public inbox for linux-kernel@vger.kernel.org
 help / color / mirror / Atom feed
From: Archit Taneja <architt@codeaurora.org>
To: John Stultz <john.stultz@linaro.org>,
	lkml <linux-kernel@vger.kernel.org>
Cc: David Airlie <airlied@linux.ie>,
	Wolfram Sang <wsa+renesas@sang-engineering.com>,
	Lars-Peter Clausen <lars@metafoo.de>,
	Laurent Pinchart <laurent.pinchart@ideasonboard.com>,
	dri-devel@lists.freedesktop.org
Subject: Re: [PATCH 0/5 v3] adv7511 EDID probing improvements
Date: Wed, 11 Jan 2017 14:18:32 +0530	[thread overview]
Message-ID: <5dffb907-9989-a555-0208-b662beccfaef@codeaurora.org> (raw)
In-Reply-To: <1483472502-16403-1-git-send-email-john.stultz@linaro.org>

Hi,

On 01/04/2017 01:11 AM, John Stultz wrote:
> Hope everyone had a good newyears!
>
> Wanted to re-send out v3 of this patch set improving the EDID
> probing on the adv7511 used on HiKey, for consideration for
> merging for 4.11
>
> The first three patches are fixups that are hopefully straight
> forward, integrating feedback I got from Laurant.
>
> The last two patches try to clean up and resue code, which as
> a side effect avoids an issue I'm seeing where something is
> going wrong with the regmap cache state for the
> ADV7511_REG_EDID_I2C_ADDR(0x43) register which results in
> i2c_transfer errors if we don't do the
> regcache_sync/_mark_dirty() calls. I suspect there might be a
> better solution there, but have not gotten any other suggestions
> so I wanted to go ahead and submit these.
>
> Thoughts and feedback would be appreciated!

Tested on DB410c on 4.10-rc3. Works well for me.

Thanks,
Archit

>
> thanks
> -john
>
> New in v3:
> * Addressed naming improvements and drm_kms_helper_hotplug_event
>   usage corrections as suggested by Laurent.
>
> Cc: David Airlie <airlied@linux.ie>
> Cc: Archit Taneja <architt@codeaurora.org>
> Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
> Cc: Lars-Peter Clausen <lars@metafoo.de>
> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Cc: dri-devel@lists.freedesktop.org
>
> Archit Taneja (1):
>   drm/bridge: adv7511: Enable HPD interrupts to support hotplug and
>     improve monitor detection
>
> John Stultz (4):
>   drm/bridge: adv7511: Use work_struct to defer hotplug handing to out
>     of irq context
>   drm/bridge: adv7511: Switch to using drm_kms_helper_hotplug_event()
>   drm/bridge: adv7511: Rework adv7511_power_on/off() so they can be
>     reused internally
>   drm/bridge: adv7511: Reuse __adv7511_power_on/off() when probing EDID
>
>  drivers/gpu/drm/bridge/adv7511/adv7511.h     |  2 +
>  drivers/gpu/drm/bridge/adv7511/adv7511_drv.c | 62 +++++++++++++++++++---------
>  2 files changed, 44 insertions(+), 20 deletions(-)
>

-- 
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project

  parent reply	other threads:[~2017-01-11  8:48 UTC|newest]

Thread overview: 20+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2017-01-03 19:41 [PATCH 0/5 v3] adv7511 EDID probing improvements John Stultz
2017-01-03 19:41 ` [PATCH 1/5 v3] drm/bridge: adv7511: Use work_struct to defer hotplug handing to out of irq context John Stultz
2017-01-03 19:41 ` [PATCH 2/5 v3] drm/bridge: adv7511: Switch to using drm_kms_helper_hotplug_event() John Stultz
2017-01-16 15:47   ` Laurent Pinchart
2017-01-16 15:56     ` Laurent Pinchart
2017-01-16 19:31       ` John Stultz
2017-01-03 19:41 ` [PATCH 3/5 v3] drm/bridge: adv7511: Enable HPD interrupts to support hotplug and improve monitor detection John Stultz
2017-01-03 19:41 ` [PATCH 4/5 v3] drm/bridge: adv7511: Rework adv7511_power_on/off() so they can be reused internally John Stultz
2017-01-16 15:50   ` Laurent Pinchart
2017-01-03 19:41 ` [PATCH 5/5 v3] drm/bridge: adv7511: Reuse __adv7511_power_on/off() when probing EDID John Stultz
2017-01-16 16:03   ` Laurent Pinchart
2017-01-16 20:14     ` John Stultz
2017-01-16 22:25       ` Laurent Pinchart
2017-01-16 23:16         ` [RFC][PATCH] drm/bridge: adv7511: Re-write the i2c address as it may have been lost John Stultz
2017-01-16 23:36           ` Laurent Pinchart
2017-01-16 23:39             ` John Stultz
2017-01-11  8:48 ` Archit Taneja [this message]
2017-01-12  0:06   ` [PATCH 0/5 v3] adv7511 EDID probing improvements John Stultz
2017-01-12  4:22     ` Archit Taneja
2017-01-16 15:57 ` Laurent Pinchart

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=5dffb907-9989-a555-0208-b662beccfaef@codeaurora.org \
    --to=architt@codeaurora.org \
    --cc=airlied@linux.ie \
    --cc=dri-devel@lists.freedesktop.org \
    --cc=john.stultz@linaro.org \
    --cc=lars@metafoo.de \
    --cc=laurent.pinchart@ideasonboard.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=wsa+renesas@sang-engineering.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox