From: Nicolas Ferre <nicolas.ferre@atmel.com>
To: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>,
"Jean-Christophe Plagniol-Villard" <plagnioj@jcrosoft.com>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>
Subject: Re: [PATCH] ARM: at91: debug: use DEBUG_UART_PHYS
Date: Mon, 21 Sep 2015 16:22:19 +0200 [thread overview]
Message-ID: <5600129B.5040407@atmel.com> (raw)
In-Reply-To: <20150918221323.GK4287@piout.net>
Le 19/09/2015 00:13, Alexandre Belloni a écrit :
> Hi,
>
> On 18/09/2015 at 16:48:43 +0200, Nicolas Ferre wrote :
>>> - config AT91_DEBUG_LL_DBGU1
>>> - bool "Kernel low-level debugging on 9263, 9g45 and sama5d3"
>>> - select DEBUG_AT91_UART
>>> - depends on ARCH_AT91
>>> - depends on SOC_AT91SAM9 || SOC_SAMA5
>>> + SOC DEBUG_UART_PHYS DEBUG_UART_VIRT PORT
>>> + rm9200, 9260/9g20, 0xfffff200 0xfefff200 DBGU
>>> + 9261/9g10, 9rl
>>> + 9263, 9g45, sama5d3 0xffffee00 0xfeffee00 DBGU
>>> + sama5d4 0xfc00c000 0xfb00c000 USART3
>>> + sama5d4 0xfc069000 0xfb069000 DBGU
>>
>> This last one must be sama5d3, mustn't it?
>>
>
> No, that is the DBGU for sama5d4, sama5d3 is mentionned and is at
> 0xffffee00. I added it in case someone doesn't use USART3 for debugging
> and wants to use the DBGU. I actually doubt it may happen but we never
> now. I can remove it in a v2 if you prefer.
Ok, I understand now.
No need for a v2, I take this one in at91-4.4-soc branch.
Thanks, bye,
>
>> Otherwise I'm okay:
>> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
>>
>>> + sama5d2 0xf8020000 0xf7020000 UART1
>>>
>>> - config AT91_DEBUG_LL_DBGU2
>>> - bool "Kernel low-level debugging on sama5d4"
>>> - select DEBUG_AT91_UART
>>> - depends on ARCH_AT91
>>> - depends on SOC_SAMA5
>>> -
>>> - config AT91_DEBUG_LL_DBGU3
>>> - bool "Kernel low-level debugging on sama5d2"
>>> - select DEBUG_AT91_UART
>>> - depends on ARCH_AT91
>>> - depends on SOC_SAMA5
>>> + Please adjust DEBUG_UART_PHYS configuration options based on
>>> + your needs.
>>>
>>> config DEBUG_BCM2835
>>> bool "Kernel low-level debugging on BCM2835 PL011 UART"
>>> @@ -1242,10 +1236,6 @@ choice
>>>
>>> endchoice
>>>
>>> -config DEBUG_AT91_UART
>>> - bool
>>> - depends on ARCH_AT91
>>> -
>>> config DEBUG_EXYNOS_UART
>>> bool
>>>
>>> @@ -1476,7 +1466,8 @@ config DEBUG_UART_PHYS
>>> DEBUG_RMOBILE_SCIFA0 || DEBUG_RMOBILE_SCIFA1 || \
>>> DEBUG_RMOBILE_SCIFA4 || DEBUG_S3C24XX_UART || \
>>> DEBUG_UART_BCM63XX || DEBUG_ASM9260_UART || \
>>> - DEBUG_SIRFSOC_UART || DEBUG_DIGICOLOR_UA0
>>> + DEBUG_SIRFSOC_UART || DEBUG_DIGICOLOR_UA0 || \
>>> + DEBUG_AT91_UART
>>>
>>> config DEBUG_UART_VIRT
>>> hex "Virtual base address of debug UART"
>>> diff --git a/arch/arm/include/debug/at91.S b/arch/arm/include/debug/at91.S
>>> index 2556a8801c8c..43243be94cfc 100644
>>> --- a/arch/arm/include/debug/at91.S
>>> +++ b/arch/arm/include/debug/at91.S
>>> @@ -9,32 +9,22 @@
>>> *
>>> */
>>>
>>> -#if defined(CONFIG_AT91_DEBUG_LL_DBGU0)
>>> -#define AT91_DBGU 0xfffff200 /* AT91_BASE_DBGU0 */
>>> -#elif defined(CONFIG_AT91_DEBUG_LL_DBGU1)
>>> -#define AT91_DBGU 0xffffee00 /* AT91_BASE_DBGU1 */
>>> -#elif defined(CONFIG_AT91_DEBUG_LL_DBGU2)
>>> -/* On sama5d4, use USART3 as low level serial console */
>>> -#define AT91_DBGU 0xfc00c000 /* SAMA5D4_BASE_USART3 */
>>> -#else
>>> -/* On sama5d2, use UART1 as low level serial console */
>>> -#define AT91_DBGU 0xf8020000
>>> -#endif
>>> -
>>> #ifdef CONFIG_MMU
>>> #define AT91_IO_P2V(x) ((x) - 0x01000000)
>>> #else
>>> #define AT91_IO_P2V(x) (x)
>>> #endif
>>>
>>> +#define CONFIG_DEBUG_UART_VIRT AT91_IO_P2V(CONFIG_DEBUG_UART_PHYS)
>>> +
>>> #define AT91_DBGU_SR (0x14) /* Status Register */
>>> #define AT91_DBGU_THR (0x1c) /* Transmitter Holding Register */
>>> #define AT91_DBGU_TXRDY (1 << 1) /* Transmitter Ready */
>>> #define AT91_DBGU_TXEMPTY (1 << 9) /* Transmitter Empty */
>>>
>>> .macro addruart, rp, rv, tmp
>>> - ldr \rp, =AT91_DBGU @ System peripherals (phys address)
>>> - ldr \rv, =AT91_IO_P2V(AT91_DBGU) @ System peripherals (virt address)
>>> + ldr \rp, =CONFIG_DEBUG_UART_PHYS @ System peripherals (phys address)
>>> + ldr \rv, =CONFIG_DEBUG_UART_VIRT @ System peripherals (virt address)
>>> .endm
>>>
>>> .macro senduart,rd,rx
>>>
>>
>>
>> --
>> Nicolas Ferre
>
--
Nicolas Ferre
prev parent reply other threads:[~2015-09-21 14:23 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-08-08 10:11 [PATCH] ARM: at91: debug: use DEBUG_UART_PHYS Alexandre Belloni
2015-09-18 14:48 ` Nicolas Ferre
2015-09-18 22:13 ` Alexandre Belloni
2015-09-21 14:22 ` Nicolas Ferre [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=5600129B.5040407@atmel.com \
--to=nicolas.ferre@atmel.com \
--cc=alexandre.belloni@free-electrons.com \
--cc=boris.brezillon@free-electrons.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=plagnioj@jcrosoft.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox