From: Camm Maguire <camm@enhanced.com>
To: linux-kernel@vger.kernel.org
Subject: 2.2.18 IDE tape problem, with ide-scsi
Date: 27 Feb 2001 11:06:34 -0500 [thread overview]
Message-ID: <54u25g3yb9.fsf_-_@intech19.enhanced.com> (raw)
In-Reply-To: jerry's message of "Mon, 26 Feb 2001 15:06:13 -0500"
Greetings! Two ide tapes, both on second ide channel, both using
ide-scsi. One works perfectly, the other basically works, but gives
errors, and occasionally doesn't write full 32k blocks to tape,
causing amanda errors.
Feb 25 06:14:22 intech9 kernel: ALI15X3: IDE controller on PCI bus 00 dev 78
Feb 25 06:14:22 intech9 kernel: ALI15X3: not 100%% native mode: will probe irqs later
Feb 25 06:14:22 intech9 kernel: ide0: BM-DMA at 0xb400-0xb407, BIOS settings: hda:DMA, hdb:DMA
Feb 25 06:14:22 intech9 kernel:
Feb 25 06:14:22 intech9 kernel: ************************************
Feb 25 06:14:22 intech9 kernel: * ALi IDE driver (1.0 beta3) *
Feb 25 06:14:22 intech9 kernel: * Chip Revision is C1 *
Feb 25 06:14:22 intech9 kernel: * Maximum capability is - UDMA 33 *
Feb 25 06:14:22 intech9 kernel: ************************************
Feb 25 06:14:22 intech9 kernel:
Feb 25 06:14:22 intech9 kernel: ide1: BM-DMA at 0xb408-0xb40f, BIOS settings: hdc:pio, hdd:pio
Feb 25 06:14:22 intech9 kernel: hda: FUJITSU MPE3064AT, ATA DISK drive
Feb 25 06:14:22 intech9 kernel: hdb: ST32140A, ATA DISK drive
Feb 25 06:14:22 intech9 kernel: hdc: CONNER CTT8000-A, ATAPI TAPE drive
Feb 25 06:14:22 intech9 kernel: hdd: HP COLORADO 14GB, ATAPI TAPE drive
Feb 25 06:14:22 intech9 kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Feb 25 06:14:22 intech9 kernel: ide1 at 0x170-0x177,0x376 on irq 15
Feb 25 06:14:22 intech9 kernel: ALI15X3: Ultra DMA enabled
Feb 25 06:14:22 intech9 kernel: hda: FUJITSU MPE3064AT, 6187MB w/512kB Cache, CHS=788/255/63, (U)DMA
Feb 25 06:14:22 intech9 kernel: ALI15X3: MultiWord DMA enabled
Feb 25 06:14:22 intech9 kernel: hdb: ST32140A, 2015MB w/128kB Cache, CHS=4095/16/63, DMA
Feb 25 06:14:22 intech9 kernel: hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 >
Feb 25 06:14:22 intech9 kernel: hdb: hdb1 hdb2
The Conner gives the problem:
Feb 27 06:23:16 intech9 kernel: st0: Error with sense data: [valid=0] Info fld=0x0, Current st09:00: sns = 70 5
Feb 27 06:23:16 intech9 kernel: ASC=20 ASCQ= 0
Feb 27 06:23:16 intech9 kernel: Raw sense data:0x70 0x00 0x05 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x20 0x00 0x00 0x00
and occaisional 'gunzip: unexpected end of file' errors on verifying
the tape.
Take care,
--
Camm Maguire camm@enhanced.com
==========================================================================
"The earth is but one country, and mankind its citizens." -- Baha'u'llah
next reply other threads:[~2001-02-27 16:08 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2001-02-27 16:06 Camm Maguire [this message]
2001-02-27 15:07 ` 2.2.18 IDE tape problem, with ide-scsi Khalid Aziz
2001-02-27 17:19 ` Camm Maguire
2001-02-27 15:34 ` Khalid Aziz
2001-02-27 19:52 ` Camm Maguire
2001-02-27 18:18 ` Khalid Aziz
2001-02-27 20:26 ` Andre Hedrick
2001-02-27 21:26 ` Khalid Aziz
2001-02-28 15:23 ` Camm Maguire
2001-02-28 15:34 ` Mike Dresser
2001-03-07 22:54 ` Camm Maguire
2001-03-12 16:52 ` Khalid Aziz
2001-03-13 14:14 ` Camm Maguire
2001-02-27 17:32 ` Mike Dresser
2001-02-27 18:31 ` Camm Maguire
2001-02-27 18:34 ` Mike Dresser
2001-02-27 19:05 ` Andre Hedrick
2001-02-27 19:40 ` Camm Maguire
2001-03-01 17:02 ` Khalid Aziz
2001-02-27 22:21 ` Alan Cox
2001-02-27 19:01 ` Andre Hedrick
2001-02-27 19:04 ` Mike Dresser
2001-03-07 0:34 ` [PATCH] " Chip Salzenberg
2001-03-07 1:09 ` Andre Hedrick
[not found] <Pine.LNX.4.10.10102271153560.29323-100000@coffee.psychology.mcmaster.ca>
2001-02-27 17:16 ` Camm Maguire
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=54u25g3yb9.fsf_-_@intech19.enhanced.com \
--to=camm@enhanced.com \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox