public inbox for linux-kernel@vger.kernel.org
 help / color / mirror / Atom feed
From: Camm Maguire <camm@enhanced.com>
To: Khalid Aziz <khalid@fc.hp.com>
Cc: linux-kernel@vger.kernel.org
Subject: Re: 2.2.18 IDE tape problem, with ide-scsi
Date: 27 Feb 2001 12:19:25 -0500	[thread overview]
Message-ID: <544rxg2gde.fsf@intech19.enhanced.com> (raw)
In-Reply-To: <54u25g3yb9.fsf_-_@intech19.enhanced.com> <3A9BC2A9.F5EE8554@fc.hp.com>
In-Reply-To: Khalid Aziz's message of "Tue, 27 Feb 2001 10:07:21 -0500"

Greetings, and thanks so much for your helpful reply!

Khalid Aziz <khalid@fc.hp.com> writes:

> Camm Maguire wrote:
> > 
> > The Conner gives the problem:
> > 
> > Feb 27 06:23:16 intech9 kernel: st0: Error with sense data: [valid=0] Info fld=0x0, Current st09:00: sns = 70  5
> > Feb 27 06:23:16 intech9 kernel: ASC=20 ASCQ= 0
> > Feb 27 06:23:16 intech9 kernel: Raw sense data:0x70 0x00 0x05 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x20 0x00 0x00 0x00
> > 
> > and occaisional 'gunzip: unexpected end of file' errors on verifying
> > the tape.
> > 
> > Take care,
> > 
> > --
> > Camm Maguire                                            camm@enhanced.com
> 
> ASC/ASCQ of 0x20/0x00 means "Invalid command operation code". So the
> drive is rejecting a command sent to it by the driver. If the other
> drive that is working is identical to seemingly non-working one, maybe
> this drive is going bad. 
> 

Thanks for the error identification.  The other drive is of a
*different* model.  This drive showed this behavior from the day I
bought it.  The drive could be going bad, but I doubt it.  Is it
possible that this manufacturer (Conner) has some peculiar
implementation of the spec?  I recall reading on this list sometime
back of similar workarounds to unusual drives.


> st driver prints the SCSI command that may have caused this error only
> when compiled with debug turned on. Maybe st driver should always print
> the command that results in a check condition as long as the command is
> not a Test Unit Ready or Mode Sense. 
>  

Can I turn on debug mode in runtime, or do I need to recompile
ide-scsi? 

Take care,


> ====================================================================
> Khalid Aziz                             Linux Development Laboratory
> (970)898-9214                                        Hewlett-Packard
> khalid@fc.hp.com                                    Fort Collins, CO
> 
> 

-- 
Camm Maguire			     			camm@enhanced.com
==========================================================================
"The earth is but one country, and mankind its citizens."  --  Baha'u'llah

  reply	other threads:[~2001-02-27 17:19 UTC|newest]

Thread overview: 25+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2001-02-27 16:06 2.2.18 IDE tape problem, with ide-scsi Camm Maguire
2001-02-27 15:07 ` Khalid Aziz
2001-02-27 17:19   ` Camm Maguire [this message]
2001-02-27 15:34     ` Khalid Aziz
2001-02-27 19:52       ` Camm Maguire
2001-02-27 18:18         ` Khalid Aziz
2001-02-27 20:26           ` Andre Hedrick
2001-02-27 21:26             ` Khalid Aziz
2001-02-28 15:23           ` Camm Maguire
2001-02-28 15:34             ` Mike Dresser
2001-03-07 22:54           ` Camm Maguire
2001-03-12 16:52             ` Khalid Aziz
2001-03-13 14:14               ` Camm Maguire
2001-02-27 17:32     ` Mike Dresser
2001-02-27 18:31       ` Camm Maguire
2001-02-27 18:34         ` Mike Dresser
2001-02-27 19:05           ` Andre Hedrick
2001-02-27 19:40             ` Camm Maguire
2001-03-01 17:02               ` Khalid Aziz
2001-02-27 22:21           ` Alan Cox
2001-02-27 19:01       ` Andre Hedrick
2001-02-27 19:04         ` Mike Dresser
2001-03-07  0:34 ` [PATCH] " Chip Salzenberg
2001-03-07  1:09   ` Andre Hedrick
     [not found] <Pine.LNX.4.10.10102271153560.29323-100000@coffee.psychology.mcmaster.ca>
2001-02-27 17:16 ` Camm Maguire

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=544rxg2gde.fsf@intech19.enhanced.com \
    --to=camm@enhanced.com \
    --cc=khalid@fc.hp.com \
    --cc=linux-kernel@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox