* v2.4.4 PCI IRQ 0 / help wanted
@ 2001-04-30 2:54 Narang
2001-05-01 2:37 ` 2.4.4: USB HC TakeOver failed! Narang
0 siblings, 1 reply; 2+ messages in thread
From: Narang @ 2001-04-30 2:54 UTC (permalink / raw)
To: linux-kernel
. If a device is not found by BIOS can it still be used?
. Why is the USB device getting IRQ 0?
. Why is the Firewire device 8020 unknown?
Attached is output of lspci, syslog, and output of lspci -vv.
Hoping I can get some help. Please CC me any suggestions. Thanks.
lspci
--------
00:00.0 Host bridge: VLSI Technology Inc 82C592-FC1 (rev 01)
00:01.0 ISA bridge: VLSI Technology Inc 82C593-FC1 (rev 01)
00:0d.0 IDE interface: CMD Technology Inc PCI0640 (rev 02)
00:10.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 03)
00:11.0 VGA compatible controller: S3 Inc. 86c764/765 [Trio32/64/64V+]
00:12.0 SCSI storage controller: BusLogic BT-946C (BA80C30) [MultiMaster 10]
01:04.0 USB Controller: CMD Technology Inc USB0670 (rev 06)
>>>>> 01:05.0 FireWire (IEEE 1394): Texas Instruments: Unknown device 8020
>From syslog
-----------
Apr 29 17:56:03 shakti kernel: PCI: PCI BIOS revision 2.00 entry at 0xfc9bb, last bus=0
Apr 29 17:56:03 shakti kernel: PCI: Using configuration type 1
Apr 29 17:56:03 shakti kernel: PCI: Probing PCI hardware
Apr 29 17:56:03 shakti kernel: Unknown bridge resource 0: assuming transparent
Apr 29 17:56:03 shakti kernel: Unknown bridge resource 1: assuming transparent
Apr 29 17:56:03 shakti kernel: Unknown bridge resource 2: assuming transparent
>>>>> Apr 29 17:56:03 shakti kernel: PCI: Device 01:20 not found by BIOS
>>>>> Apr 29 17:56:03 shakti kernel: PCI: Device 01:28 not found by BIOS
...
Apr 29 17:56:06 shakti kernel: usb.c: registered new driver usbdevfs
Apr 29 17:56:06 shakti kernel: usb.c: registered new driver hub
>>>>> Apr 29 17:56:06 shakti kernel: PCI: No IRQ known for interrupt pin A of device 01:04.0. Please try using pci=biosirq.
Apr 29 17:56:06 shakti kernel: PCI: Setting latency timer of device 01:04.0 to 64
Apr 29 17:56:06 shakti kernel: usb-ohci.c: USB OHCI at membase 0xc8917000, IRQ 0
Apr 29 17:56:06 shakti kernel: usb-ohci.c: usb-01:04.0, CMD Technology Inc USB0670
Apr 29 17:56:08 shakti kernel: usb-ohci.c: USB HC TakeOver failed!
Apr 29 17:56:08 shakti kernel: usb.c: USB bus -1 deregistered
Apr 29 17:56:08 shakti kernel: usb.c: deregistering driver usbdevfs
Apr 29 17:56:08 shakti kernel: usb.c: deregistering driver hub
lspci -vv
---------
00:00.0 Host bridge: VLSI Technology Inc 82C592-FC1 (rev 01)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Latency: 16
00:01.0 ISA bridge: VLSI Technology Inc 82C593-FC1 (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:0d.0 IDE interface: CMD Technology Inc PCI0640 (rev 02) (prog-if 0a [SecP PriP])
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 14
00:10.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 03) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00000000-00000fff
Memory behind bridge: 00000000-000fffff
Prefetchable memory behind bridge: 0000000000000000-0000000000000000
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: <available only to root>
00:11.0 VGA compatible controller: S3 Inc. 86c764/765 [Trio32/64/64V+] (prog-if 00 [VGA])
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 40000000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at 20000000 [disabled] [size=64K]
00:12.0 SCSI storage controller: BusLogic BT-946C (BA80C30) [MultiMaster 10]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 240, cache line size 04
Interrupt: pin C routed to IRQ 15
Region 0: I/O ports at fcfc [size=4]
Expansion ROM at ff000000 [disabled] [size=16K]
01:04.0 USB Controller: CMD Technology Inc USB0670 (rev 06) (prog-if 10 [OHCI])
Subsystem: CMD Technology Inc USB0670
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (500ns min, 1000ns max)
Interrupt: pin A routed to IRQ 0
Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <available only to root>
01:05.0 FireWire (IEEE 1394): Texas Instruments: Unknown device 8020 (prog-if 10 [OHCI])
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 0
Region 0: Memory at 10001000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at 10004000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <available only to root>
^ permalink raw reply [flat|nested] 2+ messages in thread
* 2.4.4: USB HC TakeOver failed!
2001-04-30 2:54 v2.4.4 PCI IRQ 0 / help wanted Narang
@ 2001-05-01 2:37 ` Narang
0 siblings, 0 replies; 2+ messages in thread
From: Narang @ 2001-05-01 2:37 UTC (permalink / raw)
To: linux-kernel
Does anyone has any suggestions on fixing 'USB HC TakeOver failed!'
problem. thanks.
syslog
------
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Setting latency timer of device 01:04.0 to 64
usb-ohci.c: USB OHCI at membase 0xc8914000, IRQ 8
usb-ohci.c: usb-01:04.0, CMD Technology Inc USB0670
>>>> usb-ohci.c: USB HC TakeOver failed!
usb.c: USB bus -1 deregistered
usb.c: deregistering driver usbdevfs
usb.c: deregistering driver hub
lspci -vv -s 01:04
------------------
01:04.0 USB Controller: CMD Technology Inc USB0670 (rev 06) (prog-if 10 [OHCI])
Subsystem: CMD Technology Inc USB0670
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (500ns min, 1000ns max)
Interrupt: pin A routed to IRQ 8
Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
lspci
--------
00:00.0 Host bridge: VLSI Technology Inc 82C592-FC1 (rev 01)
00:01.0 ISA bridge: VLSI Technology Inc 82C593-FC1 (rev 01)
00:0d.0 IDE interface: CMD Technology Inc PCI0640 (rev 02)
00:10.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 03)
00:11.0 VGA compatible controller: S3 Inc. 86c764/765 [Trio32/64/64V+]
00:12.0 SCSI storage controller: BusLogic BT-946C (BA80C30) [MultiMaster 10]
01:04.0 USB Controller: CMD Technology Inc USB0670 (rev 06)
01:05.0 FireWire (IEEE 1394): Texas Instruments: Unknown device 8020
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2001-05-01 2:37 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2001-04-30 2:54 v2.4.4 PCI IRQ 0 / help wanted Narang
2001-05-01 2:37 ` 2.4.4: USB HC TakeOver failed! Narang
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox