Re: [RFC PATCH 1/2] drm: bridge: anx7688: Add anx7688 bridge driver support.

Nicolas Boichat
2016-06-22T02:45:43Z

Hi Archit,

Thanks for your reply.

On Tue, Jun 21, 2016 at 11:39 PM, Archit Taneja <architt@codeaurora.org> wrote:
> Hi,
>
> On 6/20/2016 12:44 PM, Nicolas Boichat wrote:
>>
>> ANX7688 is a HDMI to DP converter (as well as USB-C port controller),
>> that has an internal microcontroller.
>>
>> The only reason a Linux kernel driver is necessary is to reject
>> resolutions that require more bandwidth than what is available on
>> the DP side. DP bandwidth and lane count are reported by the bridge
>> via 2 registers on I2C.
>
>
> How does the chip know when to enable/disable itself? Does it shutoff
> itself if there isn't anything on the HDMI link?

Not 100% sure of the internals (there is a closed source firmware in
the chip), but I believe the HDMI/DP part of the chip is switched on
whenever there is a DP over USB-C connector plugged in.

>>
>> Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
>> ---
>>
>> Hi,
>>
>> I tested this driver using the Mediatek HDMI controller (MT8173) upstream
>> of the ANX bridge chip (Phillip sent a PULL request on June 13:
>> git://git.pengutronix.de/git/pza/linux.git tags/mediatek-drm-2016-06-13
>> ).
>>
>> I have 2 concerns, that I'm not sure how to address within the kernel DRM
>> framework:
>> 1. All other bridge drivers also have a connector attached to it.
>> However, in
>> this case, we cannot read the monitor EDID directly, so I'm not sure
>> what
>> I could put in a "get_modes" function. Instead, ANX7688 provides a
>> I2C
>> passthru/repeater, so the EDID is read on the Mediatek HDMI
>> controller side.
>>
>> That leads to a somewhat strange layout, where we have:
>> - MTK HDMI bridge/encoder
>> - MTK connector (HDMI)
>> - ANX7688 bridge
>> - No connector
>
>
>
> You should ideally have one DP connector at the end of the chain:
>
> - MTK HDMI bridge/encoder
> - ANX7688 bridge
> - Connector (DP)
>
> In the dt-bindings for this board, hdmi's output port shouldn't be
> connected to a hdmi connector, but the input port of the ANX7688
> DP bridge. The output port of the bridge should be the one that
> connects to the DP connector.

Yes that's what I do (in the device tree).

Actually, experimenting a bit more with the code, I realized that the
connector is always attached to the encoder, not the bridge, so the 2
layouts above are actually identical (from the userspace point of
view). Except that the connector name should be HDMI in one case, and
DP in the other. But I think that's mostly a cosmetic difference?

> One way I can think of fixing this is to make make the MTK hdmi
> encoder driver a bit smarter by observing the DT connections. If
> it's output port is connected to just a hdmi-connector, then
> things should be as before. If the output is connected to the DP
> bridge, then it should create a DP connector. The connector ops
> for the DP connector can still be the same as that of the HDMI
> connector before, but the phandle to the DDC bus would be in the
> DP device node in this case.

I think it'd be a bit weird to have the DDC bus phandle on the DP
connector, as we're not reading the EDID on the DP side of the bridge,
but on the HDMI side (and the bridge can do all sort of things to the
EDID: At the very least, I think it caches it).

> This way, you can get around having the correct layout.
>
> Ideally, a bridge driver shouldn't be the one that creates a
> connector. It may contain some of the connector functionality, but
> the connector creation should be managed by the kms driver.
> Almost all bridge drivers creating a connector in their .attach
> callbacks since they own some of the connector functionality (like
> reading EDID). That's something we're trying to fix by providing
> some more bridge api that kms drivers can use.
>
> Since this bridge driver doesn't have any connector functionality
> anyway, you should be okay.

Great, thanks for clarifying.

>>
>> Resolution filtering works fine though, thanks to mode_fixup callback
>> on the
>> bridge. It also helps that Mediatek HDMI bridge calls mode_fixup from
>> its
>> connector mode_valid callback, so that invalid modes are not even
>> presented
>> to userspace.
>>
>> 2. In the bandwidth computation, I hard-code 8-bit per channel (bpc).
>> bpc does
>> not seem to be included in the mode setting itself. We could possibly
>> iterate
>> over connectors on the DRM device, but then, IIUC,
>> connector->display_info.bpc
>> indicates the _maximum_ bpc supported by the monitor.
>
>
> I'm not clear about this either. Some drivers set a bus format
> on the connector via drm_display_info_set_bus_formats in their
> get_modes connector op, and then retrieve it later.

Ah, interesting... Seems like we'd need a big switch/case to convert
from bus_format to bpp, though.

>>
>> Any pointers? Thanks!
>>
>> Best,
>>
>> Nicolas
>>
>> drivers/gpu/drm/bridge/Kconfig | 9 ++
>> drivers/gpu/drm/bridge/Makefile | 1 +
>> drivers/gpu/drm/bridge/analogix-anx7688.c | 227
>> ++++++++++++++++++++++++++++++
>> 3 files changed, 237 insertions(+)
>> create mode 100644 drivers/gpu/drm/bridge/analogix-anx7688.c
>>
>> diff --git a/drivers/gpu/drm/bridge/Kconfig
>> b/drivers/gpu/drm/bridge/Kconfig
>> index 8f7423f..0c1eb41 100644
>> --- a/drivers/gpu/drm/bridge/Kconfig
>> +++ b/drivers/gpu/drm/bridge/Kconfig
>> @@ -7,6 +7,15 @@ config DRM_BRIDGE
>> menu "Display Interface Bridges"
>> depends on DRM && DRM_BRIDGE
>>
>> +config DRM_ANALOGIX_ANX7688
>> + tristate "Analogix ANX7688 bridge"
>> + depends on DRM
>> + select DRM_KMS_HELPER
>> + ---help---
>> + ANX7688 is a transmitter to support DisplayPort over USB-C for
>> + smartphone and tablets.
>> + This driver only supports the HDMI to DP component of the chip.
>> +
>> config DRM_ANALOGIX_ANX78XX
>> tristate "Analogix ANX78XX bridge"
>> select DRM_KMS_HELPER
>> diff --git a/drivers/gpu/drm/bridge/Makefile
>> b/drivers/gpu/drm/bridge/Makefile
>> index 96b13b3..d744c6c 100644
>> --- a/drivers/gpu/drm/bridge/Makefile
>> +++ b/drivers/gpu/drm/bridge/Makefile
>> @@ -1,5 +1,6 @@
>> ccflags-y := -Iinclude/drm
>>
>> +obj-$(CONFIG_DRM_ANALOGIX_ANX7688) += analogix-anx7688.o
>> obj-$(CONFIG_DRM_ANALOGIX_ANX78XX) += analogix-anx78xx.o
>> obj-$(CONFIG_DRM_DW_HDMI) += dw-hdmi.o
>> obj-$(CONFIG_DRM_DW_HDMI_AHB_AUDIO) += dw-hdmi-ahb-audio.o
>> diff --git a/drivers/gpu/drm/bridge/analogix-anx7688.c
>> b/drivers/gpu/drm/bridge/analogix-anx7688.c
>> new file mode 100644
>> index 0000000..2c34029
>> --- /dev/null
>> +++ b/drivers/gpu/drm/bridge/analogix-anx7688.c
>> @@ -0,0 +1,227 @@
>> +/*
>> + * ANX7688 HDMI->DP bridge driver
>> + *
>> + * Copyright (C) 2016 Google, Inc.
>> + *
>> + * This software is licensed under the terms of the GNU General Public
>> + * License version 2, as published by the Free Software Foundation, and
>> + * may be copied, distributed, and modified under those terms.
>> + *
>> + * This program is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + */
>> +
>> +#include <linux/delay.h>
>> +#include <linux/gpio.h>
>> +#include <linux/i2c.h>
>> +#include <linux/module.h>
>> +#include <linux/of.h>
>> +#include <linux/of_gpio.h>
>> +#include <drm/drmP.h>
>
>
> The 3 headers above aren't needed.

Nor gpio.h. Removed.

>
>> +#include <drm/drm_crtc.h>
>> +
>> +/* Register addresses */
>> +#define VENDOR_ID_REG 0x00
>> +#define DEVICE_ID_REG 0x02
>> +
>> +#define FW_VERSION_REG 0x80
>> +
>> +#define DP_BANDWIDTH_REG 0x85
>> +#define DP_LANE_COUNT_REG 0x86
>> +
>> +#define VENDOR_ID 0x1f29
>> +#define DEVICE_ID 0x7688
>> +
>> +/* First supported firmware version (0.85) */
>> +#define MINIMUM_FW_VERSION 0x0085
>> +
>> +struct anx7688 {
>> + struct drm_bridge bridge;
>> + struct i2c_client *client;
>> +
>> + bool filter;
>> +};
>> +
>> +static int anx7688_read(struct i2c_client *client, u8 reg, u8 *data,
>> + u16 data_len)
>> +{
>> + int ret;
>> + struct i2c_msg msgs[] = {
>> + {
>> + .addr = client->addr,
>> + .flags = 0,
>> + .len = 1,
>> + .buf = &reg,
>> + },
>> + {
>> + .addr = client->addr,
>> + .flags = I2C_M_RD,
>> + .len = data_len,
>> + .buf = data,
>> + }
>> + };
>> +
>> + ret = i2c_transfer(client->adapter, msgs, 2);
>> +
>> + if (ret == 2)
>> + return 0;
>> + if (ret < 0)
>> + return ret;
>> + else
>> + return -EIO;
>> +}
>> +
>> +static inline struct anx7688 *bridge_to_anx7688(struct drm_bridge
>> *bridge)
>> +{
>> + return container_of(bridge, struct anx7688, bridge);
>> +}
>> +
>> +static bool anx7688_bridge_mode_fixup(struct drm_bridge *bridge,
>> + const struct drm_display_mode *mode,
>> + struct drm_display_mode
>> *adjusted_mode)
>> +{
>> + struct anx7688 *anx7688 = bridge_to_anx7688(bridge);
>> + u8 regs[2];
>> + int totalbw, requiredbw;
>
>
> It might make sense to use a u32 or long or something here to prevent
> risk of overflow.

Well, mode->clock is already an int (and there won't be any overflow
in requiredbw unless we go for THz clocks ,-))

totalbw could do with a bit more of sanity checking (e.g. check that
regs[0] * regs[1] is not absurd). Like, we know regs[1] <= 2 on this
chip. Will fix.

>> + int ret;
>> +
>> + if (!anx7688->filter)
>> + return true;
>> +
>> + /* Read both regs 0x85 (bandwidth) and 0x86 (lane count). */
>> + ret = anx7688_read(anx7688->client, DP_BANDWIDTH_REG, regs, 2);
>
>
> Who programmed these registers in the first place? Is the lane count
> some sort of reset value? Or is it something that changes dynamically?

The ANX7688 OCM (on-chip microcontroller) sets it. It changes
depending on the downstream (DP) bandwidth/lane count, so it changes
on each plug event (after DP link training presumably).

>> + if (ret < 0) {
>> + dev_err(&anx7688->client->dev,
>> + "Failed to read bandwidth/lane count\n");
>> + return false;
>> + }
>> +
>> + /* Compute available rate (kHz) */
>> + totalbw = regs[0] * regs[1] * 270000 * 8 / 10;
>> +
>> + /* Required bandwidth (8 bpc) */
>> + requiredbw = mode->clock * 8 * 3;
>> +
>> + dev_dbg(&anx7688->client->dev,
>> + "DP bandwidth: %d kHz (%02x/%d); mode requires %d Khz\n",
>> + totalbw, regs[0], regs[1], requiredbw);
>> +
>> + if (totalbw == 0) {
>> + dev_warn(&anx7688->client->dev,
>> + "Bandwidth/lane count are 0, not rejecting
>> modes\n");
>> + return true;
>> + }
>> +
>> + return totalbw >= requiredbw;
>> +}
>> +
>> +static const struct drm_bridge_funcs anx7688_bridge_funcs = {
>> + .mode_fixup = anx7688_bridge_mode_fixup,
>> +};
>> +
>> +static int anx7688_i2c_probe(struct i2c_client *client,
>> + const struct i2c_device_id *id)
>> +{
>> + struct anx7688 *anx7688;
>> + int ret;
>> + u8 buffer[4];
>> + u16 vendor, device, fwversion;
>> +
>> + anx7688 = devm_kzalloc(&client->dev, sizeof(*anx7688),
>> GFP_KERNEL);
>> + if (!anx7688)
>> + return -ENOMEM;
>> +
>> +#if IS_ENABLED(CONFIG_OF)
>> + anx7688->bridge.of_node = client->dev.of_node;
>> +#endif
>> +
>> + anx7688->client = client;
>> + i2c_set_clientdata(client, anx7688);
>> +
>> + /* Read both vendor and device id (4 bytes). */
>> + ret = anx7688_read(client, VENDOR_ID_REG, buffer, 4);
>> + if (ret) {
>> + dev_err(&client->dev, "Failed to read chip vendor/device
>> id\n");
>> + return ret;
>> + }
>> +
>> + vendor = (u16)buffer[1] << 8 | buffer[0];
>> + device = (u16)buffer[3] << 8 | buffer[2];
>> + if (vendor != VENDOR_ID || device != DEVICE_ID) {
>> + dev_err(&client->dev,
>> + "Invalid vendor/device id %04x/%04x\n",
>> + vendor, device);
>> + return -ENODEV;
>> + }
>> +
>> + ret = anx7688_read(client, FW_VERSION_REG, buffer, 2);
>> + if (ret) {
>> + dev_err(&client->dev, "Failed to read firmware
>> version\n");
>> + return ret;
>> + }
>> +
>> + fwversion = (u16)buffer[0] << 8 | buffer[1];
>> + dev_info(&client->dev, "ANX7688 firwmare version %02x.%02x\n",
>> + buffer[0], buffer[1]);
>> +
>> + /* FW version >= 0.85 supports bandwidth/lane count registers */
>> + if (fwversion >= MINIMUM_FW_VERSION) {
>> + anx7688->filter = true;
>> + } else {
>> + /* Warn, but not fail, for backwards compatiblity. */
>
>
> s/compatiblity/compatibility

Will fix.

>
>> + dev_warn(&client->dev,
>> + "Old ANX7688 FW version (%04x), not filtering\n",
>> + fwversion);
>> + }
>> +
>> + anx7688->bridge.funcs = &anx7688_bridge_funcs;
>> + ret = drm_bridge_add(&anx7688->bridge);
>> + if (ret < 0) {
>> + dev_err(&client->dev, "Failed to add drm bridge\n");
>> + return ret;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int anx7688_i2c_remove(struct i2c_client *client)
>> +{
>> + struct anx7688 *anx7688 = i2c_get_clientdata(client);
>> +
>> + drm_bridge_remove(&anx7688->bridge);
>> +
>> + return 0;
>> +}
>> +
>> +static const struct i2c_device_id anx7688_id[] = {
>> + { "anx7688", 0 },
>> + { /* sentinel */ }
>> +};
>> +
>> +MODULE_DEVICE_TABLE(i2c, anx7688_id);
>> +
>> +#if IS_ENABLED(CONFIG_OF)
>> +static const struct of_device_id anx7688_match_table[] = {
>> + { .compatible = "analogix,anx7688", },
>> + { /* sentinel */ },
>> +};
>> +MODULE_DEVICE_TABLE(of, anx7688_match_table);
>> +#endif
>> +
>> +static struct i2c_driver anx7688_driver = {
>> + .driver = {
>> + .name = "anx7688",
>> + .of_match_table = of_match_ptr(anx7688_match_table),
>> + },
>> + .probe = anx7688_i2c_probe,
>> + .remove = anx7688_i2c_remove,
>> + .id_table = anx7688_id,
>> +};
>> +
>> +module_i2c_driver(anx7688_driver);
>> +
>> +MODULE_DESCRIPTION("ANX7688 SlimPort Transmitter driver");
>> +MODULE_AUTHOR("Nicolas Boichat <drinkcat@chromium.org>");
>> +MODULE_LICENSE("GPL v2");
>>
>
> --
> Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
> a Linux Foundation Collaborative Project