	},
+	.resource	= lcdc_resources,
+	.num_resources	= ARRAY_SIZE(lcdc_resources),
+};
+
+void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
+{
+	if (!data)
+		return;
+
+	at91_set_A_periph(AT91_PIN_PE0, 0);	/* LCDDPWR */
+
+	at91_set_A_periph(AT91_PIN_PE2, 0);	/* LCDCC */
+	at91_set_A_periph(AT91_PIN_PE3, 0);	/* LCDVSYNC */
+	at91_set_A_periph(AT91_PIN_PE4, 0);	/* LCDHSYNC */
+	at91_set_A_periph(AT91_PIN_PE5, 0);	/* LCDDOTCK */
+	at91_set_A_periph(AT91_PIN_PE6, 0);	/* LCDDEN */
+	at91_set_A_periph(AT91_PIN_PE7, 0);	/* LCDD0 */
+	at91_set_A_periph(AT91_PIN_PE8, 0);	/* LCDD1 */
+	at91_set_A_periph(AT91_PIN_PE9, 0);	/* LCDD2 */
+	at91_set_A_periph(AT91_PIN_PE10, 0);	/* LCDD3 */
+	at91_set_A_periph(AT91_PIN_PE11, 0);	/* LCDD4 */
+	at91_set_A_periph(AT91_PIN_PE12, 0);	/* LCDD5 */
+	at91_set_A_periph(AT91_PIN_PE13, 0);	/* LCDD6 */
+	at91_set_A_periph(AT91_PIN_PE14, 0);	/* LCDD7 */
+	at91_set_A_periph(AT91_PIN_PE15, 0);	/* LCDD8 */
+	at91_set_A_periph(AT91_PIN_PE16, 0);	/* LCDD9 */
+	at91_set_A_periph(AT91_PIN_PE17, 0);	/* LCDD10 */
+	at91_set_A_periph(AT91_PIN_PE18, 0);	/* LCDD11 */
+	at91_set_A_periph(AT91_PIN_PE19, 0);	/* LCDD12 */
+	at91_set_A_periph(AT91_PIN_PE20, 0);	/* LCDD13 */
+	at91_set_A_periph(AT91_PIN_PE21, 0);	/* LCDD14 */
+	at91_set_A_periph(AT91_PIN_PE22, 0);	/* LCDD15 */
+	at91_set_A_periph(AT91_PIN_PE23, 0);	/* LCDD16 */
+	at91_set_A_periph(AT91_PIN_PE24, 0);	/* LCDD17 */
+	at91_set_A_periph(AT91_PIN_PE25, 0);	/* LCDD18 */
+	at91_set_A_periph(AT91_PIN_PE26, 0);	/* LCDD19 */
+	at91_set_A_periph(AT91_PIN_PE27, 0);	/* LCDD20 */
+	at91_set_A_periph(AT91_PIN_PE28, 0);	/* LCDD21 */
+	at91_set_A_periph(AT91_PIN_PE29, 0);	/* LCDD22 */
+	at91_set_A_periph(AT91_PIN_PE30, 0);	/* LCDD23 */
+
+	lcdc_data = *data;
+	platform_device_register(&at91_lcdc_device);
+}
+#else
+void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  Timer/Counter block
+ * -------------------------------------------------------------------- */
+
+#ifdef CONFIG_ATMEL_TCLIB
+static struct resource tcb0_resources[] = {
+	[0] = {
+		.start	= AT91SAM9G45_BASE_TCB0,
+		.end	= AT91SAM9G45_BASE_TCB0 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9G45_ID_TCB,
+		.end	= AT91SAM9G45_ID_TCB,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91sam9g45_tcb0_device = {
+	.name		= "atmel_tcb",
+	.id		= 0,
+	.resource	= tcb0_resources,
+	.num_resources	= ARRAY_SIZE(tcb0_resources),
+};
+
+/* TCB1 begins with TC3 */
+static struct resource tcb1_resources[] = {
+	[0] = {
+		.start	= AT91SAM9G45_BASE_TCB1,
+		.end	= AT91SAM9G45_BASE_TCB1 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9G45_ID_TCB,
+		.end	= AT91SAM9G45_ID_TCB,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91sam9g45_tcb1_device = {
+	.name		= "atmel_tcb",
+	.id		= 1,
+	.resource	= tcb1_resources,
+	.num_resources	= ARRAY_SIZE(tcb1_resources),
+};
+
+static void __init at91_add_device_tc(void)
+{
+	/* this chip has one clock and irq for all six TC channels */
+	at91_clock_associate("tcb_clk", &at91sam9g45_tcb0_device.dev, "t0_clk");
+	platform_device_register(&at91sam9g45_tcb0_device);
+	at91_clock_associate("tcb_clk", &at91sam9g45_tcb1_device.dev, "t0_clk");
+	platform_device_register(&at91sam9g45_tcb1_device);
+}
+#else
+static void __init at91_add_device_tc(void) { }
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  RTC
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_RTC_DRV_AT91RM9200) || defined(CONFIG_RTC_DRV_AT91RM9200_MODULE)
+static struct platform_device at91sam9g45_rtc_device = {
+	.name		= "at91_rtc",
+	.id		= -1,
+	.num_resources	= 0,
+};
+
+static void __init at91_add_device_rtc(void)
+{
+	platform_device_register(&at91sam9g45_rtc_device);
+}
+#else
+static void __init at91_add_device_rtc(void) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  RTT
+ * -------------------------------------------------------------------- */
+
+static struct resource rtt_resources[] = {
+	{
+		.start	= AT91_BASE_SYS + AT91_RTT,
+		.end	= AT91_BASE_SYS + AT91_RTT + SZ_16 - 1,
+		.flags	= IORESOURCE_MEM,
+	}
+};
+
+static struct platform_device at91sam9g45_rtt_device = {
+	.name		= "at91_rtt",
+	.id		= 0,
+	.resource	= rtt_resources,
+	.num_resources	= ARRAY_SIZE(rtt_resources),
+};
+
+static void __init at91_add_device_rtt(void)
+{
+	platform_device_register(&at91sam9g45_rtt_device);
+}
+
+
+/* --------------------------------------------------------------------
+ *  Watchdog
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_AT91SAM9_WATCHDOG) || defined(CONFIG_AT91SAM9_WATCHDOG_MODULE)
+static struct platform_device at91sam9g45_wdt_device = {
+	.name		= "at91_wdt",
+	.id		= -1,
+	.num_resources	= 0,
+};
+
+static void __init at91_add_device_watchdog(void)
+{
+	platform_device_register(&at91sam9g45_wdt_device);
+}
+#else
+static void __init at91_add_device_watchdog(void) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  PWM
+ * --------------------------------------------------------------------*/
+
+#if defined(CONFIG_ATMEL_PWM) || defined(CONFIG_ATMEL_PWM_MODULE)
+static u32 pwm_mask;
+
+static struct resource pwm_resources[] = {
+	[0] = {
+		.start	= AT91SAM9G45_BASE_PWMC,
+		.end	= AT91SAM9G45_BASE_PWMC + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9G45_ID_PWMC,
+		.end	= AT91SAM9G45_ID_PWMC,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91sam9g45_pwm0_device = {
+	.name	= "atmel_pwm",
+	.id	= -1,
+	.dev	= {
+		.platform_data		= &pwm_mask,
+	},
+	.resource	= pwm_resources,
+	.num_resources	= ARRAY_SIZE(pwm_resources),
+};
+
+void __init at91_add_device_pwm(u32 mask)
+{
+	if (mask & (1 << AT91_PWM0))
+		at91_set_B_periph(AT91_PIN_PD24, 1);	/* enable PWM0 */
+
+	if (mask & (1 << AT91_PWM1))
+		at91_set_B_periph(AT91_PIN_PD31, 1);	/* enable PWM1 */
+
+	if (mask & (1 << AT91_PWM2))
+		at91_set_B_periph(AT91_PIN_PD26, 1);	/* enable PWM2 */
+
+	if (mask & (1 << AT91_PWM3))
+		at91_set_B_periph(AT91_PIN_PD0, 1);	/* enable PWM3 */
+
+	pwm_mask = mask;
+
+	platform_device_register(&at91sam9g45_pwm0_device);
+}
+#else
+void __init at91_add_device_pwm(u32 mask) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  SSC -- Synchronous Serial Controller
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_ATMEL_SSC) || defined(CONFIG_ATMEL_SSC_MODULE)
+static u64 ssc0_dmamask = DMA_BIT_MASK(32);
+
+static struct resource ssc0_resources[] = {
+	[0] = {
+		.start	= AT91SAM9G45_BASE_SSC0,
+		.end	= AT91SAM9G45_BASE_SSC0 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9G45_ID_SSC0,
+		.end	= AT91SAM9G45_ID_SSC0,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91sam9g45_ssc0_device = {
+	.name	= "ssc",
+	.id	= 0,
+	.dev	= {
+		.dma_mask		= &ssc0_dmamask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	},
+	.resource	= ssc0_resources,
+	.num_resources	= ARRAY_SIZE(ssc0_resources),
+};
+
+static inline void configure_ssc0_pins(unsigned pins)
+{
+	if (pins & ATMEL_SSC_TF)
+		at91_set_A_periph(AT91_PIN_PD1, 1);
+	if (pins & ATMEL_SSC_TK)
+		at91_set_A_periph(AT91_PIN_PD0, 1);
+	if (pins & ATMEL_SSC_TD)
+		at91_set_A_periph(AT91_PIN_PD2, 1);
+	if (pins & ATMEL_SSC_RD)
+		at91_set_A_periph(AT91_PIN_PD3, 1);
+	if (pins & ATMEL_SSC_RK)
+		at91_set_A_periph(AT91_PIN_PD4, 1);
+	if (pins & ATMEL_SSC_RF)
+		at91_set_A_periph(AT91_PIN_PD5, 1);
+}
+
+static u64 ssc1_dmamask = DMA_BIT_MASK(32);
+
+static struct resource ssc1_resources[] = {
+	[0] = {
+		.start	= AT91SAM9G45_BASE_SSC1,
+		.end	= AT91SAM9G45_BASE_SSC1 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9G45_ID_SSC1,
+		.end	= AT91SAM9G45_ID_SSC1,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91sam9g45_ssc1_device = {
+	.name	= "ssc",
+	.id	= 1,
+	.dev	= {
+		.dma_mask		= &ssc1_dmamask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	},
+	.resource	= ssc1_resources,
+	.num_resources	= ARRAY_SIZE(ssc1_resources),
+};
+
+static inline void configure_ssc1_pins(unsigned pins)
+{
+	if (pins & ATMEL_SSC_TF)
+		at91_set_A_periph(AT91_PIN_PD14, 1);
+	if (pins & ATMEL_SSC_TK)
+		at91_set_A_periph(AT91_PIN_PD12, 1);
+	if (pins & ATMEL_SSC_TD)
+		at91_set_A_periph(AT91_PIN_PD10, 1);
+	if (pins & ATMEL_SSC_RD)
+		at91_set_A_periph(AT91_PIN_PD11, 1);
+	if (pins & ATMEL_SSC_RK)
+		at91_set_A_periph(AT91_PIN_PD13, 1);
+	if (pins & ATMEL_SSC_RF)
+		at91_set_A_periph(AT91_PIN_PD15, 1);
+}
+
+/*
+ * SSC controllers are accessed through library code, instead of any
+ * kind of all-singing/all-dancing driver.  For example one could be
+ * used by a particular I2S audio codec's driver, while another one
+ * on the same system might be used by a custom data capture driver.
+ */
+void __init at91_add_device_ssc(unsigned id, unsigned pins)
+{
+	struct platform_device *pdev;
+
+	/*
+	 * NOTE: caller is responsible for passing information matching
+	 * "pins" to whatever will be using each particular controller.
+	 */
+	switch (id) {
+	case AT91SAM9G45_ID_SSC0:
+		pdev = &at91sam9g45_ssc0_device;
+		configure_ssc0_pins(pins);
+		at91_clock_associate("ssc0_clk", &pdev->dev, "pclk");
+		break;
+	case AT91SAM9G45_ID_SSC1:
+		pdev = &at91sam9g45_ssc1_device;
+		configure_ssc1_pins(pins);
+		at91_clock_associate("ssc1_clk", &pdev->dev, "pclk");
+		break;
+	default:
+		return;
+	}
+
+	platform_device_register(pdev);
+}
+
+#else
+void __init at91_add_device_ssc(unsigned id, unsigned pins) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  UART
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_SERIAL_ATMEL)
+static struct resource dbgu_resources[] = {
+	[0] = {
+		.start	= AT91_VA_BASE_SYS + AT91_DBGU,
+		.end	= AT91_VA_BASE_SYS + AT91_DBGU + SZ_512 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91_ID_SYS,
+		.end	= AT91_ID_SYS,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct atmel_uart_data dbgu_data = {
+	.use_dma_tx	= 0,
+	.use_dma_rx	= 0,
+	.regs		= (void __iomem *)(AT91_VA_BASE_SYS + AT91_DBGU),
+};
+
+static u64 dbgu_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device at91sam9g45_dbgu_device = {
+	.name		= "atmel_usart",
+	.id		= 0,
+	.dev		= {
+				.dma_mask		= &dbgu_dmamask,
+				.coherent_dma_mask	= DMA_BIT_MASK(32),
+				.platform_data		= &dbgu_data,
+	},
+	.resource	= dbgu_resources,
+	.num_resources	= ARRAY_SIZE(dbgu_resources),
+};
+
+static inline void configure_dbgu_pins(void)
+{
+	at91_set_A_periph(AT91_PIN_PB12, 0);		/* DRXD */
+	at91_set_A_periph(AT91_PIN_PB13, 1);		/* DTXD */
+}
+
+static struct resource uart0_resources[] = {
+	[0] = {
+		.start	= AT91SAM9G45_BASE_US0,
+		.end	= AT91SAM9G45_BASE_US0 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9G45_ID_US0,
+		.end	= AT91SAM9G45_ID_US0,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct atmel_uart_data uart0_data = {
+	.use_dma_tx	= 1,
+	.use_dma_rx	= 1,
+};
+
+static u64 uart0_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device at91sam9g45_uart0_device = {
+	.name		= "atmel_usart",
+	.id		= 1,
+	.dev		= {
+				.dma_mask		= &uart0_dmamask,
+				.coherent_dma_mask	= DMA_BIT_MASK(32),
+				.platform_data		= &uart0_data,
+	},
+	.resource	= uart0_resources,
+	.num_resources	= ARRAY_SIZE(uart0_resources),
+};
+
+static inline void configure_usart0_pins(unsigned pins)
+{
+	at91_set_A_periph(AT91_PIN_PB19, 1);		/* TXD0 */
+	at91_set_A_periph(AT91_PIN_PB18, 0);		/* RXD0 */
+
+	if (pins & ATMEL_UART_RTS)
+		at91_set_B_periph(AT91_PIN_PB17, 0);	/* RTS0 */
+	if (pins & ATMEL_UART_CTS)
+		at91_set_B_periph(AT91_PIN_PB15, 0);	/* CTS0 */
+}
+
+static struct resource uart1_resources[] = {
+	[0] = {
+		.start	= AT91SAM9G45_BASE_US1,
+		.end	= AT91SAM9G45_BASE_US1 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9G45_ID_US1,
+		.end	= AT91SAM9G45_ID_US1,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct atmel_uart_data uart1_data = {
+	.use_dma_tx	= 1,
+	.use_dma_rx	= 1,
+};
+
+static u64 uart1_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device at91sam9g45_uart1_device = {
+	.name		= "atmel_usart",
+	.id		= 2,
+	.dev		= {
+				.dma_mask		= &uart1_dmamask,
+				.coherent_dma_mask	= DMA_BIT_MASK(32),
+				.platform_data		= &uart1_data,
+	},
+	.resource	= uart1_resources,
+	.num_resources	= ARRAY_SIZE(uart1_resources),
+};
+
+static inline void configure_usart1_pins(unsigned pins)
+{
+	at91_set_A_periph(AT91_PIN_PB4, 1);		/* TXD1 */
+	at91_set_A_periph(AT91_PIN_PB5, 0);		/* RXD1 */
+
+	if (pins & ATMEL_UART_RTS)
+		at91_set_A_periph(AT91_PIN_PD16, 0);	/* RTS1 */
+	if (pins & ATMEL_UART_CTS)
+		at91_set_A_periph(AT91_PIN_PD17, 0);	/* CTS1 */
+}
+
+static struct resource uart2_resources[] = {
+	[0] = {
+		.start	= AT91SAM9G45_BASE_US2,
+		.end	= AT91SAM9G45_BASE_US2 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9G45_ID_US2,
+		.end	= AT91SAM9G45_ID_US2,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct atmel_uart_data uart2_data = {
+	.use_dma_tx	= 1,
+	.use_dma_rx	= 1,
+};
+
+static u64 uart2_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device at91sam9g45_uart2_device = {
+	.name		= "atmel_usart",
+	.id		= 3,
+	.dev		= {
+				.dma_mask		= &uart2_dmamask,
+				.coherent_dma_mask	= DMA_BIT_MASK(32),
+				.platform_data		= &uart2_data,
+	},
+	.resource	= uart2_resources,
+	.num_resources	= ARRAY_SIZE(uart2_resources),
+};
+
+static inline void configure_usart2_pins(unsigned pins)
+{
+	at91_set_A_periph(AT91_PIN_PB6, 1);		/* TXD2 */
+	at91_set_A_periph(AT91_PIN_PB7, 0);		/* RXD2 */
+
+	if (pins & ATMEL_UART_RTS)
+		at91_set_B_periph(AT91_PIN_PC9, 0);	/* RTS2 */
+	if (pins & ATMEL_UART_CTS)
+		at91_set_B_periph(AT91_PIN_PC11, 0);	/* CTS2 */
+}
+
+static struct resource uart3_resources[] = {
+	[0] = {
+		.start	= AT91SAM9G45_BASE_US3,
+		.end	= AT91SAM9G45_BASE_US3 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9G45_ID_US3,
+		.end	= AT91SAM9G45_ID_US3,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct atmel_uart_data uart3_data = {
+	.use_dma_tx	= 1,
+	.use_dma_rx	= 1,
+};
+
+static u64 uart3_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device at91sam9g45_uart3_device = {
+	.name		= "atmel_usart",
+	.id		= 4,
+	.dev		= {
+				.dma_mask		= &uart3_dmamask,
+				.coherent_dma_mask	= DMA_BIT_MASK(32),
+				.platform_data		= &uart3_data,
+	},
+	.resource	= uart3_resources,
+	.num_resources	= ARRAY_SIZE(uart3_resources),
+};
+
+static inline void configure_usart3_pins(unsigned pins)
+{
+	at91_set_A_periph(AT91_PIN_PB8, 1);		/* TXD3 */
+	at91_set_A_periph(AT91_PIN_PB9, 0);		/* RXD3 */
+
+	if (pins & ATMEL_UART_RTS)
+		at91_set_B_periph(AT91_PIN_PA23, 0);	/* RTS3 */
+	if (pins & ATMEL_UART_CTS)
+		at91_set_B_periph(AT91_PIN_PA24, 0);	/* CTS3 */
+}
+
+static struct platform_device *__initdata at91_uarts[ATMEL_MAX_UART];	/* the UARTs to use */
+struct platform_device *atmel_default_console_device;	/* the serial console device */
+
+void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
+{
+	struct platform_device *pdev;
+
+	switch (id) {
+		case 0:		/* DBGU */
+			pdev = &at91sam9g45_dbgu_device;
+			configure_dbgu_pins();
+			at91_clock_associate("mck", &pdev->dev, "usart");
+			break;
+		case AT91SAM9G45_ID_US0:
+			pdev = &at91sam9g45_uart0_device;
+			configure_usart0_pins(pins);
+			at91_clock_associate("usart0_clk", &pdev->dev, "usart");
+			break;
+		case AT91SAM9G45_ID_US1:
+			pdev = &at91sam9g45_uart1_device;
+			configure_usart1_pins(pins);
+			at91_clock_associate("usart1_clk", &pdev->dev, "usart");
+			break;
+		case AT91SAM9G45_ID_US2:
+			pdev = &at91sam9g45_uart2_device;
+			configure_usart2_pins(pins);
+			at91_clock_associate("usart2_clk", &pdev->dev, "usart");
+			break;
+		case AT91SAM9G45_ID_US3:
+			pdev = &at91sam9g45_uart3_device;
+			configure_usart3_pins(pins);
+			at91_clock_associate("usart3_clk", &pdev->dev, "usart");
+			break;
+		default:
+			return;
+	}
+	pdev->id = portnr;		/* update to mapped ID */
+
+	if (portnr < ATMEL_MAX_UART)
+		at91_uarts[portnr] = pdev;
+}
+
+void __init at91_set_serial_console(unsigned portnr)
+{
+	if (portnr < ATMEL_MAX_UART)
+		atmel_default_console_device = at91_uarts[portnr];
+}
+
+void __init at91_add_device_serial(void)
+{
+	int i;
+
+	for (i = 0; i < ATMEL_MAX_UART; i++) {
+		if (at91_uarts[i])
+			platform_device_register(at91_uarts[i]);
+	}
+
+	if (!atmel_default_console_device)
+		printk(KERN_INFO "AT91: No default serial console defined.\n");
+}
+#else
+void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
+void __init at91_set_serial_console(unsigned portnr) {}
+void __init at91_add_device_serial(void) {}
+#endif
+
+
+/* -------------------------------------------------------------------- */
+/*
+ * These devices are always present and don't need any board-specific
+ * setup.
+ */
+static int __init at91_add_standard_devices(void)
+{
+	at91_add_device_rtc();
+	at91_add_device_rtt();
+	at91_add_device_watchdog();
+	at91_add_device_tc();
+	return 0;
+}
+
+arch_initcall(at91_add_standard_devices);
diff --git a/arch/arm/mach-at91/board-sam9m10g45ek.c b/arch/arm/mach-at91/board-sam9m10g45ek.c
new file mode 100644
index 0000000..b8558ea
--- /dev/null
+++ b/arch/arm/mach-at91/board-sam9m10g45ek.c
@@ -0,0 +1,389 @@
+/*
+ *  Board-specific setup code for the AT91SAM9M10G45 Evaluation Kit family
+ *
+ *  Covers: * AT91SAM9G45-EKES  board
+ *          * AT91SAM9M10G45-EK board
+ *
+ *  Copyright (C) 2009 Atmel Corporation.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/fb.h>
+#include <linux/gpio_keys.h>
+#include <linux/input.h>
+#include <linux/leds.h>
+#include <linux/clk.h>
+
+#include <mach/hardware.h>
+#include <video/atmel_lcdc.h>
+
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <mach/hardware.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
+#include <mach/at91sam9_smc.h>
+#include <mach/at91_shdwc.h>
+
+#include "sam9_smc.h"
+#include "generic.h"
+
+
+static void __init ek_map_io(void)
+{
+	/* Initialize processor: 12.000 MHz crystal */
+	at91sam9g45_initialize(12000000);
+
+	/* DGBU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 not connected on the -EK board */
+	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
+	at91_register_uart(AT91SAM9G45_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
+
+	/* set serial console to ttyS0 (ie, DBGU) */
+	at91_set_serial_console(0);
+}
+
+static void __init ek_init_irq(void)
+{
+	at91sam9g45_init_interrupts(NULL);
+}
+
+
+/*
+ * USB HS Host port (common to OHCI & EHCI)
+ */
+static struct at91_usbh_data __initdata ek_usbh_hs_data = {
+	.ports		= 2,
+	.vbus_pin	= {AT91_PIN_PD1, AT91_PIN_PD3},
+};
+
+
+/*
+ * USB HS Device port
+ */
+static struct usba_platform_data __initdata ek_usba_udc_data = {
+	.vbus_pin	= AT91_PIN_PB19,
+};
+
+
+/*
+ * SPI devices.
+ */
+static struct spi_board_info ek_spi_devices[] = {
+	{	/* DataFlash chip */
+		.modalias	= "mtd_dataflash",
+		.chip_select	= 0,
+		.max_speed_hz	= 15 * 1000 * 1000,
+		.bus_num	= 0,
+	},
+};
+
+
+/*
+ * MACB Ethernet device
+ */
+static struct at91_eth_data __initdata ek_macb_data = {
+	.phy_irq_pin	= AT91_PIN_PD5,
+	.is_rmii	= 1,
+};
+
+
+/*
+ * NAND flash
+ */
+static struct mtd_partition __initdata ek_nand_partition[] = {
+	{
+		.name	= "Partition 1",
+		.offset	= 0,
+		.size	= SZ_64M,
+	},
+	{
+		.name	= "Partition 2",
+		.offset	= MTDPART_OFS_NXTBLK,
+		.size	= MTDPART_SIZ_FULL,
+	},
+};
+
+static struct mtd_partition * __init nand_partitions(int size, int *num_partitions)
+{
+	*num_partitions = ARRAY_SIZE(ek_nand_partition);
+	return ek_nand_partition;
+}
+
+/* det_pin is not connected */
+static struct atmel_nand_data __initdata ek_nand_data = {
+	.ale		= 21,
+	.cle		= 22,
+	.rdy_pin	= AT91_PIN_PC8,
+	.enable_pin	= AT91_PIN_PC14,
+	.partition_info	= nand_partitions,
+#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+	.bus_width_16	= 1,
+#else
+	.bus_width_16	= 0,
+#endif
+};
+
+static struct sam9_smc_config __initdata ek_nand_smc_config = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 2,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 2,
+
+	.ncs_read_pulse		= 4,
+	.nrd_pulse		= 4,
+	.ncs_write_pulse	= 4,
+	.nwe_pulse		= 4,
+
+	.read_cycle		= 7,
+	.write_cycle		= 7,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
+	.tdf_cycles		= 3,
+};
+
+static void __init ek_add_device_nand(void)
+{
+	/* setup bus-width (8 or 16) */
+	if (ek_nand_data.bus_width_16)
+		ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
+	else
+		ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
+
+	/* configure chip-select 3 (NAND) */
+	sam9_smc_configure(3, &ek_nand_smc_config);
+
+	at91_add_device_nand(&ek_nand_data);
+}
+
+
+/*
+ * LCD Controller
+ */
+#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
+static struct fb_videomode at91_tft_vga_modes[] = {
+	{
+		.name           = "LG",
+		.refresh	= 60,
+		.xres		= 480,		.yres		= 272,
+		.pixclock	= KHZ2PICOS(9000),
+
+		.left_margin	= 1,		.right_margin	= 1,
+		.upper_margin	= 40,		.lower_margin	= 1,
+		.hsync_len	= 45,		.vsync_len	= 1,
+
+		.sync		= 0,
+		.vmode		= FB_VMODE_NONINTERLACED,
+	},
+};
+
+static struct fb_monspecs at91fb_default_monspecs = {
+	.manufacturer	= "LG",
+	.monitor        = "LB043WQ1",
+
+	.modedb		= at91_tft_vga_modes,
+	.modedb_len	= ARRAY_SIZE(at91_tft_vga_modes),
+	.hfmin		= 15000,
+	.hfmax		= 17640,
+	.vfmin		= 57,
+	.vfmax		= 67,
+};
+
+#define AT91SAM9G45_DEFAULT_LCDCON2 	(ATMEL_LCDC_MEMOR_LITTLE \
+					| ATMEL_LCDC_DISTYPE_TFT \
+					| ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
+
+/* Driver datas */
+static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
+	.lcdcon_is_backlight		= true,
+	.default_bpp			= 32,
+	.default_dmacon			= ATMEL_LCDC_DMAEN,
+	.default_lcdcon2		= AT91SAM9G45_DEFAULT_LCDCON2,
+	.default_monspecs		= &at91fb_default_monspecs,
+	.guard_time			= 9,
+	.lcd_wiring_mode		= ATMEL_LCDC_WIRING_RGB,
+};
+
+#else
+static struct atmel_lcdfb_info __initdata ek_lcdc_data;
+#endif
+
+
+/*
+ * GPIO Buttons
+ */
+#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+static struct gpio_keys_button ek_buttons[] = {
+	{	/* BP1, "leftclic" */
+		.code		= BTN_LEFT,
+		.gpio		= AT91_PIN_PB6,
+		.active_low	= 1,
+		.desc		= "left_click",
+		.wakeup		= 1,
+	},
+	{	/* BP2, "rightclic" */
+		.code		= BTN_RIGHT,
+		.gpio		= AT91_PIN_PB7,
+		.active_low	= 1,
+		.desc		= "right_click",
+		.wakeup		= 1,
+	},
+		/* BP3, "joystick" */
+	{
+		.code		= KEY_LEFT,
+		.gpio		= AT91_PIN_PB14,
+		.active_low	= 1,
+		.desc		= "Joystick Left",
+	},
+	{
+		.code		= KEY_RIGHT,
+		.gpio		= AT91_PIN_PB15,
+		.active_low	= 1,
+		.desc		= "Joystick Right",
+	},
+	{
+		.code		= KEY_UP,
+		.gpio		= AT91_PIN_PB16,
+		.active_low	= 1,
+		.desc		= "Joystick Up",
+	},
+	{
+		.code		= KEY_DOWN,
+		.gpio		= AT91_PIN_PB17,
+		.active_low	= 1,
+		.desc		= "Joystick Down",
+	},
+	{
+		.code		= KEY_ENTER,
+		.gpio		= AT91_PIN_PB18,
+		.active_low	= 1,
+		.desc		= "Joystick Press",
+	},
+};
+
+static struct gpio_keys_platform_data ek_button_data = {
+	.buttons	= ek_buttons,
+	.nbuttons	= ARRAY_SIZE(ek_buttons),
+};
+
+static struct platform_device ek_button_device = {
+	.name		= "gpio-keys",
+	.id		= -1,
+	.num_resources	= 0,
+	.dev		= {
+		.platform_data	= &ek_button_data,
+	}
+};
+
+static void __init ek_add_device_buttons(void)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(ek_buttons); i++) {
+		at91_set_GPIO_periph(ek_buttons[i].gpio, 1);
+		at91_set_deglitch(ek_buttons[i].gpio, 1);
+	}
+
+	platform_device_register(&ek_button_device);
+}
+#else
+static void __init ek_add_device_buttons(void) {}
+#endif
+
+
+/*
+ * LEDs ... these could all be PWM-driven, for variable brightness
+ */
+static struct gpio_led ek_leds[] = {
+	{	/* "top" led, red, powerled */
+		.name			= "d8",
+		.gpio			= AT91_PIN_PD30,
+		.default_trigger	= "heartbeat",
+	},
+	{	/* "left" led, green, userled2, pwm3 */
+		.name			= "d6",
+		.gpio			= AT91_PIN_PD0,
+		.active_low		= 1,
+		.default_trigger	= "nand-disk",
+	},
+#if !(defined(CONFIG_LEDS_ATMEL_PWM) || defined(CONFIG_LEDS_ATMEL_PWM_MODULE))
+	{	/* "right" led, green, userled1, pwm1 */
+		.name			= "d7",
+		.gpio			= AT91_PIN_PD31,
+		.active_low		= 1,
+		.default_trigger	= "mmc0",
+	},
+#endif
+};
+
+
+/*
+ * PWM Leds
+ */
+static struct gpio_led ek_pwm_led[] = {
+#if defined(CONFIG_LEDS_ATMEL_PWM) || defined(CONFIG_LEDS_ATMEL_PWM_MODULE)
+	{	/* "right" led, green, userled1, pwm1 */
+		.name			= "d7",
+		.gpio			= 1,	/* is PWM channel number */
+		.active_low		= 1,
+		.default_trigger	= "none",
+	},
+#endif
+};
+
+
+
+static void __init ek_board_init(void)
+{
+	/* Serial */
+	at91_add_device_serial();
+	/* USB HS Host */
+	at91_add_device_usbh_ohci(&ek_usbh_hs_data);
+	/* USB HS Device */
+	at91_add_device_usba(&ek_usba_udc_data);
+	/* SPI */
+	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
+	/* Ethernet */
+	at91_add_device_eth(&ek_macb_data);
+	/* NAND */
+	ek_add_device_nand();
+	/* I2C */
+	at91_add_device_i2c(0, NULL, 0);
+	/* LCD Controller */
+	at91_add_device_lcdc(&ek_lcdc_data);
+	/* Push Buttons */
+	ek_add_device_buttons();
+	/* LEDs */
+	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
+	at91_pwm_leds(ek_pwm_led, ARRAY_SIZE(ek_pwm_led));
+}
+
+MACHINE_START(AT91SAM9G45EKES, "Atmel AT91SAM9G45-EKES")
+	/* Maintainer: Atmel */
+	.phys_io	= AT91_BASE_SYS,
+	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,
+	.boot_params	= AT91_SDRAM_BASE + 0x100,
+	.timer		= &at91sam926x_timer,
+	.map_io		= ek_map_io,
+	.init_irq	= ek_init_irq,
+	.init_machine	= ek_board_init,
+MACHINE_END
diff --git a/arch/arm/mach-at91/generic.h b/arch/arm/mach-at91/generic.h
index b5daf7f..88e413b 100644
--- a/arch/arm/mach-at91/generic.h
+++ b/arch/arm/mach-at91/generic.h
@@ -14,6 +14,7 @@ extern void __init at91sam9260_initialize(unsigned long main_clock);
 extern void __init at91sam9261_initialize(unsigned long main_clock);
 extern void __init at91sam9263_initialize(unsigned long main_clock);
 extern void __init at91sam9rl_initialize(unsigned long main_clock);
+extern void __init at91sam9g45_initialize(unsigned long main_clock);
 extern void __init at91x40_initialize(unsigned long main_clock);
 extern void __init at91cap9_initialize(unsigned long main_clock);
 
@@ -23,6 +24,7 @@ extern void __init at91sam9260_init_interrupts(unsigned int priority[]);
 extern void __init at91sam9261_init_interrupts(unsigned int priority[]);
 extern void __init at91sam9263_init_interrupts(unsigned int priority[]);
 extern void __init at91sam9rl_init_interrupts(unsigned int priority[]);
+extern void __init at91sam9g45_init_interrupts(unsigned int priority[]);
 extern void __init at91x40_init_interrupts(unsigned int priority[]);
 extern void __init at91cap9_init_interrupts(unsigned int priority[]);
 extern void __init at91_aic_init(unsigned int priority[]);
diff --git a/arch/arm/mach-at91/include/mach/board.h b/arch/arm/mach-at91/include/mach/board.h
index e6afff8..74801d2 100644
--- a/arch/arm/mach-at91/include/mach/board.h
+++ b/arch/arm/mach-at91/include/mach/board.h
@@ -80,7 +80,8 @@ struct at91_eth_data {
 };
 extern void __init at91_add_device_eth(struct at91_eth_data *data);
 
-#if defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9263) || defined(CONFIG_ARCH_AT91SAM9G20) || defined(CONFIG_ARCH_AT91CAP9)
+#if defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9263) || defined(CONFIG_ARCH_AT91SAM9G20) || defined(CONFIG_ARCH_AT91CAP9) \
+	|| defined(CONFIG_ARCH_AT91SAM9G45)
 #define eth_platform_data	at91_eth_data
 #endif
 
@@ -90,6 +91,7 @@ struct at91_usbh_data {
 	u8		vbus_pin[2];	/* port power-control pin */
 };
 extern void __init at91_add_device_usbh(struct at91_usbh_data *data);
+extern void __init at91_add_device_usbh_ohci(struct at91_usbh_data *data);
 
  /* NAND / SmartMedia */
 struct atmel_nand_data {
@@ -105,7 +107,11 @@ struct atmel_nand_data {
 extern void __init at91_add_device_nand(struct atmel_nand_data *data);
 
  /* I2C*/
+#if defined(CONFIG_ARCH_AT91SAM9G45)
+extern void __init at91_add_device_i2c(short i2c_id, struct i2c_board_info *devices, int nr_devices);
+#else
 extern void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices);
+#endif
 
  /* SPI */
 extern void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices);
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 214a92d..af8a1d7 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -219,7 +219,7 @@ config MII
 
 config MACB
 	tristate "Atmel MACB support"
-	depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91SAM9G20 || ARCH_AT91CAP9
+	depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91SAM9G20 || ARCH_AT91SAM9G45 || ARCH_AT91CAP9
 	select PHYLIB
 	help
 	  The Atmel MACB ethernet interface is found on many AT32 and AT91
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index 0048f11..5152168 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -933,7 +933,7 @@ config FB_S1D13XXX
 
 config FB_ATMEL
 	tristate "AT91/AT32 LCD Controller support"
-	depends on FB && (ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91CAP9 || AVR32)
+	depends on FB && (ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91SAM9G45 || ARCH_AT91CAP9 || AVR32)
 	select FB_CFB_FILLRECT
 	select FB_CFB_COPYAREA
 	select FB_CFB_IMAGEBLIT
-- 
1.5.3.7