From: Denis Turischev <denis@compulab.co.il>
To: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-kernel@vger.kernel.org
Subject: SBC-FITPC2 watchdog support
Date: Thu, 16 Jul 2009 15:29:06 +0300 [thread overview]
Message-ID: <4A5F1D12.2080907@compulab.co.il> (raw)
Adds support to watchdog timer on SBC-FITPC2 board by Compulab.
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
diff -Nru linux-2.6.31-rc3.orig/drivers/watchdog/Kconfig
linux-2.6.31-rc3/drivers/watchdog/Kconfig
--- linux-2.6.31-rc3.orig/drivers/watchdog/Kconfig 2009-07-14
04:18:52.000000000 +0300
+++ linux-2.6.31-rc3/drivers/watchdog/Kconfig 2009-07-16
13:52:08.000000000 +0300
@@ -721,6 +721,28 @@
To compile this driver as a module, choose M here: the
module will be called sbc_epx_c3.
+config SBC_FITPC2_WATCHDOG
+ tristate "Compulab SBC-FITPC2 watchdog"
+ depends on X86
+ ---help---
+ This is the driver for the built-in watchdog timer on the fit-PC2
+ Single-board computer made by Compulab.
+
+ It`s possible to enable watchdog timer either from BIOS (F2)
or from booted Linux.
+ When "Watchdog Timer Value" enabled one can set 31-255 s
operational range.
+
+ Entering BIOS setup temporary disables watchdog operation
regardless to current state,
+ so system will not be restarted while user in BIOS setup.
+
+ Once watchdog was enabled the system will be restarted every
+ "Watchdog Timer Value" period, so to prevent it user can
restart or
+ disable the watchdog.
+
+ To compile this driver as a module, choose M here: the
+ module will be called sbc_fitpc2_wdt.
+
+ Most people will say N.
+
# M32R Architecture
# M68K Architecture
diff -Nru linux-2.6.31-rc3.orig/drivers/watchdog/Makefile
linux-2.6.31-rc3/drivers/watchdog/Makefile
--- linux-2.6.31-rc3.orig/drivers/watchdog/Makefile 2009-07-14
04:18:52.000000000 +0300
+++ linux-2.6.31-rc3/drivers/watchdog/Makefile 2009-07-16
13:47:44.000000000 +0300
@@ -93,6 +93,7 @@
obj-$(CONFIG_W83977F_WDT) += w83977f_wdt.o
obj-$(CONFIG_MACHZ_WDT) += machzwd.o
obj-$(CONFIG_SBC_EPX_C3_WATCHDOG) += sbc_epx_c3.o
+obj-$(CONFIG_SBC_FITPC2_WATCHDOG) += sbc_fitpc2_wdt.o
# M32R Architecture
diff -Nru linux-2.6.31-rc3.orig/drivers/watchdog/sbc_fitpc2_wdt.c
linux-2.6.31-rc3/drivers/watchdog/sbc_fitpc2_wdt.c
--- linux-2.6.31-rc3.orig/drivers/watchdog/sbc_fitpc2_wdt.c
1970-01-01 02:00:00.000000000 +0200
+++ linux-2.6.31-rc3/drivers/watchdog/sbc_fitpc2_wdt.c 2009-07-16
14:03:35.000000000 +0300
@@ -0,0 +1,219 @@
+/*
+ * Watchdog driver for SBC-FITPC2 board
+ *
+ * Author: Denis Turischev <denis@compulab.co.il>
+ *
+ * Adapted from the IXP2000 watchdog driver by Deepak Saxena.
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/miscdevice.h>
+#include <linux/watchdog.h>
+#include <linux/ioport.h>
+#include <linux/delay.h>
+#include <linux/notifier.h>
+#include <linux/fs.h>
+#include <linux/reboot.h>
+#include <linux/init.h>
+#include <linux/moduleparam.h>
+
+#include <linux/io.h>
+#include <linux/uaccess.h>
+#include <asm/system.h>
+
+static int nowayout = WATCHDOG_NOWAYOUT;
+static unsigned int margin = 60; /* (secs) Default is 1 minute */
+static unsigned long wdt_status;
+static spinlock_t wdt_lock;
+
+#define WDT_IN_USE 0
+#define WDT_OK_TO_CLOSE 1
+
+#define COMMAND_PORT 0x4c
+#define DATA_PORT 0x48
+
+#define IFACE_ON_COMMAND 1
+#define REBOOT_COMMAND 2
+
+static void wdt_send_data(unsigned char command, unsigned char data)
+{
+ outb(command, COMMAND_PORT);
+ mdelay(100);
+ outb(data, DATA_PORT);
+ mdelay(200);
+}
+
+static void wdt_enable(void)
+{
+ spin_lock(&wdt_lock);
+ wdt_send_data(IFACE_ON_COMMAND, 1);
+ wdt_send_data(REBOOT_COMMAND, margin);
+ spin_unlock(&wdt_lock);
+}
+
+static void wdt_disable(void)
+{
+ spin_lock(&wdt_lock);
+ wdt_send_data(IFACE_ON_COMMAND, 0);
+ wdt_send_data(REBOOT_COMMAND, 0);
+ spin_unlock(&wdt_lock);
+}
+
+static int fitpc2_wdt_open(struct inode *inode, struct file *file)
+{
+ if (test_and_set_bit(WDT_IN_USE, &wdt_status))
+ return -EBUSY;
+
+ clear_bit(WDT_OK_TO_CLOSE, &wdt_status);
+
+ wdt_enable();
+
+ return nonseekable_open(inode, file);
+}
+
+static ssize_t
+fitpc2_wdt_write(struct file *file, const char *data, size_t len,
loff_t *ppos)
+{
+ if (len) {
+ if (!nowayout) {
+ size_t i;
+
+ clear_bit(WDT_OK_TO_CLOSE, &wdt_status);
+
+ for (i = 0; i != len; i++) {
+ char c;
+
+ if (get_user(c, data + i))
+ return -EFAULT;
+
+ if (c == 'V')
+ set_bit(WDT_OK_TO_CLOSE,
&wdt_status);
+ }
+ }
+ wdt_enable();
+ }
+
+ return len;
+}
+
+
+static struct watchdog_info ident = {
+ .options = WDIOF_MAGICCLOSE | WDIOF_SETTIMEOUT |
+ WDIOF_KEEPALIVEPING,
+ .identity = "SBC-FITPC2 Watchdog",
+};
+
+
+static long
+fitpc2_wdt_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
+{
+ int ret = -ENOTTY;
+ int time;
+
+ switch (cmd) {
+ case WDIOC_GETSUPPORT:
+ ret = copy_to_user((struct watchdog_info *)arg, &ident,
+ sizeof(ident)) ? -EFAULT : 0;
+ break;
+
+ case WDIOC_GETSTATUS:
+ ret = put_user(0, (int *)arg);
+ break;
+
+ case WDIOC_GETBOOTSTATUS:
+ ret = put_user(0, (int *)arg);
+ break;
+
+ case WDIOC_KEEPALIVE:
+ wdt_enable();
+ ret = 0;
+ break;
+
+ case WDIOC_SETTIMEOUT:
+ ret = get_user(time, (int *)arg);
+ if (ret)
+ break;
+
+ if (time < 31 || time > 255) {
+ ret = -EINVAL;
+ break;
+ }
+
+ margin = time;
+ wdt_enable();
+ /* Fall through */
+
+ case WDIOC_GETTIMEOUT:
+ ret = put_user(margin, (int *)arg);
+ break;
+ }
+
+ return ret;
+}
+
+static int fitpc2_wdt_release(struct inode *inode, struct file *file)
+{
+ if (test_bit(WDT_OK_TO_CLOSE, &wdt_status)) {
+ wdt_disable();
+ } else {
+ printk(KERN_CRIT "WATCHDOG: Device closed unexpectedly - "
+ "timer will not stop\n");
+ }
+
+ clear_bit(WDT_IN_USE, &wdt_status);
+ clear_bit(WDT_OK_TO_CLOSE, &wdt_status);
+
+ return 0;
+}
+
+
+static const struct file_operations fitpc2_wdt_fops = {
+ .owner = THIS_MODULE,
+ .llseek = no_llseek,
+ .write = fitpc2_wdt_write,
+ .unlocked_ioctl = fitpc2_wdt_ioctl,
+ .open = fitpc2_wdt_open,
+ .release = fitpc2_wdt_release,
+};
+
+static struct miscdevice fitpc2_wdt_miscdev = {
+ .minor = WATCHDOG_MINOR,
+ .name = "watchdog",
+ .fops = &fitpc2_wdt_fops,
+};
+
+static int __init fitpc2_wdt_init(void)
+{
+ if (margin < 31 || margin > 255) {
+ printk(KERN_CRIT "WATCHDOG: margin must be in range 31 -
255"
+ " seconds, you tried to set %d\n", margin);
+ return -EINVAL;
+ }
+ return misc_register(&fitpc2_wdt_miscdev);
+}
+
+static void __exit fitpc2_wdt_exit(void)
+{
+ misc_deregister(&fitpc2_wdt_miscdev);
+}
+
+module_init(fitpc2_wdt_init);
+module_exit(fitpc2_wdt_exit);
+
+MODULE_AUTHOR("Denis Turischev <denis@compulab.co.il>");
+MODULE_DESCRIPTION("SBC-FITPC2 Watchdog");
+
+module_param(margin, int, 0);
+MODULE_PARM_DESC(margin, "Watchdog margin in seconds (default 60s)");
+
+module_param(nowayout, int, 0);
+MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started");
+
+MODULE_LICENSE("GPL");
+MODULE_ALIAS_MISCDEV(WATCHDOG_MINOR);
+
next reply other threads:[~2009-07-16 12:29 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-07-16 12:29 Denis Turischev [this message]
2009-07-17 8:43 ` SBC-FITPC2 watchdog support Andrey Panin
2009-07-22 17:50 ` Wim Van Sebroeck
2009-07-23 18:16 ` Mike Rapoport
-- strict thread matches above, loose matches on Subject: below --
2009-07-15 15:27 Denis Turischev
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4A5F1D12.2080907@compulab.co.il \
--to=denis@compulab.co.il \
--cc=linux-kernel@vger.kernel.org \
--cc=wim@iguana.be \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox