Re: [RFT][PATCH 2/3] regulator: ab8500-ext: Don't update info->update_val if set_mode() fails

["Bengt Jönsson" <bengt.g.jonsson@stericsson.com>]

On 04/10/2013 02:55 PM, Axel Lin wrote:
> This ensures info->update_val status is still correct if set_mode() call fails.
> Otherwise, get_mode() may return wrong status if a set_mode() call fails.
>
> Signed-off-by: Axel Lin <axel.lin@ingics.com>
> ---
>   drivers/regulator/ab8500-ext.c |   19 ++++++++++++-------
>   1 file changed, 12 insertions(+), 7 deletions(-)
>
> diff --git a/drivers/regulator/ab8500-ext.c b/drivers/regulator/ab8500-ext.c
> index f0a1bbf..1efe702 100644
> --- a/drivers/regulator/ab8500-ext.c
> +++ b/drivers/regulator/ab8500-ext.c
> @@ -181,6 +181,7 @@ static int ab8500_ext_regulator_set_mode(struct regulator_dev *rdev,
>   {
>   	int ret = 0;
>   	struct ab8500_ext_regulator_info *info = rdev_get_drvdata(rdev);
> +	u8 regval;
>   
>   	if (info == NULL) {
>   		dev_err(rdev_get_dev(rdev), "regulator info null pointer\n");
> @@ -189,14 +190,14 @@ static int ab8500_ext_regulator_set_mode(struct regulator_dev *rdev,
>   
>   	switch (mode) {
>   	case REGULATOR_MODE_NORMAL:
> -		info->update_val = info->update_val_hp;
> +		regval = info->update_val_hp;
>   		break;
>   	case REGULATOR_MODE_IDLE:
>   		/* Always on with high power mode if info->cfg->hwreq is set */
>   		if (info->cfg && info->cfg->hwreq)
>   			return -EINVAL;
>   
> -		info->update_val = info->update_val_lp;
> +		regval = info->update_val_lp;
>   		break;
>   
>   	default:
> @@ -204,12 +205,14 @@ static int ab8500_ext_regulator_set_mode(struct regulator_dev *rdev,
>   	}
>   
>   	if (ab8500_ext_regulator_is_enabled(rdev)) {
> -		u8 regval;
> -
> -		ret = enable(info, &regval);
> -		if (ret < 0)
> +		ret = abx500_mask_and_set_register_interruptible(info->dev,
> +					info->update_bank, info->update_reg,
> +					info->update_mask, regval);
> +		if (ret < 0) {
>   			dev_err(rdev_get_dev(rdev),
>   				"Could not set regulator mode.\n");
> +			return ret;
> +		}
>   
>   		dev_dbg(rdev_get_dev(rdev),
>   			"%s-set_mode (bank, reg, mask, value): "
> @@ -218,7 +221,9 @@ static int ab8500_ext_regulator_set_mode(struct regulator_dev *rdev,
>   			info->update_mask, regval);
>   	}
>   
> -	return ret;
> +	info->update_val = regval;
> +
> +	return 0;
>   }
>   
>   static unsigned int ab8500_ext_regulator_get_mode(struct regulator_dev *rdev)
This patch is needed to fix the error path but it partly depends on the 
previous patch so I would like to get that one sorted out before ack-ing 
this patch.

Regards,

Bengt