[PATCH 8/9] ARM: dove: add initial DT file for Globalscale D3Plug

Sebastian Hesselbarth
2013-08-12T18:48:02Z

This adds an initial DT file for the Globalscale D3Plug with Dove SoC.

Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
---
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/dove-d3plug.dts | 103 +++++++++++++++++++++++++++++++++++++
2 files changed, 104 insertions(+)
create mode 100644 arch/arm/boot/dts/dove-d3plug.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 984a997..ffb361c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -48,6 +48,7 @@ dtb-$(CONFIG_ARCH_DAVINCI) += da850-enbw-cmc.dtb \
dtb-$(CONFIG_ARCH_DOVE) += dove-cm-a510.dtb \
dove-cubox.dtb \
dove-d2plug.dtb \
+ dove-d3plug.dtb \
dove-dove-db.dtb
dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \
exynos4210-smdkv310.dtb \
diff --git a/arch/arm/boot/dts/dove-d3plug.dts b/arch/arm/boot/dts/dove-d3plug.dts
new file mode 100644
index 0000000..ead90eb
--- /dev/null
+++ b/arch/arm/boot/dts/dove-d3plug.dts
@@ -0,0 +1,103 @@
+/dts-v1/;
+
+#include "dove.dtsi"
+
+/ {
+ model = "Globalscale D3Plug";
+ compatible = "globalscale,d3plug", "marvell,dove";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x40000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/mmcblk0p2 rw rootwait";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&pmx_gpio_0 &pmx_gpio_1 &pmx_gpio_2>;
+ pinctrl-names = "default";
+
+ wlan-act {
+ label = "wlan-act";
+ gpios = <&gpio0 0 1>;
+ };
+
+ wlan-ap {
+ label = "wlan-ap";
+ gpios = <&gpio0 1 1>;
+ };
+
+ status {
+ label = "status";
+ gpios = <&gpio0 2 1>;
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb_power: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "USB Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio0 8 0>;
+ pinctrl-0 = <&pmx_gpio_8>;
+ pinctrl-names = "default";
+ };
+ };
+};
+
+&uart0 { status = "okay"; };
+&sata0 { status = "okay"; };
+&i2c0 { status = "okay"; };
+
+/* Samsung M8G2F eMMC */
+&sdio0 {
+ status = "okay";
+ non-removable;
+ bus-width = <4>;
+};
+
+/* Marvell SD8787 WLAN/BT */
+&sdio1 {
+ status = "okay";
+ non-removable;
+};
+
+&spi0 {
+ status = "okay";
+
+ /* spi0.0: 2M Flash Macronix MX25L1605D */
+ spi-flash@0 {
+ compatible = "st,m25l1605d";
+ spi-max-frequency = <86000000>;
+ reg = <0>;
+ };
+};
+
+&pcie {
+ status = "okay";
+ /* Fresco Logic USB3.0 xHCI controller */
+ pcie-port@0 {
+ status = "okay";
+ reset-gpios = <&gpio0 26 1>;
+ reset-delay-ms = <20>;
+ pinctrl-0 = <&pmx_camera_gpio>;
+ pinctrl-names = "default";
+ };
+ /* Mini-PCIe slot */
+ pcie-port@1 {
+ status = "okay";
+ reset-gpios = <&gpio0 25 1>;
+ };
+};
--
1.7.10.4