From: Kukjin Kim <kgene.kim@samsung.com>
To: Vivek Gautam <gautam.vivek@samsung.com>
Cc: linux-samsung-soc@vger.kernel.org, linux-usb@vger.kernel.org,
devicetree@vger.kernel.org, kgene.kim@samsung.com,
gregkh@linuxfoundation.org, t.figa@samsung.com,
jg1.han@samsung.com, linux-kernel@vger.kernel.org, balbi@ti.com,
kishon@ti.com, robh+dt@kernel.org,
linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH v6 0/8] Enable USB 3.0 support on Exynos5 systems
Date: Fri, 16 May 2014 06:53:48 +0900 [thread overview]
Message-ID: <5375376C.90306@samsung.com> (raw)
In-Reply-To: <1400076070-12456-1-git-send-email-gautam.vivek@samsung.com>
On 05/14/14 23:01, Vivek Gautam wrote:
> From: Vivek gautam<gautam.vivek@samsung.com>
>
> Based on 'for-next' branch of Kgene's linux-samsung tree;
> along with dts patches for USB 2.0 phy[1], and Exynos5800 [2].
> Also based on the latest USB 3.0 DRD phy driver patches posted [3].
>
> Changes from v5:
> - Added node reference names for new boards.
> - Removed 'samsung,pmu-offset' porperty from nodes, since with latest driver
> bindings this is not required.
> - Added aliase nodes in Exynos5420 to facilitate latest driver bindings.
> - Added patch to add VBUS regulator for peach-pi board also.
> - Dropped patches removing older usb-phy driver:
> usb-phy: samsung-usb3: Remove older phy-samsung-usb3 driver
> ARM: exynos_defconfig: Remove SAMSUNG_USB3PHY config
> as appeared in V5 version of this series.
> Will post them separately after the new driver is merged.
>
> [1] http://www.spinics.net/lists/linux-samsung-soc/msg30494.html
> [2] http://comments.gmane.org/gmane.linux.kernel.samsung-soc/31133
> [3] https://lkml.org/lkml/2014/5/13/285
>
> Vivek Gautam (7):
> ARM: dts: exynos5420: Enable support for USB 3.0 PHY controller
> ARM: dts: exynos5420: Enable support for DWC3 controller
> ARM: dts: exynos5250: Enable support for generic USB DRD phy
> ARM: dts: exynos5250: Update DWC3 usb controller to use new phy
> driver
> ARM: dts: exynos5250-snow: Add Vbus regulator for USB 3.0
> ARM: dts: exynos5420-peach-pit: Add Vbus regulator for USB 3.0
> ARM: dts: exynos5420-smdk5420: Add Vbus regulator for USB 3.0
>
> Vivek gautam (1):
should be same guy.
Vivek Gautam ;-)
> ARM: dts: exynos5800-peach-pi: Add Vbus regulator for USB 3.0
>
> arch/arm/boot/dts/exynos5250-snow.dts | 22 ++++++++++++
> arch/arm/boot/dts/exynos5250.dtsi | 20 +++++------
> arch/arm/boot/dts/exynos5420-peach-pit.dts | 46 ++++++++++++++++++++++++
> arch/arm/boot/dts/exynos5420-smdk5420.dts | 46 ++++++++++++++++++++++++
> arch/arm/boot/dts/exynos5420.dtsi | 54 ++++++++++++++++++++++++++++
> arch/arm/boot/dts/exynos5800-peach-pi.dts | 46 ++++++++++++++++++++++++
> 6 files changed, 222 insertions(+), 12 deletions(-)
>
Looks good to me.
Applied 1 to 4 patches, but for others 5 to 8 I need to get any review
or ack from dt guys.
Thanks,
Kukjin
prev parent reply other threads:[~2014-05-15 21:53 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-05-14 14:01 [PATCH v6 0/8] Enable USB 3.0 support on Exynos5 systems Vivek Gautam
2014-05-14 14:01 ` [PATCH v6 1/8] ARM: dts: exynos5420: Enable support for USB 3.0 PHY controller Vivek Gautam
2014-05-14 14:01 ` [PATCH v6 2/8] ARM: dts: exynos5420: Enable support for DWC3 controller Vivek Gautam
2014-05-14 14:01 ` [PATCH v6 3/8] ARM: dts: exynos5250: Enable support for generic USB DRD phy Vivek Gautam
2014-05-14 14:01 ` [PATCH v6 4/8] ARM: dts: exynos5250: Update DWC3 usb controller to use new phy driver Vivek Gautam
2014-05-14 14:01 ` [PATCH v6 5/8] ARM: dts: exynos5250-snow: Add Vbus regulator for USB 3.0 Vivek Gautam
2014-05-19 11:26 ` Kukjin Kim
2014-05-14 14:01 ` [PATCH v6 6/8] ARM: dts: exynos5420-peach-pit: " Vivek Gautam
2014-05-14 14:01 ` [PATCH v6 7/8] ARM: dts: exynos5420-smdk5420: " Vivek Gautam
2014-05-14 14:01 ` [PATCH v6 8/8] ARM: dts: exynos5800-peach-pi: " Vivek Gautam
2014-05-15 21:53 ` Kukjin Kim [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=5375376C.90306@samsung.com \
--to=kgene.kim@samsung.com \
--cc=balbi@ti.com \
--cc=devicetree@vger.kernel.org \
--cc=gautam.vivek@samsung.com \
--cc=gregkh@linuxfoundation.org \
--cc=jg1.han@samsung.com \
--cc=kishon@ti.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-samsung-soc@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=t.figa@samsung.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).