From: Boris BREZILLON <boris.brezillon@free-electrons.com>
To: Tim Niemeyer <tim.niemeyer@corscience.de>,
Jean-Jacques Hiblot <jjhiblot@traphandler.com>,
Robert Nelson <robertcnelson@gmail.com>
Cc: nicolas.ferre@atmel.com, linux-arm-kernel@lists.infradead.org,
dri-devel@lists.freedesktop.org, airlied@linux.ie,
robdclark@gmail.com, plagnioj@jcrosoft.com,
linux-kernel@vger.kernel.org
Subject: Re: [RFC 0/3] DRM driver for the ATMEL High end LCD controller
Date: Thu, 24 Apr 2014 14:14:04 +0200 [thread overview]
Message-ID: <5359000C.50005@free-electrons.com> (raw)
In-Reply-To: <1398267396.4295.59.camel@herbert.er.corscience.de>
Hi Tim,
On 23/04/2014 17:36, Tim Niemeyer wrote:
> Hi Jean-Jacques,
>
> Am Freitag, den 18.04.2014, 11:45 +0200 schrieb Jean-Jacques Hiblot:
>> Hi,
>>
>> this patch serie implements a simple DRM driver for the ATMEL High end LCD
>> controller found in the SAMA5 familly. It's based on the tilcdc driver.
>> It uses the cma_helper for memory and fbdev stuff.
>> Your comments are welcome !
> I applied your and Robert's patches on a 3.15-rc2 kernel and tried the
> framebuffer device on the sama5d31-ek. Seems to work.
>
>> Supported features:
>> * the base layer (the main framebuffer)
> Tested to show a little tux png, but it's appearing only after
> 'echo 0 > /sys/devices/ahb.1/apb.2/f0030000.hlcdc/graphics/fb0/rotate'
> is there missing some initializing?
Could you try to apply this http://code.bulix.org/f01kvh-86117 ?
Best Regards,
Boris
>
>> * a simple panel
>> * a backlight driver
> Tested to set brightness to 0, 20 and 255. Works.
>
> Thanks for your work.
>
> Best Regards
> Tim
>
>> * structure to 'easily' add other connectors (it comes from the tilcdc)
>>
>> On the todo list:
>> * support overlays as drm_planes
>> * support for the hardware cursor
>> * support for the SiI9022 HDMI connector (present on sama5d36ek)
>>
>>
>> Jean-Jacques Hiblot (3):
>> atmel: drm: added drm driver for the atmel hlcd controller
>> atmel: drm: dt: Added DT entry for the atmel hlcdc found in the sama5
>> atmel: dt: Add supports for the lcdc support on the sama5d36ek
>>
>> arch/arm/boot/dts/sama5d36ek.dts | 27 +-
>> arch/arm/boot/dts/sama5d3_lcd.dtsi | 11 +
>> drivers/gpu/drm/Kconfig | 2 +
>> drivers/gpu/drm/Makefile | 1 +
>> drivers/gpu/drm/atmel_hlcdc/Kconfig | 13 +
>> drivers/gpu/drm/atmel_hlcdc/Makefile | 12 +
>> drivers/gpu/drm/atmel_hlcdc/atmel_hlcdc.h | 771 +++++++++++++++++++++
>> .../gpu/drm/atmel_hlcdc/atmel_hlcdc_backlight.c | 92 +++
>> .../gpu/drm/atmel_hlcdc/atmel_hlcdc_backlight.h | 25 +
>> drivers/gpu/drm/atmel_hlcdc/atmel_hlcdc_crtc.c | 702 +++++++++++++++++++
>> drivers/gpu/drm/atmel_hlcdc/atmel_hlcdc_drv.c | 586 ++++++++++++++++
>> drivers/gpu/drm/atmel_hlcdc/atmel_hlcdc_drv.h | 124 ++++
>> drivers/gpu/drm/atmel_hlcdc/atmel_hlcdc_ovl.h | 190 +++++
>> drivers/gpu/drm/atmel_hlcdc/atmel_hlcdc_panel.c | 459 ++++++++++++
>> drivers/gpu/drm/atmel_hlcdc/atmel_hlcdc_panel.h | 28 +
>> 15 files changed, 3042 insertions(+), 1 deletion(-)
>> create mode 100644 drivers/gpu/drm/atmel_hlcdc/Kconfig
>> create mode 100644 drivers/gpu/drm/atmel_hlcdc/Makefile
>> create mode 100644 drivers/gpu/drm/atmel_hlcdc/atmel_hlcdc.h
>> create mode 100644 drivers/gpu/drm/atmel_hlcdc/atmel_hlcdc_backlight.c
>> create mode 100644 drivers/gpu/drm/atmel_hlcdc/atmel_hlcdc_backlight.h
>> create mode 100644 drivers/gpu/drm/atmel_hlcdc/atmel_hlcdc_crtc.c
>> create mode 100644 drivers/gpu/drm/atmel_hlcdc/atmel_hlcdc_drv.c
>> create mode 100644 drivers/gpu/drm/atmel_hlcdc/atmel_hlcdc_drv.h
>> create mode 100644 drivers/gpu/drm/atmel_hlcdc/atmel_hlcdc_ovl.h
>> create mode 100644 drivers/gpu/drm/atmel_hlcdc/atmel_hlcdc_panel.c
>> create mode 100644 drivers/gpu/drm/atmel_hlcdc/atmel_hlcdc_panel.h
>>
>> --
>> 1.9.1
>>
>>
>> _______________________________________________
>> linux-arm-kernel mailing list
>> linux-arm-kernel@lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>
--
Boris Brezillon, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
next prev parent reply other threads:[~2014-04-24 12:14 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-04-18 9:45 [RFC 0/3] DRM driver for the ATMEL High end LCD controller Jean-Jacques Hiblot
2014-04-18 9:45 ` [RFC 1/3] atmel: drm: added drm driver for the atmel hlcd controller Jean-Jacques Hiblot
2014-04-18 13:21 ` Boris BREZILLON
2014-04-18 14:31 ` Robert Nelson
2014-04-19 19:03 ` Jean-Jacques Hiblot
2014-04-28 19:22 ` Boris BREZILLON
2014-05-01 6:34 ` Jean-Jacques Hiblot
2014-04-18 9:45 ` [RFC 2/3] atmel: drm: dt: Added DT entry for the atmel hlcdc found in the sama5 Jean-Jacques Hiblot
2014-04-18 9:45 ` [RFC 3/3] atmel: dt: Add supports for the lcdc support on the sama5d36ek Jean-Jacques Hiblot
2014-04-18 14:48 ` Robert Nelson
2014-04-19 19:07 ` Jean-Jacques Hiblot
2014-04-18 13:37 ` [RFC 0/3] DRM driver for the ATMEL High end LCD controller Boris BREZILLON
2014-04-23 15:36 ` Tim Niemeyer
2014-04-24 12:14 ` Boris BREZILLON [this message]
2014-04-24 12:46 ` Tim Niemeyer
2014-04-24 16:59 ` Jean-Jacques Hiblot
2014-04-30 14:31 ` Jean-Jacques Hiblot
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=5359000C.50005@free-electrons.com \
--to=boris.brezillon@free-electrons.com \
--cc=airlied@linux.ie \
--cc=dri-devel@lists.freedesktop.org \
--cc=jjhiblot@traphandler.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=nicolas.ferre@atmel.com \
--cc=plagnioj@jcrosoft.com \
--cc=robdclark@gmail.com \
--cc=robertcnelson@gmail.com \
--cc=tim.niemeyer@corscience.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox