From: Pramod Gurav <pramod.gurav@smartplayin.com>
To: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>,
linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org, kernel@stlinux.com
Cc: Srinivas Kandagatla <srinivas.kandagatla@gmail.com>,
Srinivas Kandagatla <srinivas.kandagatla@linaro.com>,
Maxime Coquelin <maxime.coquelin@st.com>,
Patrice Chotard <patrice.chotard@st.com>,
Linus Walleij <linus.walleij@linaro.org>,
Bjorn Andersson <bjorn.andersson@sonymobile.com>
Subject: Re: [PATCH] pinctrl: st: Add remove function and remove gpio_chip on failure
Date: Fri, 05 Sep 2014 10:18:48 +0530 [thread overview]
Message-ID: <540940B0.5090000@smartplayin.com> (raw)
In-Reply-To: <5408AA8C.7040100@linaro.org>
Hi Srini,
Thanks for review.
On 04-09-2014 11:38 PM, Srinivas Kandagatla wrote:
> Pramod,
> sorry for delay in reply as I was travelling, still in Jet lag.
>> Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
>> ---
>> drivers/pinctrl/pinctrl-st.c | 25 +++++++++++++++++++++++++
>> 1 files changed, 25 insertions(+), 0 deletions(-)
>>
>> diff --git a/drivers/pinctrl/pinctrl-st.c b/drivers/pinctrl/pinctrl-st.c
>> index 5475374..9296845 100644
>> --- a/drivers/pinctrl/pinctrl-st.c
>> +++ b/drivers/pinctrl/pinctrl-st.c
>> @@ -1517,6 +1517,7 @@ static int st_gpiolib_register_bank(struct st_pinctrl *info,
>> 0, handle_simple_irq,
>> IRQ_TYPE_LEVEL_LOW);
>> if (err) {
>> + gpiochip_remove(&bank->gpio_chip);
> This change-set looks good.
> IMO, you can send a patch for this change set.
Will resend just this.
>
>> dev_info(dev, "could not add irqchip\n");
>> return err;
>> }
>> @@ -1685,6 +1686,29 @@ static int st_pctl_probe(struct platform_device *pdev)
>> return 0;
>> }
>>
>
>> +static int st_pctl_remove(struct platform_device *pdev)
>> +{
> Ideally this driver will not be removed, as other drivers depend on
> this, even the serial.
>
> so I see no big achievement in adding the remove functionality, as this
> is going to be a dead code and would never be tested.
>
>> + struct st_pinctrl *info = platform_get_drvdata(pdev);
>> + struct device_node *np = pdev->dev.of_node;
>> + struct device_node *child;
>> + struct gpio_chip gpio_chip;
>> + int bank = 0;
>> +
>
>> + if (info->nbanks) {
>> + for_each_child_of_node(np, child) {
>> + if (of_property_read_bool(child, "gpio-controller")) {
> We should not re-parse the DT nodes once we are done with it in the probe.
Thanks. :)
>
>> + gpio_chip = info->banks[bank].gpio_chip;
>> + gpiochip_remove(&gpio_chip);
>> + bank++;
>> + }
>> + }
>> + }
>> +
>
> I think the logic is very simple:
>
> while (nbanks--)
> gpiochip_remove(&info->banks[bank++].gpio_chip))
Thanks again. Remove is not needed hence will not do this. But good know.
>
>
> thanks,
> srini
>> + pinctrl_unregister(info->pctl);
>> +
>> + return 0;
>> +}
>> +
>> static struct platform_driver st_pctl_driver = {
>> .driver = {
>> .name = "st-pinctrl",
>> @@ -1692,6 +1716,7 @@ static struct platform_driver st_pctl_driver = {
>> .of_match_table = st_pctl_of_match,
>> },
>> .probe = st_pctl_probe,
>> + .remove = st_pctl_remove,
>> };
>>
>> static int __init st_pctl_init(void)
>>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
>
next prev parent reply other threads:[~2014-09-05 4:49 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-08-30 14:45 [PATCH] pinctrl: st: Add remove function and remove gpio_chip on failure Pramod Gurav
2014-09-04 16:53 ` Linus Walleij
2014-09-04 18:08 ` Srinivas Kandagatla
2014-09-05 4:48 ` Pramod Gurav [this message]
2014-09-05 7:27 ` Maxime Coquelin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=540940B0.5090000@smartplayin.com \
--to=pramod.gurav@smartplayin.com \
--cc=bjorn.andersson@sonymobile.com \
--cc=kernel@stlinux.com \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=maxime.coquelin@st.com \
--cc=patrice.chotard@st.com \
--cc=srinivas.kandagatla@gmail.com \
--cc=srinivas.kandagatla@linaro.com \
--cc=srinivas.kandagatla@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox