Re: [net-next PATCH v11 3/9] dt-bindings: net: dsa: Document support for Airoha AN8855 DSA Switch

[Christian Marangi <ansuelsmth@gmail.com>]

On Tue, Dec 10, 2024 at 10:48:55PM +0200, Vladimir Oltean wrote:
> On Mon, Dec 09, 2024 at 02:44:20PM +0100, Christian Marangi wrote:
> > Document support for Airoha AN8855 5-port Gigabit Switch.
> > 
> > It does expose the 5 Internal PHYs on the MDIO bus and each port
> > can access the Switch register space by configurting the PHY page.
> 
> typo: configuring
> Also below.
> 
> > 
> > Each internal PHY might require calibration with the fused EFUSE on
> > the switch exposed by the Airoha AN8855 SoC NVMEM.
> 
> This paragraph should be irrelevant to the switch binding.
> 
> > 
> > Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
> > ---
> >  .../net/dsa/airoha,an8855-switch.yaml         | 105 ++++++++++++++++++
> >  MAINTAINERS                                   |   1 +
> >  2 files changed, 106 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/net/dsa/airoha,an8855-switch.yaml
> > 
> > diff --git a/Documentation/devicetree/bindings/net/dsa/airoha,an8855-switch.yaml b/Documentation/devicetree/bindings/net/dsa/airoha,an8855-switch.yaml
> > new file mode 100644
> > index 000000000000..63bcbebd6a29
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/net/dsa/airoha,an8855-switch.yaml
> > @@ -0,0 +1,105 @@
> > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/net/dsa/airoha,an8855-switch.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: Airoha AN8855 Gigabit Switch
> > +
> > +maintainers:
> > +  - Christian Marangi <ansuelsmth@gmail.com>
> > +
> > +description: >
> > +  Airoha AN8855 is a 5-port Gigabit Switch.
> > +
> > +  It does expose the 5 Internal PHYs on the MDIO bus and each port
> > +  can access the Switch register space by configurting the PHY page.
> > +
> > +  Each internal PHY might require calibration with the fused EFUSE on
> > +  the switch exposed by the Airoha AN8855 SoC NVMEM.
> > +
> > +$ref: dsa.yaml#
> > +
> > +properties:
> > +  compatible:
> > +    const: airoha,an8855-switch
> > +
> > +  reset-gpios:
> > +    description:
> > +      GPIO to be used to reset the whole device
> > +    maxItems: 1
> 
> Since this affects the whole device, the SoC node (handled by the
> MFD driver) should handle it. Otherwise you expose the code to weird
> race conditions where one child MFD device resets the whole chip after
> the other MFD children have probed, and this undoes their settings.
>

OK.

> > +
> > +  airoha,ext-surge:
> > +    $ref: /schemas/types.yaml#/definitions/flag
> > +    description:
> > +      Calibrate the internal PHY with the calibration values stored in EFUSE
> > +      for the r50Ohm values.
> 
> Doesn't seem that this pertains to the switch.

Do you think this should be placed in each PHY node? I wanted to prevent
having to define a schema also for PHY if possible given how integrated
these are. (originally it was defined in DT node to follow how it was
done in Airoha SDK)

-- 
	Ansuel