Re: [PATCH RFT v2] regulator: ab8500: Update info->update_val only when successfully update register

["Bengt Jönsson" <bengt.g.jonsson@stericsson.com>]

On 03/28/2013 10:23 AM, Axel Lin wrote:
> Don't update info->update_val if write to the register fails.
>
> Signed-off-by: Axel Lin <axel.lin@ingics.com>
> ---
> v2:
> On the second thought, I think it's ok to update info->update_val when
> regulator is disabled, the mode will change when the regulator is enabled.
That is better of course. I did not notice before.
> Hi Bengt,
> I just got your Ack for v1.
> Can you review this v2 again, and let Mark know which version do you prefer.
>
> Thanks.
> Axel
I prefer this v2, thanks.

Acked-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
>   drivers/regulator/ab8500.c |   27 +++++++++++++++++++--------
>   1 file changed, 19 insertions(+), 8 deletions(-)
>
> diff --git a/drivers/regulator/ab8500.c b/drivers/regulator/ab8500.c
> index 12e2740..7814ac3 100644
> --- a/drivers/regulator/ab8500.c
> +++ b/drivers/regulator/ab8500.c
> @@ -182,8 +182,8 @@ static unsigned int ab8500_regulator_get_optimum_mode(
>   static int ab8500_regulator_set_mode(struct regulator_dev *rdev,
>   				     unsigned int mode)
>   {
> -	int ret = 0;
> -
> +	int ret;
> +	u8 update_val;
>   	struct ab8500_regulator_info *info = rdev_get_drvdata(rdev);
>   
>   	if (info == NULL) {
> @@ -193,31 +193,42 @@ static int ab8500_regulator_set_mode(struct regulator_dev *rdev,
>   
>   	switch (mode) {
>   	case REGULATOR_MODE_NORMAL:
> -		info->update_val = info->update_val_normal;
> +		update_val = info->update_val_normal;
>   		break;
>   	case REGULATOR_MODE_IDLE:
> -		info->update_val = info->update_val_idle;
> +		update_val = info->update_val_idle;
>   		break;
>   	default:
>   		return -EINVAL;
>   	}
>   
> +	/* ab8500 regulators share mode and enable in the same register bits.
> +	   off = 0b00
> +	   low power mode= 0b11
> +	   full powermode = 0b01
> +	   (HW control mode = 0b10)
> +	   Thus we don't write to the register when regulator is disabled.
> +	*/
>   	if (info->is_enabled) {
>   		ret = abx500_mask_and_set_register_interruptible(info->dev,
>   			info->update_bank, info->update_reg,
> -			info->update_mask, info->update_val);
> -		if (ret < 0)
> +			info->update_mask, update_val);
> +		if (ret < 0) {
>   			dev_err(rdev_get_dev(rdev),
>   				"couldn't set regulator mode\n");
> +			return ret;
> +		}
>   
>   		dev_vdbg(rdev_get_dev(rdev),
>   			"%s-set_mode (bank, reg, mask, value): "
>   			"0x%x, 0x%x, 0x%x, 0x%x\n",
>   			info->desc.name, info->update_bank, info->update_reg,
> -			info->update_mask, info->update_val);
> +			info->update_mask, update_val);
>   	}
>   
> -	return ret;
> +	info->update_val = update_val;
> +
> +	return 0;
>   }
>   
>   static unsigned int ab8500_regulator_get_mode(struct regulator_dev *rdev)