[PATCH 5/7] mtd: nand: davinci: move bindings under mtd

Ivan Khoronzhuk
2013-11-20T15:23:46Z

Move bindings under mtd. Do this in order to make davinci-nand
driver usable by keystone architecture.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
---
.../devicetree/bindings/arm/davinci/nand.txt | 46 --------------------
.../devicetree/bindings/mtd/davinci-nand.txt | 46 ++++++++++++++++++++
2 files changed, 46 insertions(+), 46 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/arm/davinci/nand.txt
create mode 100644 Documentation/devicetree/bindings/mtd/davinci-nand.txt

diff --git a/Documentation/devicetree/bindings/arm/davinci/nand.txt b/Documentation/devicetree/bindings/arm/davinci/nand.txt
deleted file mode 100644
index 3545ea7..0000000
--- a/Documentation/devicetree/bindings/arm/davinci/nand.txt
+++ /dev/null
@@ -1,46 +0,0 @@
-* Texas Instruments Davinci NAND
-
-This file provides information, what the device node for the
-davinci nand interface contain.
-
-Required properties:
-- compatible: "ti,davinci-nand";
-- reg : contain 2 offset/length values:
- - offset and length for the access window
- - offset and length for accessing the aemif control registers
-- ti,davinci-chipselect: Indicates on the davinci_nand driver which
- chipselect is used for accessing the nand.
-
-Recommended properties :
-- ti,davinci-mask-ale: mask for ale
-- ti,davinci-mask-cle: mask for cle
-- ti,davinci-mask-chipsel: mask for chipselect
-- ti,davinci-ecc-mode: ECC mode valid values for davinci driver:
- - "none"
- - "soft"
- - "hw"
-- ti,davinci-ecc-bits: used ECC bits, currently supported 1 or 4.
-- ti,davinci-nand-buswidth: buswidth 8 or 16
-- ti,davinci-nand-use-bbt: use flash based bad block table support.
-
-nand device bindings may contain additional sub-nodes describing
-partitions of the address space. See partition.txt for more detail.
-
-Example(da850 EVM ):
-nand_cs3@62000000 {
- compatible = "ti,davinci-nand";
- reg = <0x62000000 0x807ff
- 0x68000000 0x8000>;
- ti,davinci-chipselect = <1>;
- ti,davinci-mask-ale = <0>;
- ti,davinci-mask-cle = <0>;
- ti,davinci-mask-chipsel = <0>;
- ti,davinci-ecc-mode = "hw";
- ti,davinci-ecc-bits = <4>;
- ti,davinci-nand-use-bbt;
-
- partition@180000 {
- label = "ubifs";
- reg = <0x180000 0x7e80000>;
- };
-};
diff --git a/Documentation/devicetree/bindings/mtd/davinci-nand.txt b/Documentation/devicetree/bindings/mtd/davinci-nand.txt
new file mode 100644
index 0000000..3545ea7
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/davinci-nand.txt
@@ -0,0 +1,46 @@
+* Texas Instruments Davinci NAND
+
+This file provides information, what the device node for the
+davinci nand interface contain.
+
+Required properties:
+- compatible: "ti,davinci-nand";
+- reg : contain 2 offset/length values:
+ - offset and length for the access window
+ - offset and length for accessing the aemif control registers
+- ti,davinci-chipselect: Indicates on the davinci_nand driver which
+ chipselect is used for accessing the nand.
+
+Recommended properties :
+- ti,davinci-mask-ale: mask for ale
+- ti,davinci-mask-cle: mask for cle
+- ti,davinci-mask-chipsel: mask for chipselect
+- ti,davinci-ecc-mode: ECC mode valid values for davinci driver:
+ - "none"
+ - "soft"
+ - "hw"
+- ti,davinci-ecc-bits: used ECC bits, currently supported 1 or 4.
+- ti,davinci-nand-buswidth: buswidth 8 or 16
+- ti,davinci-nand-use-bbt: use flash based bad block table support.
+
+nand device bindings may contain additional sub-nodes describing
+partitions of the address space. See partition.txt for more detail.
+
+Example(da850 EVM ):
+nand_cs3@62000000 {
+ compatible = "ti,davinci-nand";
+ reg = <0x62000000 0x807ff
+ 0x68000000 0x8000>;
+ ti,davinci-chipselect = <1>;
+ ti,davinci-mask-ale = <0>;
+ ti,davinci-mask-cle = <0>;
+ ti,davinci-mask-chipsel = <0>;
+ ti,davinci-ecc-mode = "hw";
+ ti,davinci-ecc-bits = <4>;
+ ti,davinci-nand-use-bbt;
+
+ partition@180000 {
+ label = "ubifs";
+ reg = <0x180000 0x7e80000>;
+ };
+};
--
1.7.9.5