ITERaid and atkbd

ITERaid and atkbd

[Mile Davidovic]

Hi folks

I have trouble with IT8212F raid controller (on Gigabyte boards also known
as GigaRaid) on FedoraCore 3.
There was some problem with building modules but after some fixing Makefile
I succeeded to build module. 

After loading module dmesg shows:
	Found Controller: IT8212 UDMA/ATA133 RAID Controller
	FindDevices: device 0 is IDE
	FindDevices: device 1 is IDE
	Channel[0] BM-DMA at 0xA400-0xA407
	Channel[1] BM-DMA at 0xA408-0xA40F
	scsi2 : ITE RAIDExpress133
	  Vendor: ITE       Model: IT8212F           Rev: 1.3
	  Type:   Direct-Access                      ANSI SCSI revision: 00
	SCSI device sdb: 488397166 512-byte hdwr sectors (250059 MB)
	sdb: asking for cache data failed
	sdb: assuming drive cache: write through
	 sdb: sdb1
	Attached scsi disk sdb at scsi2, channel 0, id 0, lun 0
	  Vendor: ITE       Model: IT8212F           Rev: 1.3
	  Type:   Direct-Access                      ANSI SCSI revision: 00
	SCSI device sdc: 488397166 512-byte hdwr sectors (250059 MB)
	sdc: asking for cache data failed
	sdc: assuming drive cache: write through
	 sdc:<4>atkbd.c: Unknown key pressed (translated set 2, code 0x0 on
isa0060/serio0).
	atkbd.c: Use 'setkeycodes 00 <keycode>' to make it known.
	atkbd.c: Unknown key pressed (translated set 2, code 0x0 on
isa0060/serio0).
	atkbd.c: Use 'setkeycodes 00 <keycode>' to make it known.
	 sdc1
	Attached scsi disk sdc at scsi2, channel 0, id 1, lun 0

[root@beowulf scsi]# mount /dev/sdb1 /mnt/
atkbd.c: Unknown key pressed (translated set 2, code 0x0 on isa0060/serio0).
atkbd.c: Use 'setkeycodes 00 <keycode>' to make it known.
...
atkbd.c: Unknown key pressed (translated set 2, code 0x0 on isa0060/serio0).
atkbd.c: Use 'setkeycodes 00 <keycode>' to make it known.
kjournald starting.  Commit interval 5 seconds
atkbd.c: Unknown key pressed (translated set 2, code 0x0 on isa0060/serio0).
atkbd.c: Use 'setkeycodes 00 <keycode>' to make it known.
EXT3 FS on sdb1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
atkbd.c: Unknown key pressed (translated set 2, code 0x0 on isa0060/serio0).
atkbd.c: Use 'setkeycodes 00 <keycode>' to make it known.

I found a lot of messages with this subject but I didn't found any final
answer.
I also tried to use iteraid driver from mm tree but situation is same.

Thanks in a advice
Best regards Mile

Re: ITERaid and atkbd

[Rahul Karnik]

On Tue, 16 Nov 2004 15:23:30 +0100, Mile Davidovic
<mile.davidovic@micronasnit.com> wrote:
> Hi folks
> 
> I have trouble with IT8212F raid controller (on Gigabyte boards also known
> as GigaRaid) on FedoraCore 3.

Try the ac kernels. 

Arjan has some RPMs for FC3.

http://marc.theaimsgroup.com/?l=linux-kernel&m=110060681900689&w=2

-Rahul

RE: ITERaid and atkbd

[Mile Davidovic]

Thanks a lot.

When I rebuild iteraid driver it works without complaining. Now testing
begin.

Best regards Mile

-----Original Message-----
From: linux-kernel-owner@vger.kernel.org
[mailto:linux-kernel-owner@vger.kernel.org] On Behalf Of Rahul Karnik
Sent: Tuesday, November 16, 2004 4:17 PM
To: mile.davidovic@micronasnit.com
Cc: linux-kernel@vger.kernel.org
Subject: Re: ITERaid and atkbd

On Tue, 16 Nov 2004 15:23:30 +0100, Mile Davidovic
<mile.davidovic@micronasnit.com> wrote:
> Hi folks
> 
> I have trouble with IT8212F raid controller (on Gigabyte boards also 
> known as GigaRaid) on FedoraCore 3.

Try the ac kernels. 

Arjan has some RPMs for FC3.

http://marc.theaimsgroup.com/?l=linux-kernel&m=110060681900689&w=2

-Rahul
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org More majordomo info at
http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/