* pch_uart: reference clock on CM-iTC
@ 2011-03-07 9:31 Denis Turischev
2011-03-07 20:07 ` Greg KH
0 siblings, 1 reply; 8+ messages in thread
From: Denis Turischev @ 2011-03-07 9:31 UTC (permalink / raw)
To: Greg Kroah-Hartman; +Cc: linux-kernel, Tomoya MORINAGA
Default clock source for UARTs on Topcliff is external UART_CLK.
On CM-iTC USB_48MHz is used unstead. After VCO2PLL and DIV
manipulations UARTs will receive 192 MHz.
Clock manipulations on Topcliff are controlled in pch_phub.c
Signed-off-by: Denis Turischev <denis@compulab.co.il>
---
drivers/misc/pch_phub.c | 16 ++++++++++++++++
drivers/tty/serial/pch_uart.c | 9 +++++++--
2 files changed, 23 insertions(+), 2 deletions(-)
diff --git a/drivers/misc/pch_phub.c b/drivers/misc/pch_phub.c
index 744b804..50cb839 100644
--- a/drivers/misc/pch_phub.c
+++ b/drivers/misc/pch_phub.c
@@ -27,6 +27,7 @@
#include <linux/mutex.h>
#include <linux/if_ether.h>
#include <linux/ctype.h>
+#include <linux/dmi.h>
#define PHUB_STATUS 0x00 /* Status Register offset */
#define PHUB_CONTROL 0x04 /* Control Register offset */
@@ -41,6 +42,13 @@
#define PCH_MINOR_NOS 1
#define CLKCFG_CAN_50MHZ 0x12000000
#define CLKCFG_CANCLK_MASK 0xFF000000
+#define CLKCFG_UART_MASK 0xFFFFFF
+
+/* CM-iTC */
+#define CLKCFG_UART_48MHZ (1 << 16)
+#define CLKCFG_BAUDDIV (2 << 20)
+#define CLKCFG_PLL2VCO (8 << 9)
+#define CLKCFG_UARTCLKSEL (1 << 18)
/* SROM ACCESS Macro */
#define PCH_WORD_ADDR_MASK (~((1 << 2) - 1))
@@ -607,6 +615,14 @@ static int __devinit pch_phub_probe(struct pci_dev *pdev,
pch_phub_read_modify_write_reg(chip, (unsigned int)CLKCFG_REG_OFFSET,
CLKCFG_CAN_50MHZ, CLKCFG_CANCLK_MASK);
+ /* quirk for CM-iTC board */
+ if (strstr(dmi_get_system_info(DMI_BOARD_NAME), "CM-iTC"))
+ pch_phub_read_modify_write_reg(chip,
+ (unsigned int)CLKCFG_REG_OFFSET,
+ CLKCFG_UART_48MHZ | CLKCFG_BAUDDIV |
+ CLKCFG_PLL2VCO | CLKCFG_UARTCLKSEL,
+ CLKCFG_UART_MASK);
+
/* set the prefech value */
iowrite32(0x000affaa, chip->pch_phub_base_address + 0x14);
/* set the interrupt delay value */
diff --git a/drivers/tty/serial/pch_uart.c b/drivers/tty/serial/pch_uart.c
index 70a6145..9689ac6 100644
--- a/drivers/tty/serial/pch_uart.c
+++ b/drivers/tty/serial/pch_uart.c
@@ -21,6 +21,7 @@
#include <linux/serial_core.h>
#include <linux/interrupt.h>
#include <linux/io.h>
+#include <linux/dmi.h>
#include <linux/dmaengine.h>
#include <linux/pch_dma.h>
@@ -1267,14 +1268,18 @@ static struct eg20t_port *pch_uart_init_port(struct pci_dev *pdev,
if (!rxbuf)
goto init_port_free_txbuf;
+ base_baud = 1843200; /* 1.8432MHz */
+
+ /* quirk for CM-iTC board */
+ if (strstr(dmi_get_system_info(DMI_BOARD_NAME), "CM-iTC"))
+ base_baud = 192000000; /* 192.0MHz */
+
switch (port_type) {
case PORT_UNKNOWN:
fifosize = 256; /* UART0 */
- base_baud = 1843200; /* 1.8432MHz */
break;
case PORT_8250:
fifosize = 64; /* UART1~3 */
- base_baud = 1843200; /* 1.8432MHz */
break;
default:
dev_err(&pdev->dev, "Invalid Port Type(=%d)\n", port_type);
--
1.7.0.4
--
Denis
^ permalink raw reply related [flat|nested] 8+ messages in thread* Re: pch_uart: reference clock on CM-iTC
2011-03-07 9:31 pch_uart: reference clock on CM-iTC Denis Turischev
@ 2011-03-07 20:07 ` Greg KH
2011-03-08 12:22 ` [PATCH v2] " Denis Turischev
0 siblings, 1 reply; 8+ messages in thread
From: Greg KH @ 2011-03-07 20:07 UTC (permalink / raw)
To: Denis Turischev; +Cc: Greg Kroah-Hartman, linux-kernel, Tomoya MORINAGA
On Mon, Mar 07, 2011 at 11:31:44AM +0200, Denis Turischev wrote:
> Default clock source for UARTs on Topcliff is external UART_CLK.
> On CM-iTC USB_48MHz is used unstead. After VCO2PLL and DIV
> manipulations UARTs will receive 192 MHz.
> Clock manipulations on Topcliff are controlled in pch_phub.c
>
> Signed-off-by: Denis Turischev <denis@compulab.co.il>
> ---
> drivers/misc/pch_phub.c | 16 ++++++++++++++++
> drivers/tty/serial/pch_uart.c | 9 +++++++--
This patch fails to apply to my tree, care to redo it against the
linux-next tree and resend it?
thanks,
greg k-h
^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH v2] pch_uart: reference clock on CM-iTC
2011-03-07 20:07 ` Greg KH
@ 2011-03-08 12:22 ` Denis Turischev
2011-03-09 23:42 ` Greg KH
0 siblings, 1 reply; 8+ messages in thread
From: Denis Turischev @ 2011-03-08 12:22 UTC (permalink / raw)
To: Greg KH; +Cc: Greg Kroah-Hartman, linux-kernel, Tomoya MORINAGA
Default clock source for UARTs on Topcliff is external UART_CLK.
On CM-iTC USB_48MHz is used instead. After VCO2PLL and DIV
manipulations UARTs will receive 192 MHz.
Clock manipulations on Topcliff are controlled in pch_phub.c
v2: redone against the linux-next tree
Signed-off-by: Denis Turischev <denis@compulab.co.il>
---
drivers/misc/pch_phub.c | 19 +++++++++++++++++++
drivers/tty/serial/pch_uart.c | 9 +++++++--
2 files changed, 26 insertions(+), 2 deletions(-)
diff --git a/drivers/misc/pch_phub.c b/drivers/misc/pch_phub.c
index 98bffc4..a85c4a3 100644
--- a/drivers/misc/pch_phub.c
+++ b/drivers/misc/pch_phub.c
@@ -27,6 +27,7 @@
#include <linux/mutex.h>
#include <linux/if_ether.h>
#include <linux/ctype.h>
+#include <linux/dmi.h>
#define PHUB_STATUS 0x00 /* Status Register offset */
#define PHUB_CONTROL 0x04 /* Control Register offset */
@@ -46,6 +47,13 @@
#define PCH_MINOR_NOS 1
#define CLKCFG_CAN_50MHZ 0x12000000
#define CLKCFG_CANCLK_MASK 0xFF000000
+#define CLKCFG_UART_MASK 0xFFFFFF
+
+/* CM-iTC */
+#define CLKCFG_UART_48MHZ (1 << 16)
+#define CLKCFG_BAUDDIV (2 << 20)
+#define CLKCFG_PLL2VCO (8 << 9)
+#define CLKCFG_UARTCLKSEL (1 << 18)
/* Macros for ML7213 */
#define PCI_VENDOR_ID_ROHM 0x10db
@@ -618,6 +626,17 @@ static int __devinit pch_phub_probe(struct pci_dev *pdev,
CLKCFG_CAN_50MHZ,
CLKCFG_CANCLK_MASK);
+ /* quirk for CM-iTC board */
+ if (strstr(dmi_get_system_info(DMI_BOARD_NAME), "CM-iTC"))
+ pch_phub_read_modify_write_reg(chip,
+ (unsigned int)CLKCFG_REG_OFFSET,
+ CLKCFG_UART_48MHZ |
+ CLKCFG_BAUDDIV |
+ CLKCFG_PLL2VCO |
+ CLKCFG_UARTCLKSEL,
+ CLKCFG_UART_MASK);
+
+
/* set the prefech value */
iowrite32(0x000affaa, chip->pch_phub_base_address + 0x14);
/* set the interrupt delay value */
diff --git a/drivers/tty/serial/pch_uart.c b/drivers/tty/serial/pch_uart.c
index 7aba41f..26403b8 100644
--- a/drivers/tty/serial/pch_uart.c
+++ b/drivers/tty/serial/pch_uart.c
@@ -20,6 +20,7 @@
#include <linux/serial_core.h>
#include <linux/interrupt.h>
#include <linux/io.h>
+#include <linux/dmi.h>
#include <linux/dmaengine.h>
#include <linux/pch_dma.h>
@@ -1403,14 +1404,18 @@ static struct eg20t_port *pch_uart_init_port(struct pci_dev *pdev,
if (!rxbuf)
goto init_port_free_txbuf;
+ base_baud = 1843200; /* 1.8432MHz */
+
+ /* quirk for CM-iTC board */
+ if (strstr(dmi_get_system_info(DMI_BOARD_NAME), "CM-iTC"))
+ base_baud = 192000000; /* 192.0MHz */
+
switch (port_type) {
case PORT_UNKNOWN:
fifosize = 256; /* EG20T/ML7213: UART0 */
- base_baud = 1843200; /* 1.8432MHz */
break;
case PORT_8250:
fifosize = 64; /* EG20T:UART1~3 ML7213: UART1~2*/
- base_baud = 1843200; /* 1.8432MHz */
break;
default:
dev_err(&pdev->dev, "Invalid Port Type(=%d)\n", port_type);
--
1.7.0.4
^ permalink raw reply related [flat|nested] 8+ messages in thread* Re: [PATCH v2] pch_uart: reference clock on CM-iTC
2011-03-08 12:22 ` [PATCH v2] " Denis Turischev
@ 2011-03-09 23:42 ` Greg KH
2011-03-10 13:14 ` [PATCH v3] " Denis Turischev
0 siblings, 1 reply; 8+ messages in thread
From: Greg KH @ 2011-03-09 23:42 UTC (permalink / raw)
To: Denis Turischev; +Cc: Greg Kroah-Hartman, linux-kernel, Tomoya MORINAGA
On Tue, Mar 08, 2011 at 02:22:23PM +0200, Denis Turischev wrote:
> Default clock source for UARTs on Topcliff is external UART_CLK.
> On CM-iTC USB_48MHz is used instead. After VCO2PLL and DIV
> manipulations UARTs will receive 192 MHz.
> Clock manipulations on Topcliff are controlled in pch_phub.c
>
> v2: redone against the linux-next tree
Are you sure? I still get the following conflicts when applying it:
patching file drivers/misc/pch_phub.c
Hunk #2 succeeded at 42 with fuzz 2 (offset -5 lines).
Hunk #3 FAILED at 626.
1 out of 3 hunks FAILED -- saving rejects to file drivers/misc/pch_phub.c.rej
patching file drivers/tty/serial/pch_uart.c
Hunk #1 succeeded at 21 (offset 1 line).
Hunk #2 succeeded at 1405 (offset 1 line).
confused,
greg k-h
^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH v3] pch_uart: reference clock on CM-iTC
2011-03-09 23:42 ` Greg KH
@ 2011-03-10 13:14 ` Denis Turischev
2011-03-11 22:25 ` Greg KH
0 siblings, 1 reply; 8+ messages in thread
From: Denis Turischev @ 2011-03-10 13:14 UTC (permalink / raw)
To: Greg KH; +Cc: Greg Kroah-Hartman, linux-kernel, Tomoya MORINAGA
Default clock source for UARTs on Topcliff is external UART_CLK.
On CM-iTC USB_48MHz is used instead. After VCO2PLL and DIV
manipulations UARTs will receive 192 MHz.
Clock manipulations on Topcliff are controlled in pch_phub.c
v2: redone against the linux-next tree
v3: redone against linux/kernel/git/next/linux-next.git snapshot
Signed-off-by: Denis Turischev <denis@compulab.co.il>
---
diff -Nru linux-next-20110310.orig/drivers/misc/pch_phub.c linux-next-20110310/drivers/misc/pch_phub.c
--- linux-next-20110310.orig/drivers/misc/pch_phub.c 2011-03-10 08:31:30.000000000 +0200
+++ linux-next-20110310/drivers/misc/pch_phub.c 2011-03-10 14:42:05.110978473 +0200
@@ -27,6 +27,7 @@
#include <linux/mutex.h>
#include <linux/if_ether.h>
#include <linux/ctype.h>
+#include <linux/dmi.h>
#define PHUB_STATUS 0x00 /* Status Register offset */
#define PHUB_CONTROL 0x04 /* Control Register offset */
@@ -46,6 +47,13 @@
#define PCH_MINOR_NOS 1
#define CLKCFG_CAN_50MHZ 0x12000000
#define CLKCFG_CANCLK_MASK 0xFF000000
+#define CLKCFG_UART_MASK 0xFFFFFF
+
+/* CM-iTC */
+#define CLKCFG_UART_48MHZ (1 << 16)
+#define CLKCFG_BAUDDIV (2 << 20)
+#define CLKCFG_PLL2VCO (8 << 9)
+#define CLKCFG_UARTCLKSEL (1 << 18)
/* Macros for ML7213 */
#define PCI_VENDOR_ID_ROHM 0x10db
@@ -618,6 +626,14 @@
CLKCFG_CAN_50MHZ,
CLKCFG_CANCLK_MASK);
+ /* quirk for CM-iTC board */
+ if (strstr(dmi_get_system_info(DMI_BOARD_NAME), "CM-iTC"))
+ pch_phub_read_modify_write_reg(chip,
+ (unsigned int)CLKCFG_REG_OFFSET,
+ CLKCFG_UART_48MHZ | CLKCFG_BAUDDIV |
+ CLKCFG_PLL2VCO | CLKCFG_UARTCLKSEL,
+ CLKCFG_UART_MASK);
+
/* set the prefech value */
iowrite32(0x000affaa, chip->pch_phub_base_address + 0x14);
/* set the interrupt delay value */
diff -Nru linux-next-20110310.orig/drivers/tty/serial/pch_uart.c linux-next-20110310/drivers/tty/serial/pch_uart.c
--- linux-next-20110310.orig/drivers/tty/serial/pch_uart.c 2011-03-10 08:31:30.000000000 +0200
+++ linux-next-20110310/drivers/tty/serial/pch_uart.c 2011-03-10 14:45:46.123478166 +0200
@@ -20,6 +20,7 @@
#include <linux/serial_core.h>
#include <linux/interrupt.h>
#include <linux/io.h>
+#include <linux/dmi.h>
#include <linux/dmaengine.h>
#include <linux/pch_dma.h>
@@ -1403,14 +1404,18 @@
if (!rxbuf)
goto init_port_free_txbuf;
+ base_baud = 1843200; /* 1.8432MHz */
+
+ /* quirk for CM-iTC board */
+ if (strstr(dmi_get_system_info(DMI_BOARD_NAME), "CM-iTC"))
+ base_baud = 192000000; /* 192.0MHz */
+
switch (port_type) {
case PORT_UNKNOWN:
fifosize = 256; /* EG20T/ML7213: UART0 */
- base_baud = 1843200; /* 1.8432MHz */
break;
case PORT_8250:
fifosize = 64; /* EG20T:UART1~3 ML7213: UART1~2*/
- base_baud = 1843200; /* 1.8432MHz */
break;
default:
dev_err(&pdev->dev, "Invalid Port Type(=%d)\n", port_type);
^ permalink raw reply [flat|nested] 8+ messages in thread* Re: [PATCH v3] pch_uart: reference clock on CM-iTC
2011-03-10 13:14 ` [PATCH v3] " Denis Turischev
@ 2011-03-11 22:25 ` Greg KH
2011-03-13 13:48 ` Denis Turischev
0 siblings, 1 reply; 8+ messages in thread
From: Greg KH @ 2011-03-11 22:25 UTC (permalink / raw)
To: Denis Turischev; +Cc: Greg Kroah-Hartman, linux-kernel, Tomoya MORINAGA
On Thu, Mar 10, 2011 at 03:14:00PM +0200, Denis Turischev wrote:
> Default clock source for UARTs on Topcliff is external UART_CLK.
> On CM-iTC USB_48MHz is used instead. After VCO2PLL and DIV
> manipulations UARTs will receive 192 MHz.
> Clock manipulations on Topcliff are controlled in pch_phub.c
>
> v2: redone against the linux-next tree
> v3: redone against linux/kernel/git/next/linux-next.git snapshot
>
> Signed-off-by: Denis Turischev <denis@compulab.co.il>
> ---
> diff -Nru linux-next-20110310.orig/drivers/misc/pch_phub.c linux-next-20110310/drivers/misc/pch_phub.c
> --- linux-next-20110310.orig/drivers/misc/pch_phub.c 2011-03-10 08:31:30.000000000 +0200
> +++ linux-next-20110310/drivers/misc/pch_phub.c 2011-03-10 14:42:05.110978473 +0200
> @@ -618,6 +626,14 @@
> CLKCFG_CAN_50MHZ,
> CLKCFG_CANCLK_MASK);
>
> + /* quirk for CM-iTC board */
> + if (strstr(dmi_get_system_info(DMI_BOARD_NAME), "CM-iTC"))
> + pch_phub_read_modify_write_reg(chip,
> + (unsigned int)CLKCFG_REG_OFFSET,
> + CLKCFG_UART_48MHZ | CLKCFG_BAUDDIV |
> + CLKCFG_PLL2VCO | CLKCFG_UARTCLKSEL,
> + CLKCFG_UART_MASK);
> +
This is the chunk that is causing problems. I guess someone else
modified this file in the linux-next tree, and I can't apply it in mine.
Any ideas who did this change? Can you look at the linux-next tree and
see what caused this merge issue?
thanks,
greg k-h
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v3] pch_uart: reference clock on CM-iTC
2011-03-11 22:25 ` Greg KH
@ 2011-03-13 13:48 ` Denis Turischev
2011-03-14 23:25 ` Greg KH
0 siblings, 1 reply; 8+ messages in thread
From: Denis Turischev @ 2011-03-13 13:48 UTC (permalink / raw)
To: Greg KH; +Cc: Greg Kroah-Hartman, linux-kernel, Tomoya MORINAGA
Hi Greg,
There is a patch to pch_phub.c that is absent in your linux/kernel/git/gregkh/tty-2.6.git
pch_phub: add new device ML7213
http://git.kernel.org/?p=linux/kernel/git/next/linux-next.git;a=commit;h=c47dda7d179dde17697c3f839f150fecaf6770cb
>From which repository you want my patch to be based?
On 03/12/2011 12:25 AM, Greg KH wrote:
> On Thu, Mar 10, 2011 at 03:14:00PM +0200, Denis Turischev wrote:
>> Default clock source for UARTs on Topcliff is external UART_CLK.
>> On CM-iTC USB_48MHz is used instead. After VCO2PLL and DIV
>> manipulations UARTs will receive 192 MHz.
>> Clock manipulations on Topcliff are controlled in pch_phub.c
>>
>> v2: redone against the linux-next tree
>> v3: redone against linux/kernel/git/next/linux-next.git snapshot
>>
>> Signed-off-by: Denis Turischev <denis@compulab.co.il>
>> ---
>> diff -Nru linux-next-20110310.orig/drivers/misc/pch_phub.c linux-next-20110310/drivers/misc/pch_phub.c
>> --- linux-next-20110310.orig/drivers/misc/pch_phub.c 2011-03-10 08:31:30.000000000 +0200
>> +++ linux-next-20110310/drivers/misc/pch_phub.c 2011-03-10 14:42:05.110978473 +0200
>> @@ -618,6 +626,14 @@
>> CLKCFG_CAN_50MHZ,
>> CLKCFG_CANCLK_MASK);
>>
>> + /* quirk for CM-iTC board */
>> + if (strstr(dmi_get_system_info(DMI_BOARD_NAME), "CM-iTC"))
>> + pch_phub_read_modify_write_reg(chip,
>> + (unsigned int)CLKCFG_REG_OFFSET,
>> + CLKCFG_UART_48MHZ | CLKCFG_BAUDDIV |
>> + CLKCFG_PLL2VCO | CLKCFG_UARTCLKSEL,
>> + CLKCFG_UART_MASK);
>> +
>
> This is the chunk that is causing problems. I guess someone else
> modified this file in the linux-next tree, and I can't apply it in mine.
> Any ideas who did this change? Can you look at the linux-next tree and
> see what caused this merge issue?
>
> thanks,
>
> greg k-h
--
Denis
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v3] pch_uart: reference clock on CM-iTC
2011-03-13 13:48 ` Denis Turischev
@ 2011-03-14 23:25 ` Greg KH
0 siblings, 0 replies; 8+ messages in thread
From: Greg KH @ 2011-03-14 23:25 UTC (permalink / raw)
To: Denis Turischev; +Cc: Greg Kroah-Hartman, linux-kernel, Tomoya MORINAGA
On Sun, Mar 13, 2011 at 03:48:00PM +0200, Denis Turischev wrote:
> Hi Greg,
>
> There is a patch to pch_phub.c that is absent in your linux/kernel/git/gregkh/tty-2.6.git
> pch_phub: add new device ML7213
> http://git.kernel.org/?p=linux/kernel/git/next/linux-next.git;a=commit;h=c47dda7d179dde17697c3f839f150fecaf6770cb
>
> >From which repository you want my patch to be based?
Ok, sorry, that was from one of my other trees (the driver-core one).
I've now cherry picked that patch into my tty one and taken yours as
well.
Sorry for the mess, it was my fault.
greg k-h
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2011-03-14 23:47 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2011-03-07 9:31 pch_uart: reference clock on CM-iTC Denis Turischev
2011-03-07 20:07 ` Greg KH
2011-03-08 12:22 ` [PATCH v2] " Denis Turischev
2011-03-09 23:42 ` Greg KH
2011-03-10 13:14 ` [PATCH v3] " Denis Turischev
2011-03-11 22:25 ` Greg KH
2011-03-13 13:48 ` Denis Turischev
2011-03-14 23:25 ` Greg KH
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox