* [PATCH] nand: davinci: add support for 4K page size nand devices
@ 2014-05-08 22:31 Ivan Khoronzhuk
2014-05-12 15:21 ` Santosh Shilimkar
0 siblings, 1 reply; 3+ messages in thread
From: Ivan Khoronzhuk @ 2014-05-08 22:31 UTC (permalink / raw)
To: Brian Norris, David Woodhouse
Cc: Santosh Shilimkar, grygorii.strashko, Murali Karicheri, linux-mtd,
linux-kernel, ivan.khoronzhuk
From: Sandeep Paulraj <s-paulraj@ti.com>
It is needed for k2l keystone2 EVM which uses NAND flash with 4K page
size, hence add support for 4K page size nand devices.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
---
Based on l2-mtd/master
drivers/mtd/nand/davinci_nand.c | 41 ++++++++++++++++++++++++++++++-----------
1 file changed, 30 insertions(+), 11 deletions(-)
diff --git a/drivers/mtd/nand/davinci_nand.c b/drivers/mtd/nand/davinci_nand.c
index b922c8e..24a5769 100644
--- a/drivers/mtd/nand/davinci_nand.c
+++ b/drivers/mtd/nand/davinci_nand.c
@@ -520,6 +520,31 @@ static struct nand_ecclayout hwecc4_2048 = {
},
};
+/* An ECC layout for using 4-bit ECC with large-page (4096bytes) flash,
+ * storing ten ECC bytes plus the manufacturer's bad block marker byte,
+ * and not overlapping the default BBT markers.
+ */
+static struct nand_ecclayout hwecc4_4096 __initconst = {
+ .eccbytes = 80,
+ .eccpos = {
+ /* at the end of spare sector */
+ 48, 49, 50, 51, 52, 53, 54, 55, 56, 57,
+ 58, 59, 60, 61, 62, 63, 64, 65, 66, 67,
+ 68, 69, 70, 71, 72, 73, 74, 75, 76, 77,
+ 78, 79, 80, 81, 82, 83, 84, 85, 86, 87,
+ 88, 89, 90, 91, 92, 93, 94, 95, 96, 97,
+ 98, 99, 100, 101, 102, 103, 104, 105, 106, 107,
+ 108, 109, 110, 111, 112, 113, 114, 115, 116, 117,
+ 118, 119, 120, 121, 122, 123, 124, 125, 126, 127,
+ },
+ .oobfree = {
+ /* 2 bytes at offset 0 hold manufacturer badblock markers */
+ {.offset = 2, .length = 46, },
+ /* 5 bytes at offset 8 hold BBT markers */
+ /* 8 bytes at offset 16 hold JFFS2 clean markers */
+ },
+};
+
#if defined(CONFIG_OF)
static const struct of_device_id davinci_nand_of_match[] = {
{.compatible = "ti,davinci-nand", },
@@ -796,18 +821,12 @@ static int nand_davinci_probe(struct platform_device *pdev)
info->chip.ecc.mode = NAND_ECC_HW_OOB_FIRST;
goto syndrome_done;
}
+ if (chunks == 8) {
+ info->ecclayout = hwecc4_4096;
+ info->chip.ecc.mode = NAND_ECC_HW_OOB_FIRST;
+ goto syndrome_done;
+ }
- /* 4KiB page chips are not yet supported. The eccpos from
- * nand_ecclayout cannot hold 80 bytes and change to eccpos[]
- * breaks userspace ioctl interface with mtd-utils. Once we
- * resolve this issue, NAND_ECC_HW_OOB_FIRST mode can be used
- * for the 4KiB page chips.
- *
- * TODO: Note that nand_ecclayout has now been expanded and can
- * hold plenty of OOB entries.
- */
- dev_warn(&pdev->dev, "no 4-bit ECC support yet "
- "for 4KiB-page NAND\n");
ret = -EIO;
goto err;
--
1.8.3.2
^ permalink raw reply related [flat|nested] 3+ messages in thread* Re: [PATCH] nand: davinci: add support for 4K page size nand devices
2014-05-08 22:31 [PATCH] nand: davinci: add support for 4K page size nand devices Ivan Khoronzhuk
@ 2014-05-12 15:21 ` Santosh Shilimkar
2014-05-14 23:33 ` Ivan Khoronzhuk
0 siblings, 1 reply; 3+ messages in thread
From: Santosh Shilimkar @ 2014-05-12 15:21 UTC (permalink / raw)
To: Ivan Khoronzhuk, Brian Norris, David Woodhouse
Cc: grygorii.strashko, Murali Karicheri, linux-mtd, linux-kernel
On Thursday 08 May 2014 06:31 PM, Ivan Khoronzhuk wrote:
> From: Sandeep Paulraj <s-paulraj@ti.com>
>
> It is needed for k2l keystone2 EVM which uses NAND flash with 4K page
> size, hence add support for 4K page size nand devices.
>
> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
> ---
>
> Based on l2-mtd/master
>
> drivers/mtd/nand/davinci_nand.c | 41 ++++++++++++++++++++++++++++++-----------
> 1 file changed, 30 insertions(+), 11 deletions(-)
>
> diff --git a/drivers/mtd/nand/davinci_nand.c b/drivers/mtd/nand/davinci_nand.c
> index b922c8e..24a5769 100644
> --- a/drivers/mtd/nand/davinci_nand.c
> +++ b/drivers/mtd/nand/davinci_nand.c
> @@ -520,6 +520,31 @@ static struct nand_ecclayout hwecc4_2048 = {
> },
> };
>
> +/* An ECC layout for using 4-bit ECC with large-page (4096bytes) flash,
> + * storing ten ECC bytes plus the manufacturer's bad block marker byte,
> + * and not overlapping the default BBT markers.
> + */
Comment style ....
/*
*
*/
> +static struct nand_ecclayout hwecc4_4096 __initconst = {
> + .eccbytes = 80,
> + .eccpos = {
> + /* at the end of spare sector */
> + 48, 49, 50, 51, 52, 53, 54, 55, 56, 57,
> + 58, 59, 60, 61, 62, 63, 64, 65, 66, 67,
> + 68, 69, 70, 71, 72, 73, 74, 75, 76, 77,
> + 78, 79, 80, 81, 82, 83, 84, 85, 86, 87,
> + 88, 89, 90, 91, 92, 93, 94, 95, 96, 97,
> + 98, 99, 100, 101, 102, 103, 104, 105, 106, 107,
> + 108, 109, 110, 111, 112, 113, 114, 115, 116, 117,
> + 118, 119, 120, 121, 122, 123, 124, 125, 126, 127,
> + },
> + .oobfree = {
> + /* 2 bytes at offset 0 hold manufacturer badblock markers */
> + {.offset = 2, .length = 46, },
> + /* 5 bytes at offset 8 hold BBT markers */
> + /* 8 bytes at offset 16 hold JFFS2 clean markers */
> + },
> +};
> +
> #if defined(CONFIG_OF)
> static const struct of_device_id davinci_nand_of_match[] = {
> {.compatible = "ti,davinci-nand", },
> @@ -796,18 +821,12 @@ static int nand_davinci_probe(struct platform_device *pdev)
> info->chip.ecc.mode = NAND_ECC_HW_OOB_FIRST;
> goto syndrome_done;
> }
> + if (chunks == 8) {
May be use some meaning macros instead of magic value '8'
> + info->ecclayout = hwecc4_4096;
> + info->chip.ecc.mode = NAND_ECC_HW_OOB_FIRST;
> + goto syndrome_done;
> + }
>
> - /* 4KiB page chips are not yet supported. The eccpos from
> - * nand_ecclayout cannot hold 80 bytes and change to eccpos[]
> - * breaks userspace ioctl interface with mtd-utils. Once we
> - * resolve this issue, NAND_ECC_HW_OOB_FIRST mode can be used
> - * for the 4KiB page chips.
> - *
> - * TODO: Note that nand_ecclayout has now been expanded and can
> - * hold plenty of OOB entries.
> - */
> - dev_warn(&pdev->dev, "no 4-bit ECC support yet "
> - "for 4KiB-page NAND\n");
> ret = -EIO;
> goto err;
>
>
^ permalink raw reply [flat|nested] 3+ messages in thread* Re: [PATCH] nand: davinci: add support for 4K page size nand devices
2014-05-12 15:21 ` Santosh Shilimkar
@ 2014-05-14 23:33 ` Ivan Khoronzhuk
0 siblings, 0 replies; 3+ messages in thread
From: Ivan Khoronzhuk @ 2014-05-14 23:33 UTC (permalink / raw)
To: Santosh Shilimkar, Brian Norris, David Woodhouse
Cc: grygorii.strashko, Murali Karicheri, linux-mtd, linux-kernel
On 05/12/2014 06:21 PM, Santosh Shilimkar wrote:
> On Thursday 08 May 2014 06:31 PM, Ivan Khoronzhuk wrote:
>> From: Sandeep Paulraj <s-paulraj@ti.com>
>>
>> It is needed for k2l keystone2 EVM which uses NAND flash with 4K page
>> size, hence add support for 4K page size nand devices.
>>
>> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
>> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
>> ---
>>
>> Based on l2-mtd/master
>>
>> drivers/mtd/nand/davinci_nand.c | 41 ++++++++++++++++++++++++++++++-----------
>> 1 file changed, 30 insertions(+), 11 deletions(-)
>>
>> diff --git a/drivers/mtd/nand/davinci_nand.c b/drivers/mtd/nand/davinci_nand.c
>> index b922c8e..24a5769 100644
>> --- a/drivers/mtd/nand/davinci_nand.c
>> +++ b/drivers/mtd/nand/davinci_nand.c
>> @@ -520,6 +520,31 @@ static struct nand_ecclayout hwecc4_2048 = {
>> },
>> };
>>
>> +/* An ECC layout for using 4-bit ECC with large-page (4096bytes) flash,
>> + * storing ten ECC bytes plus the manufacturer's bad block marker byte,
>> + * and not overlapping the default BBT markers.
>> + */
> Comment style ....
> /*
> *
> */
yes
>> +static struct nand_ecclayout hwecc4_4096 __initconst = {
>> + .eccbytes = 80,
>> + .eccpos = {
>> + /* at the end of spare sector */
>> + 48, 49, 50, 51, 52, 53, 54, 55, 56, 57,
>> + 58, 59, 60, 61, 62, 63, 64, 65, 66, 67,
>> + 68, 69, 70, 71, 72, 73, 74, 75, 76, 77,
>> + 78, 79, 80, 81, 82, 83, 84, 85, 86, 87,
>> + 88, 89, 90, 91, 92, 93, 94, 95, 96, 97,
>> + 98, 99, 100, 101, 102, 103, 104, 105, 106, 107,
>> + 108, 109, 110, 111, 112, 113, 114, 115, 116, 117,
>> + 118, 119, 120, 121, 122, 123, 124, 125, 126, 127,
>> + },
>> + .oobfree = {
>> + /* 2 bytes at offset 0 hold manufacturer badblock markers */
>> + {.offset = 2, .length = 46, },
>> + /* 5 bytes at offset 8 hold BBT markers */
>> + /* 8 bytes at offset 16 hold JFFS2 clean markers */
>> + },
>> +};
>> +
>> #if defined(CONFIG_OF)
>> static const struct of_device_id davinci_nand_of_match[] = {
>> {.compatible = "ti,davinci-nand", },
>> @@ -796,18 +821,12 @@ static int nand_davinci_probe(struct platform_device *pdev)
>> info->chip.ecc.mode = NAND_ECC_HW_OOB_FIRST;
>> goto syndrome_done;
>> }
>> + if (chunks == 8) {
> May be use some meaning macros instead of magic value '8'
It just continues style used in the code:
if (chunks == 1) {
...
if (chunks == 4) {
...
if (chunks == 8) {
...
>
>> + info->ecclayout = hwecc4_4096;
>> + info->chip.ecc.mode = NAND_ECC_HW_OOB_FIRST;
>> + goto syndrome_done;
>> + }
>>
>> - /* 4KiB page chips are not yet supported. The eccpos from
>> - * nand_ecclayout cannot hold 80 bytes and change to eccpos[]
>> - * breaks userspace ioctl interface with mtd-utils. Once we
>> - * resolve this issue, NAND_ECC_HW_OOB_FIRST mode can be used
>> - * for the 4KiB page chips.
>> - *
>> - * TODO: Note that nand_ecclayout has now been expanded and can
>> - * hold plenty of OOB entries.
>> - */
>> - dev_warn(&pdev->dev, "no 4-bit ECC support yet "
>> - "for 4KiB-page NAND\n");
>> ret = -EIO;
>> goto err;
>>
>>
--
Regards,
Ivan Khoronzhuk
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2014-05-14 23:33 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2014-05-08 22:31 [PATCH] nand: davinci: add support for 4K page size nand devices Ivan Khoronzhuk
2014-05-12 15:21 ` Santosh Shilimkar
2014-05-14 23:33 ` Ivan Khoronzhuk
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox