Re: [PATCH 2/2] dts: hisilicon: add support for USB3 on Hikey 970

[Wei Xu <xuwei5@hisilicon.com>]

Hi Mauro,

On 2021/7/24 16:55, Mauro Carvalho Chehab wrote:
> Add the USB3 bindings for Kirin 970 phy and Hikey 970 board.
> 
> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

Fine to me and I can merge this patch once the binding for the 
"kirin970_hikey_usbhub" and "hi3670-dwc3" are ready.
Thanks!

Best Regards,
Wei

> ---
>  .../boot/dts/hisilicon/hi3670-hikey970.dts    | 107 ++++++++++++++++++
>  arch/arm64/boot/dts/hisilicon/hi3670.dtsi     |  56 +++++++++
>  2 files changed, 163 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts b/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts
> index 7c32f5fd5cc5..16f81f86e3fa 100644
> --- a/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts
> +++ b/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts
> @@ -53,6 +53,30 @@ wlan_en: wlan-en-1-8v {
>  		startup-delay-us = <70000>;
>  		enable-active-high;
>  	};
> +
> +	hikey_usbhub: hikey_usbhub {
> +		compatible = "hisilicon,kirin970_hikey_usbhub";
> +
> +		typec-vbus-gpios = <&gpio26 1 0>;
> +		otg-switch-gpios = <&gpio4 2 0>;
> +		hub_reset_en_gpio = <&gpio0 3 0>;
> +		hub-vdd-supply = <&ldo17>;
> +		usb-role-switch;
> +
> +		port {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			hikey_usb_ep0: endpoint@0 {
> +				reg = <0>;
> +				remote-endpoint = <&dwc3_role_switch>;
> +			};
> +			hikey_usb_ep1: endpoint@1 {
> +				reg = <1>;
> +				remote-endpoint = <&rt1711h_ep>;
> +			};
> +		};
> +	};
>  };
>  
>  /*
> @@ -430,3 +454,86 @@ &uart6 {
>  	label = "LS-UART1";
>  	status = "okay";
>  };
> +
> +&usb_phy {
> +	phy-supply = <&ldo17>;
> +};
> +
> +&i2c1 {
> +	status = "okay";
> +
> +	rt1711h: rt1711h@4e {
> +		compatible = "richtek,rt1711h";
> +		reg = <0x4e>;
> +		status = "okay";
> +		interrupt-parent = <&gpio27>;
> +		interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&usb_cfg_func>;
> +
> +		usb_con: connector {
> +			compatible = "usb-c-connector";
> +			label = "USB-C";
> +			data-role = "dual";
> +			power-role = "dual";
> +			try-power-role = "sink";
> +			source-pdos = <PDO_FIXED(5000, 500, PDO_FIXED_USB_COMM)>;
> +			sink-pdos = <PDO_FIXED(5000, 500, PDO_FIXED_USB_COMM)
> +				PDO_VAR(5000, 5000, 1000)>;
> +			op-sink-microwatt = <10000000>;
> +
> +			ports {
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				port@1 {
> +					reg = <1>;
> +					usb_con_ss: endpoint {
> +						remote-endpoint = <&dwc3_ss>;
> +					};
> +				};
> +			};
> +		};
> +		port {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			rt1711h_ep: endpoint@0 {
> +				reg = <0>;
> +				remote-endpoint = <&hikey_usb_ep1>;
> +			};
> +		};
> +	};
> +};
> +
> +&i2c2 {
> +	/* USB HUB is on this bus at address 0x44 */
> +	status = "okay";
> +};
> +
> +&dwc3 { /* USB */
> +	dr_mode = "otg";
> +	maximum-speed = "super-speed";
> +	phy_type = "utmi";
> +	snps,dis-del-phy-power-chg-quirk;
> +	snps,dis_u2_susphy_quirk;
> +	snps,dis_u3_susphy_quirk;
> +	snps,tx_de_emphasis_quirk;
> +	snps,tx_de_emphasis = <1>;
> +	snps,dis-split-quirk;
> +	snps,gctl-reset-quirk;
> +	usb-role-switch;
> +	role-switch-default-mode = "host";
> +	port {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		dwc3_role_switch: endpoint@0 {
> +			reg = <0>;
> +			remote-endpoint = <&hikey_usb_ep0>;
> +		};
> +
> +		dwc3_ss: endpoint@1 {
> +			reg = <1>;
> +			remote-endpoint = <&usb_con_ss>;
> +		};
> +	};
> +};
> diff --git a/arch/arm64/boot/dts/hisilicon/hi3670.dtsi b/arch/arm64/boot/dts/hisilicon/hi3670.dtsi
> index 20698cfd0637..1f228612192c 100644
> --- a/arch/arm64/boot/dts/hisilicon/hi3670.dtsi
> +++ b/arch/arm64/boot/dts/hisilicon/hi3670.dtsi
> @@ -8,6 +8,7 @@
>  
>  #include <dt-bindings/interrupt-controller/arm-gic.h>
>  #include <dt-bindings/clock/hi3670-clock.h>
> +#include <dt-bindings/usb/pd.h>
>  
>  / {
>  	compatible = "hisilicon,hi3670";
> @@ -785,5 +786,60 @@ i2c4: i2c@fdf0d000 {
>  			pinctrl-0 = <&i2c4_pmx_func &i2c4_cfg_func>;
>  			status = "disabled";
>  		};
> +
> +		usb3_otg_bc: usb3_otg_bc@ff200000 {
> +			compatible = "syscon", "simple-mfd";
> +			reg = <0x0 0xff200000 0x0 0x1000>;
> +
> +			usb_phy: usbphy {
> +				compatible = "hisilicon,hi3670-usb-phy";
> +				#phy-cells = <0>;
> +				hisilicon,pericrg-syscon = <&crg_ctrl>;
> +				hisilicon,pctrl-syscon = <&pctrl>;
> +				hisilicon,sctrl-syscon = <&sctrl>;
> +				hisilicon,eye-diagram-param = <0xFDFEE4>;
> +				hisilicon,tx-vboost-lvl = <0x5>;
> +			};
> +		};
> +
> +		usb31_misc_rst: usb31_misc_rst_controller {
> +			compatible = "hisilicon,hi3660-reset";
> +			#reset-cells = <2>;
> +			hisi,rst-syscon = <&usb3_otg_bc>;
> +		};
> +
> +		usb3: hisi_dwc3 {
> +			compatible = "hisilicon,hi3670-dwc3";
> +			#address-cells = <2>;
> +			#size-cells = <2>;
> +			ranges;
> +
> +			clocks = <&crg_ctrl HI3670_CLK_GATE_ABB_USB>,
> +				  <&crg_ctrl HI3670_HCLK_GATE_USB3OTG>,
> +				  <&crg_ctrl HI3670_CLK_GATE_USB3OTG_REF>,
> +				  <&crg_ctrl HI3670_ACLK_GATE_USB3DVFS>;
> +			clock-names = "clk_gate_abb_usb",
> +				      "hclk_gate_usb3otg",
> +				      "clk_gate_usb3otg_ref",
> +				      "aclk_gate_usb3dvfs";
> +
> +			assigned-clocks = <&crg_ctrl HI3670_ACLK_GATE_USB3DVFS>;
> +			assigned-clock-rates = <238000000>;
> +			resets = <&crg_rst 0x90 6>,
> +				 <&crg_rst 0x90 7>,
> +				 <&usb31_misc_rst 0xA0 8>,
> +				 <&usb31_misc_rst 0xA0 9>;
> +
> +			dwc3: usb@ff100000 {
> +				compatible = "snps,dwc3";
> +				reg = <0x0 0xff100000 0x0 0x100000>;
> +
> +				interrupts = <0 159 IRQ_TYPE_LEVEL_HIGH>,
> +					    <0 161 IRQ_TYPE_LEVEL_HIGH>;
> +
> +				phys = <&usb_phy>;
> +				phy-names = "usb3-phy";
> +			};
> +		};
>  	};
>  };
>