[PATCH v8 0/8] gpio: renesas: Add support for GPIO and related interrupts in RZ/N1 SoC

[PATCH v8 0/8] gpio: renesas: Add support for GPIO and related interrupts in RZ/N1 SoC

[Herve Codina (Schneider Electric)]

Hi,

This series adds support for GPIO and GPIO IRQ mux available in the
RZ/N1 SoCs.

The first patches in this series are related to a new helper introduced
to parse an interrupt-map property.
  - patch 1: Introduce the helper (for_each_of_imap_item)
  - patch 2: Add a unittest for the new helper
  - patch 3 and 4: convert existing drivers to use this new helper

Patch 5 adds support for GPIO (device-tree description)

The last patches (6, 7 and 8) of the series are related to GPIO
interrupts and GPIO IRQ multiplexer.

In the RZ/N1 SoCs, GPIO interrupts are wired to a GPIO IRQ multiplexer.

This multiplexer does nothing but select 8 GPIO IRQ lines out of the 96
available to wire them to the GIC input lines.

One upstreaming attempt have been done previously by Phil Edworthy [1]
but the series has never been applied.

Based on my understanding, I have fully reworked the driver proposed by
Phil and removed the IRQ domain. Indeed, the device doesn't handle
interrupts. It just routes signals.

Also, as an interrupt-map property is used, the driver cannot be
involved as an interrupt controller itself. It is a nexus node.

With that in mind,
  - Patch 6 is related to the irq-mux binding.

  - Patch 7 introduces the irq-mux driver.
    This driver uses the 'for_each_of_imap_item' helper introduced
    previously. Indeed, the lines routing is defined by the
    interrupt-map property and the driver needs to set registers to
    apply this routing.

  - Patch 8 is the RZ/N1 device-tree description update to have the
    support for the GPIO interrupts.

The series was already ready in its v7 iteration. This v8 iteration just
add the 'Tested-by' tag sent by Wolfram on v7.

Even if the series touches several subsystems, the whole series could be
merged through the renesas-devel tree as suggested in the v7 iteration
[2].

Rob, Thomas, this series is blocked waiting for your feedback and your
acks if you are okay.

[1] https://lore.kernel.org/all/20190219155511.28507-1-phil.edworthy@renesas.com/
[2] https://lore.kernel.org/all/aV6wcIE0D7ozKeQn@ninjato/

Best regards,
Hervé

Changes v7 -> v8
  v7: https://lore.kernel.org/all/20251215142836.167101-1-herve.codina@bootlin.com/

  Patches 1 to 7:
   - No changes

  Patch 8:
   - Add 'Tested-by: Wolfram Sang'.

Changes v6 -> v7
  v6: https://lore.kernel.org/all/20251027123601.77216-1-herve.codina@bootlin.com/

  Rebase on top of v6.19-rc1.

  Patches 1 to 4 :
   - Add 'Reviewed-by: Linus Walleij'.

  Patch 5:
   - Fix a typo (Synopsys) in commit log.
   - GPIO controllers enabled by default.
   - Move "reg" just below "compatible".
   - Add 'Reviewed-by: Linus Walleij'.
   - Add 'Reviewed-by: Geert Uytterhoeven'.

  Patch 6:
   - Add 'Reviewed-by: Linus Walleij'.
   - Add 'Reviewed-by: Geert Uytterhoeven'.

  Patch 7:
   - Enable RZN1_IRQMUX only if GPIO_DWAPB is enabled.
   - Move a 'if' condition to a single line.
   - Print the output line index in the 'already defined' error message.
   - Move rzn1_irqmux_setup() code directly into rzn1_irqmux_probe().
   - Add 'Reviewed-by: Linus Walleij'.
   - Add 'Tested-by: Wolfram Sang'.
   - Add 'Reviewed-by: Wolfram Sang'.
   - Add 'Reviewed-by: Geert Uytterhoeven'.

  Patch 8:
   - Remove unneeded spaces.
   - Add 'Reviewed-by: Linus Walleij'
   - Add 'Reviewed-by: Wolfram Sang'
   - Add 'Reviewed-by: Geert Uytterhoeven'

Changes v5 -> v6
  v5: https://lore.kernel.org/lkml/20251020080648.13452-1-herve.codina@bootlin.com/

  Patches 1 and 2:
    Add 'Reviewed-by: Rob Herring'

  Patches 3, and 5:
    No changes

  Patch 6:
    Add 'Reviewed-by: Rob Herring'

  Patch 7:
    Remove an unneeded TAB in Makefile.
    Use RZN1_IRQMUX_GIC_SPI_BASE and RZN1_IRQMUX_NUM_OUTPUTS to replace
    the irq/output mapping table.
    Use DECLARE_BITMAP().

  Patch 8:
    No changes

Changes v4 -> v5
  v4: https://lore.kernel.org/lkml/20250922152640.154092-1-herve.codina@bootlin.com/

  Rebase on top of v6.18-rc1

  Patches 1 to 3:
    No changes

  Patch 4:
    Fix conflict.
    Add 'Tested-by: Wolfram Sang'.

  Patch 5:
    Add 'Reviewed-by: Bartosz Golaszewski'.

  Patch 6:
    Add 'Reviewed-by: Wolfram Sang'.

  Patch 7:
    Add a missing 'const' qualifier.
    Remove an unneeded dev_err_probe() call.
    Add a check to avoid setting the same output line multiple times.

  Patch 8:
    Update comment
    Add 'Reviewed-by: Bartosz Golaszewski'

Changes v3 -> v4
  v3: https://lore.kernel.org/lkml/20250918104009.94754-1-herve.codina@bootlin.com/

  Patch 1:
    - Add 'Tested-by: Wolfram Sang'

  Patch 2..5:
    - No changes

  Patch 6:
    - Add minItems and maxItems
    - Update the 'interrup-map' description

  Patch 7:
    - Use rzn1_irqmux prefix instead of irqmux.
    - Introduce rzn1_irqmux_output_lines[] to give the mapping between
      the interrupt output line index and the GIC controller interrupt
      number.
    - Remove of_irq_count() call and related checks

  Patch 8:
    - Describe the irq mux node using a reduced (one item) interrupt-map
      property.

Changes v2 -> v3
  v2: https://lore.kernel.org/lkml/20250909120041.154459-1-herve.codina@bootlin.com/

  Reordered patches as suggested by Thomas Gleixner.

  Patch 1: (3 in v2)
    - Replace a wrong 'extern' by 'static inline' in of_irq.h  (detected
      by test robots)

  Patch 2: (4 in v2)
  Patch 3: (5 in v2)
  Patch 4: (6 in v2)
    - No changes

  Patch 5: (1 in v2)
    - Add 'Reviewed-by: Wolfram Sang'
    - Add 'Tested-by: Wolfram Sang'

  Patch 6: (2 in v2)
    - Add '#address-cells = <0>;' in the interrupt-controller node
      present in the example.

  Patch 7:
  Patch 8:
    - No changes

Changes v1 -> v2
  v1: https://lore.kernel.org/lkml/20250725152618.32886-1-herve.codina@bootlin.com/

  Rebase on top of v6.17-rc5

  Patch 1 in v1
    - Removed in v2 (no need for RZ/N1 compatible strings).

  Patch 1 (2 in v1)
    - Fix node names (issue reported by Rob's bot)
    - Fix compatible RZ/N1 compatible strings
    - Removed undocumented and unused 'bank-name' properties

  Patch 2 (3 in v1)
   - Remove 'interrupts' property
   - Update 'interrupt-map' description

  Patch 3 (4 in v1)
   - Rework of_irq_foreach_imap() to provide the for_each_of_imap_item
     iterator (similar to for_each_of_range)

  Patch 4 (new in v2)
   - Add a unittest for for_each_of_imap_item

  Patch 5 (new in v2)
   - Convert irqchip/ls-extirq to use for_each_of_imap_item

  Patch 6 (new in v2)
   - Convert irqchip/renesas-rza1 to use for_each_of_imap_item

  Patch 7 (5 in v1)
   - Use for_each_of_imap_item
   - Remove 'interrupts' property usage

  Patch 8 (6 in v1)
   - Remove 'interrupts' property

Herve Codina (Schneider Electric) (8):
  of/irq: Introduce for_each_of_imap_item
  of: unittest: Add a test case for for_each_of_imap_item iterator
  irqchip/ls-extirq: Use for_each_of_imap_item iterator
  irqchip/renesas-rza1: Use for_each_of_imap_item iterator
  ARM: dts: r9a06g032: Add GPIO controllers
  dt-bindings: soc: renesas: Add the Renesas RZ/N1 GPIO Interrupt
    Multiplexer
  soc: renesas: Add support for Renesas RZ/N1 GPIO Interrupt Multiplexer
  ARM: dts: r9a06g032: Add support for GPIO interrupts

 .../soc/renesas/renesas,rzn1-gpioirqmux.yaml  |  87 ++++++++++
 arch/arm/boot/dts/renesas/r9a06g032.dtsi      | 159 ++++++++++++++++++
 drivers/irqchip/irq-ls-extirq.c               |  47 ++----
 drivers/irqchip/irq-renesas-rza1.c            |  43 ++---
 drivers/of/irq.c                              |  70 ++++++++
 .../of/unittest-data/tests-interrupts.dtsi    |   9 +
 drivers/of/unittest.c                         | 116 +++++++++++++
 drivers/soc/renesas/Kconfig                   |   4 +
 drivers/soc/renesas/Makefile                  |   1 +
 drivers/soc/renesas/rzn1_irqmux.c             | 127 ++++++++++++++
 include/linux/of_irq.h                        |  41 ++++-
 11 files changed, 646 insertions(+), 58 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/soc/renesas/renesas,rzn1-gpioirqmux.yaml
 create mode 100644 drivers/soc/renesas/rzn1_irqmux.c

-- 
2.52.0

[PATCH v8 1/8] of/irq: Introduce for_each_of_imap_item

[Herve Codina (Schneider Electric)]

for_each_of_imap_item is an iterator designed to help a driver to parse
an interrupt-map property.

Indeed some drivers need to know details about the interrupt mapping
described in the device-tree in order to set internal registers
accordingly.

Signed-off-by: Herve Codina (Schneider Electric) <herve.codina@bootlin.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
---
 drivers/of/irq.c       | 70 ++++++++++++++++++++++++++++++++++++++++++
 include/linux/of_irq.h | 41 ++++++++++++++++++++++++-
 2 files changed, 110 insertions(+), 1 deletion(-)

diff --git a/drivers/of/irq.c b/drivers/of/irq.c
index e3816819dbfe..f374d8b212b8 100644
--- a/drivers/of/irq.c
+++ b/drivers/of/irq.c
@@ -157,6 +157,76 @@ const __be32 *of_irq_parse_imap_parent(const __be32 *imap, int len, struct of_ph
 	return imap;
 }
 
+int of_imap_parser_init(struct of_imap_parser *parser, struct device_node *node,
+			struct of_imap_item *item)
+{
+	int imaplen;
+	u32 tmp;
+	int ret;
+
+	/*
+	 * parent_offset is the offset where the parent part is starting.
+	 * In other words, the offset where the parent interrupt controller
+	 * phandle is present.
+	 *
+	 * Compute this offset (child #interrupt-cells + child #address-cells)
+	 */
+	parser->parent_offset = of_bus_n_addr_cells(node);
+
+	ret = of_property_read_u32(node, "#interrupt-cells", &tmp);
+	if (ret)
+		return ret;
+
+	parser->parent_offset += tmp;
+
+	if (WARN(parser->parent_offset > ARRAY_SIZE(item->child_imap),
+		 "child part size = %u, cannot fit in array of %zu items",
+		 parser->parent_offset, ARRAY_SIZE(item->child_imap)))
+		return -EINVAL;
+
+	parser->imap = of_get_property(node, "interrupt-map", &imaplen);
+	if (!parser->imap)
+		return -ENOENT;
+
+	imaplen /= sizeof(*parser->imap);
+	parser->imap_end = parser->imap + imaplen;
+
+	memset(item, 0, sizeof(*item));
+	item->child_imap_count = parser->parent_offset;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(of_imap_parser_init);
+
+struct of_imap_item *of_imap_parser_one(struct of_imap_parser *parser,
+					struct of_imap_item *item)
+{
+	const __be32 *imap_parent, *imap_next;
+	int i;
+
+	/* Release previously get parent node */
+	of_node_put(item->parent_args.np);
+
+	if (parser->imap + parser->parent_offset + 1 >= parser->imap_end)
+		return NULL;
+
+	imap_parent = parser->imap + parser->parent_offset;
+
+	imap_next = of_irq_parse_imap_parent(imap_parent,
+					     parser->imap_end - imap_parent,
+					     &item->parent_args);
+	if (!imap_next)
+		return NULL;
+
+	for (i = 0; i < parser->parent_offset; i++)
+		item->child_imap[i] = be32_to_cpu(*(parser->imap + i));
+
+	parser->imap = imap_next;
+
+	return item;
+}
+EXPORT_SYMBOL_GPL(of_imap_parser_one);
+
 /**
  * of_irq_parse_raw - Low level interrupt tree parsing
  * @addr:	address specifier (start of "reg" property of the device) in be32 format
diff --git a/include/linux/of_irq.h b/include/linux/of_irq.h
index 1c2bc0281807..2a64d8cecaae 100644
--- a/include/linux/of_irq.h
+++ b/include/linux/of_irq.h
@@ -11,6 +11,30 @@
 
 typedef int (*of_irq_init_cb_t)(struct device_node *, struct device_node *);
 
+struct of_imap_parser {
+	struct device_node *node;
+	const __be32 *imap;
+	const __be32 *imap_end;
+	u32 parent_offset;
+};
+
+struct of_imap_item {
+	struct of_phandle_args parent_args;
+	u32 child_imap_count;
+	u32 child_imap[16]; /* Arbitrary size.
+			     * Should be #address-cells + #interrupt-cells but
+			     * avoid using allocation and so, expect that 16
+			     * should be enough
+			     */
+};
+
+/*
+ * If the iterator is exited prematurely (break, goto, return) of_node_put() has
+ * to be called on item.parent_args.np
+ */
+#define for_each_of_imap_item(parser, item) \
+	for (; of_imap_parser_one(parser, item);)
+
 /*
  * Workarounds only applied to 32bit powermac machines
  */
@@ -49,6 +73,11 @@ extern int of_irq_get_byname(struct device_node *dev, const char *name);
 extern int of_irq_to_resource_table(struct device_node *dev,
 		struct resource *res, int nr_irqs);
 extern struct device_node *of_irq_find_parent(struct device_node *child);
+extern int of_imap_parser_init(struct of_imap_parser *parser,
+			       struct device_node *node,
+			       struct of_imap_item *item);
+extern struct of_imap_item *of_imap_parser_one(struct of_imap_parser *parser,
+					       struct of_imap_item *item);
 extern struct irq_domain *of_msi_get_domain(struct device *dev,
 					    const struct device_node *np,
 					    enum irq_domain_bus_token token);
@@ -92,7 +121,17 @@ static inline void *of_irq_find_parent(struct device_node *child)
 {
 	return NULL;
 }
-
+static inline int of_imap_parser_init(struct of_imap_parser *parser,
+				      struct device_node *node,
+				      struct of_imap_item *item)
+{
+	return -ENOSYS;
+}
+static inline struct of_imap_item *of_imap_parser_one(struct of_imap_parser *parser,
+						      struct of_imap_item *item)
+{
+	return NULL;
+}
 static inline struct irq_domain *of_msi_get_domain(struct device *dev,
 						   struct device_node *np,
 						   enum irq_domain_bus_token token)
-- 
2.52.0

[PATCH v8 2/8] of: unittest: Add a test case for for_each_of_imap_item iterator

[Herve Codina (Schneider Electric)]

Recently for_each_of_imap_item iterator has been introduce to help
drivers in parsing the interrupt-map property.

Add a test case for this iterator.

Signed-off-by: Herve Codina (Schneider Electric) <herve.codina@bootlin.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
---
 .../of/unittest-data/tests-interrupts.dtsi    |   9 ++
 drivers/of/unittest.c                         | 116 ++++++++++++++++++
 2 files changed, 125 insertions(+)

diff --git a/drivers/of/unittest-data/tests-interrupts.dtsi b/drivers/of/unittest-data/tests-interrupts.dtsi
index 4ccb54f91c30..974f888c9b15 100644
--- a/drivers/of/unittest-data/tests-interrupts.dtsi
+++ b/drivers/of/unittest-data/tests-interrupts.dtsi
@@ -50,6 +50,15 @@ test_intmap1: intmap1 {
 				interrupt-map = <0x5000 1 2 &test_intc0 15>;
 			};
 
+			intmap2 {
+				#interrupt-cells = <2>;
+				#address-cells = <0>;
+				interrupt-map = <1 11 &test_intc0 100>,
+						<2 22 &test_intc1 200 201 202>,
+						<3 33 &test_intc2 300 301>,
+						<4 44 &test_intc2 400 401>;
+			};
+
 			test_intc_intmap0: intc-intmap0 {
 				#interrupt-cells = <1>;
 				#address-cells = <1>;
diff --git a/drivers/of/unittest.c b/drivers/of/unittest.c
index 388e9ec2cccf..d88a12f23ad5 100644
--- a/drivers/of/unittest.c
+++ b/drivers/of/unittest.c
@@ -1654,6 +1654,121 @@ static void __init of_unittest_parse_interrupts_extended(void)
 	of_node_put(np);
 }
 
+struct of_unittest_expected_imap_item {
+	u32 child_imap_count;
+	u32 child_imap[2];
+	const char *parent_path;
+	int parent_args_count;
+	u32 parent_args[3];
+};
+
+static const struct of_unittest_expected_imap_item of_unittest_expected_imap_items[] = {
+	{
+		.child_imap_count = 2,
+		.child_imap = {1, 11},
+		.parent_path = "/testcase-data/interrupts/intc0",
+		.parent_args_count = 1,
+		.parent_args = {100},
+	}, {
+		.child_imap_count = 2,
+		.child_imap = {2, 22},
+		.parent_path = "/testcase-data/interrupts/intc1",
+		.parent_args_count = 3,
+		.parent_args = {200, 201, 202},
+	}, {
+		.child_imap_count = 2,
+		.child_imap = {3, 33},
+		.parent_path = "/testcase-data/interrupts/intc2",
+		.parent_args_count = 2,
+		.parent_args = {300, 301},
+	}, {
+		.child_imap_count = 2,
+		.child_imap = {4, 44},
+		.parent_path = "/testcase-data/interrupts/intc2",
+		.parent_args_count = 2,
+		.parent_args = {400, 401},
+	}
+};
+
+static void __init of_unittest_parse_interrupt_map(void)
+{
+	const struct of_unittest_expected_imap_item *expected_item;
+	struct device_node *imap_np, *expected_parent_np;
+	struct of_imap_parser imap_parser;
+	struct of_imap_item imap_item;
+	int count, ret, i;
+
+	if (of_irq_workarounds & (OF_IMAP_NO_PHANDLE | OF_IMAP_OLDWORLD_MAC))
+		return;
+
+	imap_np = of_find_node_by_path("/testcase-data/interrupts/intmap2");
+	if (!imap_np) {
+		pr_err("missing testcase data\n");
+		return;
+	}
+
+	ret = of_imap_parser_init(&imap_parser, imap_np, &imap_item);
+	if (unittest(!ret, "of_imap_parser_init(%pOF) returned error %d\n",
+		     imap_np, ret))
+		goto end;
+
+	expected_item = of_unittest_expected_imap_items;
+	count = 0;
+
+	for_each_of_imap_item(&imap_parser, &imap_item) {
+		if (unittest(count < ARRAY_SIZE(of_unittest_expected_imap_items),
+			     "imap item number %d not expected. Max number %zu\n",
+			     count, ARRAY_SIZE(of_unittest_expected_imap_items) - 1)) {
+			of_node_put(imap_item.parent_args.np);
+			goto end;
+		}
+
+		expected_parent_np = of_find_node_by_path(expected_item->parent_path);
+		if (unittest(expected_parent_np,
+			     "missing dependent testcase data (%s)\n",
+			     expected_item->parent_path)) {
+			of_node_put(imap_item.parent_args.np);
+			goto end;
+		}
+
+		unittest(imap_item.child_imap_count == expected_item->child_imap_count,
+			 "imap[%d] child_imap_count = %u, expected %u\n",
+			 count, imap_item.child_imap_count,
+			 expected_item->child_imap_count);
+
+		for (i = 0; i < expected_item->child_imap_count; i++)
+			unittest(imap_item.child_imap[i] == expected_item->child_imap[i],
+				 "imap[%d] child_imap[%d] = %u, expected %u\n",
+				 count, i, imap_item.child_imap[i],
+				 expected_item->child_imap[i]);
+
+		unittest(imap_item.parent_args.np == expected_parent_np,
+			 "imap[%d] parent np = %pOF, expected %pOF\n",
+			 count, imap_item.parent_args.np, expected_parent_np);
+
+		unittest(imap_item.parent_args.args_count == expected_item->parent_args_count,
+			 "imap[%d] parent param_count = %d, expected %d\n",
+			 count, imap_item.parent_args.args_count,
+			 expected_item->parent_args_count);
+
+		for (i = 0; i < expected_item->parent_args_count; i++)
+			unittest(imap_item.parent_args.args[i] == expected_item->parent_args[i],
+				 "imap[%d] parent param[%d] = %u, expected %u\n",
+				 count, i, imap_item.parent_args.args[i],
+				 expected_item->parent_args[i]);
+
+		of_node_put(expected_parent_np);
+		count++;
+		expected_item++;
+	}
+
+	unittest(count == ARRAY_SIZE(of_unittest_expected_imap_items),
+		 "Missing items. %d parsed, expected %zu\n",
+		 count, ARRAY_SIZE(of_unittest_expected_imap_items));
+end:
+	of_node_put(imap_np);
+}
+
 #if IS_ENABLED(CONFIG_OF_DYNAMIC)
 static void __init of_unittest_irq_refcount(void)
 {
@@ -4395,6 +4510,7 @@ static int __init of_unittest(void)
 	of_unittest_changeset_prop();
 	of_unittest_parse_interrupts();
 	of_unittest_parse_interrupts_extended();
+	of_unittest_parse_interrupt_map();
 	of_unittest_irq_refcount();
 	of_unittest_dma_get_max_cpu_address();
 	of_unittest_parse_dma_ranges();
-- 
2.52.0

[PATCH v8 3/8] irqchip/ls-extirq: Use for_each_of_imap_item iterator

[Herve Codina (Schneider Electric)]

The ls-extirq driver parses the interrupt-map property. It does it using
open code.

Recently for_each_of_imap_item iterator has been introduce to help
drivers in this parsing.

Convert the ls-extirq driver to use the for_each_of_imap_item
iterator instead of open code.

Signed-off-by: Herve Codina (Schneider Electric) <herve.codina@bootlin.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
---
 drivers/irqchip/irq-ls-extirq.c | 47 ++++++++++++---------------------
 1 file changed, 17 insertions(+), 30 deletions(-)

diff --git a/drivers/irqchip/irq-ls-extirq.c b/drivers/irqchip/irq-ls-extirq.c
index 50a7b38381b9..ed8755777349 100644
--- a/drivers/irqchip/irq-ls-extirq.c
+++ b/drivers/irqchip/irq-ls-extirq.c
@@ -125,45 +125,32 @@ static const struct irq_domain_ops extirq_domain_ops = {
 static int
 ls_extirq_parse_map(struct ls_extirq_data *priv, struct device_node *node)
 {
-	const __be32 *map;
-	u32 mapsize;
+	struct of_imap_parser imap_parser;
+	struct of_imap_item imap_item;
 	int ret;
 
-	map = of_get_property(node, "interrupt-map", &mapsize);
-	if (!map)
-		return -ENOENT;
-	if (mapsize % sizeof(*map))
-		return -EINVAL;
-	mapsize /= sizeof(*map);
+	ret = of_imap_parser_init(&imap_parser, node, &imap_item);
+	if (ret)
+		return ret;
 
-	while (mapsize) {
+	for_each_of_imap_item(&imap_parser, &imap_item) {
 		struct device_node *ipar;
-		u32 hwirq, intsize, j;
+		u32 hwirq;
+		int i;
 
-		if (mapsize < 3)
-			return -EINVAL;
-		hwirq = be32_to_cpup(map);
-		if (hwirq >= MAXIRQ)
+		hwirq = imap_item.child_imap[0];
+		if (hwirq >= MAXIRQ) {
+			of_node_put(imap_item.parent_args.np);
 			return -EINVAL;
+		}
 		priv->nirq = max(priv->nirq, hwirq + 1);
 
-		ipar = of_find_node_by_phandle(be32_to_cpup(map + 2));
-		map += 3;
-		mapsize -= 3;
-		if (!ipar)
-			return -EINVAL;
-		priv->map[hwirq].fwnode = &ipar->fwnode;
-		ret = of_property_read_u32(ipar, "#interrupt-cells", &intsize);
-		if (ret)
-			return ret;
-
-		if (intsize > mapsize)
-			return -EINVAL;
+		ipar = of_node_get(imap_item.parent_args.np);
+		priv->map[hwirq].fwnode = of_fwnode_handle(ipar);
 
-		priv->map[hwirq].param_count = intsize;
-		for (j = 0; j < intsize; ++j)
-			priv->map[hwirq].param[j] = be32_to_cpup(map++);
-		mapsize -= intsize;
+		priv->map[hwirq].param_count = imap_item.parent_args.args_count;
+		for (i = 0; i < priv->map[hwirq].param_count; i++)
+			priv->map[hwirq].param[i] = imap_item.parent_args.args[i];
 	}
 	return 0;
 }
-- 
2.52.0

[PATCH v8 4/8] irqchip/renesas-rza1: Use for_each_of_imap_item iterator

[Herve Codina (Schneider Electric)]

The renesas-rza1 driver parses the interrupt-map property. It does it
using open code.

Recently for_each_of_imap_item iterator has been introduce to help
drivers in this parsing.

Convert the renesas-rza1 driver to use the for_each_of_imap_item
iterator instead of open code.

Signed-off-by: Herve Codina (Schneider Electric) <herve.codina@bootlin.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
---
 drivers/irqchip/irq-renesas-rza1.c | 43 +++++++++++-------------------
 1 file changed, 16 insertions(+), 27 deletions(-)

diff --git a/drivers/irqchip/irq-renesas-rza1.c b/drivers/irqchip/irq-renesas-rza1.c
index 6047a524ac77..370d968b2398 100644
--- a/drivers/irqchip/irq-renesas-rza1.c
+++ b/drivers/irqchip/irq-renesas-rza1.c
@@ -142,47 +142,36 @@ static const struct irq_domain_ops rza1_irqc_domain_ops = {
 static int rza1_irqc_parse_map(struct rza1_irqc_priv *priv,
 			       struct device_node *gic_node)
 {
+	struct of_imap_parser imap_parser;
 	struct device *dev = priv->dev;
-	unsigned int imaplen, i, j;
+	struct of_imap_item imap_item;
 	struct device_node *ipar;
-	const __be32 *imap;
-	u32 intsize;
+	unsigned int j;
+	u32 i = 0;
 	int ret;
 
-	imap = of_get_property(dev->of_node, "interrupt-map", &imaplen);
-	if (!imap)
-		return -EINVAL;
-
-	for (i = 0; i < IRQC_NUM_IRQ; i++) {
-		if (imaplen < 3)
-			return -EINVAL;
+	ret = of_imap_parser_init(&imap_parser, dev->of_node, &imap_item);
+	if (ret)
+		return ret;
 
+	for_each_of_imap_item(&imap_parser, &imap_item) {
 		/* Check interrupt number, ignore sense */
-		if (be32_to_cpup(imap) != i)
+		if (imap_item.child_imap[0] != i) {
+			of_node_put(imap_item.parent_args.np);
 			return -EINVAL;
+		}
 
-		ipar = of_find_node_by_phandle(be32_to_cpup(imap + 2));
+		ipar  = imap_item.parent_args.np;
 		if (ipar != gic_node) {
 			of_node_put(ipar);
 			return -EINVAL;
 		}
 
-		imap += 3;
-		imaplen -= 3;
-
-		ret = of_property_read_u32(ipar, "#interrupt-cells", &intsize);
-		of_node_put(ipar);
-		if (ret)
-			return ret;
-
-		if (imaplen < intsize)
-			return -EINVAL;
-
-		priv->map[i].args_count = intsize;
-		for (j = 0; j < intsize; j++)
-			priv->map[i].args[j] = be32_to_cpup(imap++);
+		priv->map[i].args_count = imap_item.parent_args.args_count;
+		for (j = 0; j < priv->map[i].args_count; j++)
+			priv->map[i].args[j] = imap_item.parent_args.args[j];
 
-		imaplen -= intsize;
+		i++;
 	}
 
 	return 0;
-- 
2.52.0

[PATCH v8 5/8] ARM: dts: r9a06g032: Add GPIO controllers

[Herve Codina (Schneider Electric)]

Add GPIO controllers (Synopsys DesignWare IPs) available in the
r9a06g032 (RZ/N1D) SoC.

Signed-off-by: Herve Codina (Schneider Electric) <herve.codina@bootlin.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
---
 arch/arm/boot/dts/renesas/r9a06g032.dtsi | 118 +++++++++++++++++++++++
 1 file changed, 118 insertions(+)

diff --git a/arch/arm/boot/dts/renesas/r9a06g032.dtsi b/arch/arm/boot/dts/renesas/r9a06g032.dtsi
index 8debb77803bb..06d35a83f6e1 100644
--- a/arch/arm/boot/dts/renesas/r9a06g032.dtsi
+++ b/arch/arm/boot/dts/renesas/r9a06g032.dtsi
@@ -509,6 +509,124 @@ gic: interrupt-controller@44101000 {
 				<GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
 		};
 
+		/*
+		 * The GPIO mapping to the corresponding pins is not obvious.
+		 * See the hardware documentation for details.
+		 */
+		gpio0: gpio@5000b000 {
+			compatible = "snps,dw-apb-gpio";
+			reg = <0x5000b000 0x80>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&sysctrl R9A06G032_HCLK_GPIO0>;
+			clock-names = "bus";
+
+			/* GPIO0a[0]      connected to pin  GPIO0      */
+			/* GPIO0a[1..2]   connected to pins GPIO3..4   */
+			/* GPIO0a[3..4]   connected to pins GPIO9..10  */
+			/* GPIO0a[5]      connected to pin  GPIO12     */
+			/* GPIO0a[6..7]   connected to pins GPIO15..16 */
+			/* GPIO0a[8..9]   connected to pins GPIO21..22 */
+			/* GPIO0a[10]     connected to pin  GPIO24     */
+			/* GPIO0a[11..12] connected to pins GPIO27..28 */
+			/* GPIO0a[13..14] connected to pins GPIO33..34 */
+			/* GPIO0a[15]     connected to pin  GPIO36     */
+			/* GPIO0a[16..17] connected to pins GPIO39..40 */
+			/* GPIO0a[18..19] connected to pins GPIO45..46 */
+			/* GPIO0a[20]     connected to pin  GPIO48     */
+			/* GPIO0a[21..22] connected to pins GPIO51..52 */
+			/* GPIO0a[23..24] connected to pins GPIO57..58 */
+			/* GPIO0a[25..31] connected to pins GPIO62..68 */
+			gpio0a: gpio-port@0 {
+				compatible = "snps,dw-apb-gpio-port";
+				reg = <0>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				snps,nr-gpios = <32>;
+			};
+
+			/* GPIO0b[0..1]   connected to pins GPIO1..2   */
+			/* GPIO0b[2..5]   connected to pins GPIO5..8   */
+			/* GPIO0b[6]      connected to pin  GPIO11     */
+			/* GPIO0b[7..8]   connected to pins GPIO13..14 */
+			/* GPIO0b[9..12]  connected to pins GPIO17..20 */
+			/* GPIO0b[13]     connected to pin  GPIO23     */
+			/* GPIO0b[14..15] connected to pins GPIO25..26 */
+			/* GPIO0b[16..19] connected to pins GPIO29..32 */
+			/* GPIO0b[20]     connected to pin  GPIO35     */
+			/* GPIO0b[21..22] connected to pins GPIO37..38 */
+			/* GPIO0b[23..26] connected to pins GPIO41..44 */
+			/* GPIO0b[27]     connected to pin  GPIO47     */
+			/* GPIO0b[28..29] connected to pins GPIO49..50 */
+			/* GPIO0b[30..31] connected to pins GPIO53..54 */
+			gpio0b: gpio-port@1 {
+				compatible = "snps,dw-apb-gpio-port";
+				reg = <1>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				snps,nr-gpios = <32>;
+			};
+		};
+
+		gpio1: gpio@5000c000 {
+			compatible = "snps,dw-apb-gpio";
+			reg = <0x5000c000 0x80>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&sysctrl R9A06G032_HCLK_GPIO1>;
+			clock-names = "bus";
+
+			/* GPIO1a[0..4]  connected to pins GPIO69..73 */
+			/* GPIO1a[5..31] connected to pins GPIO95..121 */
+			gpio1a: gpio-port@0 {
+				compatible = "snps,dw-apb-gpio-port";
+				reg = <0>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				snps,nr-gpios = <32>;
+			};
+
+			/* GPIO1b[0..1]   connected to pins GPIO55..56 */
+			/* GPIO1b[2..4]   connected to pins GPIO59..61 */
+			/* GPIO1b[5..25]  connected to pins GPIO74..94 */
+			/* GPIO1b[26..31] connected to pins GPIO150..155 */
+			gpio1b: gpio-port@1 {
+				compatible = "snps,dw-apb-gpio-port";
+				reg = <1>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				snps,nr-gpios = <32>;
+			};
+		};
+
+		gpio2: gpio@5000d000 {
+			compatible = "snps,dw-apb-gpio";
+			reg = <0x5000d000 0x80>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&sysctrl R9A06G032_HCLK_GPIO2>;
+			clock-names = "bus";
+
+			/* GPIO2a[0..27]  connected to pins GPIO122..149 */
+			/* GPIO2a[28..31] connected to pins GPIO156..159 */
+			gpio2a: gpio-port@0 {
+				compatible = "snps,dw-apb-gpio-port";
+				reg = <0>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				snps,nr-gpios = <32>;
+			};
+
+			/* GPIO2b[0..9] connected to pins GPIO160..169 */
+			gpio2b: gpio-port@1 {
+				compatible = "snps,dw-apb-gpio-port";
+				reg = <1>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				snps,nr-gpios = <10>;
+			};
+		};
+
 		can0: can@52104000 {
 			compatible = "renesas,r9a06g032-sja1000", "renesas,rzn1-sja1000";
 			reg = <0x52104000 0x800>;
-- 
2.52.0

[PATCH v8 6/8] dt-bindings: soc: renesas: Add the Renesas RZ/N1 GPIO Interrupt Multiplexer

[Herve Codina (Schneider Electric)]

On the Renesas RZ/N1 SoC, GPIOs can generate interruptions. Those
interruption lines are multiplexed by the GPIO Interrupt Multiplexer in
order to map 32 * 3 GPIO interrupt lines to 8 GIC interrupt lines.

The GPIO interrupt multiplexer IP does nothing but select 8 GPIO
IRQ lines out of the 96 available to wire them to the GIC input lines.

Signed-off-by: Herve Codina (Schneider Electric) <herve.codina@bootlin.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
 .../soc/renesas/renesas,rzn1-gpioirqmux.yaml  | 87 +++++++++++++++++++
 1 file changed, 87 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/soc/renesas/renesas,rzn1-gpioirqmux.yaml

diff --git a/Documentation/devicetree/bindings/soc/renesas/renesas,rzn1-gpioirqmux.yaml b/Documentation/devicetree/bindings/soc/renesas/renesas,rzn1-gpioirqmux.yaml
new file mode 100644
index 000000000000..1a31c11bc3b4
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/renesas/renesas,rzn1-gpioirqmux.yaml
@@ -0,0 +1,87 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/renesas/renesas,rzn1-gpioirqmux.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Renesas RZ/N1 SoCs GPIO Interrupt Multiplexer
+
+description: |
+   The Renesas RZ/N1 GPIO Interrupt Multiplexer multiplexes GPIO interrupt
+   lines to the interrupt controller available in the SoC.
+
+   It selects up to 8 of the 96 GPIO interrupt lines available and connect them
+   to 8 output interrupt lines.
+
+maintainers:
+  - Herve Codina <herve.codina@bootlin.com>
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - renesas,r9a06g032-gpioirqmux
+      - const: renesas,rzn1-gpioirqmux
+
+  reg:
+    maxItems: 1
+
+  "#address-cells":
+    const: 0
+
+  "#interrupt-cells":
+    const: 1
+
+  interrupt-map-mask:
+    items:
+      - const: 0x7f
+
+  interrupt-map:
+    description: |
+      Specifies the mapping from external GPIO interrupt lines to the output
+      interrupts. The array has up to 8 items defining the mapping related to
+      the output line 0 (GIC 103) up to the output line 7 (GIC 110).
+
+      The child interrupt number set in arrays items is computed using the
+      following formula:
+          gpio_bank * 32 + gpio_number
+      with:
+        - gpio_bank: The GPIO bank number
+            - 0 for GPIO0A,
+            - 1 for GPIO1A,
+            - 2 for GPIO2A
+        - gpio_number: Number of the gpio in the bank (0..31)
+    minItems: 1
+    maxItems: 8
+
+required:
+  - compatible
+  - reg
+  - "#address-cells"
+  - "#interrupt-cells"
+  - interrupt-map-mask
+  - interrupt-map
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    gic: interrupt-controller {
+        interrupt-controller;
+        #address-cells = <0>;
+        #interrupt-cells = <3>;
+    };
+
+    interrupt-controller@51000480 {
+        compatible = "renesas,r9a06g032-gpioirqmux", "renesas,rzn1-gpioirqmux";
+        reg = <0x51000480 0x20>;
+        #address-cells = <0>;
+        #interrupt-cells = <1>;
+        interrupt-map-mask = <0x7f>;
+        interrupt-map =
+            <32 &gic GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>, /* line 0, GPIO1A.0 */
+            <89 &gic GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>, /* line 1, GPIO2A.25 */
+            <9 &gic GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>; /* line 3, GPIO0A.9 */
+    };
-- 
2.52.0

[PATCH v8 7/8] soc: renesas: Add support for Renesas RZ/N1 GPIO Interrupt Multiplexer

[Herve Codina (Schneider Electric)]

On the Renesas RZ/N1 SoC, GPIOs can generate interruptions. Those
interruption lines are multiplexed by the GPIO Interrupt Multiplexer in
order to map 32 * 3 GPIO interrupt lines to 8 GIC interrupt lines.

The GPIO interrupt multiplexer IP does nothing but select 8 GPIO
IRQ lines out of the 96 available to wire them to the GIC input lines.

Signed-off-by: Herve Codina (Schneider Electric) <herve.codina@bootlin.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
 drivers/soc/renesas/Kconfig       |   4 +
 drivers/soc/renesas/Makefile      |   1 +
 drivers/soc/renesas/rzn1_irqmux.c | 127 ++++++++++++++++++++++++++++++
 3 files changed, 132 insertions(+)
 create mode 100644 drivers/soc/renesas/rzn1_irqmux.c

diff --git a/drivers/soc/renesas/Kconfig b/drivers/soc/renesas/Kconfig
index 340a1ff7e92b..2dc51873480a 100644
--- a/drivers/soc/renesas/Kconfig
+++ b/drivers/soc/renesas/Kconfig
@@ -62,6 +62,7 @@ config ARCH_RZN1
 	select PM
 	select PM_GENERIC_DOMAINS
 	select ARM_AMBA
+	select RZN1_IRQMUX if GPIO_DWAPB
 
 if ARM && ARCH_RENESAS
 
@@ -459,6 +460,9 @@ config PWC_RZV2M
 config RST_RCAR
 	bool "Reset Controller support for R-Car" if COMPILE_TEST
 
+config RZN1_IRQMUX
+	bool "Renesas RZ/N1 GPIO IRQ multiplexer support" if COMPILE_TEST
+
 config SYSC_RZ
 	bool "System controller for RZ SoCs" if COMPILE_TEST
 	select MFD_SYSCON
diff --git a/drivers/soc/renesas/Makefile b/drivers/soc/renesas/Makefile
index 3bdcc6a395d5..33d44d964d61 100644
--- a/drivers/soc/renesas/Makefile
+++ b/drivers/soc/renesas/Makefile
@@ -14,4 +14,5 @@ obj-$(CONFIG_SYS_R9A09G057)	+= r9a09g057-sys.o
 # Family
 obj-$(CONFIG_PWC_RZV2M)		+= pwc-rzv2m.o
 obj-$(CONFIG_RST_RCAR)		+= rcar-rst.o
+obj-$(CONFIG_RZN1_IRQMUX)	+= rzn1_irqmux.o
 obj-$(CONFIG_SYSC_RZ)		+= rz-sysc.o
diff --git a/drivers/soc/renesas/rzn1_irqmux.c b/drivers/soc/renesas/rzn1_irqmux.c
new file mode 100644
index 000000000000..b50b295f83d7
--- /dev/null
+++ b/drivers/soc/renesas/rzn1_irqmux.c
@@ -0,0 +1,127 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * RZ/N1 GPIO Interrupt Multiplexer
+ *
+ * Copyright 2025 Schneider Electric
+ * Author: Herve Codina <herve.codina@bootlin.com>
+ */
+
+#include <linux/bitmap.h>
+#include <linux/bitops.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/platform_device.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/*
+ * Up to 8 output lines are connected to GIC SPI interrupt controller
+ * starting at IRQ 103.
+ */
+#define RZN1_IRQMUX_GIC_SPI_BASE	103
+#define RZN1_IRQMUX_NUM_OUTPUTS		8
+
+static int rzn1_irqmux_parent_args_to_line_index(struct device *dev,
+						 const struct of_phandle_args *parent_args)
+{
+	/*
+	 * The parent interrupt should be one of the GIC controller.
+	 * Three arguments must be provided.
+	 *  - args[0]: GIC_SPI
+	 *  - args[1]: The GIC interrupt number
+	 *  - args[2]: The interrupt flags
+	 *
+	 * We retrieve the line index based on the GIC interrupt number
+	 * provided.
+	 */
+
+	if (parent_args->args_count != 3 || parent_args->args[0] != GIC_SPI) {
+		dev_err(dev, "Invalid interrupt-map item\n");
+		return -EINVAL;
+	}
+
+	if (parent_args->args[1] < RZN1_IRQMUX_GIC_SPI_BASE ||
+	    parent_args->args[1] >= RZN1_IRQMUX_GIC_SPI_BASE + RZN1_IRQMUX_NUM_OUTPUTS) {
+		dev_err(dev, "Invalid GIC interrupt %u\n", parent_args->args[1]);
+		return -EINVAL;
+	}
+
+	return parent_args->args[1] - RZN1_IRQMUX_GIC_SPI_BASE;
+}
+
+static int rzn1_irqmux_probe(struct platform_device *pdev)
+{
+	DECLARE_BITMAP(index_done, RZN1_IRQMUX_NUM_OUTPUTS) = {};
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct of_imap_parser imap_parser;
+	struct of_imap_item imap_item;
+	u32 __iomem *regs;
+	int index;
+	int ret;
+	u32 tmp;
+
+	regs = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(regs))
+		return PTR_ERR(regs);
+
+	/* We support only #interrupt-cells = <1> and #address-cells = <0> */
+	ret = of_property_read_u32(np, "#interrupt-cells", &tmp);
+	if (ret)
+		return ret;
+	if (tmp != 1)
+		return -EINVAL;
+
+	ret = of_property_read_u32(np, "#address-cells", &tmp);
+	if (ret)
+		return ret;
+	if (tmp != 0)
+		return -EINVAL;
+
+	ret = of_imap_parser_init(&imap_parser, np, &imap_item);
+	if (ret)
+		return ret;
+
+	for_each_of_imap_item(&imap_parser, &imap_item) {
+		index = rzn1_irqmux_parent_args_to_line_index(dev, &imap_item.parent_args);
+		if (index < 0) {
+			of_node_put(imap_item.parent_args.np);
+			return index;
+		}
+
+		if (test_and_set_bit(index, index_done)) {
+			of_node_put(imap_item.parent_args.np);
+			dev_err(dev, "Mux output line %d already defined in interrupt-map\n",
+				index);
+			return -EINVAL;
+		}
+
+		/*
+		 * The child #address-cells is 0 (already checked). The first
+		 * value in imap item is the src hwirq.
+		 */
+		writel(imap_item.child_imap[0], regs + index);
+	}
+
+	return 0;
+}
+
+static const struct of_device_id rzn1_irqmux_of_match[] = {
+	{ .compatible = "renesas,rzn1-gpioirqmux", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, rzn1_irqmux_of_match);
+
+static struct platform_driver rzn1_irqmux_driver = {
+	.probe = rzn1_irqmux_probe,
+	.driver = {
+		.name = "rzn1_irqmux",
+		.of_match_table = rzn1_irqmux_of_match,
+	},
+};
+module_platform_driver(rzn1_irqmux_driver);
+
+MODULE_AUTHOR("Herve Codina <herve.codina@bootlin.com>");
+MODULE_DESCRIPTION("Renesas RZ/N1 GPIO IRQ Multiplexer Driver");
+MODULE_LICENSE("GPL");
-- 
2.52.0

[PATCH v8 8/8] ARM: dts: r9a06g032: Add support for GPIO interrupts

[Herve Codina (Schneider Electric)]

In the RZ/N1 SoC, the GPIO interrupts are multiplexed using the GPIO
Interrupt Multiplexer.

Add the multiplexer node and connect GPIO interrupt lines to the
multiplexer.

The interrupt-map available in the multiplexer node has to be updated in
dts files depending on the GPIO usage. Indeed, the usage of an interrupt
for a GPIO is board dependent.

Up to 8 GPIOs can be used as an interrupt line (one per multiplexer
output interrupt).

Signed-off-by: Herve Codina (Schneider Electric) <herve.codina@bootlin.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
---
 arch/arm/boot/dts/renesas/r9a06g032.dtsi | 41 ++++++++++++++++++++++++
 1 file changed, 41 insertions(+)

diff --git a/arch/arm/boot/dts/renesas/r9a06g032.dtsi b/arch/arm/boot/dts/renesas/r9a06g032.dtsi
index 06d35a83f6e1..b8e03c529007 100644
--- a/arch/arm/boot/dts/renesas/r9a06g032.dtsi
+++ b/arch/arm/boot/dts/renesas/r9a06g032.dtsi
@@ -543,6 +543,14 @@ gpio0a: gpio-port@0 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				snps,nr-gpios = <32>;
+
+				interrupt-controller;
+				interrupt-parent = <&gpioirqmux>;
+				interrupts = <0  1  2  3  4  5  6  7
+					      8  9 10 11 12 13 14 15
+					     16 17 18 19 20 21 22 23
+					     24 25 26 27 28 29 30 31>;
+				#interrupt-cells = <2>;
 			};
 
 			/* GPIO0b[0..1]   connected to pins GPIO1..2   */
@@ -584,6 +592,14 @@ gpio1a: gpio-port@0 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				snps,nr-gpios = <32>;
+
+				interrupt-controller;
+				interrupt-parent = <&gpioirqmux>;
+				interrupts = <32 33 34 35 36 37 38 39
+					      40 41 42 43 44 45 46 47
+					      48 49 50 51 52 53 54 55
+					      56 57 58 59 60 61 62 63>;
+				#interrupt-cells = <2>;
 			};
 
 			/* GPIO1b[0..1]   connected to pins GPIO55..56 */
@@ -615,6 +631,14 @@ gpio2a: gpio-port@0 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				snps,nr-gpios = <32>;
+
+				interrupt-controller;
+				interrupt-parent = <&gpioirqmux>;
+				interrupts = <64 65 66 67 68 69 70 71
+					      72 73 74 75 76 77 78 79
+					      80 81 82 83 84 85 86 87
+					      88 89 90 91 92 93 94 95>;
+				#interrupt-cells = <2>;
 			};
 
 			/* GPIO2b[0..9] connected to pins GPIO160..169 */
@@ -627,6 +651,23 @@ gpio2b: gpio-port@1 {
 			};
 		};
 
+		gpioirqmux: interrupt-controller@51000480 {
+			compatible = "renesas,r9a06g032-gpioirqmux", "renesas,rzn1-gpioirqmux";
+			reg = <0x51000480 0x20>;
+			#interrupt-cells = <1>;
+			#address-cells = <0>;
+			interrupt-map-mask = <0x7f>;
+
+			/*
+			 * Example mapping entry. Board DTs need to overwrite
+			 * 'interrupt-map' with their specific mapping. Check
+			 * the irqmux binding documentation for details.
+			 */
+			interrupt-map = <0 &gic GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+
+			status = "disabled";
+		};
+
 		can0: can@52104000 {
 			compatible = "renesas,r9a06g032-sja1000", "renesas,rzn1-sja1000";
 			reg = <0x52104000 0x800>;
-- 
2.52.0

Re: [PATCH v8 0/8] gpio: renesas: Add support for GPIO and related interrupts in RZ/N1 SoC

[Wolfram Sang]

[-- Attachment #1: Type: text/plain, Size: 269 bytes --]


> Rob, Thomas, this series is blocked waiting for your feedback and your
> acks if you are okay.

This was a little hidden between the other text, so let me emphasize
that these acks are needed. The other option is to send the irq stuff
and the SoC stuff seperately.


[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

Re: [PATCH v8 5/8] ARM: dts: r9a06g032: Add GPIO controllers

[Geert Uytterhoeven]

On Wed, 14 Jan 2026 at 10:40, Herve Codina (Schneider Electric)
<herve.codina@bootlin.com> wrote:
> Add GPIO controllers (Synopsys DesignWare IPs) available in the
> r9a06g032 (RZ/N1D) SoC.
>
> Signed-off-by: Herve Codina (Schneider Electric) <herve.codina@bootlin.com>
> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
> Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
> Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

Thanks, will queue in renesas-devel for v6.20.

Gr{oetje,eeting}s,

                        Geert

-- 
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

Re: [PATCH v8 8/8] ARM: dts: r9a06g032: Add support for GPIO interrupts

[Geert Uytterhoeven]

On Wed, 14 Jan 2026 at 10:41, Herve Codina (Schneider Electric)
<herve.codina@bootlin.com> wrote:
> In the RZ/N1 SoC, the GPIO interrupts are multiplexed using the GPIO
> Interrupt Multiplexer.
>
> Add the multiplexer node and connect GPIO interrupt lines to the
> multiplexer.
>
> The interrupt-map available in the multiplexer node has to be updated in
> dts files depending on the GPIO usage. Indeed, the usage of an interrupt
> for a GPIO is board dependent.
>
> Up to 8 GPIOs can be used as an interrupt line (one per multiplexer
> output interrupt).
>
> Signed-off-by: Herve Codina (Schneider Electric) <herve.codina@bootlin.com>
> Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
> Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
i.e. will queue in renesas-devel for v6.20.

Gr{oetje,eeting}s,

                        Geert

-- 
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

Re: [PATCH v8 0/8] gpio: renesas: Add support for GPIO and related interrupts in RZ/N1 SoC

[Geert Uytterhoeven]

On Wed, 14 Jan 2026 at 11:03, Wolfram Sang
<wsa+renesas@sang-engineering.com> wrote:
> > Rob, Thomas, this series is blocked waiting for your feedback and your
> > acks if you are okay.
>
> This was a little hidden between the other text, so let me emphasize
> that these acks are needed. The other option is to send the irq stuff
> and the SoC stuff seperately.

The irq and SoC stuff depend on the of stuff, so doing so would
delay the former by one cycle.

On IRC, Rob sort of agreed to option A from my proposal (see v7 cover
letter):

  A. Rob takes the first two patches, and provides an immutable branch.
     Then Thomas takes the irqchip patches, and I take the rest.

Unfortunately that part hasn't happened yet...

Meanwhile, I'm queuing the DTS patches for v6.20 anyway, as they
have no dependencies.

Gr{oetje,eeting}s,

                        Geert


--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

Re: [PATCH v8 0/8] gpio: renesas: Add support for GPIO and related interrupts in RZ/N1 SoC

[Wolfram Sang]

[-- Attachment #1: Type: text/plain, Size: 507 bytes --]


> The irq and SoC stuff depend on the of stuff, so doing so would
> delay the former by one cycle.

I know, but it is still better than nothing happening ;)

> On IRC, Rob sort of agreed to option A from my proposal (see v7 cover
> letter):

Cool, didn't know this.

> Unfortunately that part hasn't happened yet...

IRC to the rescue again? I'd think it will be easier for Thomas if he
gets a PR from Rob. Maybe Rob should take the first 4 patches even, then
Thomas only needs to review the PR.

Thanks!


[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

Re: [PATCH v8 3/8] irqchip/ls-extirq: Use for_each_of_imap_item iterator

[Thomas Gleixner]

On Wed, Jan 14 2026 at 10:39, Herve Codina wrote:
> The ls-extirq driver parses the interrupt-map property. It does it using
> open code.
>
> Recently for_each_of_imap_item iterator has been introduce to help
> drivers in this parsing.
>
> Convert the ls-extirq driver to use the for_each_of_imap_item
> iterator instead of open code.
>
> Signed-off-by: Herve Codina (Schneider Electric) <herve.codina@bootlin.com>
> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

Reviewed-by: Thomas Gleixner <tglx@kernel.org>

Re: [PATCH v8 4/8] irqchip/renesas-rza1: Use for_each_of_imap_item iterator

[Thomas Gleixner]

On Wed, Jan 14 2026 at 10:39, Herve Codina wrote:
> The renesas-rza1 driver parses the interrupt-map property. It does it
> using open code.
>
> Recently for_each_of_imap_item iterator has been introduce to help
> drivers in this parsing.
>
> Convert the renesas-rza1 driver to use the for_each_of_imap_item
> iterator instead of open code.
>
> Signed-off-by: Herve Codina (Schneider Electric) <herve.codina@bootlin.com>
> Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

Reviewed-by: Thomas Gleixner <tglx@kernel.org>

Re: [PATCH v8 0/8] gpio: renesas: Add support for GPIO and related interrupts in RZ/N1 SoC

[Rob Herring]

On Wed, Jan 14, 2026 at 4:47 AM Geert Uytterhoeven <geert@linux-m68k.org> wrote:
>
> On Wed, 14 Jan 2026 at 11:03, Wolfram Sang
> <wsa+renesas@sang-engineering.com> wrote:
> > > Rob, Thomas, this series is blocked waiting for your feedback and your
> > > acks if you are okay.
> >
> > This was a little hidden between the other text, so let me emphasize
> > that these acks are needed. The other option is to send the irq stuff
> > and the SoC stuff seperately.

Reviewed-by > Acked-by

And if it has either, I stop paying attention. So I was assuming this
all was going in via not-my-tree...

> The irq and SoC stuff depend on the of stuff, so doing so would
> delay the former by one cycle.
>
> On IRC, Rob sort of agreed to option A from my proposal (see v7 cover
> letter):
>
>   A. Rob takes the first two patches, and provides an immutable branch.
>      Then Thomas takes the irqchip patches, and I take the rest.

Until this...

> Unfortunately that part hasn't happened yet...

And then a new version came in... Why a new version only to add a
Tested-by tag? That sends you to the back of the queue in my normal
workflow (which this is turning into anything but).

Thomas has now provided a Reviewed-by. I think it is easiest if you
just take the whole series via Renesas tree.

Rob

Re: [PATCH v8 0/8] gpio: renesas: Add support for GPIO and related interrupts in RZ/N1 SoC

[Geert Uytterhoeven]

On Wed, 14 Jan 2026 at 23:21, Rob Herring <robh@kernel.org> wrote:
> On Wed, Jan 14, 2026 at 4:47 AM Geert Uytterhoeven <geert@linux-m68k.org> wrote:
> > On Wed, 14 Jan 2026 at 11:03, Wolfram Sang
> > <wsa+renesas@sang-engineering.com> wrote:
> > > > Rob, Thomas, this series is blocked waiting for your feedback and your
> > > > acks if you are okay.
> > >
> > > This was a little hidden between the other text, so let me emphasize
> > > that these acks are needed. The other option is to send the irq stuff
> > > and the SoC stuff seperately.
>
> Reviewed-by > Acked-by

It does have different semantics...

> And if it has either, I stop paying attention. So I was assuming this
> all was going in via not-my-tree...
>
> > The irq and SoC stuff depend on the of stuff, so doing so would
> > delay the former by one cycle.
> >
> > On IRC, Rob sort of agreed to option A from my proposal (see v7 cover
> > letter):
> >
> >   A. Rob takes the first two patches, and provides an immutable branch.
> >      Then Thomas takes the irqchip patches, and I take the rest.
>
> Until this...
>
> > Unfortunately that part hasn't happened yet...
>
> And then a new version came in... Why a new version only to add a
> Tested-by tag? That sends you to the back of the queue in my normal
> workflow (which this is turning into anything but).
>
> Thomas has now provided a Reviewed-by. I think it is easiest if you
> just take the whole series via Renesas tree.

OK doing so...
Thanks!

Gr{oetje,eeting}s,

                        Geert

-- 
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

Re: [PATCH v8 3/8] irqchip/ls-extirq: Use for_each_of_imap_item iterator

[Ioana Ciornei]

On Wed, Jan 14, 2026 at 10:39:32AM +0100, Herve Codina (Schneider Electric) wrote:
> The ls-extirq driver parses the interrupt-map property. It does it using
> open code.
> 
> Recently for_each_of_imap_item iterator has been introduce to help
> drivers in this parsing.
> 
> Convert the ls-extirq driver to use the for_each_of_imap_item
> iterator instead of open code.
> 

The ls-extirq uses interrupt-map but it's a non-standard use documented
in fsl,ls-extirq.yaml:

	# The driver(drivers/irqchip/irq-ls-extirq.c) have not use standard DT
	# function to parser interrupt-map. So it doesn't consider '#address-size'
	# in parent interrupt controller, such as GIC.
	#
	# When dt-binding verify interrupt-map, item data matrix is spitted at
	# incorrect position. Remove interrupt-map restriction because it always
	# wrong.

This means that by using for_each_of_imap_item and the underlying
of_irq_parse_imap_parent() on its interrupt-map property will
effectively break its functionality.

Unfortunatelly, I am not sure how this can be fixed other than with a
revert.

Ioana

Re: [PATCH v8 3/8] irqchip/ls-extirq: Use for_each_of_imap_item iterator

[Herve Codina]

Hi Ioana,

On Wed, 11 Feb 2026 12:03:00 +0200
Ioana Ciornei <ioana.ciornei@nxp.com> wrote:

> On Wed, Jan 14, 2026 at 10:39:32AM +0100, Herve Codina (Schneider Electric) wrote:
> > The ls-extirq driver parses the interrupt-map property. It does it using
> > open code.
> > 
> > Recently for_each_of_imap_item iterator has been introduce to help
> > drivers in this parsing.
> > 
> > Convert the ls-extirq driver to use the for_each_of_imap_item
> > iterator instead of open code.
> >   
> 
> The ls-extirq uses interrupt-map but it's a non-standard use documented
> in fsl,ls-extirq.yaml:
> 
> 	# The driver(drivers/irqchip/irq-ls-extirq.c) have not use standard DT
> 	# function to parser interrupt-map. So it doesn't consider '#address-size'
> 	# in parent interrupt controller, such as GIC.
> 	#
> 	# When dt-binding verify interrupt-map, item data matrix is spitted at
> 	# incorrect position. Remove interrupt-map restriction because it always
> 	# wrong.
> 
> This means that by using for_each_of_imap_item and the underlying
> of_irq_parse_imap_parent() on its interrupt-map property will
> effectively break its functionality.
> 
> Unfortunatelly, I am not sure how this can be fixed other than with a
> revert.
> 

Well, if this is the only solution due to non compliance with interrupt-map,
I am not opposed to the revert of the following patch:
  3ac6dfe3d7a23 ("irqchip/ls-extirq: Use for_each_of_imap_item iterator")

(SHA taken from next-20260205 tag)

Best regards,
Hervé