From: Giuseppe CAVALLARO <peppe.cavallaro@st.com>
To: Chen-Yu Tsai <wens@csie.org>, Ley Foon Tan <lftan@altera.com>
Cc: netdev <netdev@vger.kernel.org>,
linux-kernel <linux-kernel@vger.kernel.org>,
"David S. Miller" <davem@davemloft.net>, <lftan.linux@gmail.com>,
Vince Bridgers <vbridger@altera.com>
Subject: Re: [PATCH] net: stmmac: add dcrs parameter
Date: Mon, 25 Aug 2014 14:51:08 +0200 [thread overview]
Message-ID: <53FB313C.9010808@st.com> (raw)
In-Reply-To: <CAGb2v65fi=D_TQBSospft4T5OrBCj5TwQfgtkX=11M8TWFftYg@mail.gmail.com>
On 8/25/2014 2:34 PM, Chen-Yu Tsai wrote:
> Hi,
>
> On Mon, Aug 25, 2014 at 7:50 PM, Ley Foon Tan <lftan@altera.com> wrote:
>> This patch add the option to enable DCRS bit in GMAC control register.
>> Default is disabled if snps,dcrs is not defined.
>>
>> For MII, Carrier Sense (CRS) must be asserted during transmission
>> whereas in RGMII, CRS is not. RGMII does not provide a way to signal
>> loss of carrier during a transmission.
>>
>> When DCRS bit set high in control register, the MAC transmitter
>> ignore the (G)MII Carrier Sense signal during frame transmission
>> in the half-duplex mode. This request results in no errors generated
>> because of Loss of Carrier or No Carrier during such transmission.
>>
>> Signed-off-by: Ley Foon Tan <lftan@altera.com>
>> ---
>> Documentation/devicetree/bindings/net/stmmac.txt | 4 ++++
>> drivers/net/ethernet/stmicro/stmmac/common.h | 3 ++-
>> drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c | 4 +++-
>> drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 3 ++-
>> drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c | 2 ++
>> include/linux/stmmac.h | 1 +
>> 6 files changed, 14 insertions(+), 3 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt
>> index 9b03c57..a68e720 100644
>> --- a/Documentation/devicetree/bindings/net/stmmac.txt
>> +++ b/Documentation/devicetree/bindings/net/stmmac.txt
>> @@ -39,6 +39,10 @@ Optional properties:
>> further clocks may be specified in derived bindings.
>> - clock-names: One name for each entry in the clocks property, the
>> first one should be "stmmaceth".
>> +- snps,dcrs: Enable DCRS bit in GMAC control register. This DCRS bit makes the
>> + MAC transmitter ignore the (G)MII CRS signal during frame transmission
>> + in the half-duplex mode. This request results in no errors generated
>
> Since you know this is only required under (G)MII, could you not re-use
> the "phy-mode" property, instead of adding another one?
>
> Better yet, use the "interface" field in the platform data. This way you'll
> fix non-DT devices as well. You could then avoid touching the platform driver,
> and just modify the driver core.
yes this is what I asked. Thx ChenYu for the this detail.
Ley Foon Tan, could you do that? Let me know
peppe
>
>
> Cheers
> ChenYu
>
>> + because of Loss of Carrier or No Carrier during such transmission.
>>
>> Examples:
>>
>> diff --git a/drivers/net/ethernet/stmicro/stmmac/common.h b/drivers/net/ethernet/stmicro/stmmac/common.h
>> index de507c3..9abe221 100644
>> --- a/drivers/net/ethernet/stmicro/stmmac/common.h
>> +++ b/drivers/net/ethernet/stmicro/stmmac/common.h
>> @@ -445,10 +445,11 @@ struct mac_device_info {
>> int multicast_filter_bins;
>> int unicast_filter_entries;
>> int mcast_bits_log2;
>> + int dcrs;
>> };
>>
>> struct mac_device_info *dwmac1000_setup(void __iomem *ioaddr, int mcbins,
>> - int perfect_uc_entries);
>> + int perfect_uc_entries, int dcrs);
>> struct mac_device_info *dwmac100_setup(void __iomem *ioaddr);
>>
>> void stmmac_set_mac_addr(void __iomem *ioaddr, u8 addr[6],
>> diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c b/drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c
>> index d8ef187..924d450 100644
>> --- a/drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c
>> +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c
>> @@ -37,6 +37,7 @@ static void dwmac1000_core_init(struct mac_device_info *hw, int mtu)
>> void __iomem *ioaddr = hw->pcsr;
>> u32 value = readl(ioaddr + GMAC_CONTROL);
>> value |= GMAC_CORE_INIT;
>> + value |= hw->dcrs;
>> if (mtu > 1500)
>> value |= GMAC_CONTROL_2K;
>> if (mtu > 2000)
>> @@ -409,7 +410,7 @@ static const struct stmmac_ops dwmac1000_ops = {
>> };
>>
>> struct mac_device_info *dwmac1000_setup(void __iomem *ioaddr, int mcbins,
>> - int perfect_uc_entries)
>> + int perfect_uc_entries, int dcrs)
>> {
>> struct mac_device_info *mac;
>> u32 hwid = readl(ioaddr + GMAC_VERSION);
>> @@ -422,6 +423,7 @@ struct mac_device_info *dwmac1000_setup(void __iomem *ioaddr, int mcbins,
>> mac->multicast_filter_bins = mcbins;
>> mac->unicast_filter_entries = perfect_uc_entries;
>> mac->mcast_bits_log2 = 0;
>> + mac->dcrs = dcrs;
>>
>> if (mac->multicast_filter_bins)
>> mac->mcast_bits_log2 = ilog2(mac->multicast_filter_bins);
>> diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
>> index 08addd6..bf35b19 100644
>> --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
>> +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
>> @@ -2600,7 +2600,8 @@ static int stmmac_hw_init(struct stmmac_priv *priv)
>> priv->dev->priv_flags |= IFF_UNICAST_FLT;
>> mac = dwmac1000_setup(priv->ioaddr,
>> priv->plat->multicast_filter_bins,
>> - priv->plat->unicast_filter_entries);
>> + priv->plat->unicast_filter_entries,
>> + priv->plat->dcrs);
>> } else {
>> mac = dwmac100_setup(priv->ioaddr);
>> }
>> diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
>> index bb524a9..07f895f 100644
>> --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
>> +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
>> @@ -227,6 +227,8 @@ static int stmmac_probe_config_dt(struct platform_device *pdev,
>> pr_warn("force_sf_dma_mode is ignored if force_thresh_dma_mode is set.");
>> }
>>
>> + plat->dcrs = of_property_read_bool(np, "snps,dcrs");
>> +
>> return 0;
>> }
>> #else
>> diff --git a/include/linux/stmmac.h b/include/linux/stmmac.h
>> index cd63851..6367f42 100644
>> --- a/include/linux/stmmac.h
>> +++ b/include/linux/stmmac.h
>> @@ -114,6 +114,7 @@ struct plat_stmmacenet_data {
>> int maxmtu;
>> int multicast_filter_bins;
>> int unicast_filter_entries;
>> + int dcrs;
>> void (*fix_mac_speed)(void *priv, unsigned int speed);
>> void (*bus_setup)(void __iomem *ioaddr);
>> void *(*setup)(struct platform_device *pdev);
>> --
>> 1.8.2.1
>>
>> --
>> To unsubscribe from this list: send the line "unsubscribe netdev" in
>> the body of a message to majordomo@vger.kernel.org
>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
>
next prev parent reply other threads:[~2014-08-25 12:51 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-08-25 11:50 [PATCH] net: stmmac: add dcrs parameter Ley Foon Tan
2014-08-25 12:23 ` Giuseppe CAVALLARO
2014-08-25 12:34 ` Chen-Yu Tsai
2014-08-25 12:51 ` Giuseppe CAVALLARO [this message]
2014-08-25 15:10 ` Vince Bridgers
2014-08-26 5:38 ` Giuseppe CAVALLARO
2014-08-26 12:35 ` Vince Bridgers
2014-08-26 13:20 ` Giuseppe CAVALLARO
2014-08-27 1:27 ` Ley Foon Tan
2014-08-27 2:36 ` Chen-Yu Tsai
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=53FB313C.9010808@st.com \
--to=peppe.cavallaro@st.com \
--cc=davem@davemloft.net \
--cc=lftan.linux@gmail.com \
--cc=lftan@altera.com \
--cc=linux-kernel@vger.kernel.org \
--cc=netdev@vger.kernel.org \
--cc=vbridger@altera.com \
--cc=wens@csie.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox