* Re: ERROR: Unable to locate IOAPIC for GSI xx
[not found] <AANLkTilT0cPU8y2m4ZeatfvtflAagSyQEP9JubqZ6TeW@mail.gmail.com>
@ 2010-06-03 9:08 ` Eric W. Biederman
0 siblings, 0 replies; 2+ messages in thread
From: Eric W. Biederman @ 2010-06-03 9:08 UTC (permalink / raw)
To: Avinash Kurup; +Cc: H. Peter Anvin, linux-kernel
Avinash Kurup <kurup.avinash@gmail.com> writes:
> Hi Eric,
> I get the following errors while booting into 2.6.35-rc1. I did not
> get these in 2.6.34 . The computer however boots and works fine, So its not
> serious but the following errors are displayed in dmesg.
>
> [ 0.089969] ERROR: Unable to locate IOAPIC for GSI 13
> [ 0.090556] ERROR: Unable to locate IOAPIC for GSI 8
> [ 0.091104] ERROR: Unable to locate IOAPIC for GSI 12
> [ 0.091375] ERROR: Unable to locate IOAPIC for GSI 1
> [ 0.093195] ERROR: Unable to locate IOAPIC for GSI 4
> [ 0.094342] ERROR: Unable to locate IOAPIC for GSI 10
> [ 0.096335] ERROR: Unable to locate IOAPIC for GSI 6
>
> I bisected the problem to this commit.
Can I get a full boot log?
It sounds like this would easily be triggered by one of my patches, I
am dubious about the particular patch you point out. As that only
adds a new function but does not call it.
There should be boot lines that say something like:
> [ 0.000000] ACPI: Local APIC address 0xfee00000
> [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
> [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
> [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
> [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
> [ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
> [ 0.000000] IOAPIC[0]: apic_id 4, version 0, address 0xfec00000, GSI 0-23
> [ 0.000000] ACPI: IOAPIC (id[0x05] address[0xdfefc000] gsi_base[24])
> [ 0.000000] IOAPIC[1]: apic_id 5, version 0, address 0xdfefc000, GSI 24-47
> [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
> [ 0.000000] ACPI: BIOS IRQ0 pin2 override ignored.
> [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
> [ 0.000000] ACPI: IRQ9 used by override.
I would like to look at those because they should tell the story of why
you can not find an IOAPIC for your GSIs.
It is possible that the explanation will simply be that the bug I fixed
made those GSIs usable (to linux) on your platform for the first time.
What hardware are you seeing this on?
Eric
^ permalink raw reply [flat|nested] 2+ messages in thread
* Re: ERROR: Unable to locate IOAPIC for GSI xx
@ 2010-07-07 11:31 Stuart
0 siblings, 0 replies; 2+ messages in thread
From: Stuart @ 2010-07-07 11:31 UTC (permalink / raw)
To: linux-kernel
[-- Attachment #1: Type: text/plain, Size: 454 bytes --]
Noticed the following errors on 2.6.35-rc4 (IBM Thinkpad R51 2889SG1)
(full details attached).
ERROR: Unable to locate IOAPIC for GSI 13
ERROR: Unable to locate IOAPIC for GSI 8
ERROR: Unable to locate IOAPIC for GSI 1
ERROR: Unable to locate IOAPIC for GSI 12
ERROR: Unable to locate IOAPIC for GSI 6
I saw a similar reported in June on 2.6.35-rc1 but I have not been able
to find any follow ups.
Is anyone currently investigating this ?
thanks
[-- Attachment #2: GSIError1 --]
[-- Type: text/plain, Size: 33701 bytes --]
Linux version 2.6.35-rc4 (root@Mars) (gcc version 4.5.0 (GCC) ) #1 Mon Jul 5 10:34:25 BST 2010
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000005f6e0000 (usable)
BIOS-e820: 000000005f6e0000 - 000000005f6f7000 (ACPI data)
BIOS-e820: 000000005f6f7000 - 000000005f6f9000 (ACPI NVS)
BIOS-e820: 000000005f700000 - 0000000060000000 (reserved)
BIOS-e820: 00000000ff800000 - 0000000100000000 (reserved)
Notice: NX (Execute Disable) protection missing in CPU or disabled in BIOS!
DMI present.
e820 update range: 0000000000000000 - 0000000000001000 (usable) ==> (reserved)
e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
last_pfn = 0x5f6e0 max_arch_pfn = 0x100000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-CFFFF write-protect
D0000-DBFFF uncachable
DC000-DFFFF write-back
E0000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 000000000 mask FC0000000 write-back
1 base 040000000 mask FE0000000 write-back
2 base 05FF00000 mask FFFF00000 uncachable
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
PAT not supported by CPU.
e820 update range: 0000000000001000 - 0000000000010000 (usable) ==> (reserved)
Scanning 1 areas for low memory corruption
modified physical RAM map:
modified: 0000000000000000 - 0000000000010000 (reserved)
modified: 0000000000010000 - 000000000009f000 (usable)
modified: 000000000009f000 - 00000000000a0000 (reserved)
modified: 00000000000dc000 - 0000000000100000 (reserved)
modified: 0000000000100000 - 000000005f6e0000 (usable)
modified: 000000005f6e0000 - 000000005f6f7000 (ACPI data)
modified: 000000005f6f7000 - 000000005f6f9000 (ACPI NVS)
modified: 000000005f700000 - 0000000060000000 (reserved)
modified: 00000000ff800000 - 0000000100000000 (reserved)
initial memory mapped : 0 - 01800000
init_memory_mapping: 0000000000000000-00000000377fe000
0000000000 - 0000400000 page 4k
0000400000 - 0037400000 page 2M
0037400000 - 00377fe000 page 4k
kernel direct mapping tables up to 377fe000 @ 10000-15000
ACPI: RSDP 000f6da0 00024 (v02 IBM )
ACPI: XSDT 5f6eb16b 0004C (v01 IBM TP-1V 00001290 LTP 00000000)
ACPI: FACP 5f6eb200 000F4 (v03 IBM TP-1V 00001290 IBM 00000001)
ACPI Warning: 32/64X length mismatch in Gpe1Block: 0/32 (20100428/tbfadt-526)
ACPI Warning: Optional field Gpe1Block has zero address or length: 0x000000000000102C/0x0 (20100428/tbfadt-557)
ACPI: DSDT 5f6eb3e7 0BA37 (v01 IBM TP-1V 00001290 MSFT 0100000E)
ACPI: FACS 5f6f8000 00040
ACPI: SSDT 5f6eb3b4 00033 (v01 IBM TP-1V 00001290 MSFT 0100000E)
ACPI: ECDT 5f6f6e1e 00052 (v01 IBM TP-1V 00001290 IBM 00000001)
ACPI: TCPA 5f6f6e70 00032 (v01 IBM TP-1V 00001290 PTL 00000001)
ACPI: BOOT 5f6f6fd8 00028 (v01 IBM TP-1V 00001290 LTP 00000001)
638MB HIGHMEM available.
887MB LOWMEM available.
mapped low ram: 0 - 377fe000
low ram: 0 - 377fe000
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
Normal 0x00001000 -> 0x000377fe
HighMem 0x000377fe -> 0x0005f6e0
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000010 -> 0x0000009f
0: 0x00000100 -> 0x0005f6e0
On node 0 totalpages: 390767
free_area_init_node: node 0, pgdat c1381e40, node_mem_map c1413200
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3951 pages, LIFO batch:0
Normal zone: 1744 pages used for memmap
Normal zone: 221486 pages, LIFO batch:31
HighMem zone: 1278 pages used for memmap
HighMem zone: 162276 pages, LIFO batch:31
Using APIC driver default
ACPI: PM-Timer IO Port: 0x1008
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
nr_irqs_gsi: 16
Allocating PCI resources starting at 60000000 (gap: 60000000:9f800000)
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 387713
Kernel command line: BOOT_IMAGE=Linux_2.6.35T ro root=307 userpte=nohigh i915.modeset=1 lapic pci=use_crs
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
Subtract (26 early reservations)
#0 [0001000000 - 000140a260] TEXT DATA BSS
#1 [000009f000 - 0000100000] BIOS reserved
#2 [000140b000 - 0001411128] BRK
#3 [0000010000 - 0000011000] PGTABLE
#4 [0001412000 - 0001413000] BOOTMEM
#5 [0001413000 - 0002003000] BOOTMEM
#6 [000140a280 - 000140a284] BOOTMEM
#7 [000140a2c0 - 000140a340] BOOTMEM
#8 [000140a340 - 000140a394] BOOTMEM
#9 [0002003000 - 0002005000] BOOTMEM
#10 [000140a3c0 - 000140a3fc] BOOTMEM
#11 [0002005000 - 0002007000] BOOTMEM
#12 [000140a400 - 000140a4fc] BOOTMEM
#13 [000140a500 - 000140a540] BOOTMEM
#14 [000140a540 - 000140a580] BOOTMEM
#15 [000140a580 - 000140a5c0] BOOTMEM
#16 [000140a5c0 - 000140a600] BOOTMEM
#17 [000140a600 - 000140a640] BOOTMEM
#18 [000140a640 - 000140a680] BOOTMEM
#19 [000140a680 - 000140a6c0] BOOTMEM
#20 [000140a6c0 - 000140a700] BOOTMEM
#21 [000140a700 - 000140a755] BOOTMEM
#22 [000140a780 - 000140a7d5] BOOTMEM
#23 [0002007000 - 000200b000] BOOTMEM
#24 [000200b000 - 000208b000] BOOTMEM
#25 [000208b000 - 00020cb000] BOOTMEM
Initializing HighMem for node 0 (000377fe:0005f6e0)
Memory: 1545868k/1563520k available (2629k kernel code, 17200k reserved, 970k data, 276k init, 654216k highmem)
virtual kernel memory layout:
fixmap : 0xfffa3000 - 0xfffff000 ( 368 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
.init : 0xc1385000 - 0xc13ca000 ( 276 kB)
.data : 0xc129159d - 0xc1383ff8 ( 970 kB)
.text : 0xc1000000 - 0xc129159d (2629 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
RCU-based detection of stalled CPUs is disabled.
Verbose stalled-CPUs detection is disabled.
NR_IRQS:288
Extended CMOS year: 2000
Console: colour VGA+ 80x25
console [tty0] enabled
Fast TSC calibration using PIT
Detected 1698.291 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 3397.10 BogoMIPS (lpj=5660970)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
mce: CPU supports 5 MCE banks
CPU0: Thermal monitoring enabled (TM2)
Performance Events: p6 PMU driver.
... version: 0
... bit width: 32
... generic registers: 2
... value mask: 00000000ffffffff
... max period: 000000007fffffff
... fixed-purpose events: 0
... event mask: 0000000000000003
CPU: Intel(R) Pentium(R) M processor 1.70GHz stepping 06
ACPI: Core revision 20100428
ACPI: setting ELCR to 0200 (from 0800)
Enabling APIC mode: Flat. Using 0 I/O APICs
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd8e6, last bus=5
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: EC description table is found, configuring boot EC
ACPI: Interpreter enabled
ACPI: (supports S0 S5)
ACPI: Using PIC for interrupt routing
ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
ACPI: Power Resource [PUBS] (on)
ACPI: ACPI Dock Station Driver: 3 docks/bays found
PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7]
pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff]
pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff]
pci_root PNP0A03:00: host bridge window [mem 0x000d0000-0x000d3fff]
pci_root PNP0A03:00: host bridge window [mem 0x000d4000-0x000d7fff]
pci_root PNP0A03:00: host bridge window [mem 0x000d8000-0x000dbfff]
pci_root PNP0A03:00: host bridge window [mem 0x60000000-0xfebfffff]
pci 0000:00:02.0: reg 10: [mem 0xe0000000-0xe7ffffff pref]
pci 0000:00:02.0: reg 14: [mem 0xd0000000-0xd007ffff]
pci 0000:00:02.0: reg 18: [io 0x1800-0x1807]
pci 0000:00:02.0: supports D1
pci 0000:00:02.1: reg 10: [mem 0xe8000000-0xefffffff pref]
pci 0000:00:02.1: reg 14: [mem 0xd0080000-0xd00fffff]
pci 0000:00:02.1: supports D1
pci 0000:00:1d.0: reg 20: [io 0x1820-0x183f]
pci 0000:00:1d.1: reg 20: [io 0x1840-0x185f]
pci 0000:00:1d.2: reg 20: [io 0x1860-0x187f]
pci 0000:00:1d.7: reg 10: [mem 0xd0100000-0xd01003ff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: quirk: [io 0x1000-0x107f] claimed by ICH4 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: [io 0x1180-0x11bf] claimed by ICH4 GPIO
pci 0000:00:1f.1: reg 10: [io 0x0000-0x0007]
pci 0000:00:1f.1: reg 14: [io 0x0000-0x0003]
pci 0000:00:1f.1: reg 18: [io 0x0000-0x0007]
pci 0000:00:1f.1: reg 1c: [io 0x0000-0x0003]
pci 0000:00:1f.1: reg 20: [io 0x1810-0x181f]
pci 0000:00:1f.1: reg 24: [mem 0x00000000-0x000003ff]
pci 0000:00:1f.3: reg 20: [io 0x1880-0x189f]
pci 0000:00:1f.5: reg 10: [io 0x1c00-0x1cff]
pci 0000:00:1f.5: reg 14: [io 0x18c0-0x18ff]
pci 0000:00:1f.5: reg 18: [mem 0xd0100c00-0xd0100dff]
pci 0000:00:1f.5: reg 1c: [mem 0xd0100800-0xd01008ff]
pci 0000:00:1f.5: PME# supported from D0 D3hot D3cold
pci 0000:00:1f.5: PME# disabled
pci 0000:00:1f.6: reg 10: [io 0x2400-0x24ff]
pci 0000:00:1f.6: reg 14: [io 0x2000-0x207f]
pci 0000:00:1f.6: PME# supported from D0 D3hot D3cold
pci 0000:00:1f.6: PME# disabled
pci 0000:02:00.0: reg 10: [mem 0xb0000000-0xb0000fff]
pci 0000:02:00.0: supports D1 D2
pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:02:00.0: PME# disabled
pci 0000:02:08.0: reg 10: [mem 0xd0200000-0xd0200fff]
pci 0000:02:08.0: reg 14: [io 0x7000-0x703f]
pci 0000:02:08.0: supports D1 D2
pci 0000:02:08.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:02:08.0: PME# disabled
pci 0000:00:1e.0: PCI bridge to [bus 02-05] (subtractive decode)
pci 0000:00:1e.0: bridge window [io 0x3000-0x7fff]
pci 0000:00:1e.0: bridge window [mem 0xd0200000-0xdfffffff]
pci 0000:00:1e.0: bridge window [mem 0xf0000000-0xf7ffffff pref]
pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x000d0000-0x000d3fff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x000d4000-0x000d7fff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x000d8000-0x000dbfff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x60000000-0xfebfffff] (subtractive decode)
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11)
vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: pci_cache_line_size set to 64 bytes
reserve RAM buffer: 000000000009f000 - 000000000009ffff
reserve RAM buffer: 000000005f6e0000 - 000000005fffffff
Switching to clocksource tsc
pnp: PnP ACPI init
ACPI: bus type pnp registered
ERROR: Unable to locate IOAPIC for GSI 13
ERROR: Unable to locate IOAPIC for GSI 8
ERROR: Unable to locate IOAPIC for GSI 1
ERROR: Unable to locate IOAPIC for GSI 12
ERROR: Unable to locate IOAPIC for GSI 6
pnp: PnP ACPI: found 12 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
system 00:00: [mem 0x00000000-0x0009ffff] could not be reserved
system 00:00: [mem 0x000c0000-0x000c3fff] could not be reserved
system 00:00: [mem 0x000c4000-0x000c7fff] could not be reserved
system 00:00: [mem 0x000c8000-0x000cbfff] has been reserved
system 00:00: [mem 0x000cc000-0x000cffff] could not be reserved
system 00:00: [mem 0x000dc000-0x000dffff] could not be reserved
system 00:00: [mem 0x000e0000-0x000e3fff] could not be reserved
system 00:00: [mem 0x000e4000-0x000e7fff] could not be reserved
system 00:00: [mem 0x000e8000-0x000ebfff] could not be reserved
system 00:00: [mem 0x000ec000-0x000effff] could not be reserved
system 00:00: [mem 0x000f0000-0x000fffff] could not be reserved
system 00:00: [mem 0x00100000-0x5fffffff] could not be reserved
system 00:00: [mem 0xfec00000-0xffffffff] could not be reserved
system 00:02: [io 0x1000-0x107f] has been reserved
system 00:02: [io 0x1180-0x11bf] has been reserved
system 00:02: [io 0x15e0-0x15ef] has been reserved
system 00:02: [io 0x1600-0x167f] has been reserved
pci 0000:00:1f.1: BAR 5: assigned [mem 0x60000000-0x600003ff]
pci 0000:00:1f.1: BAR 5: set to [mem 0x60000000-0x600003ff] (PCI address [0x60000000-0x600003ff]
pci 0000:02:00.0: BAR 9: assigned [mem 0xf0000000-0xf3ffffff pref]
pci 0000:02:00.0: BAR 10: assigned [mem 0xd4000000-0xd7ffffff]
pci 0000:02:00.0: BAR 7: assigned [io 0x3000-0x30ff]
pci 0000:02:00.0: BAR 8: assigned [io 0x3400-0x34ff]
pci 0000:02:00.0: CardBus bridge to [bus 03-04]
pci 0000:02:00.0: bridge window [io 0x3000-0x30ff]
pci 0000:02:00.0: bridge window [io 0x3400-0x34ff]
pci 0000:02:00.0: bridge window [mem 0xf0000000-0xf3ffffff pref]
pci 0000:02:00.0: bridge window [mem 0xd4000000-0xd7ffffff]
pci 0000:00:1e.0: PCI bridge to [bus 02-05]
pci 0000:00:1e.0: bridge window [io 0x3000-0x7fff]
pci 0000:00:1e.0: bridge window [mem 0xd0200000-0xdfffffff]
pci 0000:00:1e.0: bridge window [mem 0xf0000000-0xf7ffffff pref]
pci 0000:00:1e.0: setting latency timer to 64
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
pci 0000:02:00.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000d3fff]
pci_bus 0000:00: resource 8 [mem 0x000d4000-0x000d7fff]
pci_bus 0000:00: resource 9 [mem 0x000d8000-0x000dbfff]
pci_bus 0000:00: resource 10 [mem 0x60000000-0xfebfffff]
pci_bus 0000:02: resource 0 [io 0x3000-0x7fff]
pci_bus 0000:02: resource 1 [mem 0xd0200000-0xdfffffff]
pci_bus 0000:02: resource 2 [mem 0xf0000000-0xf7ffffff pref]
pci_bus 0000:02: resource 4 [io 0x0000-0x0cf7]
pci_bus 0000:02: resource 5 [io 0x0d00-0xffff]
pci_bus 0000:02: resource 6 [mem 0x000a0000-0x000bffff]
pci_bus 0000:02: resource 7 [mem 0x000d0000-0x000d3fff]
pci_bus 0000:02: resource 8 [mem 0x000d4000-0x000d7fff]
pci_bus 0000:02: resource 9 [mem 0x000d8000-0x000dbfff]
pci_bus 0000:02: resource 10 [mem 0x60000000-0xfebfffff]
pci_bus 0000:03: resource 0 [io 0x3000-0x30ff]
pci_bus 0000:03: resource 1 [io 0x3400-0x34ff]
pci_bus 0000:03: resource 2 [mem 0xf0000000-0xf3ffffff pref]
pci_bus 0000:03: resource 3 [mem 0xd4000000-0xd7ffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
UDP hash table entries: 512 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 512 (order: 1, 8192 bytes)
pci 0000:00:02.0: Boot video device
pci 0000:02:08.0: Firmware left e100 interrupts enabled; disabling
PCI: CLS 32 bytes, default 64
Simple Boot Flag at 0x35 set to 0x1
Scanning for low memory corruption every 60 seconds
highmem bounce pool size: 64 pages
msgmni has been set to 1741
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler cfq registered (default)
input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input0
ACPI: Lid Switch [LID]
input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1
ACPI: Sleep Button [SLPB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
ACPI: Power Button [PWRF]
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/LNXVIDEO:00/input/input3
ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux agpgart interface v0.103
agpgart-intel 0000:00:00.0: Intel 855GM Chipset
agpgart-intel 0000:00:00.0: detected 8060K stolen memory
agpgart-intel 0000:00:00.0: AGP aperture is 128M @ 0xe0000000
[drm] Initialized drm 1.1.0 20060810
i915 0000:00:02.0: power state changed by ACPI to D0
i915 0000:00:02.0: power state changed by ACPI to D0
i915 0000:00:02.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
i915 0000:00:02.0: setting latency timer to 64
[drm] set up 7M of stolen space
[drm] initialized overlay support
fbcon: inteldrmfb (fb0) is primary device
Console: switching to colour frame buffer device 128x48
fb0: inteldrmfb frame buffer device
drm: registered panic notifier
Slow work thread pool: Starting up
Slow work thread pool: Ready
[drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
brd: module loaded
Uniform Multi-Platform E-IDE driver
piix 0000:00:1f.1: IDE controller (0x8086:0x24ca rev 0x01)
PIIX_IDE 0000:00:1f.1: enabling device (0005 -> 0007)
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
PIIX_IDE 0000:00:1f.1: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
piix 0000:00:1f.1: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1810-0x1817
ide1: BM-DMA at 0x1818-0x181f
Probing IDE interface ide0...
hda: ST9160821A, ATA DISK drive
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/100 mode selected
Probing IDE interface ide1...
hdc: DW-225, ATAPI CD/DVD-ROM drive
hdc: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hdc: UDMA/33 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
ide-gd driver 1.18
hda: max request size: 512KiB
hda: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63
hda: cache flushes supported
hda: hda1 hda2 hda3 < hda5 hda6 hda7 hda8 hda9 hda10 >
PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
Using IPI Shortcut mode
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
EXT4-fs (hda7): mounted filesystem with ordered data mode. Opts: (null)
VFS: Mounted root (ext4 filesystem) readonly on device 3:7.
Freeing unused kernel memory: 276k freed
NET: Registered protocol family 1
ACPI: acpi_idle registered with cpuidle
Marking TSC unstable due to TSC halts in idle
Switching to clocksource acpi_pm
udev: starting version 142
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
i801_smbus 0000:00:1f.3: PCI INT B -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
intel_rng: FWH not detected
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THM0] (39 C)
e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11
e100 0000:02:08.0: PCI INT A -> Link[LNKE] -> GSI 11 (level, low) -> IRQ 11
e100 0000:02:08.0: PME# disabled
Non-volatile memory driver v1.3
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
Floppy drive(s): fd0 is 1.44M
ACPI: AC Adapter [AC] (on-line)
ide-cd driver 5.00
FDC 0 is a National Semiconductor PC87306
ide-cd: hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 1654kB Cache
Uniform CD-ROM driver Revision: 3.20
serial 00:0a: activated
00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A
ACPI: Battery Slot [BAT0] (battery present)
rtc_cmos 00:06: RTC can wake from S4
rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, 114 bytes nvram
Intel ICH 0000:00:1f.5: PCI INT B -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
Intel ICH 0000:00:1f.5: setting latency timer to 64
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
thinkpad_acpi: ThinkPad ACPI Extras v0.24
thinkpad_acpi: http://ibm-acpi.sf.net/
thinkpad_acpi: ThinkPad BIOS 1VET71WW (1.29 ), EC 1VHT28WW-1.04
thinkpad_acpi: IBM ThinkPad R51, model 2889SG1
usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
thinkpad_acpi: detected a 8-level brightness capable ThinkPad
Registered led device: tpacpi::thinklight
Registered led device: tpacpi::power
Registered led device: tpacpi::standby
e100 0000:02:08.0: eth0: addr 0xd0200000, irq 11, MAC addr 00:11:25:ae:9d:9e
yenta_cardbus 0000:02:00.0: CardBus bridge found [1014:0512]
yenta_cardbus 0000:02:00.0: Using INTVAL to route CSC interrupts to PCI
yenta_cardbus 0000:02:00.0: Routing CardBus interrupts to PCI
yenta_cardbus 0000:02:00.0: TI: mfunc 0x01d21022, devctl 0x64
thinkpad_acpi: brightness: will use unverified default: brightness_mode=3
thinkpad_acpi: brightness: please report to ibm-acpi-devel@lists.sourceforge.net whether it works well or not on your ThinkPad
thinkpad_acpi: Console audio control enabled, mode: monitor (read only)
input: ThinkPad Extra Buttons as /devices/platform/thinkpad_acpi/input/input5
Synaptics Touchpad, model: 1, fw: 5.9, id: 0x2c6ab1, caps: 0x884793/0x0/0x0
serio: Synaptics pass-through port at isa0060/serio1/input0
yenta_cardbus 0000:02:00.0: ISA IRQ mask 0x04b8, PCI irq 11
yenta_cardbus 0000:02:00.0: Socket status: 30000020
yenta_cardbus 0000:02:00.0: pcmcia: parent PCI bridge window: [io 0x3000-0x7fff]
pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3000-0x7fff: excluding 0x3000-0x30ff 0x3400-0x34ff
input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input6
0x7000-0x703f
yenta_cardbus 0000:02:00.0: pcmcia: parent PCI bridge window: [mem 0xd0200000-0xdfffffff]
pcmcia_socket pcmcia_socket0: cs: memory probe 0xd0200000-0xdfffffff: excluding 0xd0200000-0xd09fffff 0xd3a00000-0xd81fffff 0xdfa00000-0xe01fffff
yenta_cardbus 0000:02:00.0: pcmcia: parent PCI bridge window: [mem 0xf0000000-0xf7ffffff pref]
pcmcia_socket pcmcia_socket0: cs: memory probe 0xf0000000-0xf7ffffff: excluding 0xf0000000-0xf7ffffff
intel8x0_measure_ac97_clock: measured 52741 usecs (2541 samples)
intel8x0: clocking to 48000
serial 0000:00:1f.6: PCI INT B -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
serial 0000:00:1f.6: PCI INT B disabled
ehci_hcd 0000:00:1d.7: power state changed by ACPI to D0
ehci_hcd 0000:00:1d.7: power state changed by ACPI to D0
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
ehci_hcd 0000:00:1d.7: PCI INT D -> Link[LNKH] -> GSI 11 (level, low) -> IRQ 11
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 11, io mem 0xd0100000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.35-rc4 ehci_hcd
usb usb1: SerialNumber: 0000:00:1d.7
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1d.0: power state changed by ACPI to D0
uhci_hcd 0000:00:1d.0: power state changed by ACPI to D0
uhci_hcd 0000:00:1d.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 11, io base 0x00001820
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.35-rc4 uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.0
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: power state changed by ACPI to D0
uhci_hcd 0000:00:1d.1: power state changed by ACPI to D0
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
uhci_hcd 0000:00:1d.1: PCI INT B -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 11, io base 0x00001840
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.35-rc4 uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.1
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: PCI INT C -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 11, io base 0x00001860
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.35-rc4 uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.2
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
Adding 2097144k swap on /dev/hda6. Priority:1 extents:1 across:2097144k
EXT4-fs (hda7): re-mounted. Opts: (null)
usb 1-1: new high speed USB device using ehci_hcd and address 2
usb 1-1: New USB device found, idVendor=04b3, idProduct=4482
usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
pcmcia_socket pcmcia_socket0: pccard: CardBus card inserted into slot 0
pci 0000:03:00.0: reg 10: [mem 0xd0000000-0xd000ffff]
pci 0000:03:00.0: reg 14: [mem 0xc0000000-0xc000ffff]
pci 0000:03:00.0: BAR 0: assigned [mem 0xd4000000-0xd400ffff]
pci 0000:03:00.0: BAR 0: set to [mem 0xd4000000-0xd400ffff] (PCI address [0xd4000000-0xd400ffff]
pci 0000:03:00.0: BAR 1: assigned [mem 0xd4010000-0xd401ffff]
pci 0000:03:00.0: BAR 1: set to [mem 0xd4010000-0xd401ffff] (PCI address [0xd4010000-0xd401ffff]
usb 1-1.4: new high speed USB device using ehci_hcd and address 3
EXT4-fs (hda7): re-mounted. Opts: (null)
usb 1-1.4: New USB device found, idVendor=05e3, idProduct=0608
usb 1-1.4: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 1-1.4: Product: USB2.0 Hub
hub 1-1.4:1.0: USB hub found
hub 1-1.4:1.0: 4 ports detected
EXT4-fs (hda1): mounted filesystem with ordered data mode. Opts: (null)
EXT4-fs (hda8): mounted filesystem with ordered data mode. Opts: (null)
EXT4-fs (hda9): mounted filesystem with ordered data mode. Opts: (null)
EXT4-fs (hda10): mounted filesystem with ordered data mode. Opts: (null)
usb 1-1.4.2: new low speed USB device using ehci_hcd and address 4
usb 1-1.4.2: New USB device found, idVendor=046d, idProduct=c018
usb 1-1.4.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1.4.2: Product: Logitech USB Optical Mouse
usb 1-1.4.2: Manufacturer: Logitech
input: Logitech Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:1d.7/usb1/1-1/1-1.4/1-1.4.2/1-1.4.2:1.0/input/input7
generic-usb 0003:046D:C018.0001: input: USB HID v1.11 Mouse [Logitech Logitech USB Optical Mouse] on usb-0000:00:1d.7-1.4.2/input0
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
usb 1-1.4.3: new low speed USB device using ehci_hcd and address 5
usb 1-1.4.3: New USB device found, idVendor=06f2, idProduct=0011
usb 1-1.4.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1.4.3: Product: USB KVM Switch
usb 1-1.4.3: Manufacturer: Justcom Technology
input: Justcom Technology USB KVM Switch as /devices/pci0000:00/0000:00:1d.7/usb1/1-1/1-1.4/1-1.4.3/1-1.4.3:1.0/input/input8
generic-usb 0003:06F2:0011.0002: input: USB HID v1.10 Keyboard [Justcom Technology USB KVM Switch] on usb-0000:00:1d.7-1.4.3/input0
input: Justcom Technology USB KVM Switch as /devices/pci0000:00/0000:00:1d.7/usb1/1-1/1-1.4/1-1.4.3/1-1.4.3:1.1/input/input9
generic-usb 0003:06F2:0011.0003: input: USB HID v1.10 Mouse [Justcom Technology USB KVM Switch] on usb-0000:00:1d.7-1.4.3/input1
usb 1-1.4.4: new high speed USB device using ehci_hcd and address 6
usb 1-1.4.4: New USB device found, idVendor=05e3, idProduct=0608
usb 1-1.4.4: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 1-1.4.4: Product: USB2.0 Hub
hub 1-1.4.4:1.0: USB hub found
hub 1-1.4.4:1.0: 4 ports detected
usb 1-1.4.4.4: new high speed USB device using ehci_hcd and address 7
usb 1-1.4.4.4: New USB device found, idVendor=0424, idProduct=2504
usb 1-1.4.4.4: New USB device strings: Mfr=0, Product=0, SerialNumber=0
hub 1-1.4.4.4:1.0: USB hub found
hub 1-1.4.4.4:1.0: 4 ports detected
microcode: CPU0 sig=0x6d6, pf=0x20, revision=0x18
microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
IBM TrackPoint firmware: 0x0e, buttons: 3/3
input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/serio2/input/input10
e100 0000:02:08.0: eth0: NIC Link is Up 100 Mbps Full Duplex
Disabling lock debugging due to kernel taint
ndiswrapper version 1.56 loaded (smp=no, preempt=no)
ndiswrapper: driver wg511v2 (NETGEAR,02/22/2005,3.1.1.7) loaded
ndiswrapper 0000:03:00.0: enabling device (0000 -> 0002)
ndiswrapper 0000:03:00.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
ndiswrapper 0000:03:00.0: setting latency timer to 64
ndiswrapper: using IRQ 11
wlan0: ethernet device 00:1e:2a:b4:00:dd using NDIS driver: wg511v2, version: 0x3000036, NDIS version: 0x501, vendor: 'NDIS Network Adapter', 11AB:1FAA.5.conf
wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK
usbcore: registered new interface driver ndiswrapper
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
usb 1-1.4.4: USB disconnect, address 6
usb 1-1.4.4.4: USB disconnect, address 7
usb 1-1.4.2: USB disconnect, address 4
usb 1-1.4.2: new low speed USB device using ehci_hcd and address 8
usb 1-1.4.2: New USB device found, idVendor=046d, idProduct=c018
usb 1-1.4.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1.4.2: Product: Logitech USB Optical Mouse
usb 1-1.4.2: Manufacturer: Logitech
input: Logitech Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:1d.7/usb1/1-1/1-1.4/1-1.4.2/1-1.4.2:1.0/input/input11
generic-usb 0003:046D:C018.0004: input: USB HID v1.11 Mouse [Logitech Logitech USB Optical Mouse] on usb-0000:00:1d.7-1.4.2/input0
usb 1-1.4.4: new high speed USB device using ehci_hcd and address 9
usb 1-1.4.4: New USB device found, idVendor=05e3, idProduct=0608
usb 1-1.4.4: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 1-1.4.4: Product: USB2.0 Hub
hub 1-1.4.4:1.0: USB hub found
hub 1-1.4.4:1.0: 4 ports detected
usb 1-1.4.4.4: new high speed USB device using ehci_hcd and address 10
usb 1-1.4.4.4: New USB device found, idVendor=0424, idProduct=2504
usb 1-1.4.4.4: New USB device strings: Mfr=0, Product=0, SerialNumber=0
hub 1-1.4.4.4:1.0: USB hub found
hub 1-1.4.4.4:1.0: 4 ports detected
usb 1-1.4.4: USB disconnect, address 9
usb 1-1.4.4.4: USB disconnect, address 10
usb 1-1.4.2: USB disconnect, address 8
usb 1-1.4.2: new low speed USB device using ehci_hcd and address 11
usb 1-1.4.2: New USB device found, idVendor=046d, idProduct=c018
usb 1-1.4.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1.4.2: Product: Logitech USB Optical Mouse
usb 1-1.4.2: Manufacturer: Logitech
input: Logitech Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:1d.7/usb1/1-1/1-1.4/1-1.4.2/1-1.4.2:1.0/input/input12
generic-usb 0003:046D:C018.0005: input: USB HID v1.11 Mouse [Logitech Logitech USB Optical Mouse] on usb-0000:00:1d.7-1.4.2/input0
usb 1-1.4.4: new high speed USB device using ehci_hcd and address 12
usb 1-1.4.4: New USB device found, idVendor=05e3, idProduct=0608
usb 1-1.4.4: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 1-1.4.4: Product: USB2.0 Hub
hub 1-1.4.4:1.0: USB hub found
hub 1-1.4.4:1.0: 4 ports detected
usb 1-1.4.4.4: new high speed USB device using ehci_hcd and address 13
usb 1-1.4.4.4: New USB device found, idVendor=0424, idProduct=2504
usb 1-1.4.4.4: New USB device strings: Mfr=0, Product=0, SerialNumber=0
hub 1-1.4.4.4:1.0: USB hub found
hub 1-1.4.4.4:1.0: 4 ports detected
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2010-07-07 11:33 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2010-07-07 11:31 ERROR: Unable to locate IOAPIC for GSI xx Stuart
[not found] <AANLkTilT0cPU8y2m4ZeatfvtflAagSyQEP9JubqZ6TeW@mail.gmail.com>
2010-06-03 9:08 ` Eric W. Biederman
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox