Re: [PATCH v1.2 17/16] arcmsr: fixed calling scsi_scan_host after all initialization done

[Tomas Henzl <thenzl@redhat.com>]

On 05/14/2014 01:55 PM, ching wrote:
> From: Ching<ching2048@areca.com.tw>
>
> This is a new patch after patch v1.1 series.
>
> Fixed calling scsi_scan_host until all initialization are done.
> And fixed error path free allocated resource.
>
> Signed-off-by: Ching<ching2048@areca.com.tw>
> ---
>
> diff -uprN a/drivers/scsi/arcmsr/arcmsr_hba.c b/drivers/scsi/arcmsr/arcmsr_hba.c
> --- a/drivers/scsi/arcmsr/arcmsr_hba.c	2014-05-08 17:45:34.000000000 +0800
> +++ b/drivers/scsi/arcmsr/arcmsr_hba.c	2014-05-14 18:29:30.000000000 +0800
> @@ -112,6 +112,7 @@ static void arcmsr_hbaD_message_isr(stru
>  static void arcmsr_hardware_reset(struct AdapterControlBlock *acb);
>  static const char *arcmsr_info(struct Scsi_Host *);
>  static irqreturn_t arcmsr_interrupt(struct AdapterControlBlock *acb);
> +static void arcmsr_free_irq(struct pci_dev *, struct AdapterControlBlock *);
>  static int arcmsr_adjust_disk_queue_depth(struct scsi_device *sdev,
>  					  int queue_depth, int reason)
>  {
> @@ -778,12 +779,11 @@ static int arcmsr_probe(struct pci_dev *
>  	}
>  	error = scsi_add_host(host, &pdev->dev);
>  	if(error){
> -		goto RAID_controller_stop;
> +		goto free_ccb_pool;
>  	}
>  	if (arcmsr_request_irq(pdev, acb) == ARC_FAILURE)
>  		goto scsi_host_remove;
>  	arcmsr_iop_init(acb);
> -    	scsi_scan_host(host);
>  	INIT_WORK(&acb->arcmsr_do_message_isr_bh, arcmsr_message_isr_bh_fn);
>  	atomic_set(&acb->rq_map_token, 16);
>  	atomic_set(&acb->ante_token_value, 16);
> @@ -795,13 +795,17 @@ static int arcmsr_probe(struct pci_dev *
>  	add_timer(&acb->eternal_timer);
>  	if(arcmsr_alloc_sysfs_attr(acb))
>  		goto out_free_sysfs;
> +    	scsi_scan_host(host);
>  	return 0;
>  out_free_sysfs:
> -scsi_host_remove:
> -	scsi_remove_host(host);
> -RAID_controller_stop:
> +	del_timer_sync(&acb->eternal_timer);
> + 	flush_work(&acb->arcmsr_do_message_isr_bh);

In your driver you use both flush_work(struct work_struct *) and flush_scheduled_work(),
the second form is used used to flush the shared workqueue. 
That said (and I think you use just one queue) you should decide which one is correct.
In my previous mail I have asked about flush_work because i have it seen elsewhere in
your code, now I've noticed the use of schedule_work and that means that you are using the global wq.
 

>  	arcmsr_stop_adapter_bgrb(acb);
>  	arcmsr_flush_adapter_cache(acb);
> +	arcmsr_free_irq(pdev, acb);
> +scsi_host_remove:
> +	scsi_remove_host(host);
> +free_ccb_pool:
>  	arcmsr_free_ccb_pool(acb);
>  free_hbb_mu:
>  	arcmsr_free_mu(acb);
>
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html