* [PROBLEM] ASUS Sandybridge motherboards + PCI not working (IRQ n: nobody cared)
@ 2011-10-14 11:04 Chris Palmer
2011-10-15 0:29 ` Robert Hancock
2011-10-15 16:51 ` Thomas Backlund
0 siblings, 2 replies; 7+ messages in thread
From: Chris Palmer @ 2011-10-14 11:04 UTC (permalink / raw)
To: linux-kernel
Interrupt handling for *PCI boards with ASUS Sandybridge motherboards*
seems to be broken.
It has been seen with network and non-network PCI boards. PCIx network
boards work OK. And all reports are for ASUS motherboards.
It always results in the infamous "IRQ n: nobody cared" message usually
within an hour. It is possible to restart things by rmmod/modprobe on
the appropriate PCI driver.
Andrew Morton kindly took a quick look and thinks it is most likely an
ACPI bug.
Configuration summary:
- ASUS P8H67-V/R3 Motherboard (others have problems with similar M/Bs)
- M/B BIOS 0804 (just updated to that - no change)
- Core i5/2500K
- Onboard ethernet (at11c driver - works)
- Additional PCIx Intel ethernet board (e1000e driver - works)
- Additional PCI Broadcom BCM5702X ethernet board (tg3 driver - fails)
[ Also fails with other PCI boards such as RTL8139 ]
- Kernel 3.0.6
Any help much appreciated...
Previous references:
https://lkml.org/lkml/2011/6/30/197
https://bugzilla.kernel.org/show_bug.cgi?id=38632
https://bugzilla.redhat.com/show_bug.cgi?id=713351
https://bugzilla.kernel.org/show_bug.cgi?id=35332
https://bugzilla.kernel.org/show_bug.cgi?id=34242
https://bugzilla.kernel.org/show_bug.cgi?id=32242
https://bugzilla.kernel.org/show_bug.cgi?id=39122
Chris
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PROBLEM] ASUS Sandybridge motherboards + PCI not working (IRQ n: nobody cared)
2011-10-14 11:04 [PROBLEM] ASUS Sandybridge motherboards + PCI not working (IRQ n: nobody cared) Chris Palmer
@ 2011-10-15 0:29 ` Robert Hancock
2011-10-15 8:43 ` Chris Palmer
2011-10-15 16:51 ` Thomas Backlund
1 sibling, 1 reply; 7+ messages in thread
From: Robert Hancock @ 2011-10-15 0:29 UTC (permalink / raw)
To: Chris Palmer; +Cc: linux-kernel
On 10/14/2011 05:04 AM, Chris Palmer wrote:
> Interrupt handling for *PCI boards with ASUS Sandybridge motherboards*
> seems to be broken.
>
> It has been seen with network and non-network PCI boards. PCIx network
> boards work OK. And all reports are for ASUS motherboards.
>
> It always results in the infamous "IRQ n: nobody cared" message usually
> within an hour. It is possible to restart things by rmmod/modprobe on
> the appropriate PCI driver.
>
> Andrew Morton kindly took a quick look and thinks it is most likely an
> ACPI bug.
>
> Configuration summary:
> - ASUS P8H67-V/R3 Motherboard (others have problems with similar M/Bs)
> - M/B BIOS 0804 (just updated to that - no change)
> - Core i5/2500K
> - Onboard ethernet (at11c driver - works)
> - Additional PCIx Intel ethernet board (e1000e driver - works)
> - Additional PCI Broadcom BCM5702X ethernet board (tg3 driver - fails)
> [ Also fails with other PCI boards such as RTL8139 ]
> - Kernel 3.0.6
>
>
> Any help much appreciated...
>
> Previous references:
>
> https://lkml.org/lkml/2011/6/30/197
> https://bugzilla.kernel.org/show_bug.cgi?id=38632
> https://bugzilla.redhat.com/show_bug.cgi?id=713351
> https://bugzilla.kernel.org/show_bug.cgi?id=35332
> https://bugzilla.kernel.org/show_bug.cgi?id=34242
> https://bugzilla.kernel.org/show_bug.cgi?id=32242
> https://bugzilla.kernel.org/show_bug.cgi?id=39122
The bugzilla reports aren't currently accessible so I don't know if it
was posted there, but can you post the output of "lspci -vv" as root?
Could be that some other device is configured on that IRQ and sometimes
spuriously generates interrupts.
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PROBLEM] ASUS Sandybridge motherboards + PCI not working (IRQ n: nobody cared)
2011-10-15 0:29 ` Robert Hancock
@ 2011-10-15 8:43 ` Chris Palmer
2011-10-15 16:23 ` Robert Hancock
0 siblings, 1 reply; 7+ messages in thread
From: Chris Palmer @ 2011-10-15 8:43 UTC (permalink / raw)
To: Robert Hancock; +Cc: linux-kernel
On 15/10/2011 01:29, Robert Hancock wrote:
> On 10/14/2011 05:04 AM, Chris Palmer wrote:
>> Interrupt handling for *PCI boards with ASUS Sandybridge motherboards*
>> seems to be broken.
>>
>> It has been seen with network and non-network PCI boards. PCIx network
>> boards work OK. And all reports are for ASUS motherboards.
>>
>> It always results in the infamous "IRQ n: nobody cared" message usually
>> within an hour. It is possible to restart things by rmmod/modprobe on
>> the appropriate PCI driver.
>>
>> Andrew Morton kindly took a quick look and thinks it is most likely an
>> ACPI bug.
>>
>> Configuration summary:
>> - ASUS P8H67-V/R3 Motherboard (others have problems with similar M/Bs)
>> - M/B BIOS 0804 (just updated to that - no change)
>> - Core i5/2500K
>> - Onboard ethernet (at11c driver - works)
>> - Additional PCIx Intel ethernet board (e1000e driver - works)
>> - Additional PCI Broadcom BCM5702X ethernet board (tg3 driver - fails)
>> [ Also fails with other PCI boards such as RTL8139 ]
>> - Kernel 3.0.6
>>
>>
>> Any help much appreciated...
>>
>> Previous references:
>>
>> https://lkml.org/lkml/2011/6/30/197
>> https://bugzilla.kernel.org/show_bug.cgi?id=38632
>> https://bugzilla.redhat.com/show_bug.cgi?id=713351
>> https://bugzilla.kernel.org/show_bug.cgi?id=35332
>> https://bugzilla.kernel.org/show_bug.cgi?id=34242
>> https://bugzilla.kernel.org/show_bug.cgi?id=32242
>> https://bugzilla.kernel.org/show_bug.cgi?id=39122
>
> The bugzilla reports aren't currently accessible so I don't know if it
> was posted there, but can you post the output of "lspci -vv" as root?
> Could be that some other device is configured on that IRQ and
> sometimes spuriously generates interrupts.
>
Robert
Various outputs below.
Many thanks
Chris
--------------------------------------------------------------------------------------------------------------------
/var/adm/messages at point of failure
Oct 13 22:12:43 woody1 kernel: [ 9958.088517] irq 16: nobody cared (try
booting with the "irqpoll" option)
Oct 13 22:12:43 woody1 kernel: [ 9958.088523] Pid: 0, comm: kworker/0:0
Not tainted 3.0.6 #1
Oct 13 22:12:43 woody1 kernel: [ 9958.088526] Call Trace:
Oct 13 22:12:43 woody1 kernel: [ 9958.088528] <IRQ>
[<ffffffff81082db7>] __report_bad_irq+0x37/0xc3
Oct 13 22:12:43 woody1 kernel: [ 9958.088540] [<ffffffff8108317b>]
note_interrupt+0x151/0x1ca
Oct 13 22:12:43 woody1 kernel: [ 9958.088545] [<ffffffff810817ed>]
handle_irq_event_percpu+0x179/0x197
Oct 13 22:12:43 woody1 kernel: [ 9958.088549] [<ffffffff8108183c>]
handle_irq_event+0x31/0x4d
Oct 13 22:12:43 woody1 kernel: [ 9958.088554] [<ffffffff81067467>] ?
arch_local_irq_save+0x18/0x1e
Oct 13 22:12:43 woody1 kernel: [ 9958.088558] [<ffffffff81083919>]
handle_fasteoi_irq+0x77/0x98
Oct 13 22:12:43 woody1 kernel: [ 9958.088562] [<ffffffff810042ed>]
handle_irq+0x88/0x90
Oct 13 22:12:43 woody1 kernel: [ 9958.088567] [<ffffffff813d25fd>]
do_IRQ+0x4d/0xa5
Oct 13 22:12:43 woody1 kernel: [ 9958.088571] [<ffffffff813d07d3>]
common_interrupt+0x13/0x13
Oct 13 22:12:43 woody1 kernel: [ 9958.088573] <EOI>
[<ffffffff81008809>] ? paravirt_read_tsc+0x9/0xd
Oct 13 22:12:43 woody1 kernel: [ 9958.088581] [<ffffffff8121a577>] ?
intel_idle+0xd1/0xf8
Oct 13 22:12:43 woody1 kernel: [ 9958.088585] [<ffffffff8121a559>] ?
intel_idle+0xb3/0xf8
Oct 13 22:12:43 woody1 kernel: [ 9958.088590] [<ffffffff813066ff>]
cpuidle_idle_call+0xa1/0xe9
Oct 13 22:12:43 woody1 kernel: [ 9958.088595] [<ffffffff8100130b>]
cpu_idle+0xaa/0xcc
Oct 13 22:12:43 woody1 kernel: [ 9958.088600] [<ffffffff813cad33>]
start_secondary+0x248/0x24f
Oct 13 22:12:43 woody1 kernel: [ 9958.088603] handlers:
Oct 13 22:12:43 woody1 kernel: [ 9958.088614] [<ffffffffa0060919>]
tg3_interrupt_tagged
Oct 13 22:12:43 woody1 kernel: [ 9958.088617] Disabling IRQ #16
--------------------------------------------------------------------------------------------------------------
cat /proc/interrupts
CPU0 CPU1 CPU2 CPU3
0: 582 0 0 0 IO-APIC-edge timer
1: 4 0 0 0 IO-APIC-edge i8042
4: 1764360 147833 0 0 IO-APIC-edge serial
8: 1 0 0 0 IO-APIC-edge rtc0
9: 0 0 0 0 IO-APIC-fasteoi acpi
12: 5 0 0 0 IO-APIC-edge i8042
16: 28 299982 0 0 IO-APIC-fasteoi eth2
23: 57444 9 0 0 IO-APIC-fasteoi
ehci_hcd:usb3, ehci_hcd:usb4
40: 0 0 0 0 PCI-MSI-edge
PCIe PME
41: 0 0 0 0 PCI-MSI-edge
PCIe PME
42: 0 0 0 0 PCI-MSI-edge
PCIe PME
43: 0 0 0 0 PCI-MSI-edge
PCIe PME
44: 0 0 0 0 PCI-MSI-edge
PCIe PME
45: 0 0 0 0 PCI-MSI-edge
PCIe PME
46: 0 0 0 0 PCI-MSI-edge
PCIe PME
47: 2538605 0 0 0 PCI-MSI-edge ahci
48: 0 0 0 0 PCI-MSI-edge
xhci_hcd
49: 0 0 0 0 PCI-MSI-edge
xhci_hcd
50: 0 0 0 0 PCI-MSI-edge
xhci_hcd
51: 0 0 0 0 PCI-MSI-edge
xhci_hcd
52: 0 0 0 0 PCI-MSI-edge
xhci_hcd
53: 342497 0 0 0 PCI-MSI-edge
eth0-rx-0
54: 209063 0 0 0 PCI-MSI-edge
eth0-tx-0
55: 2 0 0 0 PCI-MSI-edge eth0
56: 7095 0 1839 0 PCI-MSI-edge radeon
57: 1850698 0 0 0 PCI-MSI-edge eth1
NMI: 0 0 0 0 Non-maskable interrupts
LOC: 21319335 24311389 13606677 6465693 Local timer interrupts
SPU: 0 0 0 0 Spurious interrupts
PMI: 0 0 0 0 Performance
monitoring interrupts
IWI: 0 0 0 0 IRQ work interrupts
RES: 1550702 2765775 1892119 902441 Rescheduling interrupts
CAL: 108068 117537 59700 44941 Function call interrupts
TLB: 70131 66583 70222 69524 TLB shootdowns
TRM: 0 0 0 0 Thermal event interrupts
THR: 0 0 0 0 Threshold APIC interrupts
MCE: 0 0 0 0 Machine check exceptions
MCP: 457 457 457 457 Machine check polls
ERR: 0
MIS: 0
--------------------------------------------------------------------------------------------------------------------
lspci -vv
00:00.0 Host bridge: Intel Corporation Sandy Bridge DRAM Controller (rev 09)
Subsystem: ASUSTeK Computer Inc. Device 844d
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>
00:01.0 PCI bridge: Intel Corporation Sandy Bridge PCI Express Root Port
(rev 09) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fe600000-fe6fffff
Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [88] Subsystem: ASUSTeK Computer Inc. Device 844d
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 4159
Capabilities: [a0] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #2, Speed 5GT/s, Width x16, ASPM unknown,
Latency L0 <256ns, L1 <4us
ClockPM- Surprise- LLActRep- BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+
DLActive- BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surprise-
Slot #0, PowerLimit 75.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt-
HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal-
PMEIntEna+ CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-
ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance-
SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128-
WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [140 v1] Root Complex Link
Desc: PortNumber=02 ComponentID=01 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=01
AssocRCRB- LinkType=MemMapped LinkValid+
Addr: 00000000fed19000
Kernel driver in use: pcieport
Kernel modules: shpchp
00:16.0 Communication controller: Intel Corporation Cougar Point HECI
Controller #1 (rev 04)
Subsystem: ASUSTeK Computer Inc. Device 844d
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fe708000 (64-bit, non-prefetchable) [size=16]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [8c] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
00:1a.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host
Controller #2 (rev 05) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device 844d
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at fe707000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1b.0 Audio device: Intel Corporation Cougar Point High Definition
Audio Controller (rev 05)
Subsystem: ASUSTeK Computer Inc. Device 841b
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 3
Region 0: Memory at fe700000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v1) Root Complex Integrated
Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag- RBE- FLReset+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown,
Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk-
DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128-
WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status: NegoPending- InProgress-
VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128-
WRR256-
Ctrl: Enable+ ID=1 ArbSelect=Fixed TC/VC=22
Status: NegoPending- InProgress-
Capabilities: [130 v1] Root Complex Link
Desc: PortNumber=0f ComponentID=00 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=00
AssocRCRB- LinkType=MemMapped LinkValid+
Addr: 00000000fed1c000
00:1c.0 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port
1 (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #1, Speed 5GT/s, Width x2, ASPM L0s L1,
Latency L0 <1us, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surprise-
Slot #0, PowerLimit 0.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt-
HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal-
PMEIntEna+ CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 4161
Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 844d
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.2 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port
3 (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fe500000-fe5fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #3, Speed 5GT/s, Width x1, ASPM L0s L1,
Latency L0 <512ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surprise-
Slot #2, PowerLimit 10.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt-
HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
PresDet+ Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal-
PMEIntEna+ CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance-
SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 4169
Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 844d
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.3 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port
4 (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #4, Speed 5GT/s, Width x1, ASPM L0s L1,
Latency L0 <1us, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surprise-
Slot #3, PowerLimit 10.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt-
HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal-
PMEIntEna+ CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 4171
Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 844d
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.4 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port
5 (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fe400000-fe4fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #5, Speed 5GT/s, Width x1, ASPM L0s L1,
Latency L0 <1us, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surprise-
Slot #4, PowerLimit 10.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt-
HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
PresDet+ Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal-
PMEIntEna+ CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance-
SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 4179
Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 844d
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.5 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port
6 (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
Memory behind bridge: fe300000-fe3fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #6, Speed 5GT/s, Width x1, ASPM L0s L1,
Latency L0 <512ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surprise-
Slot #5, PowerLimit 10.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt-
HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
PresDet+ Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal-
PMEIntEna+ CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance-
SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 4181
Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 844d
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.6 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port
7 (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: fe200000-fe2fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #7, Speed 5GT/s, Width x1, ASPM L0s L1,
Latency L0 <512ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surprise-
Slot #6, PowerLimit 10.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt-
HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
PresDet+ Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal-
PMEIntEna+ CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance-
SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 4189
Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 844d
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.7 PCI bridge: Intel Corporation 82801 PCI Bridge (rev b5) (prog-if
01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=08, subordinate=09, sec-latency=0
Memory behind bridge: fe100000-fe1fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #8, Speed 5GT/s, Width x1, ASPM L0s L1,
Latency L0 <1us, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surprise-
Slot #7, PowerLimit 10.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt-
HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
PresDet+ Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal-
PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB
Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: 00000000 Data: 0000
Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 844d
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
00:1d.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host
Controller #1 (rev 05) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device 844d
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at fe706000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1f.0 ISA bridge: Intel Corporation Cougar Point LPC Controller (rev 05)
Subsystem: ASUSTeK Computer Inc. Device 844d
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>
00:1f.2 SATA controller: Intel Corporation Cougar Point 6 port SATA AHCI
Controller (rev 05) (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. Device 844d
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 47
Region 0: I/O ports at f070 [size=8]
Region 1: I/O ports at f060 [size=4]
Region 2: I/O ports at f050 [size=8]
Region 3: I/O ports at f040 [size=4]
Region 4: I/O ports at f020 [size=32]
Region 5: Memory at fe705000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0100c Data: 4199
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
Capabilities: [b0] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ahci
00:1f.3 SMBus: Intel Corporation Cougar Point SMBus Controller (rev 05)
Subsystem: ASUSTeK Computer Inc. Device 844d
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fe704000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at f000 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
01:00.0 VGA compatible controller: ATI Technologies Inc RV530LE [Radeon
X1600/X1650 PRO] (prog-if 00 [VGA controller])
Subsystem: PC Partner Limited Device 0880
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 56
Region 0: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 2: Memory at fe630000 (64-bit, non-prefetchable) [size=64K]
Region 4: I/O ports at e000 [size=256]
Expansion ROM at fe600000 [disabled] [size=128K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<4us, L1 unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1,
Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0400c Data: 4122
Kernel driver in use: radeon
Kernel modules: radeon
01:00.1 Display controller: ATI Technologies Inc RV530LE [Radeon X1650
PRO] (Secondary)
Subsystem: PC Partner Limited Device 0881
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Region 0: Memory at fe620000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<4us, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1,
Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
03:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network
Connection
Subsystem: Intel Corporation Gigabit CT Desktop Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fe5c0000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at fe500000 (32-bit, non-prefetchable) [size=512K]
Region 2: I/O ports at d000 [size=32]
Region 3: Memory at fe5e0000 (32-bit, non-prefetchable) [size=16K]
Expansion ROM at fe580000 [disabled] [size=256K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s
<512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1,
Latency L0 <128ns, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [a0] MSI-X: Enable+ Count=5 Masked-
Vector table: BAR=3 offset=00000000
PBA: BAR=3 offset=00002000
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt-
UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap-
ChkEn-
Capabilities: [140 v1] Device Serial Number 00-1b-21-ff-ff-ad-77-d1
Kernel driver in use: e1000e
Kernel modules: e1000e
05:00.0 IDE interface: VIA Technologies, Inc. PATA IDE Host Controller
(prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. Device 838f
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at c040 [size=8]
Region 1: I/O ports at c030 [size=4]
Region 2: I/O ports at c020 [size=8]
Region 3: I/O ports at c010 [size=4]
Region 4: I/O ports at c000 [size=16]
Expansion ROM at fe400000 [disabled] [size=64K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] MSI: Enable- Count=1/1 Maskable+ 64bit+
Address: 0000000000000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [90] Express (v1) Legacy Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1,
Latency L0 <1us, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk-
DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt-
UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr+
AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+
ChkEn-
Capabilities: [130 v1] Device Serial Number 00-40-63-ff-ff-63-40-00
Kernel modules: ata_generic
06:00.0 USB Controller: Device 1b21:1042 (prog-if 30)
Subsystem: ASUSTeK Computer Inc. Device 8488
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fe300000 (64-bit, non-prefetchable) [size=32K]
Capabilities: [50] MSI: Enable- Count=1/8 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [68] MSI-X: Enable+ Count=8 Masked-
Vector table: BAR=0 offset=00002000
PBA: BAR=0 offset=00002080
Capabilities: [78] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Express (v2) Legacy Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <2us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1,
Latency L0 <512ns, L1 <2us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance-
SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128-
WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status: NegoPending- InProgress-
Kernel driver in use: xhci_hcd
Kernel modules: xhci-hcd
07:00.0 Ethernet controller: Atheros Communications Device 1083 (rev c0)
Subsystem: ASUSTeK Computer Inc. Device 847e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 57
Region 0: Memory at fe200000 (64-bit, non-prefetchable) [size=256K]
Region 2: I/O ports at b000 [size=128]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0100c Data: 412a
Capabilities: [58] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 4096 bytes, PhantFunc 0, Latency L0s
unlimited, L1 unlimited
ExtTag- AttnBtn+ AttnInd+ PwrInd+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1,
Latency L0 unlimited, L1 unlimited
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [6c] Vital Product Data
pcilib: sysfs_read_vpd: read failed: Connection timed out
Not readable
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP- SDES+ TLP- FCP- CmpltTO- CmpltAbrt-
UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr+
AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+
ChkEn-
Capabilities: [180 v1] Device Serial Number ff-e4-fa-01-bc-ae-c5-ff
Kernel driver in use: atl1c
Kernel modules: atl1c
08:00.0 PCI bridge: Device 1b21:1080 (rev 01) (prog-if 01 [Subtractive
decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=08, secondary=09, subordinate=09, sec-latency=32
Memory behind bridge: fe100000-fe1fffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [c0] Subsystem: ASUSTeK Computer Inc. Device 8489
09:01.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5702X
Gigabit Ethernet (rev 02)
Subsystem: 3Com Corporation Device 1100
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (16000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fe100000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [40] PCI-X non-bridge device
Command: DPERE- ERO+ RBC=512 OST=1
Status: Dev=ff:1f.1 64bit+ 133MHz+ SCD- USC- DC=simple
DMMRBC=2048 DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz-
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Product Name: 3Com 10/100/1000 PCI
Read-only fields:
[PN] Part number: 3C1000B-T
[EC] Engineering changes: 109904-40
[SN] Serial number: HYFR00386E
[MN] Manufacture ID: 31 30 42 37
[V0] Vendor specific: N/A
[RV] Reserved: checksum bad, 47 byte(s) reserved
Read/write fields:
[YA] Asset tag: XYZ01234567
[V1] Vendor specific: N/A
[RW] Read-write area: 101 byte(s) free
End
Capabilities: [58] MSI: Enable- Count=1/8 Maskable- 64bit+
Address: efbfdbeebfefebfc Data: fbfd
Kernel driver in use: tg3
Kernel modules: tg3
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
/var/adm/messages during boot
Oct 13 19:27:05 woody1 kernel: [ 0.539846] ACPI: Executed 1 blocks of
module-level executable AML code
Oct 13 19:27:05 woody1 kernel: [ 0.542050] ACPI Error: [RAMB]
Namespace lookup failure, AE_NOT_FOUND (20110413/psargs-359)
Oct 13 19:27:05 woody1 kernel: [ 0.542401] ACPI Exception:
AE_NOT_FOUND, Could not execute arguments for [RAMW] (Region)
(20110413/nsinit-349)
Oct 13 19:27:05 woody1 kernel: [ 0.542885] ACPI: SSDT
00000000cf5ddc18 0038C (v01 AMI IST 00000001 MSFT 03000001)
Oct 13 19:27:05 woody1 kernel: [ 0.543445] ACPI: Dynamic OEM Table Load:
Oct 13 19:27:05 woody1 kernel: [ 0.543674] ACPI: SSDT
(null) 0038C (v01 AMI IST 00000001 MSFT 03000001)
Oct 13 19:27:05 woody1 kernel: [ 0.543990] ACPI: SSDT
00000000cf5dee18 00084 (v01 AMI CST 00000001 MSFT 03000001)
Oct 13 19:27:05 woody1 kernel: [ 0.544505] ACPI: Dynamic OEM Table Load:
Oct 13 19:27:05 woody1 kernel: [ 0.544730] ACPI: SSDT
(null) 00084 (v01 AMI CST 00000001 MSFT 03000001)
Oct 13 19:27:05 woody1 kernel: [ 0.545425] ACPI: Interpreter enabled
Oct 13 19:27:05 woody1 kernel: [ 0.545552] ACPI: (supports S0 S1 S3 S5)
Oct 13 19:27:05 woody1 kernel: [ 0.545888] ACPI: Using IOAPIC for
interrupt routing
Oct 13 19:27:05 woody1 kernel: [ 0.546032] PCI: MMCONFIG for domain
0000 [bus 00-3f] at [mem 0xe0000000-0xe3ffffff] (base 0xe0000000)
Oct 13 19:27:05 woody1 kernel: [ 0.546278] PCI: MMCONFIG at [mem
0xe0000000-0xe3ffffff] reserved in ACPI motherboard resources
Oct 13 19:27:05 woody1 kernel: [ 0.551242] [Firmware Bug]: ACPI: BIOS
_OSI(Linux) query ignored
Oct 13 19:27:05 woody1 kernel: [ 0.555191] PCI: Using host bridge
windows from ACPI; if necessary, use "pci=nocrs" and report a bug
Oct 13 19:27:05 woody1 kernel: [ 0.555540] ACPI: PCI Root Bridge
[PCI0] (domain 0000 [bus 00-ff])
Oct 13 19:27:05 woody1 kernel: [ 0.555825] pci_root PNP0A08:00: host
bridge window [io 0x0000-0x0cf7]
Oct 13 19:27:05 woody1 kernel: [ 0.555955] pci_root PNP0A08:00: host
bridge window [io 0x0d00-0xffff]
Oct 13 19:27:05 woody1 kernel: [ 0.556084] pci_root PNP0A08:00: host
bridge window [mem 0x000a0000-0x000bffff]
Oct 13 19:27:05 woody1 kernel: [ 0.556291] pci_root PNP0A08:00: host
bridge window [mem 0x000c8000-0x000dffff]
Oct 13 19:27:05 woody1 kernel: [ 0.556496] pci_root PNP0A08:00: host
bridge window [mem 0xd0000000-0xffffffff]
Oct 13 19:27:05 woody1 kernel: [ 0.556706] pci_root PNP0A08:00:
address space collision: host bridge window [mem 0x000c8000-0x000dffff]
conflicts with Video ROM [mem 0x000c0000-0x000cf5ff]
Oct 13 19:27:05 woody1 kernel: [ 0.558418] pci 0000:01:00.0:
disabling ASPM on pre-1.1 PCIe device. You can enable it with
'pcie_aspm=force'
Oct 13 19:27:05 woody1 kernel: [ 0.558632] pci 0000:00:01.0: PCI
bridge to [bus 01-01]
Oct 13 19:27:05 woody1 kernel: [ 0.558809] pci 0000:00:1c.0: PCI
bridge to [bus 02-02]
Oct 13 19:27:05 woody1 kernel: [ 0.560679] pci 0000:00:1c.2: PCI
bridge to [bus 03-03]
Oct 13 19:27:05 woody1 kernel: [ 0.563592] pci 0000:00:1c.3: PCI
bridge to [bus 04-04]
Oct 13 19:27:05 woody1 kernel: [ 0.565670] pci 0000:00:1c.4: PCI
bridge to [bus 05-05]
Oct 13 19:27:05 woody1 kernel: [ 0.567669] pci 0000:00:1c.5: PCI
bridge to [bus 06-06]
Oct 13 19:27:05 woody1 kernel: [ 0.569669] pci 0000:00:1c.6: PCI
bridge to [bus 07-07]
Oct 13 19:27:05 woody1 kernel: [ 0.569983] pci 0000:00:1c.7: PCI
bridge to [bus 08-09] (subtractive decode)
Oct 13 19:27:05 woody1 kernel: [ 0.570470] pci 0000:08:00.0: PCI
bridge to [bus 09-09] (subtractive decode)
Oct 13 19:27:05 woody1 kernel: [ 0.571016] pci0000:00: Requesting
ACPI _OSC control (0x1d)
Oct 13 19:27:05 woody1 kernel: [ 0.571297] pci0000:00: ACPI _OSC
control (0x1c) granted
Oct 13 19:27:05 woody1 kernel: [ 0.574307] ACPI: PCI Interrupt Link
[LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
Oct 13 19:27:05 woody1 kernel: [ 0.575048] ACPI: PCI Interrupt Link
[LNKB] (IRQs 3 4 5 6 *7 10 11 12 14 15)
Oct 13 19:27:05 woody1 kernel: [ 0.575791] ACPI: PCI Interrupt Link
[LNKC] (IRQs 3 4 5 6 10 *11 12 14 15)
Oct 13 19:27:05 woody1 kernel: [ 0.576482] ACPI: PCI Interrupt Link
[LNKD] (IRQs 3 4 5 6 *10 11 12 14 15)
Oct 13 19:27:05 woody1 kernel: [ 0.577172] ACPI: PCI Interrupt Link
[LNKE] (IRQs 3 4 *5 6 7 10 11 12 14 15)
Oct 13 19:27:05 woody1 kernel: [ 0.577915] ACPI: PCI Interrupt Link
[LNKF] (IRQs 3 4 5 6 7 *10 11 12 14 15)
Oct 13 19:27:05 woody1 kernel: [ 0.578649] ACPI: PCI Interrupt Link
[LNKG] (IRQs *3 4 5 6 7 10 11 12 14 15)
Oct 13 19:27:05 woody1 kernel: [ 0.579386] ACPI: PCI Interrupt Link
[LNKH] (IRQs 3 4 *5 6 7 10 11 12 14 15)
Oct 13 19:27:05 woody1 kernel: [ 0.580148] vgaarb: device added:
PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
Oct 13 19:27:05 woody1 kernel: [ 0.580357] vgaarb: loaded
Oct 13 19:27:05 woody1 kernel: [ 0.580484] vgaarb: bridge control
possible 0000:01:00.0
Oct 13 19:27:05 woody1 kernel: [ 0.580658] SCSI subsystem initialized
Oct 13 19:27:05 woody1 kernel: [ 0.580833] usbcore: registered new
interface driver usbfs
Oct 13 19:27:05 woody1 kernel: [ 0.580969] usbcore: registered new
interface driver hub
Oct 13 19:27:05 woody1 kernel: [ 0.581110] usbcore: registered new
device driver usb
Oct 13 19:27:05 woody1 kernel: [ 0.581270] PCI: Using ACPI for IRQ
routing
Oct 13 19:27:05 woody1 kernel: [ 0.582873] NetLabel: Initializing
Oct 13 19:27:05 woody1 kernel: [ 0.583000] NetLabel: domain hash
size = 128
Oct 13 19:27:05 woody1 kernel: [ 0.583128] NetLabel: protocols =
UNLABELED CIPSOv4
Oct 13 19:27:05 woody1 kernel: [ 0.583262] NetLabel: unlabeled
traffic allowed by default
Oct 13 19:27:05 woody1 kernel: [ 0.583397] hpet0: at MMIO 0xfed00000,
IRQs 2, 8, 0, 0, 0, 0, 0, 0
Oct 13 19:27:05 woody1 kernel: [ 0.583962] hpet0: 8 comparators,
64-bit 14.318180 MHz counter
Oct 13 19:27:05 woody1 kernel: [ 0.587103] Switching to clocksource hpet
Oct 13 19:27:05 woody1 kernel: [ 0.587638] Switched to NOHz mode on
CPU #0
Oct 13 19:27:05 woody1 kernel: [ 0.587722] Switched to NOHz mode on
CPU #1
Oct 13 19:27:05 woody1 kernel: [ 0.587753] Switched to NOHz mode on
CPU #3
Oct 13 19:27:05 woody1 kernel: [ 0.587764] Switched to NOHz mode on
CPU #2
Oct 13 19:27:05 woody1 kernel: [ 0.590969] pnp: PnP ACPI init
Oct 13 19:27:05 woody1 kernel: [ 0.591107] ACPI: bus type pnp registered
Oct 13 19:27:05 woody1 kernel: [ 0.591467] system 00:01: [mem
0xfed10000-0xfed19fff] has been reserved
Oct 13 19:27:05 woody1 kernel: [ 0.591597] system 00:01: [mem
0xe0000000-0xe3ffffff] has been reserved
Oct 13 19:27:05 woody1 kernel: [ 0.591725] system 00:01: [mem
0xfed90000-0xfed93fff] has been reserved
Oct 13 19:27:05 woody1 kernel: [ 0.591853] system 00:01: [mem
0xfed20000-0xfed3ffff] has been reserved
Oct 13 19:27:05 woody1 kernel: [ 0.591982] system 00:01: [mem
0xfee00000-0xfee0ffff] has been reserved
Oct 13 19:27:05 woody1 kernel: [ 0.592183] system 00:02: [io
0x0290-0x029f] has been reserved
Oct 13 19:27:05 woody1 kernel: [ 0.592540] system 00:06: [io
0x04d0-0x04d1] has been reserved
Oct 13 19:27:05 woody1 kernel: [ 0.593056] system 00:09: [io
0x0400-0x0453] has been reserved
Oct 13 19:27:05 woody1 kernel: [ 0.593186] system 00:09: [io
0x0458-0x047f] has been reserved
Oct 13 19:27:05 woody1 kernel: [ 0.593321] system 00:09: [io
0x0500-0x057f] has been reserved
Oct 13 19:27:05 woody1 kernel: [ 0.593451] system 00:09: [mem
0xfed1c000-0xfed1ffff] has been reserved
Oct 13 19:27:05 woody1 kernel: [ 0.593580] system 00:09: [mem
0xfec00000-0xfecfffff] could not be reserved
Oct 13 19:27:05 woody1 kernel: [ 0.593709] system 00:09: [mem
0xfed08000-0xfed08fff] has been reserved
Oct 13 19:27:05 woody1 kernel: [ 0.593837] system 00:09: [mem
0xff000000-0xffffffff] has been reserved
Oct 13 19:27:05 woody1 kernel: [ 0.594016] system 00:0a: [io
0x0454-0x0457] has been reserved
Oct 13 19:27:05 woody1 kernel: [ 0.594378] pnp: PnP ACPI: found 12
devices
Oct 13 19:27:05 woody1 kernel: [ 0.594505] ACPI: ACPI bus type pnp
unregistered
Oct 13 19:27:05 woody1 kernel: [ 0.600096] pci 0000:00:01.0: PCI
bridge to [bus 01-01]
Oct 13 19:27:05 woody1 kernel: [ 0.600225] pci 0000:00:01.0: bridge
window [io 0xe000-0xefff]
Oct 13 19:27:05 woody1 kernel: [ 0.600359] pci 0000:00:01.0: bridge
window [mem 0xfe600000-0xfe6fffff]
Oct 13 19:27:05 woody1 kernel: [ 0.600490] pci 0000:00:01.0: bridge
window [mem 0xd0000000-0xdfffffff 64bit pref]
Oct 13 19:27:05 woody1 kernel: [ 0.600696] pci 0000:00:1c.0: PCI
bridge to [bus 02-02]
Oct 13 19:27:05 woody1 kernel: [ 0.600824] pci 0000:00:1c.0: bridge
window [io disabled]
Oct 13 19:27:05 woody1 kernel: [ 0.600956] pci 0000:00:1c.0: bridge
window [mem disabled]
Oct 13 19:27:05 woody1 kernel: [ 0.601085] pci 0000:00:1c.0: bridge
window [mem pref disabled]
Oct 13 19:27:05 woody1 kernel: [ 0.601218] pci 0000:00:1c.2: PCI
bridge to [bus 03-03]
Oct 13 19:27:05 woody1 kernel: [ 0.601351] pci 0000:00:1c.2: bridge
window [io 0xd000-0xdfff]
Oct 13 19:27:05 woody1 kernel: [ 0.601484] pci 0000:00:1c.2: bridge
window [mem 0xfe500000-0xfe5fffff]
Oct 13 19:27:05 woody1 kernel: [ 0.601616] pci 0000:00:1c.2: bridge
window [mem pref disabled]
Oct 13 19:27:05 woody1 kernel: [ 0.601749] pci 0000:00:1c.3: PCI
bridge to [bus 04-04]
Oct 13 19:27:05 woody1 kernel: [ 0.601877] pci 0000:00:1c.3: bridge
window [io disabled]
Oct 13 19:27:05 woody1 kernel: [ 0.602009] pci 0000:00:1c.3: bridge
window [mem disabled]
Oct 13 19:27:05 woody1 kernel: [ 0.602139] pci 0000:00:1c.3: bridge
window [mem pref disabled]
Oct 13 19:27:05 woody1 kernel: [ 0.602271] pci 0000:00:1c.4: PCI
bridge to [bus 05-05]
Oct 13 19:27:05 woody1 kernel: [ 0.602404] pci 0000:00:1c.4: bridge
window [io 0xc000-0xcfff]
Oct 13 19:27:05 woody1 kernel: [ 0.602538] pci 0000:00:1c.4: bridge
window [mem 0xfe400000-0xfe4fffff]
Oct 13 19:27:05 woody1 kernel: [ 0.602669] pci 0000:00:1c.4: bridge
window [mem pref disabled]
Oct 13 19:27:05 woody1 kernel: [ 0.602802] pci 0000:00:1c.5: PCI
bridge to [bus 06-06]
Oct 13 19:27:05 woody1 kernel: [ 0.602928] pci 0000:00:1c.5: bridge
window [io disabled]
Oct 13 19:27:05 woody1 kernel: [ 0.603060] pci 0000:00:1c.5: bridge
window [mem 0xfe300000-0xfe3fffff]
Oct 13 19:27:05 woody1 kernel: [ 0.603191] pci 0000:00:1c.5: bridge
window [mem pref disabled]
Oct 13 19:27:05 woody1 kernel: [ 0.603329] pci 0000:00:1c.6: PCI
bridge to [bus 07-07]
Oct 13 19:27:05 woody1 kernel: [ 0.603458] pci 0000:00:1c.6: bridge
window [io 0xb000-0xbfff]
Oct 13 19:27:05 woody1 kernel: [ 0.603589] pci 0000:00:1c.6: bridge
window [mem 0xfe200000-0xfe2fffff]
Oct 13 19:27:05 woody1 kernel: [ 0.603719] pci 0000:00:1c.6: bridge
window [mem pref disabled]
Oct 13 19:27:05 woody1 kernel: [ 0.603852] pci 0000:08:00.0: PCI
bridge to [bus 09-09]
Oct 13 19:27:05 woody1 kernel: [ 0.603982] pci 0000:08:00.0: bridge
window [io disabled]
Oct 13 19:27:05 woody1 kernel: [ 0.604115] pci 0000:08:00.0: bridge
window [mem 0xfe100000-0xfe1fffff]
Oct 13 19:27:05 woody1 kernel: [ 0.604248] pci 0000:08:00.0: bridge
window [mem pref disabled]
Oct 13 19:27:05 woody1 kernel: [ 0.604388] pci 0000:00:1c.7: PCI
bridge to [bus 08-09]
Oct 13 19:27:05 woody1 kernel: [ 0.604515] pci 0000:00:1c.7: bridge
window [io disabled]
Oct 13 19:27:05 woody1 kernel: [ 0.604646] pci 0000:00:1c.7: bridge
window [mem 0xfe100000-0xfe1fffff]
Oct 13 19:27:05 woody1 kernel: [ 0.604778] pci 0000:00:1c.7: bridge
window [mem pref disabled]
Oct 13 19:27:05 woody1 kernel: [ 0.604919] pci 0000:00:01.0: PCI INT
A -> GSI 16 (level, low) -> IRQ 16
Oct 13 19:27:05 woody1 kernel: [ 0.605056] pci 0000:00:1c.0: PCI INT
A -> GSI 17 (level, low) -> IRQ 17
Oct 13 19:27:05 woody1 kernel: [ 0.605197] pci 0000:00:1c.2: PCI INT
C -> GSI 18 (level, low) -> IRQ 18
Oct 13 19:27:05 woody1 kernel: [ 0.605341] pci 0000:00:1c.3: PCI INT
D -> GSI 19 (level, low) -> IRQ 19
Oct 13 19:27:05 woody1 kernel: [ 0.605479] pci 0000:00:1c.4: PCI INT
A -> GSI 17 (level, low) -> IRQ 17
Oct 13 19:27:05 woody1 kernel: [ 0.605616] pci 0000:00:1c.5: PCI INT
B -> GSI 16 (level, low) -> IRQ 16
Oct 13 19:27:05 woody1 kernel: [ 0.605752] pci 0000:00:1c.6: PCI INT
C -> GSI 18 (level, low) -> IRQ 18
Oct 13 19:27:05 woody1 kernel: [ 0.605890] pci 0000:00:1c.7: PCI INT
D -> GSI 19 (level, low) -> IRQ 19
Oct 13 19:27:05 woody1 kernel: [ 0.606025] pci 0000:08:00.0: PCI INT
A -> GSI 17 (level, low) -> IRQ 17
Oct 13 19:27:05 woody1 kernel: [ 0.606216] NET: Registered protocol
family 2
Oct 13 19:27:05 woody1 kernel: [ 0.606567] IP route cache hash table
entries: 524288 (order: 10, 4194304 bytes)
Oct 13 19:27:05 woody1 kernel: [ 0.607419] TCP established hash table
entries: 524288 (order: 11, 8388608 bytes)
Oct 13 19:27:05 woody1 kernel: [ 0.608622] TCP bind hash table
entries: 65536 (order: 8, 1048576 bytes)
Oct 13 19:27:05 woody1 kernel: [ 0.608872] TCP: Hash tables
configured (established 524288 bind 65536)
Oct 13 19:27:05 woody1 kernel: [ 0.608999] TCP reno registered
Oct 13 19:27:05 woody1 kernel: [ 0.609141] UDP hash table entries:
8192 (order: 6, 262144 bytes)
Oct 13 19:27:05 woody1 kernel: [ 0.609324] UDP-Lite hash table
entries: 8192 (order: 6, 262144 bytes)
Oct 13 19:27:05 woody1 kernel: [ 0.609536] NET: Registered protocol
family 1
Oct 13 19:27:05 woody1 kernel: [ 0.856196] Trying to unpack rootfs
image as initramfs...
Oct 13 19:27:05 woody1 kernel: [ 0.926378] Freeing initrd memory:
5312k freed
Oct 13 19:27:05 woody1 kernel: [ 0.926968] PCI-DMA: Using software
bounce buffering for IO (SWIOTLB)
Oct 13 19:27:05 woody1 kernel: [ 0.927109] Placing 64MB software IO
TLB between ffff8800cb41b000 - ffff8800cf41b000
Oct 13 19:27:05 woody1 kernel: [ 0.927315] software IO TLB at phys
0xcb41b000 - 0xcf41b000
Oct 13 19:27:05 woody1 kernel: [ 0.927833] audit: initializing
netlink socket (disabled)
Oct 13 19:27:05 woody1 kernel: [ 0.927966] type=2000
audit(1318530397.755:1): initialized
Oct 13 19:27:05 woody1 kernel: [ 0.942596] HugeTLB registered 2 MB
page size, pre-allocated 0 pages
Oct 13 19:27:05 woody1 kernel: [ 0.972545] msgmni has been set to 32126
Oct 13 19:27:05 woody1 kernel: [ 0.972843] Block layer SCSI generic
(bsg) driver version 0.4 loaded (major 253)
Oct 13 19:27:05 woody1 kernel: [ 0.973065] io scheduler noop registered
Oct 13 19:27:05 woody1 kernel: [ 0.973194] io scheduler deadline
registered (default)
Oct 13 19:27:05 woody1 kernel: [ 0.973344] io scheduler cfq registered
Oct 13 19:27:05 woody1 kernel: [ 0.974175] pcieport 0000:00:01.0:
Signaling PME through PCIe PME interrupt
Oct 13 19:27:05 woody1 kernel: [ 0.974303] pci 0000:01:00.0:
Signaling PME through PCIe PME interrupt
Oct 13 19:27:05 woody1 kernel: [ 0.974432] pci 0000:01:00.1:
Signaling PME through PCIe PME interrupt
Oct 13 19:27:05 woody1 kernel: [ 0.974575] pcieport 0000:00:1c.0:
Signaling PME through PCIe PME interrupt
Oct 13 19:27:05 woody1 kernel: [ 0.974721] pcieport 0000:00:1c.2:
Signaling PME through PCIe PME interrupt
Oct 13 19:27:05 woody1 kernel: [ 0.974852] pci 0000:03:00.0:
Signaling PME through PCIe PME interrupt
Oct 13 19:27:05 woody1 kernel: [ 0.975011] pcieport 0000:00:1c.3:
Signaling PME through PCIe PME interrupt
Oct 13 19:27:05 woody1 kernel: [ 0.975156] pcieport 0000:00:1c.4:
Signaling PME through PCIe PME interrupt
Oct 13 19:27:05 woody1 kernel: [ 0.975285] pci 0000:05:00.0:
Signaling PME through PCIe PME interrupt
Oct 13 19:27:05 woody1 kernel: [ 0.975428] pcieport 0000:00:1c.5:
Signaling PME through PCIe PME interrupt
Oct 13 19:27:05 woody1 kernel: [ 0.975557] pci 0000:06:00.0:
Signaling PME through PCIe PME interrupt
Oct 13 19:27:05 woody1 kernel: [ 0.975700] pcieport 0000:00:1c.6:
Signaling PME through PCIe PME interrupt
Oct 13 19:27:05 woody1 kernel: [ 0.975833] pci 0000:07:00.0:
Signaling PME through PCIe PME interrupt
Oct 13 19:27:05 woody1 kernel: [ 0.975984] pci_hotplug: PCI Hot Plug
PCI Core version: 0.5
Oct 13 19:27:05 woody1 kernel: [ 0.976218] input: Power Button as
/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
Oct 13 19:27:05 woody1 kernel: [ 0.976426] ACPI: Power Button [PWRB]
Oct 13 19:27:05 woody1 kernel: [ 0.976581] input: Power Button as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
Oct 13 19:27:05 woody1 kernel: [ 0.976787] ACPI: Power Button [PWRF]
Oct 13 19:27:05 woody1 kernel: [ 0.978510] Serial: 8250/16550 driver,
4 ports, IRQ sharing disabled
Oct 13 19:27:05 woody1 kernel: [ 0.999177] serial8250: ttyS0 at I/O
0x3f8 (irq = 4) is a 16550A
Oct 13 19:27:05 woody1 kernel: [ 1.052653] 00:08: ttyS0 at I/O 0x3f8
(irq = 4) is a 16550A
Oct 13 19:27:05 woody1 kernel: [ 1.052983] Non-volatile memory driver
v1.3
Oct 13 19:27:05 woody1 kernel: [ 1.053735] brd: module loaded
Oct 13 19:27:05 woody1 kernel: [ 1.054163] loop: module loaded
Oct 13 19:27:05 woody1 kernel: [ 1.054334] ahci 0000:00:1f.2: PCI INT
B -> GSI 20 (level, low) -> IRQ 20
Oct 13 19:27:05 woody1 kernel: [ 1.064924] ahci 0000:00:1f.2: AHCI
0001.0300 32 slots 6 ports 6 Gbps 0x1c impl SATA mode
Oct 13 19:27:05 woody1 kernel: [ 1.065145] ahci 0000:00:1f.2: flags:
64bit ncq sntf pm led clo pio slum part ems apst
Oct 13 19:27:05 woody1 kernel: [ 1.069232] scsi0 : ahci
Oct 13 19:27:05 woody1 kernel: [ 1.069413] scsi1 : ahci
Oct 13 19:27:05 woody1 kernel: [ 1.069580] scsi2 : ahci
Oct 13 19:27:05 woody1 kernel: [ 1.069745] scsi3 : ahci
Oct 13 19:27:05 woody1 kernel: [ 1.069923] scsi4 : ahci
Oct 13 19:27:05 woody1 kernel: [ 1.070094] scsi5 : ahci
Oct 13 19:27:05 woody1 kernel: [ 1.070315] ata1: DUMMY
Oct 13 19:27:05 woody1 kernel: [ 1.070441] ata2: DUMMY
Oct 13 19:27:05 woody1 kernel: [ 1.070566] ata3: SATA max UDMA/133
abar m2048@0xfe705000 port 0xfe705200 irq 47
Oct 13 19:27:05 woody1 kernel: [ 1.070773] ata4: SATA max UDMA/133
abar m2048@0xfe705000 port 0xfe705280 irq 47
Oct 13 19:27:05 woody1 kernel: [ 1.070990] ata5: SATA max UDMA/133
abar m2048@0xfe705000 port 0xfe705300 irq 47
Oct 13 19:27:05 woody1 kernel: [ 1.071196] ata6: DUMMY
Oct 13 19:27:05 woody1 kernel: [ 1.071396] i8042: PNP: No PS/2
controller found. Probing ports directly.
Oct 13 19:27:05 woody1 kernel: [ 1.074175] serio: i8042 KBD port at
0x60,0x64 irq 1
Oct 13 19:27:05 woody1 kernel: [ 1.074306] serio: i8042 AUX port at
0x60,0x64 irq 12
Oct 13 19:27:05 woody1 kernel: [ 1.074454] mousedev: PS/2 mouse
device common for all mice
Oct 13 19:27:05 woody1 kernel: [ 1.074630] rtc_cmos 00:04: RTC can
wake from S4
Oct 13 19:27:05 woody1 kernel: [ 1.074834] rtc_cmos 00:04: rtc core:
registered rtc_cmos as rtc0
Oct 13 19:27:05 woody1 kernel: [ 1.074994] rtc0: alarms up to one
month, y3k, 114 bytes nvram, hpet irqs
Oct 13 19:27:05 woody1 kernel: [ 1.077847] md: raid1 personality
registered for level 1
Oct 13 19:27:05 woody1 kernel: [ 1.077982] md: raid6 personality
registered for level 6
Oct 13 19:27:05 woody1 kernel: [ 1.078111] md: raid5 personality
registered for level 5
Oct 13 19:27:05 woody1 kernel: [ 1.078240] md: raid4 personality
registered for level 4
Oct 13 19:27:05 woody1 kernel: [ 1.078404] device-mapper: uevent:
version 1.0.3
Oct 13 19:27:05 woody1 kernel: [ 1.078574] device-mapper: ioctl:
4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com
Oct 13 19:27:05 woody1 kernel: [ 1.078844] cpuidle: using governor ladder
Oct 13 19:27:05 woody1 kernel: [ 1.079085] cpuidle: using governor menu
Oct 13 19:27:05 woody1 kernel: [ 1.079213] EFI Variables Facility
v0.08 2004-May-17
Oct 13 19:27:05 woody1 kernel: [ 1.079409] usbcore: registered new
interface driver usbhid
Oct 13 19:27:05 woody1 kernel: [ 1.079537] usbhid: USB HID core driver
Oct 13 19:27:05 woody1 kernel: [ 1.079676] nf_conntrack version 0.5.0
(16384 buckets, 65536 max)
Oct 13 19:27:05 woody1 kernel: [ 1.079916] ip_tables: (C) 2000-2006
Netfilter Core Team
Oct 13 19:27:05 woody1 kernel: [ 1.080051] TCP cubic registered
Oct 13 19:27:05 woody1 kernel: [ 1.080179] Initializing XFRM netlink
socket
Oct 13 19:27:05 woody1 kernel: [ 1.080310] NET: Registered protocol
family 17
Oct 13 19:27:05 woody1 kernel: [ 1.080446] Registering the
dns_resolver key type
Oct 13 19:27:05 woody1 kernel: [ 1.094904] IMA: No TPM chip found,
activating TPM-bypass!
Oct 13 19:27:05 woody1 kernel: [ 1.095513] rtc_cmos 00:04: setting
system clock to 2011-10-13 18:26:38 UTC (1318530398)
Oct 13 19:27:05 woody1 kernel: [ 1.095755] Initializing network drop
monitor service
Oct 13 19:27:05 woody1 kernel: [ 1.375707] ata4: SATA link up 3.0
Gbps (SStatus 123 SControl 300)
Oct 13 19:27:05 woody1 kernel: [ 1.375868] ata5: SATA link up 3.0
Gbps (SStatus 123 SControl 300)
Oct 13 19:27:05 woody1 kernel: [ 1.376013] ata3: SATA link up 3.0
Gbps (SStatus 123 SControl 300)
Oct 13 19:27:05 woody1 kernel: [ 1.377254] ata4.00: ATA-8:
ST31000333AS, SD1B, max UDMA/133
Oct 13 19:27:05 woody1 kernel: [ 1.377399] ata4.00: 1953525168
sectors, multi 16: LBA48 NCQ (depth 31/32)
Oct 13 19:27:05 woody1 kernel: [ 1.377573] ata3.00: ATA-8:
ST31000333AS, SD1B, max UDMA/133
Oct 13 19:27:05 woody1 kernel: [ 1.377714] ata3.00: 1953525168
sectors, multi 16: LBA48 NCQ (depth 31/32)
Oct 13 19:27:05 woody1 kernel: [ 1.377855] ata5.00: ATA-8:
ST3750330AS, SD15, max UDMA/133
Oct 13 19:27:05 woody1 kernel: [ 1.377985] ata5.00: 1465149168
sectors, multi 16: LBA48 NCQ (depth 31/32)
Oct 13 19:27:05 woody1 kernel: [ 1.379240] ata4.00: configured for
UDMA/133
Oct 13 19:27:05 woody1 kernel: [ 1.379491] ata3.00: configured for
UDMA/133
Oct 13 19:27:05 woody1 kernel: [ 1.379733] scsi 2:0:0:0:
Direct-Access ATA ST31000333AS SD1B PQ: 0 ANSI: 5
Oct 13 19:27:05 woody1 kernel: [ 1.380035] sd 2:0:0:0: Attached scsi
generic sg0 type 0
Oct 13 19:27:05 woody1 kernel: [ 1.380062] ata5.00: configured for
UDMA/133
Oct 13 19:27:05 woody1 kernel: [ 1.380173] sd 2:0:0:0: [sda]
1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
Oct 13 19:27:05 woody1 kernel: [ 1.380332] sd 2:0:0:0: [sda] Write
Protect is off
Oct 13 19:27:05 woody1 kernel: [ 1.380369] sd 2:0:0:0: [sda] Write
cache: enabled, read cache: enabled, doesn't support DPO or FUA
Oct 13 19:27:05 woody1 kernel: [ 1.381066] scsi 3:0:0:0:
Direct-Access ATA ST31000333AS SD1B PQ: 0 ANSI: 5
Oct 13 19:27:05 woody1 kernel: [ 1.381334] sd 3:0:0:0: Attached scsi
generic sg1 type 0
Oct 13 19:27:05 woody1 kernel: [ 1.381370] sd 3:0:0:0: [sdb]
1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
Oct 13 19:27:05 woody1 kernel: [ 1.381431] sd 3:0:0:0: [sdb] Write
Protect is off
Oct 13 19:27:05 woody1 kernel: [ 1.381456] sd 3:0:0:0: [sdb] Write
cache: enabled, read cache: enabled, doesn't support DPO or FUA
Oct 13 19:27:05 woody1 kernel: [ 1.382137] scsi 4:0:0:0:
Direct-Access ATA ST3750330AS SD15 PQ: 0 ANSI: 5
Oct 13 19:27:05 woody1 kernel: [ 1.382402] sd 4:0:0:0: [sdc]
1465149168 512-byte logical blocks: (750 GB/698 GiB)
Oct 13 19:27:05 woody1 kernel: [ 1.382405] sd 4:0:0:0: Attached scsi
generic sg2 type 0
Oct 13 19:27:05 woody1 kernel: [ 1.382843] sd 4:0:0:0: [sdc] Write
Protect is off
Oct 13 19:27:05 woody1 kernel: [ 1.382997] sd 4:0:0:0: [sdc] Write
cache: enabled, read cache: enabled, doesn't support DPO or FUA
Oct 13 19:27:05 woody1 kernel: [ 1.387499] sda: sda1 sda2 sda4
Oct 13 19:27:05 woody1 kernel: [ 1.387930] sd 2:0:0:0: [sda] Attached
SCSI disk
Oct 13 19:27:05 woody1 kernel: [ 1.393659] sdb: sdb1 sdb2 sdb4
Oct 13 19:27:05 woody1 kernel: [ 1.394083] sd 3:0:0:0: [sdb] Attached
SCSI disk
Oct 13 19:27:05 woody1 kernel: [ 1.405653] sdc: sdc4
Oct 13 19:27:05 woody1 kernel: [ 1.406042] sd 4:0:0:0: [sdc] Attached
SCSI disk
Oct 13 19:27:05 woody1 kernel: [ 1.408239] Freeing unused kernel
memory: 1448k freed
Oct 13 19:27:05 woody1 kernel: [ 1.408487] Write protecting the
kernel read-only data: 8192k
Oct 13 19:27:05 woody1 kernel: [ 1.409360] Freeing unused kernel
memory: 156k freed
Oct 13 19:27:05 woody1 kernel: [ 1.415478] Freeing unused kernel
memory: 2020k freed
Oct 13 19:27:05 woody1 kernel: [ 1.942303] Refined TSC clocksource
calibration: 3311.144 MHz.
Oct 13 19:27:05 woody1 kernel: [ 1.942447] Switching to clocksource tsc
Oct 13 19:27:05 woody1 kernel: [ 6.595686] md: md2 stopped.
Oct 13 19:27:05 woody1 kernel: [ 6.597044] md: bind<sda2>
Oct 13 19:27:05 woody1 kernel: [ 6.597416] md: bind<sdb2>
Oct 13 19:27:05 woody1 kernel: [ 6.598608] bio: create slab <bio-1> at 1
Oct 13 19:27:05 woody1 kernel: [ 6.598831] md/raid1:md2: active with
2 out of 2 mirrors
Oct 13 19:27:05 woody1 kernel: [ 6.598971] md2: detected capacity
change from 0 to 249836560384
Oct 13 19:27:05 woody1 kernel: [ 11.609196] md2: unknown partition table
Oct 13 19:27:05 woody1 kernel: [ 16.790558] EXT4-fs (dm-0): mounted
filesystem with ordered data mode. Opts: (null)
Oct 13 19:27:05 woody1 kernel: [ 22.364873] readahead-collector: starting
Oct 13 19:27:05 woody1 kernel: [ 22.667897] udev[125]: starting
version 161
Oct 13 19:27:05 woody1 kernel: [ 22.927556] microcode: CPU0
sig=0x206a7, pf=0x2, revision=0x1a
Oct 13 19:27:05 woody1 kernel: [ 22.936043] input: PC Speaker as
/devices/platform/pcspkr/input/input2
Oct 13 19:27:05 woody1 kernel: [ 22.942729] xhci_hcd 0000:06:00.0: PCI
INT A -> GSI 17 (level, low) -> IRQ 17
Oct 13 19:27:05 woody1 kernel: [ 22.942916] xhci_hcd 0000:06:00.0:
xHCI Host Controller
Oct 13 19:27:05 woody1 kernel: [ 22.943080] xhci_hcd 0000:06:00.0: new
USB bus registered, assigned bus number 1
Oct 13 19:27:05 woody1 kernel: [ 22.950250] xhci_hcd 0000:06:00.0: irq
17, io mem 0xfe300000
Oct 13 19:27:05 woody1 kernel: [ 22.950569] usb usb1: New USB device
found, idVendor=1d6b, idProduct=0002
Oct 13 19:27:05 woody1 kernel: [ 22.950708] usb usb1: New USB device
strings: Mfr=3, Product=2, SerialNumber=1
Oct 13 19:27:05 woody1 kernel: [ 22.950918] usb usb1: Product: xHCI
Host Controller
Oct 13 19:27:05 woody1 kernel: [ 22.951046] usb usb1: Manufacturer:
Linux 3.0.6 xhci_hcd
Oct 13 19:27:05 woody1 kernel: [ 22.951174] usb usb1: SerialNumber:
0000:06:00.0
Oct 13 19:27:05 woody1 kernel: [ 22.951375] hub 1-0:1.0: USB hub found
Oct 13 19:27:05 woody1 kernel: [ 22.951508] hub 1-0:1.0: 2 ports detected
Oct 13 19:27:05 woody1 kernel: [ 22.951682] xhci_hcd 0000:06:00.0:
xHCI Host Controller
Oct 13 19:27:05 woody1 kernel: [ 22.951838] xhci_hcd 0000:06:00.0: new
USB bus registered, assigned bus number 2
Oct 13 19:27:05 woody1 kernel: [ 22.953141] i801_smbus 0000:00:1f.3:
PCI INT C -> GSI 18 (level, low) -> IRQ 18
Oct 13 19:27:05 woody1 kernel: [ 22.955452] usb usb2: New USB device
found, idVendor=1d6b, idProduct=0003
Oct 13 19:27:05 woody1 kernel: [ 22.955584] usb usb2: New USB device
strings: Mfr=3, Product=2, SerialNumber=1
Oct 13 19:27:05 woody1 kernel: [ 22.955787] usb usb2: Product: xHCI
Host Controller
Oct 13 19:27:05 woody1 kernel: [ 22.955911] usb usb2: Manufacturer:
Linux 3.0.6 xhci_hcd
Oct 13 19:27:05 woody1 kernel: [ 22.956044] usb usb2: SerialNumber:
0000:06:00.0
Oct 13 19:27:05 woody1 kernel: [ 22.956239] hub 2-0:1.0: USB hub found
Oct 13 19:27:05 woody1 kernel: [ 22.956370] hub 2-0:1.0: 2 ports detected
Oct 13 19:27:05 woody1 kernel: [ 22.958798] atl1c 0000:07:00.0: PCI
INT A -> GSI 18 (level, low) -> IRQ 18
Oct 13 19:27:05 woody1 kernel: [ 22.974194] tg3.c:v3.119 (May 18, 2011)
Oct 13 19:27:05 woody1 kernel: [ 22.974331] tg3 0000:09:01.0: PCI INT
A -> GSI 16 (level, low) -> IRQ 16
Oct 13 19:27:05 woody1 kernel: [ 22.978516] e1000e: Intel(R) PRO/1000
Network Driver - 1.3.10-k2
Oct 13 19:27:05 woody1 kernel: [ 22.978648] e1000e: Copyright(c) 1999
- 2011 Intel Corporation.
Oct 13 19:27:05 woody1 kernel: [ 22.978785] e1000e 0000:03:00.0:
Disabling ASPM L0s
Oct 13 19:27:05 woody1 kernel: [ 22.978923] e1000e 0000:03:00.0: PCI
INT A -> GSI 18 (level, low) -> IRQ 18
Oct 13 19:27:05 woody1 kernel: [ 22.992670] tg3 0000:09:01.0: eth0:
Tigon3 [partno(3C1000B-T) rev 1002] (PCI:33MHz:32-bit) MAC address
00:0a:5e:00:38:6e
Oct 13 19:27:05 woody1 kernel: [ 22.992882] tg3 0000:09:01.0: eth0:
attached PHY is 5703 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[0])
Oct 13 19:27:05 woody1 kernel: [ 22.993089] tg3 0000:09:01.0: eth0:
RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
Oct 13 19:27:05 woody1 kernel: [ 22.993296] tg3 0000:09:01.0: eth0:
dma_rwctrl[763f0000] dma_mask[64-bit]
Oct 13 19:27:05 woody1 kernel: [ 22.998267] ehci_hcd: USB 2.0
'Enhanced' Host Controller (EHCI) Driver
Oct 13 19:27:05 woody1 kernel: [ 22.998417] ehci_hcd 0000:00:1a.0: PCI
INT A -> GSI 23 (level, low) -> IRQ 23
Oct 13 19:27:05 woody1 kernel: [ 22.998611] ehci_hcd 0000:00:1a.0:
EHCI Host Controller
Oct 13 19:27:05 woody1 kernel: [ 22.998774] ehci_hcd 0000:00:1a.0: new
USB bus registered, assigned bus number 3
Oct 13 19:27:05 woody1 kernel: [ 22.999006] ehci_hcd 0000:00:1a.0:
debug port 2
Oct 13 19:27:05 woody1 kernel: [ 23.001865] microcode: CPU1
sig=0x206a7, pf=0x2, revision=0x1a
Oct 13 19:27:05 woody1 kernel: [ 23.002759] microcode: CPU2
sig=0x206a7, pf=0x2, revision=0x1a
Oct 13 19:27:05 woody1 kernel: [ 23.003019] ehci_hcd 0000:00:1a.0: irq
23, io mem 0xfe707000
Oct 13 19:27:05 woody1 kernel: [ 23.003769] microcode: CPU3
sig=0x206a7, pf=0x2, revision=0x1a
Oct 13 19:27:05 woody1 kernel: [ 23.004279] [drm] Initialized drm
1.1.0 20060810
Oct 13 19:27:05 woody1 kernel: [ 23.004785] microcode: Microcode
Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
Oct 13 19:27:05 woody1 kernel: [ 23.012531] ehci_hcd 0000:00:1a.0: USB
2.0 started, EHCI 1.00
Oct 13 19:27:05 woody1 kernel: [ 23.012700] usb usb3: New USB device
found, idVendor=1d6b, idProduct=0002
Oct 13 19:27:05 woody1 kernel: [ 23.012830] usb usb3: New USB device
strings: Mfr=3, Product=2, SerialNumber=1
Oct 13 19:27:05 woody1 kernel: [ 23.013041] usb usb3: Product: EHCI
Host Controller
Oct 13 19:27:05 woody1 kernel: [ 23.013171] usb usb3: Manufacturer:
Linux 3.0.6 ehci_hcd
Oct 13 19:27:05 woody1 kernel: [ 23.013298] usb usb3: SerialNumber:
0000:00:1a.0
Oct 13 19:27:05 woody1 kernel: [ 23.013502] hub 3-0:1.0: USB hub found
Oct 13 19:27:05 woody1 kernel: [ 23.013638] hub 3-0:1.0: 2 ports detected
Oct 13 19:27:05 woody1 kernel: [ 23.013820] ehci_hcd 0000:00:1d.0: PCI
INT A -> GSI 23 (level, low) -> IRQ 23
Oct 13 19:27:05 woody1 kernel: [ 23.013975] ehci_hcd 0000:00:1d.0:
EHCI Host Controller
Oct 13 19:27:05 woody1 kernel: [ 23.014137] ehci_hcd 0000:00:1d.0: new
USB bus registered, assigned bus number 4
Oct 13 19:27:05 woody1 kernel: [ 23.014366] ehci_hcd 0000:00:1d.0:
debug port 2
Oct 13 19:27:05 woody1 kernel: [ 23.018378] ehci_hcd 0000:00:1d.0: irq
23, io mem 0xfe706000
Oct 13 19:27:05 woody1 kernel: [ 23.027524] ehci_hcd 0000:00:1d.0: USB
2.0 started, EHCI 1.00
Oct 13 19:27:05 woody1 kernel: [ 23.027665] usb usb4: New USB device
found, idVendor=1d6b, idProduct=0002
Oct 13 19:27:05 woody1 kernel: [ 23.027796] usb usb4: New USB device
strings: Mfr=3, Product=2, SerialNumber=1
Oct 13 19:27:05 woody1 kernel: [ 23.028003] usb usb4: Product: EHCI
Host Controller
Oct 13 19:27:05 woody1 kernel: [ 23.028132] usb usb4: Manufacturer:
Linux 3.0.6 ehci_hcd
Oct 13 19:27:05 woody1 kernel: [ 23.028261] usb usb4: SerialNumber:
0000:00:1d.0
Oct 13 19:27:05 woody1 kernel: [ 23.028476] hub 4-0:1.0: USB hub found
Oct 13 19:27:05 woody1 kernel: [ 23.028611] hub 4-0:1.0: 2 ports detected
Oct 13 19:27:05 woody1 kernel: [ 23.036637] md: bind<sdc4>
Oct 13 19:27:05 woody1 kernel: [ 23.060726] atl1c 0000:07:00.0:
version 1.0.1.0-NAPI
Oct 13 19:27:05 woody1 kernel: [ 23.077700] e1000e 0000:03:00.0: eth2:
(PCI Express:2.5GT/s:Width x1) 00:1b:21:ad:77:d1
Oct 13 19:27:05 woody1 kernel: [ 23.077907] e1000e 0000:03:00.0: eth2:
Intel(R) PRO/1000 Network Connection
Oct 13 19:27:05 woody1 kernel: [ 23.078050] e1000e 0000:03:00.0: eth2:
MAC: 3, PHY: 8, PBA No: E46981-005
Oct 13 19:27:05 woody1 kernel: [ 23.086538] udev[134]: renamed network
interface eth2 to eth2-eth0
Oct 13 19:27:05 woody1 kernel: [ 23.107509] udev[131]: renamed network
interface eth0 to eth2
Oct 13 19:27:05 woody1 kernel: [ 23.141511] udev[134]: renamed network
interface eth2-eth0 to eth0
Oct 13 19:27:05 woody1 kernel: [ 23.179765] [drm] radeon defaulting to
kernel modesetting.
Oct 13 19:27:05 woody1 kernel: [ 23.179896] [drm] radeon kernel
modesetting enabled.
Oct 13 19:27:05 woody1 kernel: [ 23.180060] radeon 0000:01:00.0: PCI
INT A -> GSI 16 (level, low) -> IRQ 16
Oct 13 19:27:05 woody1 kernel: [ 23.180333] [drm] initializing kernel
modesetting (RV530 0x1002:0x71C6 0x174B:0x0880).
Oct 13 19:27:05 woody1 kernel: [ 23.180581] [drm] register mmio base:
0xFE630000
Oct 13 19:27:05 woody1 kernel: [ 23.180709] [drm] register mmio size:
65536
Oct 13 19:27:05 woody1 kernel: [ 23.180927] ATOM BIOS: A67105
Oct 13 19:27:05 woody1 kernel: [ 23.181065] [drm] Generation 2 PCI
interface, using max accessible memory
Oct 13 19:27:05 woody1 kernel: [ 23.181197] radeon 0000:01:00.0: VRAM:
256M 0x0000000000000000 - 0x000000000FFFFFFF (256M used)
Oct 13 19:27:05 woody1 kernel: [ 23.181406] radeon 0000:01:00.0: GTT:
512M 0x0000000010000000 - 0x000000002FFFFFFF
Oct 13 19:27:05 woody1 kernel: [ 23.181635] [drm] Supports vblank
timestamp caching Rev 1 (10.10.2010).
Oct 13 19:27:05 woody1 kernel: [ 23.181763] [drm] Driver supports
precise vblank timestamp query.
Oct 13 19:27:05 woody1 kernel: [ 23.181924] radeon 0000:01:00.0:
radeon: using MSI.
Oct 13 19:27:05 woody1 kernel: [ 23.182065] [drm] radeon: irq initialized.
Oct 13 19:27:05 woody1 kernel: [ 23.183206] [drm] Detected VRAM
RAM=256M, BAR=256M
Oct 13 19:27:05 woody1 kernel: [ 23.183338] [drm] RAM width 128bits DDR
Oct 13 19:27:05 woody1 kernel: [ 23.183669] [TTM] Zone kernel:
Available graphics memory: 8226086 kiB.
Oct 13 19:27:05 woody1 kernel: [ 23.183801] [TTM] Zone dma32:
Available graphics memory: 2097152 kiB.
Oct 13 19:27:05 woody1 kernel: [ 23.183929] [TTM] Initializing pool
allocator.
Oct 13 19:27:05 woody1 kernel: [ 23.184070] [drm] radeon: 256M of VRAM
memory ready
Oct 13 19:27:05 woody1 kernel: [ 23.184199] [drm] radeon: 512M of GTT
memory ready.
Oct 13 19:27:05 woody1 kernel: [ 23.184346] [drm] GART: num cpu pages
131072, num gpu pages 131072
Oct 13 19:27:05 woody1 kernel: [ 23.185739] [drm] radeon: 1 quad
pipes, 2 z pipes initialized.
Oct 13 19:27:05 woody1 kernel: [ 23.186403] [drm] PCIE GART of 512M
enabled (table at 0x00040000).
Oct 13 19:27:05 woody1 kernel: [ 23.186544] radeon 0000:01:00.0: WB
enabled
Oct 13 19:27:05 woody1 kernel: [ 23.186712] [drm] Loading R500 Microcode
Oct 13 19:27:05 woody1 kernel: [ 23.219179] md: bind<sdb4>
Oct 13 19:27:05 woody1 kernel: [ 23.234390] [drm] radeon: ring at
0x0000000010001000
Oct 13 19:27:05 woody1 kernel: [ 23.234546] [drm] ring test succeeded
in 8 usecs
Oct 13 19:27:05 woody1 kernel: [ 23.234734] [drm] radeon: ib pool ready.
Oct 13 19:27:05 woody1 kernel: [ 23.234953] [drm] ib test succeeded in
0 usecs
Oct 13 19:27:05 woody1 kernel: [ 23.235215] [drm] Radeon Display
Connectors
Oct 13 19:27:05 woody1 kernel: [ 23.235348] [drm] Connector 0:
Oct 13 19:27:05 woody1 kernel: [ 23.235475] [drm] DVI-I
Oct 13 19:27:05 woody1 kernel: [ 23.235601] [drm] HPD2
Oct 13 19:27:05 woody1 kernel: [ 23.235728] [drm] DDC: 0x7e40 0x7e40
0x7e44 0x7e44 0x7e48 0x7e48 0x7e4c 0x7e4c
Oct 13 19:27:05 woody1 kernel: [ 23.235933] [drm] Encoders:
Oct 13 19:27:05 woody1 kernel: [ 23.236060] [drm] CRT1:
INTERNAL_KLDSCP_DAC1
Oct 13 19:27:05 woody1 kernel: [ 23.236187] [drm] DFP3: INTERNAL_LVTM1
Oct 13 19:27:05 woody1 kernel: [ 23.236314] [drm] Connector 1:
Oct 13 19:27:05 woody1 kernel: [ 23.236442] [drm] S-video
Oct 13 19:27:05 woody1 kernel: [ 23.236568] [drm] Encoders:
Oct 13 19:27:05 woody1 kernel: [ 23.236693] [drm] TV1:
INTERNAL_KLDSCP_DAC2
Oct 13 19:27:05 woody1 kernel: [ 23.236822] [drm] Connector 2:
Oct 13 19:27:05 woody1 kernel: [ 23.236949] [drm] DVI-I
Oct 13 19:27:05 woody1 kernel: [ 23.237076] [drm] HPD1
Oct 13 19:27:05 woody1 kernel: [ 23.237203] [drm] DDC: 0x7e50 0x7e50
0x7e54 0x7e54 0x7e58 0x7e58 0x7e5c 0x7e5c
Oct 13 19:27:05 woody1 kernel: [ 23.237411] [drm] Encoders:
Oct 13 19:27:05 woody1 kernel: [ 23.237538] [drm] CRT2:
INTERNAL_KLDSCP_DAC2
Oct 13 19:27:05 woody1 kernel: [ 23.237665] [drm] DFP1:
INTERNAL_KLDSCP_TMDS1
Oct 13 19:27:05 woody1 kernel: [ 23.247573] [drm] Radeon display
connector DVI-I-1: No monitor connected or invalid EDID
Oct 13 19:27:05 woody1 kernel: [ 23.268871] md: bind<sdb1>
Oct 13 19:27:05 woody1 kernel: [ 23.300382] [drm] Radeon display
connector DVI-I-2: Found valid EDID
Oct 13 19:27:05 woody1 kernel: [ 23.300441] [drm] Possible lm63
thermal controller at 0x4c
Oct 13 19:27:05 woody1 kernel: [ 23.305241] md: bind<sda1>
Oct 13 19:27:05 woody1 kernel: [ 23.306934] md/raid1:md1: active with
2 out of 2 mirrors
Oct 13 19:27:05 woody1 kernel: [ 23.307073] md1: detected capacity
change from 0 to 209649664
Oct 13 19:27:05 woody1 kernel: [ 23.308197] md1: unknown partition table
Oct 13 19:27:05 woody1 kernel: [ 23.316277] usb 3-1: new high speed
USB device number 2 using ehci_hcd
Oct 13 19:27:05 woody1 kernel: [ 23.339184] md: bind<sda4>
Oct 13 19:27:05 woody1 kernel: [ 23.341348] md/raid:md3: device sda4
operational as raid disk 2
Oct 13 19:27:05 woody1 kernel: [ 23.341487] md/raid:md3: device sdb4
operational as raid disk 0
Oct 13 19:27:05 woody1 kernel: [ 23.341622] md/raid:md3: device sdc4
operational as raid disk 1
Oct 13 19:27:05 woody1 kernel: [ 23.341944] md/raid:md3: allocated 3230kB
Oct 13 19:27:05 woody1 kernel: [ 23.342094] md/raid:md3: raid level 5
active with 3 out of 3 devices, algorithm 2
Oct 13 19:27:05 woody1 kernel: [ 23.342340] md3: detected capacity
change from 0 to 1500307259392
Oct 13 19:27:05 woody1 kernel: [ 23.343367] md3: unknown partition table
Oct 13 19:27:05 woody1 kernel: [ 23.378931] [drm] fb mappable at
0xD00C0000
Oct 13 19:27:05 woody1 kernel: [ 23.379062] [drm] vram apper at 0xD0000000
Oct 13 19:27:05 woody1 kernel: [ 23.379190] [drm] size 5242880
Oct 13 19:27:05 woody1 kernel: [ 23.379318] [drm] fb depth is 24
Oct 13 19:27:05 woody1 kernel: [ 23.379443] [drm] pitch is 5120
Oct 13 19:27:05 woody1 kernel: [ 23.379611] fbcon: radeondrmfb (fb0)
is primary device
Oct 13 19:27:05 woody1 kernel: [ 23.390012] Console: switching to
colour frame buffer device 160x64
Oct 13 19:27:05 woody1 kernel: [ 23.394666] fb0: radeondrmfb frame
buffer device
Oct 13 19:27:05 woody1 kernel: [ 23.394691] drm: registered panic notifier
Oct 13 19:27:05 woody1 kernel: [ 23.394717] [drm] Initialized radeon
2.10.0 20080528 for 0000:01:00.0 on minor 0
Oct 13 19:27:05 woody1 kernel: [ 23.430587] usb 3-1: New USB device
found, idVendor=8087, idProduct=0024
Oct 13 19:27:05 woody1 kernel: [ 23.430638] usb 3-1: New USB device
strings: Mfr=0, Product=0, SerialNumber=0
Oct 13 19:27:05 woody1 kernel: [ 23.430884] hub 3-1:1.0: USB hub found
Oct 13 19:27:05 woody1 kernel: [ 23.430954] hub 3-1:1.0: 6 ports detected
Oct 13 19:27:05 woody1 kernel: [ 23.533144] usb 4-1: new high speed
USB device number 2 using ehci_hcd
Oct 13 19:27:05 woody1 kernel: [ 23.648403] usb 4-1: New USB device
found, idVendor=8087, idProduct=0024
Oct 13 19:27:05 woody1 kernel: [ 23.648454] usb 4-1: New USB device
strings: Mfr=0, Product=0, SerialNumber=0
Oct 13 19:27:05 woody1 kernel: [ 23.648675] hub 4-1:1.0: USB hub found
Oct 13 19:27:05 woody1 kernel: [ 23.648773] hub 4-1:1.0: 8 ports detected
Oct 13 19:27:05 woody1 kernel: [ 23.923934] usb 4-1.1: new full speed
USB device number 3 using ehci_hcd
Oct 13 19:27:05 woody1 kernel: [ 24.009104] usb 4-1.1: New USB device
found, idVendor=0557, idProduct=7000
Oct 13 19:27:05 woody1 kernel: [ 24.009156] usb 4-1.1: New USB device
strings: Mfr=0, Product=0, SerialNumber=0
Oct 13 19:27:05 woody1 kernel: [ 24.009375] hub 4-1.1:1.0: USB hub found
Oct 13 19:27:05 woody1 kernel: [ 24.009470] hub 4-1.1:1.0: 4 ports
detected
Oct 13 19:27:05 woody1 kernel: [ 24.082800] usb 4-1.2: new low speed
USB device number 4 using ehci_hcd
Oct 13 19:27:05 woody1 kernel: [ 24.175392] usb 4-1.2: New USB device
found, idVendor=046d, idProduct=c521
Oct 13 19:27:05 woody1 kernel: [ 24.175448] usb 4-1.2: New USB device
strings: Mfr=1, Product=2, SerialNumber=0
Oct 13 19:27:05 woody1 kernel: [ 24.175489] usb 4-1.2: Product: USB
Receiver
Oct 13 19:27:05 woody1 kernel: [ 24.175513] usb 4-1.2: Manufacturer:
Logitech
Oct 13 19:27:05 woody1 kernel: [ 24.180952] input: Logitech USB
Receiver as
/devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.2/4-1.2:1.0/input/input3
Oct 13 19:27:05 woody1 kernel: [ 24.181064] generic-usb
0003:046D:C521.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB
Receiver] on usb-0000:00:1d.0-1.2/input0
Oct 13 19:27:05 woody1 kernel: [ 24.187424] input: Logitech USB
Receiver as
/devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.2/4-1.2:1.1/input/input4
Oct 13 19:27:05 woody1 kernel: [ 24.187560] generic-usb
0003:046D:C521.0002: input,hiddev0,hidraw1: USB HID v1.11 Device
[Logitech USB Receiver] on usb-0000:00:1d.0-1.2/input1
Oct 13 19:27:05 woody1 kernel: [ 24.260654] usb 4-1.6: new high speed
USB device number 5 using ehci_hcd
Oct 13 19:27:05 woody1 kernel: [ 24.347694] usb 4-1.6: New USB device
found, idVendor=05e3, idProduct=0608
Oct 13 19:27:05 woody1 kernel: [ 24.347745] usb 4-1.6: New USB device
strings: Mfr=0, Product=1, SerialNumber=0
Oct 13 19:27:05 woody1 kernel: [ 24.347796] usb 4-1.6: Product: USB2.0 Hub
Oct 13 19:27:05 woody1 kernel: [ 24.348104] hub 4-1.6:1.0: USB hub found
Oct 13 19:27:05 woody1 kernel: [ 24.348475] hub 4-1.6:1.0: 4 ports
detected
Oct 13 19:27:05 woody1 kernel: [ 24.423521] usb 4-1.1.1: new low speed
USB device number 6 using ehci_hcd
Oct 13 19:27:05 woody1 kernel: [ 24.543035] usb 4-1.1.1: New USB
device found, idVendor=0d3d, idProduct=0001
Oct 13 19:27:05 woody1 kernel: [ 24.543091] usb 4-1.1.1: New USB
device strings: Mfr=0, Product=2, SerialNumber=0
Oct 13 19:27:05 woody1 kernel: [ 24.543133] usb 4-1.1.1: Product: USBPS2
Oct 13 19:27:05 woody1 kernel: [ 24.582173] input: USBPS2 as
/devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.1/4-1.1.1/4-1.1.1:1.0/input/input5
Oct 13 19:27:05 woody1 kernel: [ 24.583859] generic-usb
0003:0D3D:0001.0003: input,hidraw2: USB HID v1.00 Keyboard [USBPS2] on
usb-0000:00:1d.0-1.1.1/input0
Oct 13 19:27:05 woody1 kernel: [ 24.627646] input: USBPS2 as
/devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.1/4-1.1.1/4-1.1.1:1.1/input/input6
Oct 13 19:27:05 woody1 kernel: [ 24.629451] generic-usb
0003:0D3D:0001.0004: input,hidraw3: USB HID v1.00 Mouse [USBPS2] on
usb-0000:00:1d.0-1.1.1/input1
Oct 13 19:27:05 woody1 kernel: [ 24.694419] usb 4-1.6.4: new full
speed USB device number 7 using ehci_hcd
Oct 13 19:27:05 woody1 kernel: [ 24.771091] usb 4-1.6.4: New USB
device found, idVendor=058f, idProduct=9254
Oct 13 19:27:05 woody1 kernel: [ 24.772872] usb 4-1.6.4: New USB
device strings: Mfr=1, Product=2, SerialNumber=0
Oct 13 19:27:05 woody1 kernel: [ 24.774633] usb 4-1.6.4: Product:
Generic USB Hub
Oct 13 19:27:05 woody1 kernel: [ 24.776378] usb 4-1.6.4: Manufacturer:
ALCOR
Oct 13 19:27:05 woody1 kernel: [ 24.778360] hub 4-1.6.4:1.0: USB hub found
Oct 13 19:27:05 woody1 kernel: [ 24.780212] hub 4-1.6.4:1.0: 4 ports
detected
Oct 13 19:27:05 woody1 kernel: [ 25.043997] usb 4-1.6.4.1: new full
speed USB device number 8 using ehci_hcd
Oct 13 19:27:05 woody1 kernel: [ 25.127252] usb 4-1.6.4.1: New USB
device found, idVendor=04b8, idProduct=0005
Oct 13 19:27:05 woody1 kernel: [ 25.129108] usb 4-1.6.4.1: New USB
device strings: Mfr=1, Product=2, SerialNumber=3
Oct 13 19:27:05 woody1 kernel: [ 25.130959] usb 4-1.6.4.1: Product:
USB Printer
Oct 13 19:27:05 woody1 kernel: [ 25.132816] usb 4-1.6.4.1:
Manufacturer: EPSON
Oct 13 19:27:05 woody1 kernel: [ 25.134677] usb 4-1.6.4.1:
SerialNumber: 123450610171029400
Oct 13 19:27:05 woody1 kernel: [ 25.159808] usblp0: USB Bidirectional
printer dev 8 if 0 alt 0 proto 2 vid 0x04B8 pid 0x0005
Oct 13 19:27:05 woody1 kernel: [ 25.161685] usbcore: registered new
interface driver usblp
Oct 13 19:27:05 woody1 kernel: [ 25.198864] usb 4-1.6.4.4: new full
speed USB device number 9 using ehci_hcd
Oct 13 19:27:05 woody1 kernel: [ 25.286535] usb 4-1.6.4.4: not running
at top speed; connect to a high speed hub
Oct 13 19:27:05 woody1 kernel: [ 25.290719] usb 4-1.6.4.4: New USB
device found, idVendor=04a9, idProduct=10d2
Oct 13 19:27:05 woody1 kernel: [ 25.292628] usb 4-1.6.4.4: New USB
device strings: Mfr=1, Product=2, SerialNumber=3
Oct 13 19:27:05 woody1 kernel: [ 25.294541] usb 4-1.6.4.4: Product:
iP4700 series
Oct 13 19:27:05 woody1 kernel: [ 25.296430] usb 4-1.6.4.4:
Manufacturer: Canon
Oct 13 19:27:05 woody1 kernel: [ 25.298308] usb 4-1.6.4.4:
SerialNumber: A109B0
Oct 13 19:27:05 woody1 kernel: [ 25.304292] usblp1: USB Bidirectional
printer dev 9 if 0 alt 0 proto 2 vid 0x04A9 pid 0x10D2
Oct 13 19:27:05 woody1 kernel: [ 25.433058] EXT4-fs (dm-0):
re-mounted. Opts: (null)
Oct 13 19:27:05 woody1 kernel: [ 25.739926] EXT4-fs (md1): mounted
filesystem with ordered data mode. Opts: (null)
Oct 13 19:27:05 woody1 kernel: [ 25.773623] EXT4-fs (dm-1): mounted
filesystem with ordered data mode. Opts: (null)
Oct 13 19:27:05 woody1 kernel: [ 25.805764] EXT4-fs (dm-2): mounted
filesystem with ordered data mode. Opts: (null)
Oct 13 19:27:05 woody1 kernel: [ 25.880740] EXT4-fs (dm-8): mounted
filesystem with ordered data mode. Opts: (null)
Oct 13 19:27:05 woody1 kernel: [ 25.885594] EXT4-fs (dm-9): mounted
filesystem with ordered data mode. Opts: (null)
Oct 13 19:27:05 woody1 kernel: [ 27.105218] Adding 2097148k swap on
/dev/mapper/vg1a-swap. Priority:-1 extents:1 across:2097148k
Oct 13 19:27:05 woody1 kernel: [ 27.343638] readahead-disable-service:
delaying service auditd
Oct 13 19:27:05 woody1 cpuspeed: Enabling ondemand cpu frequency scaling
governor
Oct 13 19:27:06 woody1 rpcbind: cannot create socket for udp6
Oct 13 19:27:06 woody1 rpcbind: cannot create socket for tcp6
Oct 13 19:27:06 woody1 rpc.statd[802]: Version 1.2.3 starting
Oct 13 19:27:06 woody1 sm-notify[803]: Version 1.2.3 starting
Oct 13 19:27:06 woody1 kernel: [ 28.974702] RPC: Registered named UNIX
socket transport module.
Oct 13 19:27:06 woody1 kernel: [ 28.976576] RPC: Registered udp
transport module.
Oct 13 19:27:06 woody1 kernel: [ 28.976577] RPC: Registered tcp
transport module.
Oct 13 19:27:06 woody1 kernel: [ 28.976578] RPC: Registered tcp
NFSv4.1 backchannel transport module.
Oct 13 19:27:07 woody1 kernel: [ 29.579706] Bridge firewalling registered
Oct 13 19:27:08 woody1 kernel: [ 31.046070] atl1c 0000:07:00.0: atl1c:
eth1 NIC Link is Up<1000 Mbps Full Duplex>
Oct 13 19:27:08 woody1 kernel: [ 31.074431] tun: Universal TUN/TAP
device driver, 1.6
Oct 13 19:27:08 woody1 kernel: [ 31.074435] tun: (C) 1999-2004 Max
Krasnyansky <maxk@qualcomm.com>
Oct 13 19:27:09 woody1 kernel: [ 32.121206] device eth0 entered
promiscuous mode
Oct 13 19:27:09 woody1 kernel: [ 32.123605] device tap10 entered
promiscuous mode
Oct 13 19:27:09 woody1 kernel: [ 32.131482] device eth1 entered
promiscuous mode
Oct 13 19:27:09 woody1 kernel: [ 32.133813] device tap11 entered
promiscuous mode
Oct 13 19:27:09 woody1 kernel: [ 32.135467] br1: port 1(eth1) entering
forwarding state
Oct 13 19:27:09 woody1 kernel: [ 32.135471] br1: port 1(eth1) entering
forwarding state
Oct 13 19:27:10 woody1 kernel: [ 32.693502] e1000e: eth0 NIC Link is
Up 100 Mbps Full Duplex, Flow Control: Rx/Tx
Oct 13 19:27:10 woody1 kernel: [ 32.693508] e1000e 0000:03:00.0: eth0:
10/100 speed: disabling TSO
Oct 13 19:27:10 woody1 kernel: [ 32.695107] br0: port 1(eth0) entering
forwarding state
Oct 13 19:27:10 woody1 kernel: [ 32.695111] br0: port 1(eth0) entering
forwarding state
Oct 13 19:27:12 woody1 kernel: [ 34.903067] tg3 0000:09:01.0: eth2:
Link is up at 1000 Mbps, full duplex
Oct 13 19:27:12 woody1 kernel: [ 34.903072] tg3 0000:09:01.0: eth2:
Flow control is on for TX and on for RX
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PROBLEM] ASUS Sandybridge motherboards + PCI not working (IRQ n: nobody cared)
2011-10-15 8:43 ` Chris Palmer
@ 2011-10-15 16:23 ` Robert Hancock
[not found] ` <4EE72C4D.9080207@pobox.com>
0 siblings, 1 reply; 7+ messages in thread
From: Robert Hancock @ 2011-10-15 16:23 UTC (permalink / raw)
To: Chris Palmer; +Cc: linux-kernel, linux-acpi
On Sat, Oct 15, 2011 at 2:43 AM, Chris Palmer <chris.palmer@pobox.com> wrote:
> On 15/10/2011 01:29, Robert Hancock wrote:
>> On 10/14/2011 05:04 AM, Chris Palmer wrote:
>>> Interrupt handling for *PCI boards with ASUS Sandybridge motherboards*
>>> seems to be broken.
>>>
>>> It has been seen with network and non-network PCI boards. PCIx network
>>> boards work OK. And all reports are for ASUS motherboards.
>>>
>>> It always results in the infamous "IRQ n: nobody cared" message usually
>>> within an hour. It is possible to restart things by rmmod/modprobe on
>>> the appropriate PCI driver.
>>>
>>> Andrew Morton kindly took a quick look and thinks it is most likely an
>>> ACPI bug.
>>>
>>> Configuration summary:
>>> - ASUS P8H67-V/R3 Motherboard (others have problems with similar M/Bs)
>>> - M/B BIOS 0804 (just updated to that - no change)
>>> - Core i5/2500K
>>> - Onboard ethernet (at11c driver - works)
>>> - Additional PCIx Intel ethernet board (e1000e driver - works)
>>> - Additional PCI Broadcom BCM5702X ethernet board (tg3 driver - fails)
>>> [ Also fails with other PCI boards such as RTL8139 ]
>>> - Kernel 3.0.6
>>>
>>>
>>> Any help much appreciated...
>>>
>>> Previous references:
>>>
>>> https://lkml.org/lkml/2011/6/30/197
>>> https://bugzilla.kernel.org/show_bug.cgi?id=38632
>>> https://bugzilla.redhat.com/show_bug.cgi?id=713351
>>> https://bugzilla.kernel.org/show_bug.cgi?id=35332
>>> https://bugzilla.kernel.org/show_bug.cgi?id=34242
>>> https://bugzilla.kernel.org/show_bug.cgi?id=32242
>>> https://bugzilla.kernel.org/show_bug.cgi?id=39122
>>
>> The bugzilla reports aren't currently accessible so I don't know if it
>> was posted there, but can you post the output of "lspci -vv" as root?
>> Could be that some other device is configured on that IRQ and
>> sometimes spuriously generates interrupts.
>>
>
> Robert
>
> Various outputs below.
>
> Many thanks
> Chris
>
The only device lspci lists as using IRQ 16 is the network card:
09:01.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5702X
Gigabit Ethernet (rev 02)
Subsystem: 3Com Corporation Device 1100
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (16000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
But dmesg has some references to other devices routed to IRQ 16:
Oct 13 19:27:05 woody1 kernel: [ 0.604919] pci 0000:00:01.0: PCI
INT A -> GSI 16 (level, low) -> IRQ 16
This is the PCI-E root port. lspci doesn't list any INTx interrupt for
this device but does list MSI as being enabled with vector 4159.
Oct 13 19:27:05 woody1 kernel: [ 0.605616] pci 0000:00:1c.5: PCI
INT B -> GSI 16 (level, low) -> IRQ 16
This is the PCI-E root port 6, which the USB3 XHCI controller is
attached to. Likewise no INTx interrupt is listed but MSI is enabled
with vector 4181.
Oct 13 19:27:05 woody1 kernel: [ 23.180060] radeon 0000:01:00.0: PCI
INT A -> GSI 16 (level, low) -> IRQ 16
This is the video card. lspci lists it as being on INTx IRQ 56, and
MSI is enabled with vector 4122.
I'm not quite sure what to make of this. It looks like somehow the
kernel's IRQ routing is inconsistent with what lspci is reporting. My
guess is that eventually one of these other devices that's actually
routed to IRQ 16 actually generates an interrupt and nothing is set up
to handle it.
CCing linux-acpi.
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PROBLEM] ASUS Sandybridge motherboards + PCI not working (IRQ n: nobody cared)
2011-10-14 11:04 [PROBLEM] ASUS Sandybridge motherboards + PCI not working (IRQ n: nobody cared) Chris Palmer
2011-10-15 0:29 ` Robert Hancock
@ 2011-10-15 16:51 ` Thomas Backlund
1 sibling, 0 replies; 7+ messages in thread
From: Thomas Backlund @ 2011-10-15 16:51 UTC (permalink / raw)
To: linux-kernel@vger.kernel.org
Chris Palmer skrev 14.10.2011 14:04:
> Interrupt handling for *PCI boards with ASUS Sandybridge motherboards*
> seems to be broken.
>
> It has been seen with network and non-network PCI boards. PCIx network
> boards work OK. And all reports are for ASUS motherboards.
>
> It always results in the infamous "IRQ n: nobody cared" message usually
> within an hour. It is possible to restart things by rmmod/modprobe on
> the appropriate PCI driver.
>
> Andrew Morton kindly took a quick look and thinks it is most likely an
> ACPI bug.
>
> Configuration summary:
> - ASUS P8H67-V/R3 Motherboard (others have problems with similar M/Bs)
> - M/B BIOS 0804 (just updated to that - no change)
> - Core i5/2500K
> - Onboard ethernet (at11c driver - works)
> - Additional PCIx Intel ethernet board (e1000e driver - works)
> - Additional PCI Broadcom BCM5702X ethernet board (tg3 driver - fails)
> [ Also fails with other PCI boards such as RTL8139 ]
> - Kernel 3.0.6
>
>
> Any help much appreciated...
>
Does it help to boot with: pci=nocrs ?
--
Thomas
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: Fwd: Re: [PROBLEM] ASUS Sandybridge motherboards + PCI not working (IRQ n: nobody cared)
[not found] ` <4EE72C4D.9080207@pobox.com>
@ 2011-12-14 0:12 ` Edward Donovan
[not found] ` <CADdbW+E9=DKZ-839yPW_R4JM1omXEzqGqT=ae7Txu4Jikyw2=A@mail.gmail.com>
1 sibling, 0 replies; 7+ messages in thread
From: Edward Donovan @ 2011-12-14 0:12 UTC (permalink / raw)
To: Chris Palmer; +Cc: torvalds, linux-kernel
Hi Chris -
[Dammit, accidentally sent an html mail. Should have stepped out of gmail,
sorry.]
I will certainly take a look. I don't have the hardware, unfortunately. And
this is kinda my first rodeo, kernel-wise, so don't let me sound too expert. :)
Let me ask a couple questions, anyway.
- Later, I'll have time to look for Andrew's message, but do you know -- did he
mean an ACPI bug in the firmware, or in Linux?
- Does 2.6.38 behave the same as 3.1.5 or the other newest kernels? (If the
hardware doesn't require something newer than .38.) There was an IRQ overhaul
in 2.6.39, and the two bugs I fixed were regressions from that work. As of
now, the bad-irq handling seems equivalent to 2.6.38, but I should make sure
that goes for your problem, too.
I think I'll cc LKML, too, if you don't mind. I've seen this topic going by,
but don't know what's been said. And maybe tomorrow I can get some pondering
time -
Ed
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PROBLEM] ASUS Sandybridge motherboards + PCI not working (IRQ n: nobody cared)
[not found] ` <CADdbW+E9=DKZ-839yPW_R4JM1omXEzqGqT=ae7Txu4Jikyw2=A@mail.gmail.com>
@ 2011-12-14 10:49 ` Chris Palmer
0 siblings, 0 replies; 7+ messages in thread
From: Chris Palmer @ 2011-12-14 10:49 UTC (permalink / raw)
To: Edward Donovan; +Cc: torvalds, linux-kernel
Hi Edward
Thanks for the reply. See below...
Regards
Chris
On 14/12/2011 00:06, Edward Donovan wrote:
> Hi Chris -
>
> I will certainly take a look. I don't have the hardware,
> unfortunately. And
> this is kinda my first rodeo, kernel-wise, so don't let me sound too
> expert. :)
> Let me ask a couple questions, anyway.
>
> - Later, I'll have time to look for Andrew's message, but do you know
> -- did he
> mean a firmware ACPI bug, or a Linux bug?
He didn't say.
>
> - Does 2.6.38 behave the same as 3.1.5 or the other newest kernels?
> (If the
> hardware doesn't require something newer than .38.) There was an
> IRQ overhaul
> in 2.6.39, and the two bugs I fixed were regressions from that
> work. As of
> now, the bad-irq handling seems equivalent to 2.6.38, but I should
> make sure
> that goes for your problem, too.
I was on 2.6.39.2 when I purchased the motherboard, so can't personally
vouch for anything earlier. However other posters, who were on earlier
kernels, referred to the behaviour that I am now experiencing on 3.1.5 -
i.e. that the "nobody cared" fault occurs and the device then continues
to "work" but extremely slowly (from 2.6.39.2-3.1.4 it stops working
completely).
>
> I think I'll cc LKML, too, if you don't mind. I've seen this topic
> going by,
> but don't know what's been said. And maybe tomorrow I can get some
> pondering
> time -
>
> Ed
>
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2011-12-14 11:07 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2011-10-14 11:04 [PROBLEM] ASUS Sandybridge motherboards + PCI not working (IRQ n: nobody cared) Chris Palmer
2011-10-15 0:29 ` Robert Hancock
2011-10-15 8:43 ` Chris Palmer
2011-10-15 16:23 ` Robert Hancock
[not found] ` <4EE72C4D.9080207@pobox.com>
2011-12-14 0:12 ` Fwd: " Edward Donovan
[not found] ` <CADdbW+E9=DKZ-839yPW_R4JM1omXEzqGqT=ae7Txu4Jikyw2=A@mail.gmail.com>
2011-12-14 10:49 ` Chris Palmer
2011-10-15 16:51 ` Thomas Backlund
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).