From: Rohit Vaswani <rvaswani@codeaurora.org>
To: Stephen Boyd <sboyd@codeaurora.org>
Cc: Linus Walleij <linus.walleij@linaro.org>,
Grant Likely <grant.likely@linaro.org>,
Rob Herring <rob.herring@calxeda.com>,
Rob Landley <rob@landley.net>,
Russell King <linux@arm.linux.org.uk>,
David Brown <davidb@codeaurora.org>,
Bryan Huntsman <bryanh@codeaurora.org>,
linux-doc@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: Re: [PATCH 3/3] gpio: msm: Add device tree and irqdomain support for gpio-msm-v2
Date: Wed, 22 May 2013 12:29:40 -0700 [thread overview]
Message-ID: <519D1CA4.9050506@codeaurora.org> (raw)
In-Reply-To: <20130521210627.GA599@codeaurora.org>
On 5/21/2013 2:06 PM, Stephen Boyd wrote:
>> diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
>> index 87d5670..f3c1978 100644
>> --- a/drivers/gpio/Kconfig
>> +++ b/drivers/gpio/Kconfig
>> @@ -165,7 +165,7 @@ config GPIO_MSM_V1
>>
>> config GPIO_MSM_V2
>> tristate "Qualcomm MSM GPIO v2"
>> - depends on GPIOLIB && ARCH_MSM
>> + depends on GPIOLIB && ARCH_MSM && OF
> This doesn't actually rely on ARCH_MSM anymore so I think we can
> drop that dependency.
Done.
>
>> help
>> Say yes here to support the GPIO interface on ARM v7 based
>> Qualcomm MSM chips. Most of the pins on the MSM can be
>> @@ -222,7 +229,6 @@ static void msm_gpio_update_dual_edge_pos(unsigned gpio)
>> else
>> set_gpio_bits(BIT(INTR_POL_CTL), GPIO_INTR_CFG(gpio));
>> val2 = readl(GPIO_IN_OUT(gpio)) & BIT(GPIO_IN);
>> - intstat = readl(GPIO_INTR_STATUS(gpio)) & BIT(INTR_STATUS);
>> if (intstat || val == val2)
> Looks like intstat is used uninitialized now?
Thanks for catching this. Will fix this.
>
>> +
>> +static int msm_gpio_probe(struct platform_device *pdev)
>> +{
>> + int i, irq, ret, ngpio;
>> + struct resource *res;
>> +
>> + msm_gpio.gpio_chip.label = pdev->name;
>> + msm_gpio.gpio_chip.dev = &pdev->dev;
>> + of_property_read_u32(pdev->dev.of_node, "ngpio", &ngpio);
> Fail probe if the property isn't there?
Done.
>
>> + msm_gpio.gpio_chip.ngpio = ngpio;
>> +
>> + res = platform_get_resource(&pdev->dev, IORESOURCE_MEM, 0);
>> + if (!res) {
>> + dev_err(&pdev->dev, "%s: no mem resource\n", __func__);
>> + return -EINVAL;
>> + }
>> +
>> + msm_tlmm_base = devm_ioremap_resource(pdev->dev, res);
>> + if (!msm_tlmm_base) {
>> + dev_err(&pdev->dev, "Couldn't allocate memory for msm tlmm base\n");
>> + return -ENOMEM;
>> + }
> devm_ioremap_resource() returns an ERR_PTR on failure, not NULL.
> Also, it already prints messages on errors so you can drop all the
> prints around this. Just do
>
> res = platform_get_resource(&pdev->dev, IORESOURCE_MEM, 0);
> msm_tlmm_base = devm_ioremap_resource(pdev->dev, res);
> if (IS_ERR(msm_tlmm_base))
> return ERR_PTR(msm_tlmm_base);
>
Done.
>> static int __init msm_gpio_init(void)
>> {
>> - int rc;
>> -
>> - rc = platform_driver_register(&msm_gpio_driver);
>> - if (!rc) {
>> - rc = platform_device_register(&msm_device_gpio);
>> - if (rc)
>> - platform_driver_unregister(&msm_gpio_driver);
>> - }
>> -
>> - return rc;
>> + return platform_driver_register(&msm_gpio_driver);
>> }
>>
>> static void __exit msm_gpio_exit(void)
>> {
>> - platform_device_unregister(&msm_device_gpio);
>> platform_driver_unregister(&msm_gpio_driver);
>> }
> You could use module_platform_driver here now too.
>
Done. Thanks for the comments.
Thanks,
Rohit Vaswani
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, hosted by The Linux Foundation
next prev parent reply other threads:[~2013-05-22 19:29 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-05-21 18:32 [PATCH 0/3] Cleanup MSM_GPIOMUX and add device-tree support for Rohit Vaswani
2013-05-21 18:32 ` [PATCH 1/3] ARM: msm: Remove gpiomux-v2 and re-organize MSM_GPIOMUX configs Rohit Vaswani
2013-05-30 17:53 ` Linus Walleij
2013-05-21 18:32 ` [PATCH 2/3] ARM: msm: Remove unused and unmapped MSM_TLMM_BASE for 8x60 Rohit Vaswani
2013-05-21 18:32 ` [PATCH 3/3] gpio: msm: Add device tree and irqdomain support for gpio-msm-v2 Rohit Vaswani
2013-05-21 21:06 ` Stephen Boyd
2013-05-22 19:29 ` Rohit Vaswani [this message]
2013-05-22 9:36 ` Stanimir Varbanov
2013-05-22 19:27 ` Rohit Vaswani
2013-05-30 17:54 ` [PATCH 0/3] Cleanup MSM_GPIOMUX and add device-tree support for Linus Walleij
-- strict thread matches above, loose matches on Subject: below --
2013-06-10 22:50 [PATCHv5 0/3] Cleanup MSM_GPIOMUX and add DT support for gpio-msm Rohit Vaswani
2013-06-10 22:50 ` [PATCH 3/3] gpio: msm: Add device tree and irqdomain support for gpio-msm-v2 Rohit Vaswani
2013-06-11 12:45 ` Grant Likely
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=519D1CA4.9050506@codeaurora.org \
--to=rvaswani@codeaurora.org \
--cc=bryanh@codeaurora.org \
--cc=davidb@codeaurora.org \
--cc=grant.likely@linaro.org \
--cc=linus.walleij@linaro.org \
--cc=linux-doc@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@arm.linux.org.uk \
--cc=rob.herring@calxeda.com \
--cc=rob@landley.net \
--cc=sboyd@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox