[PATCH v3 0/5] Add Dell Inspiron 7441 / Latitude 7455 (X1E-80-100)

[PATCH v3 0/5] Add Dell Inspiron 7441 / Latitude 7455 (X1E-80-100)

[Val Packett]

The unified series for Dell Thena laptops.

Changes since v2[1]:

- Fixed From/Co-developed-by on the big patch
- Fixed one remaining "inspirIon"
- Fixed codec/cpu alphabetical order in audio nodes (copy-paste..)
- Made the common dtsi an 'x1-' one in preparation for x1p models

[1]: https://lore.kernel.org/all/20250701231643.568854-1-val@packett.cool/

Bryan O'Donoghue (2):
  dt-bindings: arm: qcom: Add Dell Inspiron 14 Plus 7441
  arm64: dts: qcom: Add support for Dell Inspiron 7441 / Latitude 7455

Val Packett (3):
  dt-bindings: arm: qcom: Add Dell Latitude 7455
  firmware: qcom: scm: Allow QSEECOM on Dell Inspiron 7441 / Latitude
    7455
  drm/panel-edp: Add BOE NE14QDM panel for Dell Latitude 7455

 .../devicetree/bindings/arm/qcom.yaml         |    2 +
 arch/arm64/boot/dts/qcom/Makefile             |    4 +
 arch/arm64/boot/dts/qcom/x1-dell-thena.dtsi   | 1657 +++++++++++++++++
 .../x1e80100-dell-inspiron-14-plus-7441.dts   |   52 +
 .../dts/qcom/x1e80100-dell-latitude-7455.dts  |   53 +
 drivers/firmware/qcom/qcom_scm.c              |    2 +
 drivers/gpu/drm/panel/panel-edp.c             |    1 +
 7 files changed, 1771 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/x1-dell-thena.dtsi
 create mode 100644 arch/arm64/boot/dts/qcom/x1e80100-dell-inspiron-14-plus-7441.dts
 create mode 100644 arch/arm64/boot/dts/qcom/x1e80100-dell-latitude-7455.dts

-- 
2.49.0

[PATCH v3 1/5] dt-bindings: arm: qcom: Add Dell Inspiron 14 Plus 7441

[Val Packett]

From: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

Document the X1E80100-based Dell Inspiron 14 Plus 7441 laptop, codename:
Thena.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Val Packett <val@packett.cool>
---
 Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index ae43b3556580..8e3b804864fa 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -1146,6 +1146,7 @@ properties:
           - enum:
               - asus,vivobook-s15
               - asus,zenbook-a14-ux3407ra
+              - dell,inspiron-14-plus-7441
               - dell,xps13-9345
               - hp,elitebook-ultra-g1q
               - hp,omnibook-x14
-- 
2.49.0

[PATCH v3 2/5] dt-bindings: arm: qcom: Add Dell Latitude 7455

[Val Packett]

Document the X1E80100-based Dell Latitude 7455 laptop, codename Thena
(the codename is shared with the near-identical Inspiron 14 Plus 7441).

Signed-off-by: Val Packett <val@packett.cool>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 8e3b804864fa..162f80123cf6 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -1147,6 +1147,7 @@ properties:
               - asus,vivobook-s15
               - asus,zenbook-a14-ux3407ra
               - dell,inspiron-14-plus-7441
+              - dell,latitude-7455
               - dell,xps13-9345
               - hp,elitebook-ultra-g1q
               - hp,omnibook-x14
-- 
2.49.0

[PATCH v3 3/5] arm64: dts: qcom: Add support for Dell Inspiron 7441 / Latitude 7455

[Val Packett]

From: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

Add device trees for both SKUs of the X1E80100 Thena laptop:
- Dell Latitude 7455
- Dell Inspiron 14 Plus 7441

Works:
- Wi-Fi (WCN7850 hw2.0)
- Bluetooth
- USB Type-C x2 (with DP alt mode)
- USB Type-A
- USB Fingerprint reader
- eDP Display (with brightness)
- NVMe
- SDHC (microSD slot)
- Keyboard
- Touchpad
- Touchscreen
- Audio (4 Speakers, 2 DMICs, Combo Jack)
- Battery

Not included:
- Camera

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Co-developed-by: Val Packett <val@packett.cool>
Signed-off-by: Val Packett <val@packett.cool>
---
 arch/arm64/boot/dts/qcom/Makefile             |    4 +
 arch/arm64/boot/dts/qcom/x1-dell-thena.dtsi   | 1657 +++++++++++++++++
 .../x1e80100-dell-inspiron-14-plus-7441.dts   |   52 +
 .../dts/qcom/x1e80100-dell-latitude-7455.dts  |   53 +
 4 files changed, 1766 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/x1-dell-thena.dtsi
 create mode 100644 arch/arm64/boot/dts/qcom/x1e80100-dell-inspiron-14-plus-7441.dts
 create mode 100644 arch/arm64/boot/dts/qcom/x1e80100-dell-latitude-7455.dts

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 4bfa926b6a08..d2f932dfcc75 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -315,6 +315,10 @@ x1e80100-asus-zenbook-a14-el2-dtbs	:= x1e80100-asus-zenbook-a14.dtb x1-el2.dtbo
 dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-asus-zenbook-a14.dtb x1e80100-asus-zenbook-a14-el2.dtb
 x1e80100-crd-el2-dtbs	:= x1e80100-crd.dtb x1-el2.dtbo
 dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-crd.dtb x1e80100-crd-el2.dtb
+x1e80100-dell-inspiron-14-plus-7441-el2-dtbs	:= x1e80100-dell-inspiron-14-plus-7441.dtb x1-el2.dtbo
+dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-dell-inspiron-14-plus-7441.dtb x1e80100-dell-inspiron-14-plus-7441-el2.dtb
+x1e80100-dell-latitude-7455-el2-dtbs	:= x1e80100-dell-latitude-7455.dtb x1-el2.dtbo
+dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-dell-latitude-7455.dtb x1e80100-dell-latitude-7455-el2.dtb
 x1e80100-dell-xps13-9345-el2-dtbs	:= x1e80100-dell-xps13-9345.dtb x1-el2.dtbo
 dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-dell-xps13-9345.dtb x1e80100-dell-xps13-9345-el2.dtb
 x1e80100-hp-elitebook-ultra-g1q-el2-dtbs := x1e80100-hp-elitebook-ultra-g1q.dtb x1-el2.dtbo
diff --git a/arch/arm64/boot/dts/qcom/x1-dell-thena.dtsi b/arch/arm64/boot/dts/qcom/x1-dell-thena.dtsi
new file mode 100644
index 000000000000..e9b420ef9a48
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/x1-dell-thena.dtsi
@@ -0,0 +1,1657 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
+ * Copyright (c) 2024 Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
+ * Copyright (c) 2025 Bryan O'Donoghue <bryan.odonoghue@linaro.org>
+ * Copyright (c) 2025 Val Packett <val@packett.cool>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+#include "x1e80100-pmics.dtsi"
+
+/ {
+	chassis-type = "laptop";
+
+	aliases {
+		serial0 = &uart14;
+	};
+
+	wcd938x: audio-codec {
+		compatible = "qcom,wcd9385-codec";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wcd_default>;
+
+		qcom,micbias1-microvolt = <1800000>;
+		qcom,micbias2-microvolt = <1800000>;
+		qcom,micbias3-microvolt = <1800000>;
+		qcom,micbias4-microvolt = <1800000>;
+		qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
+		qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
+		qcom,mbhc-headphone-vthreshold-microvolt = <40000>;
+		qcom,rx-device = <&wcd_rx>;
+		qcom,tx-device = <&wcd_tx>;
+
+		reset-gpios = <&tlmm 191 GPIO_ACTIVE_LOW>;
+
+		vdd-buck-supply = <&vreg_l15b_1p8>;
+		vdd-rxtx-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l15b_1p8>;
+		vdd-mic-bias-supply = <&vreg_bob1>;
+
+		#sound-dai-cells = <1>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&hall_int_n_default>;
+		pinctrl-names = "default";
+
+		switch-lid {
+			gpios = <&tlmm 92 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			wakeup-source;
+			wakeup-event-action = <EV_ACT_DEASSERTED>;
+		};
+	};
+
+	pmic-glink {
+		compatible = "qcom,x1e80100-pmic-glink",
+			     "qcom,sm8550-pmic-glink",
+			     "qcom,pmic-glink";
+		orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>,
+				    <&tlmm 123 GPIO_ACTIVE_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Display-adjacent port */
+		connector@0 {
+			compatible = "usb-c-connector";
+			reg = <0>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_ss0_hs_in: endpoint {
+						remote-endpoint = <&usb_1_ss0_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss0_ss_in: endpoint {
+						remote-endpoint = <&retimer_ss0_ss_out>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					pmic_glink_ss0_con_sbu_in: endpoint {
+						remote-endpoint = <&retimer_ss0_con_sbu_out>;
+					};
+				};
+			};
+		};
+
+		/* User-adjacent port */
+		connector@1 {
+			compatible = "usb-c-connector";
+			reg = <1>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_ss1_hs_in: endpoint {
+						remote-endpoint = <&usb_1_ss1_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss1_ss_in: endpoint {
+						remote-endpoint = <&retimer_ss1_ss_out>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					pmic_glink_ss1_con_sbu_in: endpoint {
+						remote-endpoint = <&retimer_ss1_con_sbu_out>;
+					};
+				};
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		pinctrl-0 = <&cam_indicator_en>;
+		pinctrl-names = "default";
+
+		led-camera-indicator {
+			label = "white:camera-indicator";
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_WHITE>;
+			gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "none";
+			default-state = "off";
+			/* Reuse as a panic indicator until we get a "camera on" trigger */
+			panic-indicator;
+		};
+	};
+
+	reserved-memory {
+		linux,cma {
+			compatible = "shared-dma-pool";
+			size = <0x0 0x8000000>;
+			reusable;
+			linux,cma-default;
+		};
+	};
+
+	sound: sound {
+		compatible = "qcom,x1e80100-sndcard";
+		audio-routing = "WooferLeft IN", "WSA WSA_SPK1 OUT",
+				"TweeterLeft IN", "WSA WSA_SPK2 OUT",
+				"WooferRight IN", "WSA2 WSA_SPK1 OUT",
+				"TweeterRight IN", "WSA2 WSA_SPK2 OUT",
+				"IN1_HPHL", "HPHL_OUT",
+				"IN2_HPHR", "HPHR_OUT",
+				"AMIC2", "MIC BIAS2",
+				"VA DMIC0", "MIC BIAS1",
+				"VA DMIC1", "MIC BIAS1",
+				"VA DMIC0", "VA MIC BIAS1",
+				"VA DMIC1", "VA MIC BIAS1",
+				"TX SWR_INPUT1", "ADC2_OUTPUT";
+
+		wcd-playback-dai-link {
+			link-name = "WCD Playback";
+
+			codec {
+				sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		wcd-capture-dai-link {
+			link-name = "WCD Capture";
+
+			codec {
+				sound-dai = <&wcd938x 1>, <&swr2 1>, <&lpass_txmacro 0>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		wsa-dai-link {
+			link-name = "WSA Playback";
+
+			codec {
+				sound-dai = <&left_woofer>, <&left_tweeter>,
+					    <&swr0 0>, <&lpass_wsamacro 0>,
+					    <&right_woofer>, <&right_tweeter>,
+					    <&swr3 0>, <&lpass_wsa2macro 0>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		va-dai-link {
+			link-name = "VA Capture";
+
+			codec {
+				sound-dai = <&lpass_vamacro 0>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+	};
+
+	vreg_cam_1p8: regulator-cam-1p8 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_CAM_1P8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&tlmm 91 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&cam_ldo_en>;
+		pinctrl-names = "default";
+	};
+
+	vreg_edp_3p3: regulator-edp-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_EDP_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 70 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&edp_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_nvme: regulator-nvme {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_NVME_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 18 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&nvme_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr0_1p15: regulator-rtmr0-1p15 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR0_1P15";
+		regulator-min-microvolt = <1150000>;
+		regulator-max-microvolt = <1150000>;
+
+		gpio = <&pmc8380_5_gpios 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&usb0_pwr_1p15_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr0_1p8: regulator-rtmr0-1p8 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR0_1P8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&pm8550ve_9_gpios 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&usb0_1p8_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr0_3p3: regulator-rtmr0-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR0_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&pm8550_gpios 11 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&usb0_3p3_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr1_1p15: regulator-rtmr1-1p15 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR1_1P15";
+		regulator-min-microvolt = <1150000>;
+		regulator-max-microvolt = <1150000>;
+
+		gpio = <&tlmm 188 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&usb1_pwr_1p15_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr1_1p8: regulator-rtmr1-1p8 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR1_1P8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&tlmm 175 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&usb1_pwr_1p8_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr1_3p3: regulator-rtmr1-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR1_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 186 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&usb1_pwr_3p3_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vph_pwr: regulator-vph-pwr {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vreg_wcn_3p3: regulator-wcn-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_WCN_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 214 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&wcn_sw_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_wcn_0p95: regulator-wcn-0p95 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_WCN_0P95";
+		regulator-min-microvolt = <950000>;
+		regulator-max-microvolt = <950000>;
+
+		vin-supply = <&vreg_wcn_3p3>;
+	};
+
+	vreg_wcn_1p9: regulator-wcn-1p9 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_WCN_1P9";
+		regulator-min-microvolt = <1900000>;
+		regulator-max-microvolt = <1900000>;
+
+		vin-supply = <&vreg_wcn_3p3>;
+	};
+
+	wcn7850-pmu {
+		compatible = "qcom,wcn7850-pmu";
+
+		vdd-supply = <&vreg_wcn_0p95>;
+		vddio-supply = <&vreg_l15b_1p8>;
+		vddaon-supply = <&vreg_wcn_0p95>;
+		vdddig-supply = <&vreg_wcn_0p95>;
+		vddrfa1p2-supply = <&vreg_wcn_1p9>;
+		vddrfa1p8-supply = <&vreg_wcn_1p9>;
+
+		wlan-enable-gpios = <&tlmm 117 GPIO_ACTIVE_HIGH>;
+		bt-enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-0 = <&wcn_wlan_bt_en>;
+		pinctrl-names = "default";
+
+		regulators {
+			vreg_pmu_rfa_cmn: ldo0 {
+				regulator-name = "vreg_pmu_rfa_cmn";
+			};
+
+			vreg_pmu_aon_0p59: ldo1 {
+				regulator-name = "vreg_pmu_aon_0p59";
+			};
+
+			vreg_pmu_wlcx_0p8: ldo2 {
+				regulator-name = "vreg_pmu_wlcx_0p8";
+			};
+
+			vreg_pmu_wlmx_0p85: ldo3 {
+				regulator-name = "vreg_pmu_wlmx_0p85";
+			};
+
+			vreg_pmu_btcmx_0p85: ldo4 {
+				regulator-name = "vreg_pmu_btcmx_0p85";
+			};
+
+			vreg_pmu_rfa_0p8: ldo5 {
+				regulator-name = "vreg_pmu_rfa_0p8";
+			};
+
+			vreg_pmu_rfa_1p2: ldo6 {
+				regulator-name = "vreg_pmu_rfa_1p2";
+			};
+
+			vreg_pmu_rfa_1p8: ldo7 {
+				regulator-name = "vreg_pmu_rfa_1p8";
+			};
+
+			vreg_pmu_pcie_0p9: ldo8 {
+				regulator-name = "vreg_pmu_pcie_0p9";
+			};
+
+			vreg_pmu_pcie_1p8: ldo9 {
+				regulator-name = "vreg_pmu_pcie_1p8";
+			};
+		};
+	};
+};
+
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pm8550-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd-bob1-supply = <&vph_pwr>;
+		vdd-bob2-supply = <&vph_pwr>;
+		vdd-l1-l4-l10-supply = <&vreg_s4c_1p8>;
+		vdd-l2-l13-l14-supply = <&vreg_bob1>;
+		vdd-l5-l16-supply = <&vreg_bob1>;
+		vdd-l6-l7-supply = <&vreg_bob2>;
+		vdd-l8-l9-supply = <&vreg_bob1>;
+		vdd-l12-supply = <&vreg_s5j_1p2>;
+		vdd-l15-supply = <&vreg_s4c_1p8>;
+		vdd-l17-supply = <&vreg_bob2>;
+
+		vreg_bob1: bob1 {
+			regulator-name = "vreg_bob1";
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_bob2: bob2 {
+			regulator-name = "vreg_bob2";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1b_1p8: ldo1 {
+			regulator-name = "vreg_l1b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2b_3p0: ldo2 {
+			regulator-name = "vreg_l2b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3100000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4b_1p8: ldo4 {
+			regulator-name = "vreg_l4b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6b_1p8: ldo6 {
+			regulator-name = "vreg_l6b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7b_2p8: ldo7 {
+			regulator-name = "vreg_l7b_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8b_3p0: ldo8 {
+			regulator-name = "vreg_l8b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9b_2p9: ldo9 {
+			regulator-name = "vreg_l9b_2p9";
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12b_1p2: ldo12 {
+			regulator-name = "vreg_l12b_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l13b_3p0: ldo13 {
+			regulator-name = "vreg_l13b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3100000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l14b_3p0: ldo14 {
+			regulator-name = "vreg_l14b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l15b_1p8: ldo15 {
+			regulator-name = "vreg_l15b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vdd-l1-supply = <&vreg_s5j_1p2>;
+		vdd-l2-supply = <&vreg_s1f_0p7>;
+		vdd-l3-supply = <&vreg_s1f_0p7>;
+		vdd-s4-supply = <&vph_pwr>;
+
+		vreg_s4c_1p8: smps4 {
+			regulator-name = "vreg_s4c_1p8";
+			regulator-min-microvolt = <1856000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1c_1p2: ldo1 {
+			regulator-name = "vreg_l1c_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2c_0p8: ldo2 {
+			regulator-name = "vreg_l2c_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3c_0p8: ldo3 {
+			regulator-name = "vreg_l3c_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-2 {
+		compatible = "qcom,pmc8380-rpmh-regulators";
+		qcom,pmic-id = "d";
+
+		vdd-l1-supply = <&vreg_s1f_0p7>;
+		vdd-l2-supply = <&vreg_s1f_0p7>;
+		vdd-l3-supply = <&vreg_s4c_1p8>;
+		vdd-s1-supply = <&vph_pwr>;
+
+		vreg_l1d_0p8: ldo1 {
+			regulator-name = "vreg_l1d_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2d_0p9: ldo2 {
+			regulator-name = "vreg_l2d_0p9";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3d_1p8: ldo3 {
+			regulator-name = "vreg_l3d_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-3 {
+		compatible = "qcom,pmc8380-rpmh-regulators";
+		qcom,pmic-id = "e";
+
+		vdd-l2-supply = <&vreg_s1f_0p7>;
+		vdd-l3-supply = <&vreg_s5j_1p2>;
+
+		vreg_l2e_0p8: ldo2 {
+			regulator-name = "vreg_l2e_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3e_1p2: ldo3 {
+			regulator-name = "vreg_l3e_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-4 {
+		compatible = "qcom,pmc8380-rpmh-regulators";
+		qcom,pmic-id = "f";
+
+		vdd-l1-supply = <&vreg_s5j_1p2>;
+		vdd-l2-supply = <&vreg_s5j_1p2>;
+		vdd-l3-supply = <&vreg_s5j_1p2>;
+		vdd-s1-supply = <&vph_pwr>;
+
+		vreg_s1f_0p7: smps1 {
+			regulator-name = "vreg_s1f_0p7";
+			regulator-min-microvolt = <700000>;
+			regulator-max-microvolt = <1100000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-6 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "i";
+
+		vdd-l1-supply = <&vreg_s4c_1p8>;
+		vdd-l2-supply = <&vreg_s5j_1p2>;
+		vdd-l3-supply = <&vreg_s1f_0p7>;
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+
+		vreg_l1i_1p8: ldo1 {
+			regulator-name = "vreg_l1i_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2i_1p2: ldo2 {
+			regulator-name = "vreg_l2i_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3i_0p8: ldo3 {
+			regulator-name = "vreg_l3i_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-7 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "j";
+
+		vdd-l1-supply = <&vreg_s1f_0p7>;
+		vdd-l2-supply = <&vreg_s5j_1p2>;
+		vdd-l3-supply = <&vreg_s1f_0p7>;
+		vdd-s5-supply = <&vph_pwr>;
+
+		vreg_s5j_1p2: smps5 {
+			regulator-name = "vreg_s5j_1p2";
+			regulator-min-microvolt = <1256000>;
+			regulator-max-microvolt = <1304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1j_0p8: ldo1 {
+			regulator-name = "vreg_l1j_0p8";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2j_1p2: ldo2 {
+			regulator-name = "vreg_l2j_1p2";
+			regulator-min-microvolt = <1256000>;
+			regulator-max-microvolt = <1256000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3j_0p8: ldo3 {
+			regulator-name = "vreg_l3j_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+};
+
+&i2c0 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	keyboard@5 {
+		compatible = "hid-over-i2c";
+		reg = <0x5>;
+
+		hid-descr-addr = <0x20>;
+		interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-0 = <&kybd_default>;
+		pinctrl-names = "default";
+
+		wakeup-source;
+	};
+
+	touchpad@2c {
+		compatible = "hid-over-i2c";
+		reg = <0x2c>;
+
+		hid-descr-addr = <0x20>;
+		interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-0 = <&tpad_default>;
+		pinctrl-names = "default";
+
+		wakeup-source;
+	};
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	typec-mux@8 {
+		compatible = "parade,ps8833", "parade,ps8830";
+		reg = <0x8>;
+
+		clocks = <&rpmhcc RPMH_RF_CLK3>;
+
+		vdd-supply = <&vreg_rtmr0_1p15>;
+		vdd33-supply = <&vreg_rtmr0_3p3>;
+		vdd33-cap-supply = <&vreg_rtmr0_3p3>;
+		vddar-supply = <&vreg_rtmr0_1p15>;
+		vddat-supply = <&vreg_rtmr0_1p15>;
+		vddio-supply = <&vreg_rtmr0_1p8>;
+
+		reset-gpios = <&pm8550_gpios 10 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&rtmr0_default>;
+		pinctrl-names = "default";
+
+		retimer-switch;
+		orientation-switch;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				retimer_ss0_ss_out: endpoint {
+					remote-endpoint = <&pmic_glink_ss0_ss_in>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				retimer_ss0_ss_in: endpoint {
+					remote-endpoint = <&usb_1_ss0_qmpphy_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				retimer_ss0_con_sbu_out: endpoint {
+					remote-endpoint = <&pmic_glink_ss0_con_sbu_in>;
+				};
+			};
+		};
+	};
+};
+
+&i2c5 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	/* EC @0x3b */
+
+	/* Type A Port */
+	eusb3_typea_repeater: redriver@43 {
+		compatible = "nxp,ptn3222";
+		reg = <0x43>;
+		#phy-cells = <0>;
+
+		vdd3v3-supply = <&vreg_l13b_3p0>;
+		vdd1v8-supply = <&vreg_l4b_1p8>;
+
+		reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&eusb3_reset_n>;
+		pinctrl-names = "default";
+	};
+
+	/* Fingerprint scanner */
+	eusb5_frp_repeater: redriver@4f {
+		compatible = "nxp,ptn3222";
+		reg = <0x4f>;
+		#phy-cells = <0>;
+
+		vdd3v3-supply = <&vreg_l13b_3p0>;
+		vdd1v8-supply = <&vreg_l4b_1p8>;
+
+		reset-gpios = <&tlmm 184 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&eusb5_reset_n>;
+		pinctrl-names = "default";
+	};
+};
+
+&i2c7 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	typec-mux@8 {
+		compatible = "parade,ps8833", "parade,ps8830";
+		reg = <0x8>;
+
+		clocks = <&rpmhcc RPMH_RF_CLK4>;
+
+		vdd-supply = <&vreg_rtmr1_1p15>;
+		vdd33-supply = <&vreg_rtmr1_3p3>;
+		vdd33-cap-supply = <&vreg_rtmr1_3p3>;
+		vddar-supply = <&vreg_rtmr1_1p15>;
+		vddat-supply = <&vreg_rtmr1_1p15>;
+		vddio-supply = <&vreg_rtmr1_1p8>;
+
+		reset-gpios = <&tlmm 176 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&rtmr1_default>;
+		pinctrl-names = "default";
+
+		retimer-switch;
+		orientation-switch;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				retimer_ss1_ss_out: endpoint {
+					remote-endpoint = <&pmic_glink_ss1_ss_in>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				retimer_ss1_ss_in: endpoint {
+					remote-endpoint = <&usb_1_ss1_qmpphy_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				retimer_ss1_con_sbu_out: endpoint {
+					remote-endpoint = <&pmic_glink_ss1_con_sbu_in>;
+				};
+			};
+		};
+	};
+};
+
+&i2c8 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+};
+
+&i2c20 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+};
+
+&lpass_tlmm {
+	spkr_01_sd_n_active: spkr-01-sd-n-active-state {
+		pins = "gpio12";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+		output-low;
+	};
+
+	spkr_23_sd_n_active: spkr-23-sd-n-active-state {
+		pins = "gpio13";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+		output-low;
+	};
+};
+
+&lpass_vamacro {
+	pinctrl-0 = <&dmic01_default>;
+	pinctrl-names = "default";
+
+	vdd-micb-supply = <&vreg_l1b_1p8>;
+	qcom,dmic-sample-rate = <4800000>;
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dp0 {
+	status = "okay";
+};
+
+&mdss_dp0_out {
+	data-lanes = <0 1>;
+	link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+};
+
+&mdss_dp1 {
+	status = "okay";
+};
+
+&mdss_dp1_out {
+	data-lanes = <0 1>;
+	link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+};
+
+&mdss_dp3 {
+	/delete-property/ #sound-dai-cells;
+
+	status = "okay";
+
+	aux-bus {
+		panel {
+			compatible = "edp-panel";
+			enable-gpios = <&tlmm 74 GPIO_ACTIVE_HIGH>;
+			power-supply = <&vreg_edp_3p3>;
+
+			pinctrl-0 = <&edp_bl_en>;
+			pinctrl-names = "default";
+
+			port {
+				edp_panel_in: endpoint {
+					remote-endpoint = <&mdss_dp3_out>;
+				};
+			};
+		};
+	};
+
+	ports {
+		port@1 {
+			reg = <1>;
+
+			mdss_dp3_out: endpoint {
+				data-lanes = <0 1 2 3>;
+				link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+
+				remote-endpoint = <&edp_panel_in>;
+			};
+		};
+	};
+};
+
+&mdss_dp3_phy {
+	vdda-phy-supply = <&vreg_l3j_0p8>;
+	vdda-pll-supply = <&vreg_l2j_1p2>;
+
+	status = "okay";
+};
+
+&pcie4 {
+	perst-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>;
+
+	pinctrl-0 = <&pcie4_default>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie4_phy {
+	vdda-phy-supply = <&vreg_l3i_0p8>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&pcie4_port0 {
+	wifi@0 {
+		compatible = "pci17cb,1107";
+		reg = <0x10000 0x0 0x0 0x0 0x0>;
+
+		vddaon-supply = <&vreg_pmu_aon_0p59>;
+		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+		vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+		vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
+		vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
+	};
+};
+
+&pcie6a {
+	perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>;
+
+	vddpe-3v3-supply = <&vreg_nvme>;
+
+	pinctrl-0 = <&pcie6a_default>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie6a_phy {
+	vdda-phy-supply = <&vreg_l1d_0p8>;
+	vdda-pll-supply = <&vreg_l2j_1p2>;
+
+	status = "okay";
+};
+
+&pm8550_gpios {
+	rtmr0_default: rtmr0-reset-n-active-state {
+		pins = "gpio10";
+		function = "normal";
+		power-source = <1>; /* 1.8V */
+		bias-disable;
+		input-disable;
+		output-enable;
+	};
+
+	usb0_3p3_reg_en: usb0-3p3-reg-en-state {
+		pins = "gpio11";
+		function = "normal";
+		power-source = <1>; /* 1.8V */
+		bias-disable;
+		input-disable;
+		output-enable;
+	};
+};
+
+&pm8550ve_9_gpios {
+	usb0_1p8_reg_en: usb0-1p8-reg-en-state {
+		pins = "gpio8";
+		function = "normal";
+		power-source = <1>; /* 1.8V */
+		bias-disable;
+		input-disable;
+		output-enable;
+	};
+};
+
+&pmc8380_5_gpios {
+	usb0_pwr_1p15_reg_en: usb0-pwr-1p15-reg-en-state {
+		pins = "gpio8";
+		function = "normal";
+		power-source = <1>; /* 1.8V */
+		bias-disable;
+		input-disable;
+		output-enable;
+	};
+};
+
+&qupv3_0 {
+	status = "okay";
+};
+
+&qupv3_1 {
+	status = "okay";
+};
+
+&qupv3_2 {
+	status = "okay";
+};
+
+&sdhc_2 {
+	cd-gpios = <&tlmm 71 GPIO_ACTIVE_LOW>;
+	pinctrl-0 = <&sdc2_default &sdc2_card_det_n>;
+	pinctrl-1 = <&sdc2_sleep &sdc2_card_det_n>;
+	pinctrl-names = "default", "sleep";
+	vmmc-supply = <&vreg_l9b_2p9>;
+	vqmmc-supply = <&vreg_l6b_1p8>;
+	bus-width = <4>;
+	no-sdio;
+	no-mmc;
+
+	status = "okay";
+};
+
+&smb2360_0 {
+	status = "okay";
+};
+
+&smb2360_0_eusb2_repeater {
+	vdd18-supply = <&vreg_l3d_1p8>;
+	vdd3-supply = <&vreg_l2b_3p0>;
+};
+
+&smb2360_1 {
+	status = "okay";
+};
+
+&smb2360_1_eusb2_repeater {
+	vdd18-supply = <&vreg_l3d_1p8>;
+	vdd3-supply = <&vreg_l14b_3p0>;
+};
+
+&swr0 {
+	status = "okay";
+
+	pinctrl-0 = <&wsa_swr_active>, <&spkr_01_sd_n_active>;
+	pinctrl-names = "default";
+
+	/* WSA8845, Left Woofer */
+	left_woofer: speaker@0,0 {
+		compatible = "sdw20217020400";
+		reg = <0 0>;
+		reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "WooferLeft";
+		vdd-1p8-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l12b_1p2>;
+		qcom,port-mapping = <1 2 3 7 10 13>;
+	};
+
+	/* WSA8845, Left Tweeter */
+	left_tweeter: speaker@0,1 {
+		compatible = "sdw20217020400";
+		reg = <0 1>;
+		reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "TweeterLeft";
+		vdd-1p8-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l12b_1p2>;
+		qcom,port-mapping = <4 5 6 7 11 13>;
+	};
+};
+
+&swr1 {
+	status = "okay";
+
+	/* WCD9385 RX */
+	wcd_rx: codec@0,4 {
+		compatible = "sdw20217010d00";
+		reg = <0 4>;
+		qcom,rx-port-mapping = <1 2 3 4 5>;
+	};
+};
+
+&swr2 {
+	status = "okay";
+
+	/* WCD9385 TX */
+	wcd_tx: codec@0,3 {
+		compatible = "sdw20217010d00";
+		reg = <0 3>;
+		qcom,tx-port-mapping = <2 2 3 4>;
+	};
+};
+
+&swr3 {
+	status = "okay";
+
+	pinctrl-0 = <&wsa2_swr_active>, <&spkr_23_sd_n_active>;
+	pinctrl-names = "default";
+
+	/* WSA8845, Right Woofer */
+	right_woofer: speaker@0,0 {
+		compatible = "sdw20217020400";
+		reg = <0 0>;
+		reset-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "WooferRight";
+		vdd-1p8-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l12b_1p2>;
+		qcom,port-mapping = <1 2 3 7 10 13>;
+	};
+
+	/* WSA8845, Right Tweeter */
+	right_tweeter: speaker@0,1 {
+		compatible = "sdw20217020400";
+		reg = <0 1>;
+		reset-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "TweeterRight";
+		vdd-1p8-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l12b_1p2>;
+		qcom,port-mapping = <4 5 6 7 11 13>;
+	};
+};
+
+&tlmm {
+	gpio-reserved-ranges = <44 4>,  /* SPI11 (TPM) */
+			       <76 4>,  /* SPI19 (TZ Protected) */
+			       <238 1>; /* UFS Reset */
+
+	cam_rgb_default: cam-rgb-default-state {
+		mclk-pins {
+			pins = "gpio100";
+			function = "cam_aon";
+			drive-strength = <16>;
+			bias-disable;
+		};
+
+		reset-n-pins {
+			pins = "gpio237";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	cam_indicator_en: cam-indicator-en-state {
+		pins = "gpio110";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	cam_ldo_en: cam-ldo-en-state {
+		pins = "gpio91";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	edp_bl_en: edp-bl-en-state {
+		pins = "gpio74";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	edp_reg_en: edp-reg-en-state {
+		pins = "gpio70";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	eusb3_reset_n: eusb3-reset-n-state {
+		pins = "gpio6";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
+
+	eusb5_reset_n: eusb5-reset-n-state {
+		pins = "gpio184";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
+
+	hall_int_n_default: hall-int-n-state {
+		pins = "gpio92";
+		function = "gpio";
+
+		bias-disable;
+	};
+
+	kybd_default: kybd-default-state {
+		pins = "gpio67";
+		function = "gpio";
+		bias-pull-up;
+	};
+
+	nvme_reg_en: nvme-reg-en-state {
+		pins = "gpio18";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	pcie4_default: pcie4-default-state {
+		clkreq-n-pins {
+			pins = "gpio147";
+			function = "pcie4_clk";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		perst-n-pins {
+			pins = "gpio146";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		wake-n-pins {
+			pins = "gpio148";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	pcie6a_default: pcie6a-default-state {
+		clkreq-n-pins {
+			pins = "gpio153";
+			function = "pcie6a_clk";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		perst-n-pins {
+			pins = "gpio152";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		wake-n-pins {
+			pins = "gpio154";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	rtmr1_default: rtmr1-reset-n-active-state {
+		pins = "gpio176";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	sdc2_card_det_n: sdc2-card-det-state {
+		pins = "gpio71";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+
+	tpad_default: tpad-default-state {
+		disable-pins {
+			pins = "gpio38";
+			function = "gpio";
+			output-high;
+		};
+
+		int-n-pins {
+			pins = "gpio3";
+			function = "gpio";
+			bias-pull-up;
+		};
+
+		reset-n-pins {
+			pins = "gpio52";
+			function = "gpio";
+			bias-disable;
+		};
+	};
+
+	ts0_default: ts0-default-state {
+		disable-pins {
+			pins = "gpio75";
+			function = "gpio";
+			output-high;
+		};
+
+		int-n-pins {
+			pins = "gpio51";
+			function = "gpio";
+			bias-pull-up;
+		};
+
+		reset-n-pins {
+			/* Technically should be High-Z input */
+			pins = "gpio48";
+			function = "gpio";
+			output-low;
+			drive-strength = <2>;
+		};
+	};
+
+	usb1_pwr_1p15_reg_en: usb1-pwr-1p15-reg-en-state {
+		pins = "gpio188";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	usb1_pwr_1p8_reg_en: usb1-pwr-1p8-reg-en-state {
+		pins = "gpio175";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	usb1_pwr_3p3_reg_en: usb1-pwr-3p3-reg-en-state {
+		pins = "gpio186";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	wcd_default: wcd-reset-n-active-state {
+		pins = "gpio191";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+		output-low;
+	};
+
+	wcn_sw_en: wcn-sw-en-state {
+		pins = "gpio214";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	wcn_wlan_bt_en: wcn-wlan-bt-en-state {
+		pins = "gpio116", "gpio117";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
+
+&uart14 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn7850-bt";
+		max-speed = <3200000>;
+
+		vddaon-supply = <&vreg_pmu_aon_0p59>;
+		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+		vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+	};
+};
+
+&usb_1_ss0 {
+	status = "okay";
+};
+
+&usb_1_ss0_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_1_ss0_dwc3_hs {
+	remote-endpoint = <&pmic_glink_ss0_hs_in>;
+};
+
+&usb_1_ss0_hsphy {
+	vdd-supply = <&vreg_l3j_0p8>;
+	vdda12-supply = <&vreg_l2j_1p2>;
+
+	phys = <&smb2360_0_eusb2_repeater>;
+
+	status = "okay";
+};
+
+&usb_1_ss0_qmpphy {
+	vdda-phy-supply = <&vreg_l2j_1p2>;
+	vdda-pll-supply = <&vreg_l1j_0p8>;
+
+	status = "okay";
+};
+
+&usb_1_ss0_qmpphy_out {
+	remote-endpoint = <&retimer_ss0_ss_in>;
+};
+
+&usb_1_ss1 {
+	status = "okay";
+};
+
+&usb_1_ss1_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_1_ss1_dwc3_hs {
+	remote-endpoint = <&pmic_glink_ss1_hs_in>;
+};
+
+&usb_1_ss1_hsphy {
+	vdd-supply = <&vreg_l3j_0p8>;
+	vdda12-supply = <&vreg_l2j_1p2>;
+
+	phys = <&smb2360_1_eusb2_repeater>;
+
+	status = "okay";
+};
+
+&usb_1_ss1_qmpphy {
+	vdda-phy-supply = <&vreg_l2j_1p2>;
+	vdda-pll-supply = <&vreg_l2d_0p9>;
+
+	status = "okay";
+};
+
+&usb_1_ss1_qmpphy_out {
+	remote-endpoint = <&retimer_ss1_ss_in>;
+};
+
+&usb_2 {
+	status = "okay";
+};
+
+&usb_2_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_2_hsphy {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	phys = <&eusb5_frp_repeater>;
+
+	status = "okay";
+};
+
+&usb_mp {
+	status = "okay";
+};
+
+&usb_mp_dwc3 {
+	phys = <&usb_mp_hsphy0>, <&usb_mp_qmpphy0>;
+	phy-names = "usb2-0", "usb3-0";
+};
+
+&usb_mp_hsphy0 {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	phys = <&eusb3_typea_repeater>;
+
+	status = "okay";
+};
+
+&usb_mp_qmpphy0 {
+	vdda-phy-supply = <&vreg_l3e_1p2>;
+	vdda-pll-supply = <&vreg_l3c_0p8>;
+
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/qcom/x1e80100-dell-inspiron-14-plus-7441.dts b/arch/arm64/boot/dts/qcom/x1e80100-dell-inspiron-14-plus-7441.dts
new file mode 100644
index 000000000000..f728d298c72f
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/x1e80100-dell-inspiron-14-plus-7441.dts
@@ -0,0 +1,52 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2025 Val Packett <val@packett.cool>
+ */
+/dts-v1/;
+
+#include "x1e80100.dtsi"
+#include "x1-dell-thena.dtsi"
+
+/ {
+	model = "Dell Inspiron 14 Plus 7441";
+	compatible = "dell,inspiron-14-plus-7441", "qcom,x1e80100";
+};
+
+&sound {
+	model = "X1E80100-Dell-Inspiron-14p-7441";
+};
+
+&gpu {
+	status = "okay";
+};
+
+&gpu_zap_shader {
+	firmware-name = "qcom/x1e80100/dell/inspiron-14-plus-7441/qcdxkmsuc8380.mbn";
+};
+
+&i2c8 {
+	touchscreen@10 {
+		compatible = "hid-over-i2c";
+		reg = <0x10>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-0 = <&ts0_default>;
+		pinctrl-names = "default";
+	};
+};
+
+&remoteproc_adsp {
+	firmware-name = "qcom/x1e80100/dell/inspiron-14-plus-7441/qcadsp8380.mbn",
+			"qcom/x1e80100/dell/inspiron-14-plus-7441/adsp_dtbs.elf";
+
+	status = "okay";
+};
+
+&remoteproc_cdsp {
+	firmware-name = "qcom/x1e80100/dell/inspiron-14-plus-7441/qccdsp8380.mbn",
+			"qcom/x1e80100/dell/inspiron-14-plus-7441/cdsp_dtbs.elf";
+
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/qcom/x1e80100-dell-latitude-7455.dts b/arch/arm64/boot/dts/qcom/x1e80100-dell-latitude-7455.dts
new file mode 100644
index 000000000000..ace2a905e443
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/x1e80100-dell-latitude-7455.dts
@@ -0,0 +1,53 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2025 Val Packett <val@packett.cool>
+ */
+/dts-v1/;
+
+#include "x1e80100.dtsi"
+#include "x1-dell-thena.dtsi"
+
+/ {
+	model = "Dell Latitude 7455";
+	compatible = "dell,latitude-7455", "qcom,x1e80100";
+};
+
+&sound {
+	model = "X1E80100-Dell-Latitude-7455";
+};
+
+&gpu {
+	status = "okay";
+};
+
+&gpu_zap_shader {
+	firmware-name = "qcom/x1e80100/dell/latitude-7455/qcdxkmsuc8380.mbn";
+};
+
+&i2c8 {
+	/* LXST2021 */
+	touchscreen@9 {
+		compatible = "hid-over-i2c";
+		reg = <0x09>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-0 = <&ts0_default>;
+		pinctrl-names = "default";
+	};
+};
+
+&remoteproc_adsp {
+	firmware-name = "qcom/x1e80100/dell/latitude-7455/qcadsp8380.mbn",
+			"qcom/x1e80100/dell/latitude-7455/adsp_dtbs.elf";
+
+	status = "okay";
+};
+
+&remoteproc_cdsp {
+	firmware-name = "qcom/x1e80100/dell/latitude-7455/qccdsp8380.mbn",
+			"qcom/x1e80100/dell/latitude-7455/cdsp_dtbs.elf";
+
+	status = "okay";
+};
-- 
2.49.0

Re: [PATCH v3 3/5] arm64: dts: qcom: Add support for Dell Inspiron 7441 / Latitude 7455

[Konrad Dybcio]

On 7/6/25 10:50 PM, Val Packett wrote:
> From: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
> 
> Add device trees for both SKUs of the X1E80100 Thena laptop:
> - Dell Latitude 7455
> - Dell Inspiron 14 Plus 7441
> 
> Works:
> - Wi-Fi (WCN7850 hw2.0)
> - Bluetooth
> - USB Type-C x2 (with DP alt mode)
> - USB Type-A
> - USB Fingerprint reader
> - eDP Display (with brightness)
> - NVMe
> - SDHC (microSD slot)
> - Keyboard
> - Touchpad
> - Touchscreen
> - Audio (4 Speakers, 2 DMICs, Combo Jack)
> - Battery
> 
> Not included:
> - Camera
> 
> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
> Co-developed-by: Val Packett <val@packett.cool>
> Signed-off-by: Val Packett <val@packett.cool>
> ---

[...]

> +	wcd938x: audio-codec {
> +		compatible = "qcom,wcd9385-codec";
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&wcd_default>;

Please do:

property-n
property-names

consistently

[...]

> +&usb_mp_dwc3 {
> +	phys = <&usb_mp_hsphy0>, <&usb_mp_qmpphy0>;
> +	phy-names = "usb2-0", "usb3-0";
> +};

Let's not override this, so that the driver can still put the
remaining ones to sleep cleanly

Konrad

Re: [PATCH v3 3/5] arm64: dts: qcom: Add support for Dell Inspiron 7441 / Latitude 7455

[Val Packett]

On 7/14/25 10:35 AM, Konrad Dybcio wrote:
> On 7/6/25 10:50 PM, Val Packett wrote:
>> +	wcd938x: audio-codec {
>> +		compatible = "qcom,wcd9385-codec";
>> +
>> +		pinctrl-names = "default";
>> +		pinctrl-0 = <&wcd_default>;
> Please do:
>
> property-n
> property-names
Ack
>> +&usb_mp_dwc3 {
>> +	phys = <&usb_mp_hsphy0>, <&usb_mp_qmpphy0>;
>> +	phy-names = "usb2-0", "usb3-0";
>> +};
> Let's not override this, so that the driver can still put the
> remaining ones to sleep cleanly

This was added for a reason, after all-
Just tested booting without this, and the USB-A port does not work, with 
this in dmesg:

platform a400000.usb: deferred probe pending: dwc3: failed to initialize 
core

So it seems like the other ones "don't exist" / have been shut down 
completely by boot firmware(?)

Will add a clarifying comment.

~val

Re: [PATCH v3 3/5] arm64: dts: qcom: Add support for Dell Inspiron 7441 / Latitude 7455

[val]

On 7/15/25 3:00 PM, Val Packett <val@packett.cool> wrote:
> 
> On 7/14/25 10:35 AM, Konrad Dybcio wrote:
> > On 7/6/25 10:50 PM, Val Packett wrote:
> >> +&usb_mp_dwc3 {
> >> +    phys = <&usb_mp_hsphy0>, <&usb_mp_qmpphy0>;
> >> +    phy-names = "usb2-0", "usb3-0";
> >> +};
> > Let's not override this, so that the driver can still put the
> > remaining ones to sleep cleanly

[..]

> So it seems like the other ones "don't exist" / have been shut down 
> completely by boot firmware(?)

Oh, oops - that actually happens because the PHYs are disabled in the DT.

Looking at other laptops, x1e80100-hp-omnibook-x14.dts has the same chunk
that changes usb_mp_dwc3 to only have two PHYs, while x1e80100-dell-xps13-9345.dts
lists both PHYs, but only one of them has a repeater attached, while the other
one is empty.

I'll do the XPS thing, sure.

[PATCH v3 4/5] firmware: qcom: scm: Allow QSEECOM on Dell Inspiron 7441 / Latitude 7455

[Val Packett]

Allow these machines to access efivars through qseecom/uefisecapp.

Signed-off-by: Val Packett <val@packett.cool>
---
 drivers/firmware/qcom/qcom_scm.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/firmware/qcom/qcom_scm.c b/drivers/firmware/qcom/qcom_scm.c
index f63b716be5b0..b001208fefe0 100644
--- a/drivers/firmware/qcom/qcom_scm.c
+++ b/drivers/firmware/qcom/qcom_scm.c
@@ -1988,6 +1988,8 @@ static const struct of_device_id qcom_scm_qseecom_allowlist[] __maybe_unused = {
 	{ .compatible = "asus,vivobook-s15" },
 	{ .compatible = "asus,zenbook-a14-ux3407qa" },
 	{ .compatible = "asus,zenbook-a14-ux3407ra" },
+	{ .compatible = "dell,inspiron-14-plus-7441" },
+	{ .compatible = "dell,latitude-7455" },
 	{ .compatible = "dell,xps13-9345" },
 	{ .compatible = "hp,elitebook-ultra-g1q" },
 	{ .compatible = "hp,omnibook-x14" },
-- 
2.49.0

[PATCH v3 5/5] drm/panel-edp: Add BOE NE14QDM panel for Dell Latitude 7455

[Val Packett]

Cannot confirm which variant exactly it is, as the EDID alphanumeric data
contains '0RGNR' <0x80> 'NE14QDM' and ends there; but it's 60 Hz and with
touch.

I do not have access to datasheets for these panels, so the timing is
a guess that was tested to work fine on this laptop.

Raw EDID dump:

00 ff ff ff ff ff ff 00 09 e5 1e 0b 00 00 00 00
10 20 01 04 a5 1e 13 78 07 fd 85 a7 53 4c 9b 25
0f 50 54 00 00 00 01 01 01 01 01 01 01 01 01 01
01 01 01 01 01 01 a7 6d 00 a0 a0 40 78 60 30 20
36 00 2e bc 10 00 00 1a b9 57 00 a0 a0 40 78 60
30 20 36 00 2e bc 10 00 00 1a 00 00 00 fe 00 30
52 47 4e 52 80 4e 45 31 34 51 44 4d 00 00 00 00
00 02 41 31 a8 00 01 00 00 1a 41 0a 20 20 00 8f

Signed-off-by: Val Packett <val@packett.cool>
---
 drivers/gpu/drm/panel/panel-edp.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/gpu/drm/panel/panel-edp.c b/drivers/gpu/drm/panel/panel-edp.c
index 3796c41629cc..9a56e208cbdd 100644
--- a/drivers/gpu/drm/panel/panel-edp.c
+++ b/drivers/gpu/drm/panel/panel-edp.c
@@ -1939,6 +1939,7 @@ static const struct edp_panel_entry edp_panels[] = {
 	EDP_PANEL_ENTRY('B', 'O', 'E', 0x0ac5, &delay_200_500_e50, "NV116WHM-N4C"),
 	EDP_PANEL_ENTRY('B', 'O', 'E', 0x0ae8, &delay_200_500_e50_p2e80, "NV140WUM-N41"),
 	EDP_PANEL_ENTRY('B', 'O', 'E', 0x0b09, &delay_200_500_e50_po2e200, "NV140FHM-NZ"),
+	EDP_PANEL_ENTRY('B', 'O', 'E', 0x0b1e, &delay_200_500_e80, "NE140QDM-N6A"),
 	EDP_PANEL_ENTRY('B', 'O', 'E', 0x0b34, &delay_200_500_e80, "NV122WUM-N41"),
 	EDP_PANEL_ENTRY('B', 'O', 'E', 0x0b43, &delay_200_500_e200, "NV140FHM-T09"),
 	EDP_PANEL_ENTRY('B', 'O', 'E', 0x0b56, &delay_200_500_e80, "NT140FHM-N47"),
-- 
2.49.0

Re: [PATCH v3 5/5] drm/panel-edp: Add BOE NE14QDM panel for Dell Latitude 7455

[Doug Anderson]

Hi,

On Sun, Jul 6, 2025 at 1:59 PM Val Packett <val@packett.cool> wrote:
>
> Cannot confirm which variant exactly it is, as the EDID alphanumeric data
> contains '0RGNR' <0x80> 'NE14QDM' and ends there; but it's 60 Hz and with
> touch.
>
> I do not have access to datasheets for these panels, so the timing is
> a guess that was tested to work fine on this laptop.
>
> Raw EDID dump:
>
> 00 ff ff ff ff ff ff 00 09 e5 1e 0b 00 00 00 00
> 10 20 01 04 a5 1e 13 78 07 fd 85 a7 53 4c 9b 25
> 0f 50 54 00 00 00 01 01 01 01 01 01 01 01 01 01
> 01 01 01 01 01 01 a7 6d 00 a0 a0 40 78 60 30 20
> 36 00 2e bc 10 00 00 1a b9 57 00 a0 a0 40 78 60
> 30 20 36 00 2e bc 10 00 00 1a 00 00 00 fe 00 30
> 52 47 4e 52 80 4e 45 31 34 51 44 4d 00 00 00 00
> 00 02 41 31 a8 00 01 00 00 1a 41 0a 20 20 00 8f
>
> Signed-off-by: Val Packett <val@packett.cool>
> ---
>  drivers/gpu/drm/panel/panel-edp.c | 1 +
>  1 file changed, 1 insertion(+)

Reviewed-by: Douglas Anderson <dianders@chromium.org>

Pushed to drm-misc-next:

[5/5] drm/panel-edp: Add BOE NE14QDM panel for Dell Latitude 7455
      commit: 1a304a2f8f7dbe25f555721f502227f9197145ed

Re: [PATCH v3 0/5] Add Dell Inspiron 7441 / Latitude 7455 (X1E-80-100)

[Laurentiu Tudor]

Hi Val,

On 7/6/25 23:50, Val Packett wrote:
> The unified series for Dell Thena laptops.
> 
> Changes since v2[1]:
> 
> - Fixed From/Co-developed-by on the big patch
> - Fixed one remaining "inspirIon"
> - Fixed codec/cpu alphabetical order in audio nodes (copy-paste..)
> - Made the common dtsi an 'x1-' one in preparation for x1p models
> 
> [1]: https://lore.kernel.org/all/20250701231643.568854-1-val@packett.cool/
> 
> Bryan O'Donoghue (2):
>    dt-bindings: arm: qcom: Add Dell Inspiron 14 Plus 7441
>    arm64: dts: qcom: Add support for Dell Inspiron 7441 / Latitude 7455
> 
> Val Packett (3):
>    dt-bindings: arm: qcom: Add Dell Latitude 7455
>    firmware: qcom: scm: Allow QSEECOM on Dell Inspiron 7441 / Latitude
>      7455
>    drm/panel-edp: Add BOE NE14QDM panel for Dell Latitude 7455
> 
>   .../devicetree/bindings/arm/qcom.yaml         |    2 +
>   arch/arm64/boot/dts/qcom/Makefile             |    4 +
>   arch/arm64/boot/dts/qcom/x1-dell-thena.dtsi   | 1657 +++++++++++++++++
>   .../x1e80100-dell-inspiron-14-plus-7441.dts   |   52 +
>   .../dts/qcom/x1e80100-dell-latitude-7455.dts  |   53 +
>   drivers/firmware/qcom/qcom_scm.c              |    2 +
>   drivers/gpu/drm/panel/panel-edp.c             |    1 +
>   7 files changed, 1771 insertions(+)
>   create mode 100644 arch/arm64/boot/dts/qcom/x1-dell-thena.dtsi
>   create mode 100644 arch/arm64/boot/dts/qcom/x1e80100-dell-inspiron-14-plus-7441.dts
>   create mode 100644 arch/arm64/boot/dts/qcom/x1e80100-dell-latitude-7455.dts
> 

Thanks much for the effort!
For the series:

Reviewed-by: Laurentiu Tudor <laurentiu.tudor1@dell.com>