Re: [PATCH V7 6/9] mmc: sdhci: Add Auto CMD Auto Select support

[Adrian Hunter <adrian.hunter@intel.com>]

On 29/08/18 10:03, Chunyan Zhang wrote:
> As SD Host Controller Specification v4.10 documents:
> Host Controller Version 4.10 defines this "Auto CMD Auto Select" mode.
> Selection of Auto CMD depends on setting of CMD23 Enable in the Host
> Control 2 register which indicates whether card supports CMD23. If CMD23
> Enable =1, Auto CMD23 is used and if CMD23 Enable =0, Auto CMD12 is
> used. In case of Version 4.10 or later, use of Auto CMD Auto Select is
> recommended rather than use of Auto CMD12 Enable or Auto CMD23
> Enable.
> 
> This patch add this new mode support.
> 
> Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>

Acked-by: Adrian Hunter <adrian.hunter@intel.com>

> ---
>  drivers/mmc/host/sdhci.c | 49 ++++++++++++++++++++++++++++++++++++++----------
>  drivers/mmc/host/sdhci.h |  2 ++
>  2 files changed, 41 insertions(+), 10 deletions(-)
> 
> diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
> index 604bf4c..62d843ac90 100644
> --- a/drivers/mmc/host/sdhci.c
> +++ b/drivers/mmc/host/sdhci.c
> @@ -1095,6 +1095,43 @@ static inline bool sdhci_auto_cmd12(struct sdhci_host *host,
>  	       !mrq->cap_cmd_during_tfr;
>  }
>  
> +static inline void sdhci_auto_cmd_select(struct sdhci_host *host,
> +					 struct mmc_command *cmd,
> +					 u16 *mode)
> +{
> +	bool use_cmd12 = sdhci_auto_cmd12(host, cmd->mrq) &&
> +			 (cmd->opcode != SD_IO_RW_EXTENDED);
> +	bool use_cmd23 = cmd->mrq->sbc && (host->flags & SDHCI_AUTO_CMD23);
> +	u16 ctrl2;
> +
> +	/*
> +	 * In case of Version 4.10 or later, use of 'Auto CMD Auto
> +	 * Select' is recommended rather than use of 'Auto CMD12
> +	 * Enable' or 'Auto CMD23 Enable'.
> +	 */
> +	if (host->version >= SDHCI_SPEC_410 && (use_cmd12 || use_cmd23)) {
> +		*mode |= SDHCI_TRNS_AUTO_SEL;
> +
> +		ctrl2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
> +		if (use_cmd23)
> +			ctrl2 |= SDHCI_CMD23_ENABLE;
> +		else
> +			ctrl2 &= ~SDHCI_CMD23_ENABLE;
> +		sdhci_writew(host, ctrl2, SDHCI_HOST_CONTROL2);
> +
> +		return;
> +	}
> +
> +	/*
> +	 * If we are sending CMD23, CMD12 never gets sent
> +	 * on successful completion (so no Auto-CMD12).
> +	 */
> +	if (use_cmd12)
> +		*mode |= SDHCI_TRNS_AUTO_CMD12;
> +	else if (use_cmd23)
> +		*mode |= SDHCI_TRNS_AUTO_CMD23;
> +}
> +
>  static void sdhci_set_transfer_mode(struct sdhci_host *host,
>  	struct mmc_command *cmd)
>  {
> @@ -1123,17 +1160,9 @@ static void sdhci_set_transfer_mode(struct sdhci_host *host,
>  
>  	if (mmc_op_multi(cmd->opcode) || data->blocks > 1) {
>  		mode = SDHCI_TRNS_BLK_CNT_EN | SDHCI_TRNS_MULTI;
> -		/*
> -		 * If we are sending CMD23, CMD12 never gets sent
> -		 * on successful completion (so no Auto-CMD12).
> -		 */
> -		if (sdhci_auto_cmd12(host, cmd->mrq) &&
> -		    (cmd->opcode != SD_IO_RW_EXTENDED))
> -			mode |= SDHCI_TRNS_AUTO_CMD12;
> -		else if (cmd->mrq->sbc && (host->flags & SDHCI_AUTO_CMD23)) {
> -			mode |= SDHCI_TRNS_AUTO_CMD23;
> +		sdhci_auto_cmd_select(host, cmd, &mode);
> +		if (cmd->mrq->sbc && (host->flags & SDHCI_AUTO_CMD23))
>  			sdhci_writel(host, cmd->mrq->sbc->arg, SDHCI_ARGUMENT2);
> -		}
>  	}
>  
>  	if (data->flags & MMC_DATA_READ)
> diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h
> index f7a1079..4a19ff8 100644
> --- a/drivers/mmc/host/sdhci.h
> +++ b/drivers/mmc/host/sdhci.h
> @@ -42,6 +42,7 @@
>  #define  SDHCI_TRNS_BLK_CNT_EN	0x02
>  #define  SDHCI_TRNS_AUTO_CMD12	0x04
>  #define  SDHCI_TRNS_AUTO_CMD23	0x08
> +#define  SDHCI_TRNS_AUTO_SEL	0x0C
>  #define  SDHCI_TRNS_READ	0x10
>  #define  SDHCI_TRNS_MULTI	0x20
>  
> @@ -185,6 +186,7 @@
>  #define   SDHCI_CTRL_DRV_TYPE_D		0x0030
>  #define  SDHCI_CTRL_EXEC_TUNING		0x0040
>  #define  SDHCI_CTRL_TUNED_CLK		0x0080
> +#define  SDHCI_CMD23_ENABLE		0x0800
>  #define  SDHCI_CTRL_V4_MODE		0x1000
>  #define  SDHCI_CTRL_64BIT_ADDR		0x2000
>  #define  SDHCI_CTRL_PRESET_VAL_ENABLE	0x8000
>