Re: [RESEND v14 PATCH 1/5] Documentation: bindings: add dt doc for Rockchip USB Type-C PHY

[Kishon Vijay Abraham I <kishon@ti.com>]

On Tuesday 06 September 2016 10:30 PM, Chris Zhong wrote:
> This patch adds a binding that describes the Rockchip USB Type-C PHY
> for rk3399
> 
> Signed-off-by: Chris Zhong <zyw@rock-chips.com>
> Reviewed-by: Tomasz Figa <tfiga@chromium.org>
> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
> Reviewed-by: Guenter Roeck <linux@roeck-us.net>
> Acked-by: Rob Herring <robh@kernel.org>

merged, thanks.

-Kishon
> 
> ---
> 
> Changes in v14: None
> Changes in v13: None
> Changes in v12: None
> Changes in v11:
> - make a clearer emarcation between usb phy and dp phy
> 
> Changes in v10:
> - remove rockchip,uphy-dp-sel property
> 
> Changes in v9:
> - change #phy-cells to 1
> 
> Changes in v8: None
> Changes in v7: None
> Changes in v6:
> - add assigned-clocks and assigned-clock-rates
> 
> Changes in v5: None
> Changes in v4:
> - add a #phy-cells node
> 
> Changes in v3:
> - use compatible: rockchip,rk3399-typec-phy
> - use dashes instead of underscores.
> 
> Changes in v2:
> - add some registers description
> 
> Changes in v1:
> - add extcon node description
> - move the registers in phy driver
> - remove the suffix of reset
> 
>  .../devicetree/bindings/phy/phy-rockchip-typec.txt | 101 +++++++++++++++++++++
>  1 file changed, 101 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt
> 
> diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt b/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt
> new file mode 100644
> index 0000000..6ea867e
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt
> @@ -0,0 +1,101 @@
> +* ROCKCHIP type-c PHY
> +---------------------
> +
> +Required properties:
> + - compatible : must be "rockchip,rk3399-typec-phy"
> + - reg: Address and length of the usb phy control register set
> + - rockchip,grf : phandle to the syscon managing the "general
> +   register files"
> + - clocks : phandle + clock specifier for the phy clocks
> + - clock-names : string, clock name, must be "tcpdcore", "tcpdphy-ref";
> + - assigned-clocks: main clock, should be <&cru SCLK_UPHY0_TCPDCORE> or
> +		    <&cru SCLK_UPHY1_TCPDCORE>;
> + - assigned-clock-rates : the phy core clk frequency, shall be: 50000000
> + - resets : a list of phandle + reset specifier pairs
> + - reset-names : string reset name, must be:
> +		 "uphy", "uphy-pipe", "uphy-tcphy"
> + - extcon : extcon specifier for the Power Delivery
> +
> +Note, there are 2 type-c phys for RK3399, and they are almost identical, except
> +these registers(description below), every register node contains 3 sections:
> +offset, enable bit, write mask bit.
> + - rockchip,typec-conn-dir : the register of type-c connector direction,
> +   for type-c phy0, it must be <0xe580 0 16>;
> +   for type-c phy1, it must be <0xe58c 0 16>;
> + - rockchip,usb3tousb2-en : the register of type-c force usb3 to usb2 enable
> +   control.
> +   for type-c phy0, it must be <0xe580 3 19>;
> +   for type-c phy1, it must be <0xe58c 3 19>;
> + - rockchip,external-psm : the register of type-c phy external psm clock
> +   selection.
> +   for type-c phy0, it must be <0xe588 14 30>;
> +   for type-c phy1, it must be <0xe594 14 30>;
> + - rockchip,pipe-status : the register of type-c phy pipe status.
> +   for type-c phy0, it must be <0xe5c0 0 0>;
> +   for type-c phy1, it must be <0xe5c0 16 16>;
> +
> +Required nodes : a sub-node is required for each port the phy provides.
> +		 The sub-node name is used to identify dp or usb3 port,
> +		 and shall be the following entries:
> +	* "dp-port" : the name of DP port.
> +	* "usb3-port" : the name of USB3 port.
> +
> +Required properties (port (child) node):
> +- #phy-cells : must be 0, See ./phy-bindings.txt for details.
> +
> +Example:
> +	tcphy0: phy@ff7c0000 {
> +		compatible = "rockchip,rk3399-typec-phy";
> +		reg = <0x0 0xff7c0000 0x0 0x40000>;
> +		rockchip,grf = <&grf>;
> +		extcon = <&fusb0>;
> +		clocks = <&cru SCLK_UPHY0_TCPDCORE>,
> +			 <&cru SCLK_UPHY0_TCPDPHY_REF>;
> +		clock-names = "tcpdcore", "tcpdphy-ref";
> +		assigned-clocks = <&cru SCLK_UPHY0_TCPDCORE>;
> +		assigned-clock-rates = <50000000>;
> +		resets = <&cru SRST_UPHY0>,
> +			 <&cru SRST_UPHY0_PIPE_L00>,
> +			 <&cru SRST_P_UPHY0_TCPHY>;
> +		reset-names = "uphy", "uphy-pipe", "uphy-tcphy";
> +		rockchip,typec-conn-dir = <0xe580 0 16>;
> +		rockchip,usb3tousb2-en = <0xe580 3 19>;
> +		rockchip,external-psm = <0xe588 14 30>;
> +		rockchip,pipe-status = <0xe5c0 0 0>;
> +
> +		tcphy0_dp: dp-port {
> +			#phy-cells = <0>;
> +		};
> +
> +		tcphy0_usb3: usb3-port {
> +			#phy-cells = <0>;
> +		};
> +	};
> +
> +	tcphy1: phy@ff800000 {
> +		compatible = "rockchip,rk3399-typec-phy";
> +		reg = <0x0 0xff800000 0x0 0x40000>;
> +		rockchip,grf = <&grf>;
> +		extcon = <&fusb1>;
> +		clocks = <&cru SCLK_UPHY1_TCPDCORE>,
> +			 <&cru SCLK_UPHY1_TCPDPHY_REF>;
> +		clock-names = "tcpdcore", "tcpdphy-ref";
> +		assigned-clocks = <&cru SCLK_UPHY1_TCPDCORE>;
> +		assigned-clock-rates = <50000000>;
> +		resets = <&cru SRST_UPHY1>,
> +			 <&cru SRST_UPHY1_PIPE_L00>,
> +			 <&cru SRST_P_UPHY1_TCPHY>;
> +		reset-names = "uphy", "uphy-pipe", "uphy-tcphy";
> +		rockchip,typec-conn-dir = <0xe58c 0 16>;
> +		rockchip,usb3tousb2-en = <0xe58c 3 19>;
> +		rockchip,external-psm = <0xe594 14 30>;
> +		rockchip,pipe-status = <0xe5c0 16 16>;
> +
> +		tcphy1_dp: dp-port {
> +			#phy-cells = <0>;
> +		};
> +
> +		tcphy1_usb3: usb3-port {
> +			#phy-cells = <0>;
> +		};
> +	};
>