Re: [PATCH 1/5] dt-bindings: phy: Add STM32MP25 COMBOPHY bindings

[Krzysztof Kozlowski <krzk@kernel.org>]

On 27/08/2024 14:24, Christian Bruel wrote:
> Document the bindings for STM32 COMBOPHY interface, used to support
> the PCIe and USB3 stm32mp25 drivers.
> Following entries can be used to tune caracterisation parameters
>  - st,output-micro-ohms and st,output-vswing-microvolt bindings entries
> to tune the impedance and voltage swing using discrete simulation results
>  - st,rx-equalizer register to set the internal rx equalizer filter value.
> 
> Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
> Signed-off-by: Christian Bruel <christian.bruel@foss.st.com>

v1? Or v3?

> ---
>  .../bindings/phy/st,stm32-combophy.yaml       | 144 ++++++++++++++++++
>  1 file changed, 144 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/phy/st,stm32-combophy.yaml
> 
> diff --git a/Documentation/devicetree/bindings/phy/st,stm32-combophy.yaml b/Documentation/devicetree/bindings/phy/st,stm32-combophy.yaml
> new file mode 100644
> index 000000000000..c33a843b83a3
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/st,stm32-combophy.yaml

Filename matching compatible.

> @@ -0,0 +1,144 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/phy/st,stm32-combophy.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: STMicroelectronics STM32MP25 USB3/PCIe COMBOPHY
> +
> +maintainers:
> +  - Christian Bruel <christian.bruel@foss.st.com>
> +
> +description:
> +  Single lane PHY shared (exclusive) between the USB3 and PCIe controllers.
> +  Supports 5Gbit/s for USB3 and PCIe gen2 or 2.5Gbit/s for PCIe gen1.
> +
> +properties:
> +  compatible:
> +    const: st,stm32mp25-combophy
> +
> +  reg:
> +    maxItems: 1
> +
> +  "#phy-cells":
> +    const: 1
> +    description: |
> +      The cells contain the following arguments.
> +
> +      - description: The PHY type

That's some sort of mess. Is it schema within description or schema? Why
two descriptions?

> +          enum:
> +            - PHY_TYPE_USB3
> +            - PHY_TYPE_PCIE
> +

...

> +required:
> +  - compatible
> +  - reg
> +  - st,syscfg
> +  - '#phy-cells'
> +  - resets
> +  - reset-names
> +  - clocks
> +  - clock-names
> +
> +allOf:
> +  - if:
> +      required:
> +        - wakeup-source
> +    then:
> +      anyOf:
> +        - required: [interrupts]
> +        - required: [interrupts-extended]
> +

I do not see any improvements.

The tag you received was CONDITIONAL. If you do not apply the comments,
you cannot just apply the tag.

Best regards,
Krzysztof