From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
To: dri-devel@lists.freedesktop.org
Cc: John Stultz <john.stultz@linaro.org>,
lkml <linux-kernel@vger.kernel.org>,
Wolfram Sang <wsa+renesas@sang-engineering.com>
Subject: Re: [PATCH 0/5 v3] adv7511 EDID probing improvements
Date: Mon, 16 Jan 2017 17:57:02 +0200 [thread overview]
Message-ID: <9649749.TAVrhOzo15@avalon> (raw)
In-Reply-To: <1483472502-16403-1-git-send-email-john.stultz@linaro.org>
Hi John,
Thank you for the patches.
On Tuesday 03 Jan 2017 11:41:37 John Stultz wrote:
> Hope everyone had a good newyears!
>
> Wanted to re-send out v3 of this patch set improving the EDID
> probing on the adv7511 used on HiKey, for consideration for
> merging for 4.11
>
> The first three patches are fixups that are hopefully straight
> forward, integrating feedback I got from Laurant.
>
> The last two patches try to clean up and resue code, which as
> a side effect avoids an issue I'm seeing where something is
> going wrong with the regmap cache state for the
> ADV7511_REG_EDID_I2C_ADDR(0x43) register which results in
> i2c_transfer errors if we don't do the
> regcache_sync/_mark_dirty() calls. I suspect there might be a
> better solution there, but have not gotten any other suggestions
> so I wanted to go ahead and submit these.
>
> Thoughts and feedback would be appreciated!
For the whole series,
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> New in v3:
> * Addressed naming improvements and drm_kms_helper_hotplug_event
> usage corrections as suggested by Laurent.
>
> Cc: David Airlie <airlied@linux.ie>
> Cc: Archit Taneja <architt@codeaurora.org>
> Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
> Cc: Lars-Peter Clausen <lars@metafoo.de>
> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Cc: dri-devel@lists.freedesktop.org
>
> Archit Taneja (1):
> drm/bridge: adv7511: Enable HPD interrupts to support hotplug and
> improve monitor detection
>
> John Stultz (4):
> drm/bridge: adv7511: Use work_struct to defer hotplug handing to out
> of irq context
> drm/bridge: adv7511: Switch to using drm_kms_helper_hotplug_event()
> drm/bridge: adv7511: Rework adv7511_power_on/off() so they can be
> reused internally
> drm/bridge: adv7511: Reuse __adv7511_power_on/off() when probing EDID
>
> drivers/gpu/drm/bridge/adv7511/adv7511.h | 2 +
> drivers/gpu/drm/bridge/adv7511/adv7511_drv.c | 62
> +++++++++++++++++++--------- 2 files changed, 44 insertions(+), 20
> deletions(-)
--
Regards,
Laurent Pinchart
prev parent reply other threads:[~2017-01-16 15:56 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-01-03 19:41 [PATCH 0/5 v3] adv7511 EDID probing improvements John Stultz
2017-01-03 19:41 ` [PATCH 1/5 v3] drm/bridge: adv7511: Use work_struct to defer hotplug handing to out of irq context John Stultz
2017-01-03 19:41 ` [PATCH 2/5 v3] drm/bridge: adv7511: Switch to using drm_kms_helper_hotplug_event() John Stultz
2017-01-16 15:47 ` Laurent Pinchart
2017-01-16 15:56 ` Laurent Pinchart
2017-01-16 19:31 ` John Stultz
2017-01-03 19:41 ` [PATCH 3/5 v3] drm/bridge: adv7511: Enable HPD interrupts to support hotplug and improve monitor detection John Stultz
2017-01-03 19:41 ` [PATCH 4/5 v3] drm/bridge: adv7511: Rework adv7511_power_on/off() so they can be reused internally John Stultz
2017-01-16 15:50 ` Laurent Pinchart
2017-01-03 19:41 ` [PATCH 5/5 v3] drm/bridge: adv7511: Reuse __adv7511_power_on/off() when probing EDID John Stultz
2017-01-16 16:03 ` Laurent Pinchart
2017-01-16 20:14 ` John Stultz
2017-01-16 22:25 ` Laurent Pinchart
2017-01-16 23:16 ` [RFC][PATCH] drm/bridge: adv7511: Re-write the i2c address as it may have been lost John Stultz
2017-01-16 23:36 ` Laurent Pinchart
2017-01-16 23:39 ` John Stultz
2017-01-11 8:48 ` [PATCH 0/5 v3] adv7511 EDID probing improvements Archit Taneja
2017-01-12 0:06 ` John Stultz
2017-01-12 4:22 ` Archit Taneja
2017-01-16 15:57 ` Laurent Pinchart [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=9649749.TAVrhOzo15@avalon \
--to=laurent.pinchart@ideasonboard.com \
--cc=dri-devel@lists.freedesktop.org \
--cc=john.stultz@linaro.org \
--cc=linux-kernel@vger.kernel.org \
--cc=wsa+renesas@sang-engineering.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox