From: Jiada Wang <jiada_wang@mentor.com>
To: Rob Herring <robh@kernel.org>
Cc: Mark Brown <broonie@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Shawn Guo <shawnguo@kernel.org>,
"kernel@pengutronix.de" <kernel@pengutronix.de>,
Fabio Estevam <fabio.estevam@nxp.com>,
"linux-spi@vger.kernel.org" <linux-spi@vger.kernel.org>,
"devicetree@vger.kernel.org" <devicetree@vger.kernel.org>,
"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>,
"linux-arm-kernel@lists.infradead.org"
<linux-arm-kernel@lists.infradead.org>
Subject: Re: [PATCH linux-next v4 2/4] spi: imx: add selection for iMX53 and iMX6 controller
Date: Mon, 26 Jun 2017 18:25:52 -0700 [thread overview]
Message-ID: <5951B420.9080400@mentor.com> (raw)
In-Reply-To: <CAL_JsqJeh=M0qB2m6DPLo1_WJsUKowvS0FpUgsmEuF5KuKPTRw@mail.gmail.com>
Hello Mark and Sascha
Could you please review my v4 patch set for i.MX SPI slave support
Thanks,
Jiada
On 06/13/2017 07:29 AM, Rob Herring wrote:
> On Tue, Jun 13, 2017 at 12:28 AM, Jiada Wang<jiada_wang@mentor.com> wrote:
>> Hello Rob
>>
>>
>> On 06/13/2017 12:53 AM, Rob Herring wrote:
>>> On Thu, Jun 08, 2017 at 02:16:01PM +0900, Jiada Wang wrote:
>>>> ECSPI contorller for iMX53 and iMX6 has few hardware issues
>>>> comparing to iMX51.
>>>> The change add possibility to detect which controller is used
>>>> to apply possible workaround and limitations.
>>>>
>>>> Signed-off-by: Jiada Wang<jiada_wang@mentor.com>
>>>> ---
>>>> .../devicetree/bindings/spi/fsl-imx-cspi.txt | 1 +
>>>> drivers/spi/spi-imx.c | 26
>>>> ++++++++++++++++++++--
>>>> 2 files changed, 25 insertions(+), 2 deletions(-)
>>>>
>>>> diff --git a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt
>>>> b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt
>>>> index 31b5b21..5bf1396 100644
>>>> --- a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt
>>>> +++ b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt
>>>> @@ -9,6 +9,7 @@ Required properties:
>>>> - "fsl,imx31-cspi" for SPI compatible with the one integrated on
>>>> i.MX31
>>>> - "fsl,imx35-cspi" for SPI compatible with the one integrated on
>>>> i.MX35
>>>> - "fsl,imx51-ecspi" for SPI compatible with the one integrated on
>>>> i.MX51
>>>> + - "fsl,imx53-ecspi" for SPI compatible with the one integrated on
>>>> i.MX53 and later Soc
>>>> - reg : Offset and length of the register set for the device
>>>> - interrupts : Should contain CSPI/eCSPI interrupt
>>>> - cs-gpios : Specifies the gpio pins to be used for chipselects.
>>>> diff --git a/drivers/spi/spi-imx.c b/drivers/spi/spi-imx.c
>>>> index 4469121..8e6f339 100644
>>>> --- a/drivers/spi/spi-imx.c
>>>> +++ b/drivers/spi/spi-imx.c
>>>> @@ -63,7 +63,8 @@ enum spi_imx_devtype {
>>>> IMX27_CSPI,
>>>> IMX31_CSPI,
>>>> IMX35_CSPI, /* CSPI on all i.mx except above */
>>>> - IMX51_ECSPI, /* ECSPI on i.mx51 and later */
>>>> + IMX51_ECSPI, /* ECSPI on i.mx51 */
>>>> + IMX53_ECSPI, /* ECSPI on i.mx53 and later */
>>>
>>> Looks like i.MX51 and i.MX53 are the same. While the DT should have
>>> different compatibles (with fallbacks), the driver should map them to
>>> the same type until there's some difference found.
>>>
>> the difference between i.MX51 and i.MX53 is introduced in the
>> 4th patch "spi: imx: Add support for SPI Slave mode" in this patch set
> Okay, I missed that.
>
>> do you think, I need to merge the two patches into one?
> No, not necessary.
>
> Acked-by: Rob Herring<robh@kernel.org>
>
> Rob
next prev parent reply other threads:[~2017-06-27 1:26 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-06-08 5:15 [PATCH linux-next v4 0/4] i.MX ECSPI controller slave mode support Jiada Wang
2017-06-08 5:16 ` [PATCH linux-next v4 1/4] spi: imx: introduce fifo_size and has_dmamode in spi_imx_devtype_data Jiada Wang
2017-07-11 14:43 ` Applied "spi: imx: introduce fifo_size and has_dmamode in spi_imx_devtype_data" to the spi tree Mark Brown
2017-06-08 5:16 ` [PATCH linux-next v4 2/4] spi: imx: add selection for iMX53 and iMX6 controller Jiada Wang
2017-06-12 15:53 ` Rob Herring
2017-06-13 5:28 ` Jiada Wang
2017-06-13 14:29 ` Rob Herring
2017-06-27 1:25 ` Jiada Wang [this message]
2017-06-28 19:17 ` Mark Brown
2017-06-08 5:16 ` [PATCH linux-next v4 3/4] ARM: dts: imx: change compatibility for SPI controllers on imx53 later soc Jiada Wang
2017-06-08 5:16 ` [PATCH linux-next v4 4/4] spi: imx: Add support for SPI Slave mode Jiada Wang
2017-07-11 14:42 ` Mark Brown
2017-06-27 6:53 ` [PATCH linux-next v4 0/4] i.MX ECSPI controller slave mode support Sascha Hauer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=5951B420.9080400@mentor.com \
--to=jiada_wang@mentor.com \
--cc=broonie@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=fabio.estevam@nxp.com \
--cc=kernel@pengutronix.de \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-spi@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh@kernel.org \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox