From: Michal Simek <monstr@monstr.eu>
To: Christoph Hellwig <hch@lst.de>
Cc: roland@redhat.com, oleg@redhat.com, akpm@linux-foundation.org,
linux-kernel@vger.kernel.org, linux-arch@vger.kernel.org
Subject: Re: [PATCH 8/14] microblaze: use generic ptrace_resume code
Date: Wed, 03 Feb 2010 12:00:22 +0100 [thread overview]
Message-ID: <4B695746.10309@monstr.eu> (raw)
In-Reply-To: <20100202185946.GH3630@lst.de>
Acked-by: Michal Simek <monstr@monstr.eu>
Christoph Hellwig wrote:
> Use the generic ptrace_resume code for PTRACE_SYSCALL, PTRACE_CONT and
> PTRACE_KILL. This also makes PTRACE_SINGLESTEP return -EIO while it
> previously succeeded despite not actually causing any kind of single
> stepping.
>
> Also the TIF_SYSCALL_TRACE thread flag is now cleared on PTRACE_KILL
> which it previously wasn't which is consistent with all architectures
> using the modern ptrace code.
>
> Signed-off-by: Christoph Hellwig <hch@lst.de>
>
> Index: linux-2.6/arch/microblaze/kernel/ptrace.c
> ===================================================================
> --- linux-2.6.orig/arch/microblaze/kernel/ptrace.c 2010-02-02 11:23:56.002003861 +0100
> +++ linux-2.6/arch/microblaze/kernel/ptrace.c 2010-02-02 19:20:16.997254566 +0100
> @@ -110,43 +110,6 @@ long arch_ptrace(struct task_struct *chi
> if (rval == 0 && request == PTRACE_PEEKUSR)
> rval = put_user(val, (unsigned long *)data);
> break;
> - /* Continue and stop at next (return from) syscall */
> - case PTRACE_SYSCALL:
> - pr_debug("PTRACE_SYSCALL\n");
> - case PTRACE_SINGLESTEP:
> - pr_debug("PTRACE_SINGLESTEP\n");
> - /* Restart after a signal. */
> - case PTRACE_CONT:
> - pr_debug("PTRACE_CONT\n");
> - rval = -EIO;
> - if (!valid_signal(data))
> - break;
> -
> - if (request == PTRACE_SYSCALL)
> - set_tsk_thread_flag(child, TIF_SYSCALL_TRACE);
> - else
> - clear_tsk_thread_flag(child, TIF_SYSCALL_TRACE);
> -
> - child->exit_code = data;
> - pr_debug("wakeup_process\n");
> - wake_up_process(child);
> - rval = 0;
> - break;
> -
> - /*
> - * make the child exit. Best I can do is send it a sigkill.
> - * perhaps it should be put in the status that it wants to
> - * exit.
> - */
> - case PTRACE_KILL:
> - pr_debug("PTRACE_KILL\n");
> - rval = 0;
> - if (child->exit_state == EXIT_ZOMBIE) /* already dead */
> - break;
> - child->exit_code = SIGKILL;
> - wake_up_process(child);
> - break;
> -
> default:
> rval = ptrace_request(child, request, addr, data);
> }
--
Michal Simek, Ing. (M.Eng)
w: www.monstr.eu p: +42-0-721842854
Maintainer of Linux kernel 2.6 Microblaze Linux - http://www.monstr.eu/fdt/
Microblaze U-BOOT custodian
next prev parent reply other threads:[~2010-02-03 11:02 UTC|newest]
Thread overview: 42+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-02-02 18:57 [PATCH 1/14] move user_enable_single_step & co prototypes to linux/ptrace.h Christoph Hellwig
2010-02-02 18:58 ` [PATCH 2/14] alpha: use generic ptrace_resume code Christoph Hellwig
2010-02-03 4:35 ` Matt Turner
2010-02-02 18:58 ` [PATCH 3/14] arm: " Christoph Hellwig
2010-02-02 18:58 ` [PATCH 4/14] avr32: " Christoph Hellwig
2010-02-03 3:17 ` Haavard Skinnemoen
2010-02-03 8:36 ` Christoph Hellwig
2010-02-03 19:22 ` Oleg Nesterov
2010-02-03 19:28 ` Christoph Hellwig
2010-02-02 18:59 ` [PATCH 5/14] blackfin: " Christoph Hellwig
2010-02-02 20:29 ` Mike Frysinger
2010-02-03 19:36 ` Mike Frysinger
2010-02-03 19:42 ` Christoph Hellwig
2010-02-11 9:43 ` [PATCH 0/2] Blackfin: " Mike Frysinger
2010-02-11 9:43 ` [PATCH 1/2] Blackfin: initial tracehook support Mike Frysinger
2010-02-11 20:46 ` Roland McGrath
2010-02-11 23:54 ` Mike Frysinger
2010-02-12 3:24 ` Roland McGrath
2010-02-12 4:33 ` Mike Frysinger
2010-02-12 15:24 ` Oleg Nesterov
2010-02-12 20:44 ` Roland McGrath
2010-02-13 9:41 ` Mike Frysinger
2010-02-15 7:36 ` Mike Frysinger
2010-02-15 20:07 ` Roland McGrath
2010-02-11 9:43 ` [PATCH 2/2] Blackfin: use generic ptrace_resume code Mike Frysinger
2010-02-02 18:59 ` [PATCH 6/14] h8300: " Christoph Hellwig
2010-02-02 18:59 ` [PATCH 7/14] m68knommu: " Christoph Hellwig
2010-02-03 6:54 ` Greg Ungerer
2010-02-02 18:59 ` [PATCH 8/14] microblaze: " Christoph Hellwig
2010-02-03 11:00 ` Michal Simek [this message]
2010-02-02 18:59 ` [PATCH 9/14] mips: " Christoph Hellwig
2010-02-02 19:19 ` Ralf Baechle
2010-02-02 19:00 ` [PATCH 10/14] um: " Christoph Hellwig
2010-02-02 19:00 ` [PATCH 11/14] xtensa: " Christoph Hellwig
2010-02-02 19:00 ` [PATCH 12/14] cris arch-v10: " Christoph Hellwig
2010-02-02 19:00 ` [PATCH, RFC 13/14] cris arch-v32: " Christoph Hellwig
2010-02-02 19:00 ` [PATCH, RFC 14/14] m32r: " Christoph Hellwig
2010-02-03 8:42 ` [PATCH 1/14] move user_enable_single_step & co prototypes to linux/ptrace.h Mike Frysinger
2010-02-03 8:56 ` Christoph Hellwig
2010-02-08 10:50 ` David Howells
2010-02-08 19:51 ` Roland McGrath
2010-02-10 22:03 ` Christoph Hellwig
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4B695746.10309@monstr.eu \
--to=monstr@monstr.eu \
--cc=akpm@linux-foundation.org \
--cc=hch@lst.de \
--cc=linux-arch@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=oleg@redhat.com \
--cc=roland@redhat.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).