From: Yinghai Lu <yinghai@kernel.org>
To: Jens Axboe <jens.axboe@oracle.com>
Cc: Ingo Molnar <mingo@elte.hu>, Thomas Gleixner <tglx@linutronix.de>,
"H. Peter Anvin" <hpa@zytor.com>,
"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>
Subject: Re: Bisected regression (Was Re: current -git fails to boot on nehalem-ex)
Date: Thu, 10 Dec 2009 10:34:07 -0800 [thread overview]
Message-ID: <4B213F1F.2020305@kernel.org> (raw)
In-Reply-To: <20091210180727.GK8742@kernel.dk>
Jens Axboe wrote:
> On Thu, Dec 10 2009, Yinghai wrote:
>>
>>
>>
>> On Dec 10, 2009, at 8:06 AM, Ingo Molnar <mingo@elte.hu> wrote:
>>
>>> * Jens Axboe <jens.axboe@oracle.com> wrote:
>>>
>>>> On Thu, Dec 10 2009, Jens Axboe wrote:
>>>>> Hi,
>>>>>
>>>>> As written in the subject, it just hard hangs before writing
>>>>> anything on
>>>>> the console. With earlyprintk, I captured the failure, see below.
>>>>>
>>>>> I'll try and bisect this, but it takes some time (since the bios and
>>>>> post process takes forever). I just updated the firmware on the
>>>>> box as
>>>>> well, but it did boot 2.6.32 (and RHEL5 boots fine too). Of course
>>>>> that
>>>>> doesn't rule out a BIOS bug.
>>>> Results are persistent, git bisect points to:
>>>>
>>>> commit b24c2a925a9837cccf54d50aeac22ba0cbc15455
>>>> Author: Yinghai Lu <yinghai@kernel.org>
>>>> Date: Tue Nov 24 02:48:18 2009 -0800
>>>>
>>>> x86: Move find_smp_config() earlier and avoid bootmem usage
>>>>
>>>> which appears consistent with the panic(). Reverting that does indeed
>>>> make current -git boot properly.
>>> Thanks. Yinghai, do you have any ideas, or should we revert it?
>>>
>> Let find the root cause
>>
>> Jen
>
> Jens :-)
>
>> Can you boot with earlyconsole or earlyprintk and debug?
>
> The original report already included oops output from earlyprintk, it's
> below as well.
>
> kernel /vmlinuz-2.6 root=/dev/sda3 ro console=ttyS0,115200 console=tty0 earlyp
> rintk=serial,ttyS0,115200
> [Linux-bzImage, setup=0x3200, size=0x298f90]
>
>
> [ 0.000000] Linux version 2.6.32 (axboe@nehalem) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) #35 SMP Thu Dec 10 09:47:51 CET 2009 *
> [ 0.000000] Command line: root=/dev/sda3 ro console=ttyS0,115200 console=tty0 earlyprintk=serial,ttyS0,115200 *
> [ 0.000000] BIOS-provided physical RAM map: *
> [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009a400 (usable) *
> [ 0.000000] BIOS-e820: 000000000009a400 - 00000000000a0000 (reserved) *
> [ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)***
> [ 0.000000] BIOS-e820: 0000000000100000 - 0000000078c75000 (usable)
> [ 0.000000] BIOS-e820: 0000000078c75000 - 0000000078e89000 (ACPI NVS)
> [ 0.000000] BIOS-e820: 0000000078e89000 - 000000007924e000 (ACPI data)
> [ 0.000000] BIOS-e820: 000000007924e000 - 00000000792c2000 (reserved)
> [ 0.000000] BIOS-e820: 00000000792c2000 - 00000000792d2000 (ACPI data)
> [ 0.000000] BIOS-e820: 00000000792d2000 - 00000000792e7000 (reserved)
> [ 0.000000] BIOS-e820: 00000000792e7000 - 0000000079301000 (ACPI data)
> [ 0.000000] BIOS-e820: 0000000079301000 - 0000000079303000 (reserved)
> [ 0.000000] BIOS-e820: 0000000079303000 - 0000000079305000 (ACPI data)
> [ 0.000000] BIOS-e820: 0000000079305000 - 0000000079310000 (reserved)
> [ 0.000000] BIOS-e820: 0000000079310000 - 0000000079314000 (ACPI data)
> [ 0.000000] BIOS-e820: 0000000079314000 - 0000000079319000 (reserved)
> [ 0.000000] BIOS-e820: 0000000079319000 - 0000000079336000 (ACPI data)
> [ 0.000000] BIOS-e820: 0000000079336000 - 0000000079358000 (reserved)
> [ 0.000000] BIOS-e820: 0000000079358000 - 0000000079388000 (ACPI data)
> [ 0.000000] BIOS-e820: 0000000079388000 - 00000000793c9000 (reserved)
> [ 0.000000] BIOS-e820: 00000000793c9000 - 000000007968f000 (ACPI data)
> [ 0.000000] BIOS-e820: 000000007968f000 - 00000000796bb000 (reserved)
> [ 0.000000] BIOS-e820: 00000000796bb000 - 00000000799d8000 (ACPI data)
> [ 0.000000] BIOS-e820: 00000000799d8000 - 0000000079bd8000 (ACPI NVS)
> [ 0.000000] BIOS-e820: 0000000079bd8000 - 0000000079dc7000 (ACPI data)
> [ 0.000000] BIOS-e820: 0000000079dc7000 - 0000000079dcb000 (reserved)
> [ 0.000000] BIOS-e820: 0000000079dcb000 - 0000000079e1c000 (ACPI data)
> [ 0.000000] BIOS-e820: 0000000079e1c000 - 0000000079e87000 (reserved)
> [ 0.000000] BIOS-e820: 0000000079e87000 - 000000007bd5f000 (ACPI data)
> [ 0.000000] BIOS-e820: 000000007bd5f000 - 000000007be4f000 (reserved)
> [ 0.000000] BIOS-e820: 000000007be4f000 - 000000007bf87000 (ACPI data)
> [ 0.000000] BIOS-e820: 000000007bf87000 - 000000007bfcf000 (ACPI NVS)
> [ 0.000000] BIOS-e820: 000000007bfcf000 - 000000007bfff000 (ACPI data)
> [ 0.000000] BIOS-e820: 000000007bfff000 - 0000000090000000 (reserved)
> [ 0.000000] BIOS-e820: 00000000fc000000 - 00000000fd000000 (reserved)
> [ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved)
> [ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
> [ 0.000000] BIOS-e820: 0000000100000000 - 0000001080000000 (usable)
> [ 0.000000] bootconsole [earlyser0] enabled
> [ 0.000000] NX (Execute Disable) protection: active
> [ 0.000000] DMI 2.5 present.
> [ 0.000000] last_pfn = 0x1080000 max_arch_pfn = 0x400000000
> [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
> [ 0.000000] last_pfn = 0x78c75 max_arch_pfn = 0x400000000
> [ 0.000000] init_memory_mapping: 0000000000000000-0000000078c75000
> [ 0.000000] init_memory_mapping: 0000000100000000-0000001080000000
> [ 0.000000] ACPI: RSDP 00000000000f0410 00024 (v02 QUANTA)
> [ 0.000000] ACPI: XSDT 000000007bffe120 000BC (v01 QUANTA QSSC-S4R 00000000 01000013)
> [ 0.000000] ACPI: FACP 000000007bffd000 000F4 (v04 QUANTA QSSC-S4R 00000000 MSFT 0100000D)
> [ 0.000000] ACPI: DSDT 000000007bfe3000 19BAD (v02 QUANTA QSSC-S4R 00000003 MSFT 0100000D)
> [ 0.000000] ACPI: FACS 000000007bf87000 00040
> [ 0.000000] ACPI: APIC 000000007bfe2000 003E4 (v02 QUANTA QSSC-S4R 00000000 MSFT 0100000D)
> [ 0.000000] ACPI: MSCT 000000007bfe1000 00090 (v01 QUANTA QSSC-S4R 00000001 MSFT 0100000D)
> [ 0.000000] ACPI: MCFG 000000007bfe0000 0003C (v01 QUANTA QSSC-S4R 00000001 MSFT 0100000D)
> [ 0.000000] ACPI: HPET 000000007bfdf000 00038 (v01 QUANTA QSSC-S4R 00000001 MSFT 0100000D)
> [ 0.000000] ACPI: SLIT 000000007bfde000 0003C (v01 QUANTA QSSC-S4R 00000001 MSFT 0100000D)
> [ 0.000000] ACPI: SRAT 000000007bfdd000 00930 (v02 QUANTA QSSC-S4R 00000001 MSFT 0100000D)
> [ 0.000000] ACPI: SPCR 000000007bfdc000 00050 (v01 QUANTA QSSC-S4R 00000000 MSFT 0100000D)
> [ 0.000000] ACPI: WDDT 000000007bfdb000 00040 (v01 QUANTA QSSC-S4R 00000000 MSFT 0100000D)
> [ 0.000000] ACPI: SSDT 000000007bf4a000 3CFA4 (v02 QUANTA QSSC-S4R 00004000 INTL 20061109)
> [ 0.000000] ACPI: SSDT 000000007bfda000 00174 (v02 QUANTA QSSC-S4R 00004000 INTL 20061109)
> [ 0.000000] ACPI: PMCT 000000007bfd9000 00064 (v01 QUANTA QSSC-S4R 00000000 MSFT 0100000D)
> [ 0.000000] ACPI: MIGT 000000007bfd8000 00040 (v01 QUANTA QSSC-S4R 00000000 MSFT 0100000D)
> [ 0.000000] ACPI: TCPA 000000007bfd5000 00032 (v00 QUANTA QSSC-S4R 00000000 00000000)
> [ 0.000000] ACPI: HEST 000000007bfd4000 005D0 (v01 QUANTA QSSC-S4R 00000001 INTL 00000001)
> [ 0.000000] ACPI: BERT 000000007bfd3000 00030 (v01 QUANTA QSSC-S4R 00000001 INTL 00000001)
> [ 0.000000] ACPI: ERST 000000007bfd2000 00230 (v01 QUANTA QSSC-S4R 00000001 INTL 00000001)
> [ 0.000000] ACPI: EINJ 000000007bfd1000 00130 (v01 QUANTA QSSC-S4R 00000001 INTL 00000001)
> [ 0.000000] ACPI: DMAR 000000007bfd0000 00350 (v01 QUANTA QSSC-S4R 00000001 MSFT 0100000D)
> [ 0.000000] found SMP MP-table at [ffff8800000fdd80] fdd80
> [ 0.000000] Kernel panic - not syncing: Overlapping early reservations 12-f011 MP-table mpc to 0-fff BIOS data page
mptable mpc is [12 - f011]
what a BIOS !
can you check if it works with 2.6.32 + "acpi=off"?
Thanks
YH
next prev parent reply other threads:[~2009-12-10 18:35 UTC|newest]
Thread overview: 31+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-12-10 9:10 current -git fails to boot on nehalem-ex Jens Axboe
2009-12-10 10:39 ` Bisected regression (Was Re: current -git fails to boot on nehalem-ex) Jens Axboe
2009-12-10 16:06 ` Ingo Molnar
2009-12-10 17:26 ` Yinghai
2009-12-10 18:07 ` Jens Axboe
2009-12-10 18:34 ` Yinghai Lu [this message]
2009-12-10 18:41 ` Bisected regression Roland Dreier
2009-12-10 18:44 ` Jens Axboe
2009-12-10 19:13 ` Yinghai Lu
2009-12-10 18:44 ` Yinghai Lu
2009-12-10 18:42 ` Bisected regression (Was Re: current -git fails to boot on nehalem-ex) Yinghai Lu
2009-12-10 18:45 ` Jens Axboe
2009-12-10 19:07 ` Jens Axboe
2009-12-10 19:19 ` Yinghai Lu
2009-12-10 19:26 ` Jens Axboe
2009-12-10 19:34 ` Bisected regression Roland Dreier
2009-12-10 21:07 ` Bisected regression (Was Re: current -git fails to boot on nehalem-ex) Yinghai Lu
2009-12-10 21:15 ` Jens Axboe
2009-12-10 22:39 ` H. Peter Anvin
2009-12-10 22:45 ` Yinghai Lu
2009-12-10 22:54 ` H. Peter Anvin
2009-12-10 22:47 ` Bisected regression Roland Dreier
2009-12-10 22:50 ` H. Peter Anvin
2009-12-11 8:19 ` Bisected regression (Was Re: current -git fails to boot on nehalem-ex) Jens Axboe
2009-12-11 8:32 ` Ingo Molnar
2009-12-11 8:55 ` [tip:x86/urgent] x86: Use find_e820() instead of hard coded trampoline address tip-bot for Yinghai Lu
2009-12-10 19:28 ` Bisected regression Roland Dreier
2009-12-10 19:33 ` Yinghai Lu
2009-12-10 19:36 ` Roland Dreier
2009-12-10 19:50 ` Yinghai Lu
2009-12-10 22:44 ` H. Peter Anvin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4B213F1F.2020305@kernel.org \
--to=yinghai@kernel.org \
--cc=hpa@zytor.com \
--cc=jens.axboe@oracle.com \
--cc=linux-kernel@vger.kernel.org \
--cc=mingo@elte.hu \
--cc=tglx@linutronix.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox