* [PATCH v2 0/2] media: i2c: Add ov2735 camera sensor driver
@ 2025-07-08 10:25 Hardevsinh Palaniya
2025-07-08 10:25 ` [PATCH v2 1/2] dt-bindings: media: i2c: Add ov2735 sensor Hardevsinh Palaniya
2025-07-08 10:25 ` [PATCH v2 2/2] media: i2c: add ov2735 image sensor driver Hardevsinh Palaniya
0 siblings, 2 replies; 10+ messages in thread
From: Hardevsinh Palaniya @ 2025-07-08 10:25 UTC (permalink / raw)
To: sakari.ailus, andriy.shevchenko, krzk+dt
Cc: Hardevsinh Palaniya, Himanshu Bhavani, Mauro Carvalho Chehab,
Rob Herring, Conor Dooley, Hans Verkuil, André Apitzsch,
Ricardo Ribalda, Hans de Goede, Sylvain Petinot, Tarang Raval,
Jingjing Xiong, Dongcheng Yan, Benjamin Mugnier,
Heimir Thor Sverrisson, Arnd Bergmann, Matthias Fend,
Bryan O'Donoghue, linux-media, devicetree, linux-kernel
Add a v4l2 subdevice driver for the Omnivision OV2735 sensor.
The Omnivision OV2735 is a 1/2.7-Inch CMOS image sensor with an
active array size of 1920 x 1080.
The following features are supported:
- Manual exposure an gain control support
- vblank/hblank control support
- Test pattern support control
- Supported resolution: 1920 x 1080 @ 30fps (SGRBG10)
The driver is tested on mainline branch v6.14-rc6 on IMX8MP Debix Model a.
v1 -> v2
- Added necessary header files
- Corrected indentation
- Used the ret parameter in cci_write and cci_read functions
Hardevsinh Palaniya (1):
media: i2c: add ov2735 image sensor driver
Himanshu Bhavani (1):
dt-bindings: media: i2c: Add ov2735 sensor
.../bindings/media/i2c/ovti,ov2735.yaml | 104 ++
MAINTAINERS | 9 +
drivers/media/i2c/Kconfig | 10 +
drivers/media/i2c/Makefile | 1 +
drivers/media/i2c/ov2735.c | 908 ++++++++++++++++++
5 files changed, 1032 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/i2c/ovti,ov2735.yaml
create mode 100644 drivers/media/i2c/ov2735.c
--
2.34.1
^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH v2 1/2] dt-bindings: media: i2c: Add ov2735 sensor
2025-07-08 10:25 [PATCH v2 0/2] media: i2c: Add ov2735 camera sensor driver Hardevsinh Palaniya
@ 2025-07-08 10:25 ` Hardevsinh Palaniya
2025-07-08 10:41 ` Krzysztof Kozlowski
2025-07-08 10:25 ` [PATCH v2 2/2] media: i2c: add ov2735 image sensor driver Hardevsinh Palaniya
1 sibling, 1 reply; 10+ messages in thread
From: Hardevsinh Palaniya @ 2025-07-08 10:25 UTC (permalink / raw)
To: sakari.ailus, andriy.shevchenko, krzk+dt
Cc: Himanshu Bhavani, Hardevsinh Palaniya, Mauro Carvalho Chehab,
Rob Herring, Conor Dooley, Hans Verkuil, Ricardo Ribalda,
André Apitzsch, Hans de Goede, Sylvain Petinot,
Jingjing Xiong, Benjamin Mugnier, Dongcheng Yan,
Heimir Thor Sverrisson, Matthias Fend, Arnd Bergmann,
Bryan O'Donoghue, You-Sheng Yang, linux-media, devicetree,
linux-kernel
From: Himanshu Bhavani <himanshu.bhavani@siliconsignals.io>
Add bindings for Omnivision OV2735 sensor.
Signed-off-by: Himanshu Bhavani <himanshu.bhavani@siliconsignals.io>
---
.../bindings/media/i2c/ovti,ov2735.yaml | 104 ++++++++++++++++++
1 file changed, 104 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/i2c/ovti,ov2735.yaml
diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov2735.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov2735.yaml
new file mode 100644
index 000000000000..a6be7886f4d6
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov2735.yaml
@@ -0,0 +1,104 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/ovti,ov2735.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: OmniVision OV2735 Image Sensor
+
+maintainers:
+ - Himanshu Bhavani <himanshu.bhavani@siliconsignals.io>
+
+description: |
+ The OmniVision OV2735 is a 2MP (1920x1080) color CMOS image sensor controlled
+ through an I2C-compatible SCCB bus. it outputs RAW10 format and uses a 1/2.7"
+ optical format.
+
+properties:
+ compatible:
+ const: ovti,ov2735
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: XVCLK clock
+
+ clock-names:
+ items:
+ - const: xvclk
+
+ AVDD-supply:
+ description: Analog Domain Power Supply
+
+ DOVDD-supply:
+ description: I/O Domain Power Supply
+
+ DVDD-supply:
+ description: Digital Domain Power Supply
+
+ reset-gpios:
+ maxItems: 1
+ description: Reset Pin GPIO Control (active low)
+
+ pwdn-gpios:
+ maxItems: 1
+ description: Powerdown Pin GPIO Control (active low)
+
+ port:
+ description: MIPI CSI-2 transmitter port
+ $ref: /schemas/graph.yaml#/$defs/port-base
+ additionalProperties: false
+
+ properties:
+ endpoint:
+ $ref: /schemas/media/video-interfaces.yaml#
+ unevaluatedProperties: false
+
+ properties:
+ data-lanes:
+ items:
+ - const: 1
+ - const: 2
+
+ required:
+ - data-lanes
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - port
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/rk3399-cru.h>
+ #include <dt-bindings/gpio/gpio.h>
+
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ camera-sensor@3c {
+ compatible = "ovti,ov2735";
+ reg = <0x3c>;
+ clocks = <&ov2735_clk>;
+
+ assigned-clocks = <&ov2735_clk>;
+ assigned-clock-parents = <&ov2735_clk_parent>;
+ assigned-clock-rates = <24000000>;
+
+ reset-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+ pwdn-gpios = <&gpio2 11 GPIO_ACTIVE_LOW>;
+
+ port {
+ cam_out: endpoint {
+ remote-endpoint = <&mipi_in_cam>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
+ };
--
2.34.1
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v2 2/2] media: i2c: add ov2735 image sensor driver
2025-07-08 10:25 [PATCH v2 0/2] media: i2c: Add ov2735 camera sensor driver Hardevsinh Palaniya
2025-07-08 10:25 ` [PATCH v2 1/2] dt-bindings: media: i2c: Add ov2735 sensor Hardevsinh Palaniya
@ 2025-07-08 10:25 ` Hardevsinh Palaniya
2025-07-08 10:42 ` Krzysztof Kozlowski
` (2 more replies)
1 sibling, 3 replies; 10+ messages in thread
From: Hardevsinh Palaniya @ 2025-07-08 10:25 UTC (permalink / raw)
To: sakari.ailus, andriy.shevchenko, krzk+dt
Cc: Hardevsinh Palaniya, Himanshu Bhavani, Mauro Carvalho Chehab,
Rob Herring, Conor Dooley, Hans Verkuil, André Apitzsch,
Hans de Goede, Ricardo Ribalda, Heimir Thor Sverrisson,
Matthias Fend, Benjamin Mugnier, Jingjing Xiong, Sylvain Petinot,
Dongcheng Yan, Arnd Bergmann, Bryan O'Donoghue, linux-media,
devicetree, linux-kernel
Add a v4l2 subdevice driver for the Omnivision OV2735 sensor.
The Omnivision OV2735 is a 1/2.7-Inch CMOS image sensor with an
active array size of 1920 x 1080.
The following features are supported:
- Manual exposure an gain control support
- vblank/hblank control support
- Test pattern support control
- Supported resolution: 1920 x 1080 @ 30fps (SGRBG10)
Co-developed-by: Himanshu Bhavani <himanshu.bhavani@siliconsignals.io>
Signed-off-by: Himanshu Bhavani <himanshu.bhavani@siliconsignals.io>
Signed-off-by: Hardevsinh Palaniya <hardevsinh.palaniya@siliconsignals.io>
---
MAINTAINERS | 9 +
drivers/media/i2c/Kconfig | 10 +
drivers/media/i2c/Makefile | 1 +
drivers/media/i2c/ov2735.c | 908 +++++++++++++++++++++++++++++++++++++
4 files changed, 928 insertions(+)
create mode 100644 drivers/media/i2c/ov2735.c
diff --git a/MAINTAINERS b/MAINTAINERS
index 92e9d8c7708f..058bbfd9523b 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -18471,6 +18471,15 @@ T: git git://linuxtv.org/media.git
F: Documentation/devicetree/bindings/media/i2c/ovti,ov2685.yaml
F: drivers/media/i2c/ov2685.c
+OMNIVISION OV2735 SENSOR DRIVER
+M: Hardevsinh Palaniya <hardevsinh.palaniya@siliconsignals.io>
+M: Himanshu Bhavani <himanshu.bhavani@siliconsignals.io>
+L: linux-media@vger.kernel.org
+S: Maintained
+T: git git://linuxtv.org/media.git
+F: Documentation/devicetree/bindings/media/i2c/ovti,ov2735.yaml
+F: drivers/media/i2c/ov2735.c
+
OMNIVISION OV2740 SENSOR DRIVER
M: Tianshu Qiu <tian.shu.qiu@intel.com>
R: Sakari Ailus <sakari.ailus@linux.intel.com>
diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
index 4b4c199da6ea..9646eab1b177 100644
--- a/drivers/media/i2c/Kconfig
+++ b/drivers/media/i2c/Kconfig
@@ -446,6 +446,16 @@ config VIDEO_OV2685
To compile this driver as a module, choose M here: the
module will be called ov2685.
+config VIDEO_OV2735
+ tristate "OmniVision OV2735 sensor support"
+ select V4L2_CCI_I2C
+ help
+ This is a Video4Linux2 sensor driver for the Sony
+ OV2735 camera.
+
+ To compile this driver as a module, choose M here: the
+ module will be called ov2735.
+
config VIDEO_OV2740
tristate "OmniVision OV2740 sensor support"
depends on ACPI || COMPILE_TEST
diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
index 5873d29433ee..1adb27743fa1 100644
--- a/drivers/media/i2c/Makefile
+++ b/drivers/media/i2c/Makefile
@@ -93,6 +93,7 @@ obj-$(CONFIG_VIDEO_OV2640) += ov2640.o
obj-$(CONFIG_VIDEO_OV2659) += ov2659.o
obj-$(CONFIG_VIDEO_OV2680) += ov2680.o
obj-$(CONFIG_VIDEO_OV2685) += ov2685.o
+obj-$(CONFIG_VIDEO_OV2735) += ov2735.o
obj-$(CONFIG_VIDEO_OV2740) += ov2740.o
obj-$(CONFIG_VIDEO_OV4689) += ov4689.o
obj-$(CONFIG_VIDEO_OV5640) += ov5640.o
diff --git a/drivers/media/i2c/ov2735.c b/drivers/media/i2c/ov2735.c
new file mode 100644
index 000000000000..a7df516eaedc
--- /dev/null
+++ b/drivers/media/i2c/ov2735.c
@@ -0,0 +1,908 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * V4L2 Support for the OV2735
+ *
+ * Copyright (C) 2025 Silicon Signals Pvt. Ltd.
+ *
+ * Based on Rockchip ov2735 Camera Driver
+ * Copyright (C) 2017 Fuzhou Rockchip Electronics Co., Ltd.
+ *
+ * Inspired from ov8858, imx219, imx283 camera drivers
+ */
+
+#include <linux/array_size.h>
+#include <linux/clk.h>
+#include <linux/container_of.h>
+#include <linux/delay.h>
+#include <linux/device/devres.h>
+#include <linux/err.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/pm_runtime.h>
+#include <linux/property.h>
+#include <linux/regulator/consumer.h>
+#include <linux/units.h>
+#include <linux/types.h>
+
+#include <media/v4l2-cci.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-fwnode.h>
+#include <media/v4l2-mediabus.h>
+
+#define OV2735_XCLK_FREQ (24 * HZ_PER_MHZ)
+
+#define OV2735_REG_PAGE_SELECT CCI_REG8(0xfd)
+
+/* Page 0 */
+#define OV2735_REG_CHIPID CCI_REG16(0x02)
+#define OV2735_CHIPID 0x2735
+
+#define OV2735_REG_SOFT_REST CCI_REG8(0x20)
+
+/* Clock Settings */
+#define OV2735_REG_PLL_CTRL CCI_REG8(0x2f)
+#define OV2735_REG_PLL_OUTDIV CCI_REG8(0x34)
+#define OV2735_REG_CLK_MODE CCI_REG8(0x30)
+#define OV2735_REG_CLOCK_REG1 CCI_REG8(0x33)
+#define OV2735_REG_CLOCK_REG2 CCI_REG8(0x35)
+
+/* Page 1 */
+#define OV2735_REG_STREAM_CTRL CCI_REG8(0xa0)
+#define OV2735_STREAM_ON 0x01
+#define OV2735_STREAM_OFF 0x00
+
+#define OV2735_REG_UPDOWN_MIRROR CCI_REG8(0x3f)
+#define OV2735_REG_BINNING_DAC_CODE_MODE CCI_REG8(0x30)
+#define OV2735_REG_FRAME_LENGTH CCI_REG16(0x0e)
+#define OV2735_VTS_MAX 0x0fff
+#define OV2735_REG_FRAME_EXP_SEPERATE_EN CCI_REG8(0x0d)
+#define OV2735_FRAME_EXP_SEPERATE_EN 0x10
+#define OV2735_REG_FRAME_SYNC CCI_REG8(0x01)
+
+#define OV2735_REG_HBLANK CCI_REG16(0x09)
+
+#define OV2735_REG_HS_MIPI CCI_REG8(0xb1)
+#define OV2735_REG_MIPI_CTRL1 CCI_REG8(0x92)
+#define OV2735_REG_MIPI_CTRL2 CCI_REG8(0x94)
+#define OV2735_REG_MIPI_CTRL3 CCI_REG8(0xa1)
+#define OV2735_REG_MIPI_CTRL4 CCI_REG8(0xb2)
+#define OV2735_REG_MIPI_CTRL5 CCI_REG8(0xb3)
+#define OV2735_REG_MIPI_CTRL6 CCI_REG8(0xb4)
+#define OV2735_REG_MIPI_CTRL7 CCI_REG8(0xb5)
+#define OV2735_REG_PREPARE CCI_REG8(0x95)
+#define OV2735_REG_R_HS_ZERO CCI_REG8(0x96)
+#define OV2735_REG_TRAIL CCI_REG8(0x98)
+#define OV2735_REG_R_CLK_ZERO CCI_REG8(0x9c)
+#define OV2735_REG_MIPI_V_SIZE CCI_REG16(0x8e)
+#define OV2735_REG_MIPI_H_SIZE CCI_REG16(0x90)
+
+#define OV2735_REG_ANALOG_CTRL3 CCI_REG8(0x25)
+#define OV2735_REG_VNCP CCI_REG8(0x20)
+
+/* BLC registers */
+#define OV2735_REG_BLC_GAIN_BLUE CCI_REG8(0x86)
+#define OV2735_REG_BLC_GAIN_RED CCI_REG8(0x87)
+#define OV2735_REG_BLC_GAIN_GR CCI_REG8(0x88)
+#define OV2735_REG_BLC_GAIN_GB CCI_REG8(0x89)
+#define OV2735_REG_GB_SUBOFFSET CCI_REG8(0xf0)
+#define OV2735_REG_BLUE_SUBOFFSET CCI_REG8(0xf1)
+#define OV2735_REG_RED_SUBOFFSET CCI_REG8(0xf2)
+#define OV2735_REG_GR_SUBOFFSET CCI_REG8(0xf3)
+#define OV2735_REG_BLC_BPC_TH_P CCI_REG8(0xfc)
+#define OV2735_REG_BLC_BPC_TH_N CCI_REG8(0xfe)
+
+#define OV2735_REG_TEST_PATTERN CCI_REG8(0xb2)
+#define OV2735_TEST_PATTERN_ENABLE 0x01
+#define OV2735_TEST_PATTERN_DISABLE 0xfe
+
+#define OV2735_REG_LONG_EXPOSURE CCI_REG16(0x03)
+#define OV2735_EXPOSURE_MIN 4
+#define OV2735_EXPOSURE_STEP 1
+
+#define OV2735_REG_ANALOG_GAIN CCI_REG8(0x24)
+#define OV2735_ANALOG_GAIN_MIN 0x10
+#define OV2735_ANALOG_GAIN_MAX 0xff
+#define OV2735_ANALOG_GAIN_STEP 1
+#define OV2735_ANALOG_GAIN_DEFAULT 0x10
+
+/* Page 2 */
+#define OV2735_REG_V_START CCI_REG16(0xa0)
+#define OV2735_REG_V_SIZE CCI_REG16(0xa2)
+#define OV2735_REG_H_START CCI_REG16(0xa4)
+#define OV2735_REG_H_SIZE CCI_REG16(0xa6)
+
+#define OV2735_LINK_FREQ_420MHZ (420 * HZ_PER_MHZ)
+#define OV2735_PIXEL_RATE (168 * HZ_PER_MHZ)
+
+static const char * const ov2735_supply_name[] = {
+ "AVDD", /* Analog power */
+ "DOVDD", /* Digital I/O power */
+ "DVDD", /* Digital core power */
+};
+
+struct ov2735 {
+ struct device *dev;
+ struct regmap *cci;
+ struct v4l2_subdev sd;
+ struct media_pad pad;
+ struct i2c_client *client;
+ struct clk *xclk;
+ struct gpio_desc *reset_gpio;
+ struct gpio_desc *pwdn_gpio;
+ struct regulator_bulk_data supplies[ARRAY_SIZE(ov2735_supply_name)];
+
+ /* V4L2 Controls */
+ struct v4l2_ctrl_handler handler;
+ struct v4l2_ctrl *link_freq;
+ struct v4l2_ctrl *pixel_rate;
+ struct v4l2_ctrl *hblank;
+ struct v4l2_ctrl *vblank;
+ struct v4l2_ctrl *gain;
+ struct v4l2_ctrl *exposure;
+ struct v4l2_ctrl *test_pattern;
+};
+
+struct ov2735_reglist {
+ unsigned int num_regs;
+ const struct cci_reg_sequence *regvals;
+};
+
+struct ov2735_mode {
+ u32 width;
+ u32 height;
+ u32 hts_def;
+ u32 vts_def;
+ u32 exp_def;
+ struct ov2735_reglist reg_list;
+};
+
+static struct cci_reg_sequence ov2735_1920_1080_30fps[] = {
+ { OV2735_REG_PAGE_SELECT, 0x00 },
+ { OV2735_REG_PLL_CTRL, 0x10 },
+ { OV2735_REG_PLL_OUTDIV, 0x00 },
+ { OV2735_REG_CLK_MODE, 0x15 },
+ { OV2735_REG_CLOCK_REG1, 0x01 },
+ { OV2735_REG_CLOCK_REG2, 0x20 },
+ { OV2735_REG_PAGE_SELECT, 0x01 },
+ { OV2735_REG_BINNING_DAC_CODE_MODE, 0x00 },
+ { CCI_REG8(0xfb), 0x73 },
+ { OV2735_REG_FRAME_SYNC, 0x01 },
+ { OV2735_REG_PAGE_SELECT, 0x01 },
+
+ /* Timing ctrl */
+ { CCI_REG8(0x1a), 0x6b },
+ { CCI_REG8(0x1c), 0xea },
+ { CCI_REG8(0x16), 0x0c },
+ { CCI_REG8(0x21), 0x00 },
+ { CCI_REG8(0x11), 0x63 },
+ { CCI_REG8(0x19), 0xc3 },
+
+ /* Analog ctrl */
+ { CCI_REG8(0x26), 0x5a },
+ { CCI_REG8(0x29), 0x01 },
+ { CCI_REG8(0x33), 0x6f },
+ { CCI_REG8(0x2a), 0xd2 },
+ { CCI_REG8(0x2c), 0x40 },
+ { CCI_REG8(0xd0), 0x02 },
+ { CCI_REG8(0xd1), 0x01 },
+ { CCI_REG8(0xd2), 0x20 },
+ { CCI_REG8(0xd3), 0x04 },
+ { CCI_REG8(0xd4), 0x2a },
+ { CCI_REG8(0x50), 0x00 },
+ { CCI_REG8(0x51), 0x2c },
+ { CCI_REG8(0x52), 0x29 },
+ { CCI_REG8(0x53), 0x00 },
+ { CCI_REG8(0x55), 0x44 },
+ { CCI_REG8(0x58), 0x29 },
+ { CCI_REG8(0x5a), 0x00 },
+ { CCI_REG8(0x5b), 0x00 },
+ { CCI_REG8(0x5d), 0x00 },
+ { CCI_REG8(0x64), 0x2f },
+ { CCI_REG8(0x66), 0x62 },
+ { CCI_REG8(0x68), 0x5b },
+ { CCI_REG8(0x75), 0x46 },
+ { CCI_REG8(0x76), 0x36 },
+ { CCI_REG8(0x77), 0x4f },
+ { CCI_REG8(0x78), 0xef },
+ { CCI_REG8(0x72), 0xcf },
+ { CCI_REG8(0x73), 0x36 },
+ { CCI_REG8(0x7d), 0x0d },
+ { CCI_REG8(0x7e), 0x0d },
+ { CCI_REG8(0x8a), 0x77 },
+ { CCI_REG8(0x8b), 0x77 },
+
+ { OV2735_REG_PAGE_SELECT, 0x01 },
+ { OV2735_REG_HS_MIPI, 0x83 },
+ { OV2735_REG_MIPI_CTRL5, 0x0b },
+ { OV2735_REG_MIPI_CTRL6, 0x14 },
+ { CCI_REG8(0x9d), 0x40 },
+ { OV2735_REG_MIPI_CTRL3, 0x05 },
+ { OV2735_REG_MIPI_CTRL2, 0x44 },
+ { OV2735_REG_PREPARE, 0x33 },
+ { OV2735_REG_R_HS_ZERO, 0x1f },
+ { OV2735_REG_TRAIL, 0x45 },
+ { OV2735_REG_R_CLK_ZERO, 0x10 },
+ { OV2735_REG_MIPI_CTRL7, 0x70 },
+ { OV2735_REG_ANALOG_CTRL3, 0xe0 },
+ { OV2735_REG_VNCP, 0x7b },
+
+ /* BLC */
+ { OV2735_REG_PAGE_SELECT, 0x01 },
+ { OV2735_REG_BLC_GAIN_BLUE, 0x77 },
+ { OV2735_REG_BLC_GAIN_GB, 0x77 },
+ { OV2735_REG_BLC_GAIN_RED, 0x74 },
+ { OV2735_REG_BLC_GAIN_GR, 0x74 },
+ { OV2735_REG_BLC_BPC_TH_P, 0xe0 },
+ { OV2735_REG_BLC_BPC_TH_N, 0xe0 },
+ { OV2735_REG_GB_SUBOFFSET, 0x40 },
+ { OV2735_REG_BLUE_SUBOFFSET, 0x40 },
+ { OV2735_REG_RED_SUBOFFSET, 0x40 },
+ { OV2735_REG_GR_SUBOFFSET, 0x40 },
+
+ /* 1920x1080 */
+ { OV2735_REG_PAGE_SELECT, 0x02 },
+ { OV2735_REG_V_START, 0x0008 },
+ { OV2735_REG_V_SIZE, 0x0438 },
+ { OV2735_REG_H_START, 0x0008 },
+ { OV2735_REG_H_SIZE, 0x03c0 },
+ { OV2735_REG_PAGE_SELECT, 0x01 },
+ { OV2735_REG_MIPI_V_SIZE, 0x0780 },
+ { OV2735_REG_MIPI_H_SIZE, 0x0438 },
+};
+
+static const struct ov2735_mode supported_modes[] = {
+ {
+ .width = 1920,
+ .height = 1080,
+ .exp_def = 399,
+ .hts_def = 2200,
+ .vts_def = 2545,
+ .reg_list = {
+ .num_regs = ARRAY_SIZE(ov2735_1920_1080_30fps),
+ .regvals = ov2735_1920_1080_30fps,
+ },
+ },
+};
+
+static const s64 link_freq_menu_items[] = {
+ OV2735_LINK_FREQ_420MHZ,
+};
+
+static const char * const ov2735_test_pattern_menu[] = {
+ "Disabled",
+ "Vertical Color",
+};
+
+static const u32 ov2735_mbus_codes[] = {
+ MEDIA_BUS_FMT_SGRBG10_1X10,
+};
+
+static inline struct ov2735 *to_ov2735(struct v4l2_subdev *_sd)
+{
+ return container_of(_sd, struct ov2735, sd);
+}
+
+static int ov2735_enable_test_pattern(struct ov2735 *ov2735, u32 pattern)
+{
+ int ret = 0;
+ u64 val;
+
+ cci_read(ov2735->cci, OV2735_REG_TEST_PATTERN, &val, &ret);
+ if (ret)
+ return ret;
+
+ switch (pattern) {
+ case 0:
+ val &= ~OV2735_TEST_PATTERN_ENABLE;
+ break;
+ case 1:
+ val |= OV2735_TEST_PATTERN_ENABLE;
+ break;
+ }
+
+ return cci_write(ov2735->cci, OV2735_REG_TEST_PATTERN, val, NULL);
+}
+
+static int ov2735_set_ctrl(struct v4l2_ctrl *ctrl)
+{
+ struct ov2735 *ov2735 = container_of(ctrl->handler, struct ov2735,
+ handler);
+ const struct ov2735_mode *mode;
+ struct v4l2_mbus_framefmt *fmt;
+ struct v4l2_subdev_state *state;
+ u64 vts;
+ int ret = 0;
+
+ state = v4l2_subdev_get_locked_active_state(&ov2735->sd);
+ fmt = v4l2_subdev_state_get_format(state, 0);
+
+ mode = v4l2_find_nearest_size(supported_modes,
+ ARRAY_SIZE(supported_modes),
+ width, height,
+ fmt->width, fmt->height);
+
+ if (ctrl->id == V4L2_CID_VBLANK) {
+ /* Honour the VBLANK limits when setting exposure. */
+ s64 max = mode->height + ctrl->val - 4;
+
+ ret = __v4l2_ctrl_modify_range(ov2735->exposure,
+ ov2735->exposure->minimum, max,
+ ov2735->exposure->step,
+ ov2735->exposure->default_value);
+ if (ret)
+ return ret;
+ }
+
+ /*
+ * Applying V4L2 control value only happens
+ * when power is up for streaming.
+ */
+ if (pm_runtime_get_if_in_use(ov2735->dev) == 0)
+ return 0;
+
+ cci_write(ov2735->cci, OV2735_REG_PAGE_SELECT, 0x01, &ret);
+
+ switch (ctrl->id) {
+ case V4L2_CID_EXPOSURE:
+ cci_write(ov2735->cci, OV2735_REG_LONG_EXPOSURE, ctrl->val, &ret);
+ break;
+ case V4L2_CID_ANALOGUE_GAIN:
+ cci_write(ov2735->cci, OV2735_REG_ANALOG_GAIN, ctrl->val, &ret);
+ break;
+ case V4L2_CID_HBLANK:
+ cci_write(ov2735->cci, OV2735_REG_HBLANK, ctrl->val, &ret);
+ break;
+ case V4L2_CID_VBLANK:
+ vts = ctrl->val + mode->height;
+ cci_write(ov2735->cci, OV2735_REG_FRAME_EXP_SEPERATE_EN,
+ OV2735_FRAME_EXP_SEPERATE_EN, &ret);
+ cci_write(ov2735->cci, OV2735_REG_FRAME_LENGTH, vts, &ret);
+ break;
+ case V4L2_CID_TEST_PATTERN:
+ ret = ov2735_enable_test_pattern(ov2735, ctrl->val);
+ break;
+ default:
+ dev_err(ov2735->dev, "ctrl(id:0x%x, val:0x%x) is not handled\n",
+ ctrl->id, ctrl->val);
+ break;
+ }
+ cci_write(ov2735->cci, OV2735_REG_FRAME_SYNC, 0x01, &ret);
+
+ pm_runtime_put(ov2735->dev);
+
+ return ret;
+}
+
+static const struct v4l2_ctrl_ops ov2735_ctrl_ops = {
+ .s_ctrl = ov2735_set_ctrl,
+};
+
+static int ov2735_init_controls(struct ov2735 *ov2735)
+{
+ struct v4l2_ctrl_handler *ctrl_hdlr;
+ struct v4l2_fwnode_device_properties props;
+ const struct ov2735_mode *mode = &supported_modes[0];
+ u64 hblank_def, vblank_def, exp_max;
+ int ret;
+
+ ctrl_hdlr = &ov2735->handler;
+ ret = v4l2_ctrl_handler_init(ctrl_hdlr, 7);
+ if (ret)
+ return ret;
+
+ ov2735->pixel_rate = v4l2_ctrl_new_std(ctrl_hdlr, &ov2735_ctrl_ops,
+ V4L2_CID_PIXEL_RATE, 0, OV2735_PIXEL_RATE,
+ 1, OV2735_PIXEL_RATE);
+
+ ov2735->link_freq = v4l2_ctrl_new_int_menu(ctrl_hdlr, &ov2735_ctrl_ops,
+ V4L2_CID_LINK_FREQ,
+ 0, 0, link_freq_menu_items);
+ if (ov2735->link_freq)
+ ov2735->link_freq->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+
+ hblank_def = mode->hts_def - mode->width;
+ ov2735->hblank = v4l2_ctrl_new_std(ctrl_hdlr, &ov2735_ctrl_ops, V4L2_CID_HBLANK,
+ hblank_def, hblank_def, 1, hblank_def);
+
+ vblank_def = mode->vts_def - mode->height;
+ ov2735->vblank = v4l2_ctrl_new_std(ctrl_hdlr, &ov2735_ctrl_ops,
+ V4L2_CID_VBLANK, vblank_def,
+ OV2735_VTS_MAX - mode->height,
+ 1, vblank_def);
+
+ exp_max = mode->vts_def - 4;
+ ov2735->exposure = v4l2_ctrl_new_std(ctrl_hdlr, &ov2735_ctrl_ops,
+ V4L2_CID_EXPOSURE, OV2735_EXPOSURE_MIN,
+ exp_max, OV2735_EXPOSURE_STEP, mode->exp_def);
+
+ ov2735->gain = v4l2_ctrl_new_std(ctrl_hdlr, &ov2735_ctrl_ops,
+ V4L2_CID_ANALOGUE_GAIN, OV2735_ANALOG_GAIN_MIN,
+ OV2735_ANALOG_GAIN_MAX, OV2735_ANALOG_GAIN_STEP,
+ OV2735_ANALOG_GAIN_DEFAULT);
+
+ ov2735->test_pattern = v4l2_ctrl_new_std_menu_items(ctrl_hdlr,
+ &ov2735_ctrl_ops, V4L2_CID_TEST_PATTERN,
+ ARRAY_SIZE(ov2735_test_pattern_menu) - 1,
+ 0, 0, ov2735_test_pattern_menu);
+ if (ctrl_hdlr->error) {
+ ret = ctrl_hdlr->error;
+ dev_err(ov2735->dev, "control init failed (%d)\n", ret);
+ goto err_handler_free;
+ }
+
+ ret = v4l2_fwnode_device_parse(ov2735->dev, &props);
+ if (ret)
+ goto err_handler_free;
+
+ ret = v4l2_ctrl_new_fwnode_properties(ctrl_hdlr, &ov2735_ctrl_ops,
+ &props);
+ if (ret)
+ goto err_handler_free;
+
+ ov2735->sd.ctrl_handler = ctrl_hdlr;
+
+ return 0;
+
+err_handler_free:
+ v4l2_ctrl_handler_free(ctrl_hdlr);
+
+ return ret;
+}
+
+static int ov2735_enable_streams(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state, u32 pad,
+ u64 streams_mask)
+{
+ struct ov2735 *ov2735 = to_ov2735(sd);
+ const struct ov2735_mode *mode;
+ const struct ov2735_reglist *reg_list;
+ const struct v4l2_mbus_framefmt *fmt;
+ int ret;
+
+ fmt = v4l2_subdev_state_get_format(state, 0);
+ mode = v4l2_find_nearest_size(supported_modes,
+ ARRAY_SIZE(supported_modes),
+ width, height,
+ fmt->width, fmt->height);
+
+ ret = pm_runtime_resume_and_get(ov2735->dev);
+ if (ret < 0)
+ return ret;
+
+ reg_list = &mode->reg_list;
+ cci_multi_reg_write(ov2735->cci, reg_list->regvals, reg_list->num_regs, &ret);
+ if (ret) {
+ dev_err(ov2735->dev, "%s failed to send mfg header\n", __func__);
+ goto err_rpm_put;
+ }
+
+ /* Apply customized values from user */
+ ret = __v4l2_ctrl_handler_setup(ov2735->sd.ctrl_handler);
+ if (ret)
+ goto err_rpm_put;
+
+ /* set stream on register */
+ cci_write(ov2735->cci, OV2735_REG_PAGE_SELECT, 0x01, &ret);
+ cci_write(ov2735->cci, OV2735_REG_STREAM_CTRL, OV2735_STREAM_ON, &ret);
+ if (ret)
+ goto err_rpm_put;
+
+ return 0;
+
+err_rpm_put:
+ pm_runtime_put(ov2735->dev);
+ return ret;
+}
+
+static int ov2735_disable_streams(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state, u32 pad,
+ u64 streams_mask)
+{
+ struct ov2735 *ov2735 = to_ov2735(sd);
+ int ret = 0;
+
+ /* set stream off register */
+ cci_write(ov2735->cci, OV2735_REG_PAGE_SELECT, 0x01, &ret);
+ cci_write(ov2735->cci, OV2735_REG_STREAM_CTRL, OV2735_STREAM_OFF, &ret);
+ if (ret)
+ dev_err(ov2735->dev, "%s failed to set stream\n", __func__);
+
+ pm_runtime_put(ov2735->dev);
+
+ return ret;
+}
+
+static int ov2735_enum_mbus_code(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *sd_state,
+ struct v4l2_subdev_mbus_code_enum *code)
+{
+ if (code->index >= ARRAY_SIZE(ov2735_mbus_codes))
+ return -EINVAL;
+
+ code->code = ov2735_mbus_codes[code->index];
+
+ return 0;
+}
+
+static int ov2735_enum_frame_size(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *sd_state,
+ struct v4l2_subdev_frame_size_enum *fse)
+{
+ u32 code;
+
+ if (fse->index >= ARRAY_SIZE(supported_modes))
+ return -EINVAL;
+
+ code = MEDIA_BUS_FMT_SGRBG10_1X10;
+ if (fse->code != code)
+ return -EINVAL;
+
+ fse->min_width = supported_modes[fse->index].width;
+ fse->max_width = fse->min_width;
+ fse->min_height = supported_modes[fse->index].height;
+ fse->max_height = fse->min_height;
+
+ return 0;
+}
+
+static void ov2735_set_framing_limits(struct ov2735 *ov2735,
+ const struct ov2735_mode *mode)
+{
+ u32 hblank, vblank_def;
+
+ hblank = mode->hts_def - mode->width;
+ __v4l2_ctrl_modify_range(ov2735->hblank, hblank, hblank, 1, hblank);
+
+ vblank_def = mode->vts_def - mode->height;
+ __v4l2_ctrl_modify_range(ov2735->vblank, vblank_def, OV2735_VTS_MAX - mode->height,
+ 1, vblank_def);
+}
+
+static int ov2735_set_pad_format(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *sd_state,
+ struct v4l2_subdev_format *fmt)
+{
+ struct v4l2_mbus_framefmt *format;
+ const struct ov2735_mode *mode;
+ struct ov2735 *ov2735 = to_ov2735(sd);
+
+ format = v4l2_subdev_state_get_format(sd_state, 0);
+
+ mode = v4l2_find_nearest_size(supported_modes,
+ ARRAY_SIZE(supported_modes),
+ width, height,
+ fmt->format.width, fmt->format.height);
+
+ fmt->format.width = mode->width;
+ fmt->format.height = mode->height;
+ fmt->format.field = V4L2_FIELD_NONE;
+ fmt->format.colorspace = V4L2_COLORSPACE_RAW;
+ fmt->format.quantization = V4L2_QUANTIZATION_FULL_RANGE;
+ fmt->format.xfer_func = V4L2_XFER_FUNC_NONE;
+
+ format = v4l2_subdev_state_get_format(sd_state, 0);
+
+ if (fmt->which == V4L2_SUBDEV_FORMAT_ACTIVE)
+ ov2735_set_framing_limits(ov2735, mode);
+
+ *format = fmt->format;
+
+ return 0;
+}
+
+static int ov2735_init_state(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state)
+{
+ struct v4l2_subdev_format fmt = {
+ .which = V4L2_SUBDEV_FORMAT_TRY,
+ .pad = 0,
+ .format = {
+ .code = MEDIA_BUS_FMT_SGRBG10_1X10,
+ .width = supported_modes[0].width,
+ .height = supported_modes[0].height,
+ },
+ };
+
+ ov2735_set_pad_format(sd, state, &fmt);
+
+ return 0;
+}
+
+static const struct v4l2_subdev_video_ops ov2735_video_ops = {
+ .s_stream = v4l2_subdev_s_stream_helper,
+};
+
+static const struct v4l2_subdev_pad_ops ov2735_pad_ops = {
+ .enum_mbus_code = ov2735_enum_mbus_code,
+ .get_fmt = v4l2_subdev_get_fmt,
+ .set_fmt = ov2735_set_pad_format,
+ .enum_frame_size = ov2735_enum_frame_size,
+ .enable_streams = ov2735_enable_streams,
+ .disable_streams = ov2735_disable_streams,
+};
+
+static const struct v4l2_subdev_ops ov2735_subdev_ops = {
+ .video = &ov2735_video_ops,
+ .pad = &ov2735_pad_ops,
+};
+
+static const struct v4l2_subdev_internal_ops ov2735_internal_ops = {
+ .init_state = ov2735_init_state,
+};
+
+static int ov2735_power_on(struct device *dev)
+{
+ struct v4l2_subdev *sd = dev_get_drvdata(dev);
+ struct ov2735 *ov2735 = to_ov2735(sd);
+ unsigned long delay_us;
+ int ret;
+
+ gpiod_set_value_cansleep(ov2735->pwdn_gpio, 0);
+ fsleep(3000);
+
+ ret = regulator_bulk_enable(ARRAY_SIZE(ov2735_supply_name),
+ ov2735->supplies);
+ if (ret) {
+ dev_err(ov2735->dev, "failed to enable regulators\n");
+ return ret;
+ }
+
+ gpiod_set_value_cansleep(ov2735->pwdn_gpio, 1);
+ fsleep(3000);
+
+ gpiod_set_value_cansleep(ov2735->reset_gpio, 0);
+ fsleep(3000);
+
+ ret = clk_prepare_enable(ov2735->xclk);
+ if (ret) {
+ dev_err(ov2735->dev, "failed to enable clock\n");
+ goto err_regulator_off;
+ }
+
+ /* 8192 cycles prior to first SCCB transaction */
+ delay_us = DIV_ROUND_UP(8192, OV2735_XCLK_FREQ / 1000 / 1000);
+ fsleep(delay_us);
+
+ return 0;
+
+err_regulator_off:
+ regulator_bulk_disable(ARRAY_SIZE(ov2735_supply_name), ov2735->supplies);
+ return ret;
+}
+
+static int ov2735_power_off(struct device *dev)
+{
+ struct v4l2_subdev *sd = dev_get_drvdata(dev);
+ struct ov2735 *ov2735 = to_ov2735(sd);
+
+ gpiod_set_value_cansleep(ov2735->pwdn_gpio, 1);
+ clk_disable_unprepare(ov2735->xclk);
+ gpiod_set_value_cansleep(ov2735->reset_gpio, 0);
+ regulator_bulk_disable(ARRAY_SIZE(ov2735_supply_name), ov2735->supplies);
+
+ return 0;
+}
+
+static int ov2735_get_regulators(struct ov2735 *ov2735)
+{
+ unsigned int i;
+
+ for (i = 0; i < ARRAY_SIZE(ov2735_supply_name); i++)
+ ov2735->supplies[i].supply = ov2735_supply_name[i];
+
+ return devm_regulator_bulk_get(ov2735->dev,
+ ARRAY_SIZE(ov2735_supply_name),
+ ov2735->supplies);
+}
+
+static int ov2735_identify_module(struct ov2735 *ov2735)
+{
+ u64 chip_id;
+ int ret = 0;
+
+ cci_write(ov2735->cci, OV2735_REG_PAGE_SELECT, 0x00, &ret);
+ cci_read(ov2735->cci, OV2735_REG_CHIPID, &chip_id, &ret);
+ if (ret)
+ return dev_err_probe(ov2735->dev, ret, "failed to read chip id %x\n",
+ OV2735_CHIPID);
+
+ if (chip_id != OV2735_CHIPID)
+ return dev_err_probe(ov2735->dev, -EIO, "chip id mismatch: %x!=%llx\n",
+ OV2735_CHIPID, chip_id);
+
+ return 0;
+}
+
+static int ov2735_parse_endpoint(struct ov2735 *ov2735)
+{
+ struct fwnode_handle *fwnode;
+ struct v4l2_fwnode_endpoint bus_cfg = {
+ .bus_type = V4L2_MBUS_CSI2_DPHY,
+ };
+ struct fwnode_handle *ep;
+ int ret;
+
+ fwnode = dev_fwnode(ov2735->dev);
+ ep = fwnode_graph_get_next_endpoint(fwnode, NULL);
+ if (!ep) {
+ dev_err(ov2735->dev, "Failed to get next endpoint\n");
+ return -ENXIO;
+ }
+
+ ret = v4l2_fwnode_endpoint_alloc_parse(ep, &bus_cfg);
+ fwnode_handle_put(ep);
+ if (ret)
+ return ret;
+
+ if (bus_cfg.bus.mipi_csi2.num_data_lanes != 2) {
+ dev_err_probe(ov2735->dev, -EINVAL, "only 2 data lanes are supported\n");
+ goto error_out;
+ }
+
+ return 0;
+
+error_out:
+ v4l2_fwnode_endpoint_free(&bus_cfg);
+
+ return ret;
+};
+
+static int ov2735_probe(struct i2c_client *client)
+{
+ struct ov2735 *ov2735;
+ unsigned int xclk_freq;
+ int ret;
+
+ ov2735 = devm_kzalloc(&client->dev, sizeof(*ov2735), GFP_KERNEL);
+ if (!ov2735)
+ return -ENOMEM;
+
+ ov2735->client = client;
+ ov2735->dev = &client->dev;
+
+ v4l2_i2c_subdev_init(&ov2735->sd, client, &ov2735_subdev_ops);
+ ov2735->sd.internal_ops = &ov2735_internal_ops;
+
+ ov2735->cci = devm_cci_regmap_init_i2c(client, 8);
+ if (IS_ERR(ov2735->cci)) {
+ ret = PTR_ERR(ov2735->cci);
+ return dev_err_probe(ov2735->dev, ret, "failed to initialize CCI\n");
+ }
+
+ /* Get system clock (xvclk) */
+ ov2735->xclk = devm_v4l2_sensor_clk_get(ov2735->dev, NULL);
+ if (IS_ERR(ov2735->xclk)) {
+ return dev_err_probe(ov2735->dev, PTR_ERR(ov2735->xclk),
+ "failed to get xclk\n");
+ }
+
+ xclk_freq = clk_get_rate(ov2735->xclk);
+ if (xclk_freq != OV2735_XCLK_FREQ)
+ return dev_err_probe(ov2735->dev, -EINVAL,
+ "xclk frequency not supported: %d Hz\n",
+ xclk_freq);
+
+ ret = ov2735_get_regulators(ov2735);
+ if (ret)
+ return dev_err_probe(ov2735->dev, ret, "failed to get regulators\n");
+
+ ret = ov2735_parse_endpoint(ov2735);
+ if (ret) {
+ dev_err(ov2735->dev, "failed to parse endpoint configuration\n");
+ return ret;
+ }
+
+ ov2735->reset_gpio = devm_gpiod_get(&client->dev, "reset", GPIOD_OUT_LOW);
+ if (IS_ERR(ov2735->reset_gpio))
+ return dev_err_probe(ov2735->dev, PTR_ERR(ov2735->reset_gpio),
+ "failed to get reset GPIO\n");
+
+ ov2735->pwdn_gpio = devm_gpiod_get(&client->dev, "pwdn", GPIOD_OUT_LOW);
+ if (IS_ERR(ov2735->pwdn_gpio))
+ return dev_err_probe(ov2735->dev, PTR_ERR(ov2735->pwdn_gpio),
+ "failed to get reset GPIO\n");
+
+ ret = ov2735_power_on(ov2735->dev);
+ if (ret)
+ return ret;
+
+ ret = ov2735_identify_module(ov2735);
+ if (ret)
+ goto error_power_off;
+
+ /* This needs the pm runtime to be registered. */
+ ret = ov2735_init_controls(ov2735);
+ if (ret)
+ goto error_power_off;
+
+ /* Initialize subdev */
+ ov2735->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+ ov2735->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR;
+ ov2735->pad.flags = MEDIA_PAD_FL_SOURCE;
+
+ ret = media_entity_pads_init(&ov2735->sd.entity, 1, &ov2735->pad);
+ if (ret) {
+ dev_err_probe(ov2735->dev, ret, "failed to init entity pads\n");
+ goto error_handler_free;
+ }
+
+ ov2735->sd.state_lock = ov2735->handler.lock;
+ ret = v4l2_subdev_init_finalize(&ov2735->sd);
+ if (ret < 0) {
+ dev_err_probe(ov2735->dev, ret, "subdev init error\n");
+ goto error_media_entity;
+ }
+
+ pm_runtime_set_active(ov2735->dev);
+ pm_runtime_enable(ov2735->dev);
+
+ ret = v4l2_async_register_subdev_sensor(&ov2735->sd);
+ if (ret < 0) {
+ dev_err_probe(ov2735->dev, ret,
+ "failed to register ov2735 sub-device\n");
+ goto error_subdev_cleanup;
+ }
+
+ pm_runtime_idle(ov2735->dev);
+
+ return 0;
+
+error_subdev_cleanup:
+ v4l2_subdev_cleanup(&ov2735->sd);
+ pm_runtime_disable(ov2735->dev);
+ pm_runtime_set_suspended(ov2735->dev);
+
+error_media_entity:
+ media_entity_cleanup(&ov2735->sd.entity);
+
+error_handler_free:
+ v4l2_ctrl_handler_free(ov2735->sd.ctrl_handler);
+
+error_power_off:
+ ov2735_power_off(ov2735->dev);
+
+ return ret;
+}
+
+static void ov2735_remove(struct i2c_client *client)
+{
+ struct v4l2_subdev *sd = i2c_get_clientdata(client);
+ struct ov2735 *ov2735 = to_ov2735(sd);
+
+ v4l2_async_unregister_subdev(sd);
+ v4l2_subdev_cleanup(&ov2735->sd);
+ media_entity_cleanup(&sd->entity);
+ v4l2_ctrl_handler_free(ov2735->sd.ctrl_handler);
+
+ pm_runtime_disable(ov2735->dev);
+ if (!pm_runtime_status_suspended(ov2735->dev))
+ ov2735_power_off(ov2735->dev);
+ pm_runtime_set_suspended(ov2735->dev);
+}
+
+static DEFINE_RUNTIME_DEV_PM_OPS(ov2735_pm_ops,
+ ov2735_power_off, ov2735_power_on, NULL);
+
+static const struct of_device_id ov2735_id[] = {
+ { .compatible = "ovti,ov2735" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, ov2735_id);
+
+static struct i2c_driver ov2735_driver = {
+ .driver = {
+ .name = "ov2735",
+ .pm = pm_ptr(&ov2735_pm_ops),
+ .of_match_table = ov2735_id,
+ },
+ .probe = ov2735_probe,
+ .remove = ov2735_remove,
+};
+module_i2c_driver(ov2735_driver);
+
+MODULE_DESCRIPTION("OV2735 Camera Sensor Driver");
+MODULE_AUTHOR("Hardevsinh Palaniya <hardevsinh.palaniya@siliconsignals.io>");
+MODULE_AUTHOR("Himanshu Bhavani <himanshu.bhavani@siliconsignals.io>");
+MODULE_LICENSE("GPL");
--
2.34.1
^ permalink raw reply related [flat|nested] 10+ messages in thread
* Re: [PATCH v2 1/2] dt-bindings: media: i2c: Add ov2735 sensor
2025-07-08 10:25 ` [PATCH v2 1/2] dt-bindings: media: i2c: Add ov2735 sensor Hardevsinh Palaniya
@ 2025-07-08 10:41 ` Krzysztof Kozlowski
2025-07-10 7:18 ` Hardevsinh Palaniya
0 siblings, 1 reply; 10+ messages in thread
From: Krzysztof Kozlowski @ 2025-07-08 10:41 UTC (permalink / raw)
To: Hardevsinh Palaniya, sakari.ailus, andriy.shevchenko, krzk+dt
Cc: Himanshu Bhavani, Mauro Carvalho Chehab, Rob Herring,
Conor Dooley, Hans Verkuil, Ricardo Ribalda, André Apitzsch,
Hans de Goede, Sylvain Petinot, Jingjing Xiong, Benjamin Mugnier,
Dongcheng Yan, Heimir Thor Sverrisson, Matthias Fend,
Arnd Bergmann, Bryan O'Donoghue, You-Sheng Yang, linux-media,
devicetree, linux-kernel
On 08/07/2025 12:25, Hardevsinh Palaniya wrote:
> +
> + clocks:
> + items:
> + - description: XVCLK clock
> +
> + clock-names:
> + items:
> + - const: xvclk
> +
> + AVDD-supply:
Use lowercase everywhere.
> + description: Analog Domain Power Supply
> +
> + DOVDD-supply:
> + description: I/O Domain Power Supply
> +
> + DVDD-supply:
> + description: Digital Domain Power Supply
> +
> + reset-gpios:
> + maxItems: 1
> + description: Reset Pin GPIO Control (active low)
> +
> + pwdn-gpios:
Use instead recommended name from the gpio-consumer-common.yaml.
> + maxItems: 1
> + description: Powerdown Pin GPIO Control (active low)
> +
> + port:
> + description: MIPI CSI-2 transmitter port
> + $ref: /schemas/graph.yaml#/$defs/port-base
> + additionalProperties: false
> +
> + properties:
> + endpoint:
> + $ref: /schemas/media/video-interfaces.yaml#
> + unevaluatedProperties: false
> +
> + properties:
> + data-lanes:
> + items:
> + - const: 1
> + - const: 2
> +
> + required:
> + - data-lanes
> +
> +required:
> + - compatible
> + - reg
> + - clocks
> + - port
Supplies should be required. Devices rarely work without power.
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH v2 2/2] media: i2c: add ov2735 image sensor driver
2025-07-08 10:25 ` [PATCH v2 2/2] media: i2c: add ov2735 image sensor driver Hardevsinh Palaniya
@ 2025-07-08 10:42 ` Krzysztof Kozlowski
2025-07-08 11:28 ` Hardevsinh Palaniya
2025-07-08 11:40 ` Kieran Bingham
2025-07-08 13:25 ` Dave Stevenson
2 siblings, 1 reply; 10+ messages in thread
From: Krzysztof Kozlowski @ 2025-07-08 10:42 UTC (permalink / raw)
To: Hardevsinh Palaniya, sakari.ailus, andriy.shevchenko, krzk+dt
Cc: Himanshu Bhavani, Mauro Carvalho Chehab, Rob Herring,
Conor Dooley, Hans Verkuil, André Apitzsch, Hans de Goede,
Ricardo Ribalda, Heimir Thor Sverrisson, Matthias Fend,
Benjamin Mugnier, Jingjing Xiong, Sylvain Petinot, Dongcheng Yan,
Arnd Bergmann, Bryan O'Donoghue, linux-media, devicetree,
linux-kernel
On 08/07/2025 12:25, Hardevsinh Palaniya wrote:
> +
> +static const struct v4l2_subdev_ops ov2735_subdev_ops = {
> + .video = &ov2735_video_ops,
> + .pad = &ov2735_pad_ops,
> +};
> +
> +static const struct v4l2_subdev_internal_ops ov2735_internal_ops = {
> + .init_state = ov2735_init_state,
> +};
> +
> +static int ov2735_power_on(struct device *dev)
> +{
> + struct v4l2_subdev *sd = dev_get_drvdata(dev);
> + struct ov2735 *ov2735 = to_ov2735(sd);
> + unsigned long delay_us;
> + int ret;
> +
> + gpiod_set_value_cansleep(ov2735->pwdn_gpio, 0);
So you power up here...
> + fsleep(3000);
> +
> + ret = regulator_bulk_enable(ARRAY_SIZE(ov2735_supply_name),
> + ov2735->supplies);
> + if (ret) {
> + dev_err(ov2735->dev, "failed to enable regulators\n");
> + return ret;
> + }
> +
> + gpiod_set_value_cansleep(ov2735->pwdn_gpio, 1);
And here you power down your device. This makes no sense... unless this
is not a power down GPIO.
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH v2 2/2] media: i2c: add ov2735 image sensor driver
2025-07-08 10:42 ` Krzysztof Kozlowski
@ 2025-07-08 11:28 ` Hardevsinh Palaniya
2025-07-08 13:26 ` Krzysztof Kozlowski
0 siblings, 1 reply; 10+ messages in thread
From: Hardevsinh Palaniya @ 2025-07-08 11:28 UTC (permalink / raw)
To: Krzysztof Kozlowski, sakari.ailus@linux.intel.com,
andriy.shevchenko@linux.intel.com, krzk+dt@kernel.org
Cc: Himanshu Bhavani, Mauro Carvalho Chehab, Rob Herring,
Conor Dooley, Hans Verkuil, André Apitzsch, Hans de Goede,
Ricardo Ribalda, Heimir Thor Sverrisson, Matthias Fend,
Benjamin Mugnier, Jingjing Xiong, Sylvain Petinot, Dongcheng Yan,
Arnd Bergmann, Bryan O'Donoghue, linux-media@vger.kernel.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org
> On 08/07/2025 12:25, Hardevsinh Palaniya wrote:
> > +
> > +static const struct v4l2_subdev_ops ov2735_subdev_ops = {
> > + .video = &ov2735_video_ops,
> > + .pad = &ov2735_pad_ops,
> > +};
> > +
> > +static const struct v4l2_subdev_internal_ops ov2735_internal_ops = {
> > + .init_state = ov2735_init_state,
> > +};
> > +
> > +static int ov2735_power_on(struct device *dev)
> > +{
> > + struct v4l2_subdev *sd = dev_get_drvdata(dev);
> > + struct ov2735 *ov2735 = to_ov2735(sd);
> > + unsigned long delay_us;
> > + int ret;
> > +
> > + gpiod_set_value_cansleep(ov2735->pwdn_gpio, 0);
>
> So you power up here...
>
> > + fsleep(3000);
> > +
> > + ret = regulator_bulk_enable(ARRAY_SIZE(ov2735_supply_name),
> > + ov2735->supplies);
> > + if (ret) {
> > + dev_err(ov2735->dev, "failed to enable regulators\n");
> > + return ret;
> > + }
> > +
> > + gpiod_set_value_cansleep(ov2735->pwdn_gpio, 1);
>
> And here you power down your device. This makes no sense... unless this
> is not a power down GPIO.
In Datasheet
Power-up sequence:
|--------------------------------------
avdd ----|
<-t1->
|--------------------------------
dovdd ---------|
<-T2->
|--------------------------
dvdd ------------------|
<-T3->
|---------------------|
pwdn -----| |-------------------
<-T4->
|-------------
rst ------------------------------------|
Best Regards,
Hardev
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH v2 2/2] media: i2c: add ov2735 image sensor driver
2025-07-08 10:25 ` [PATCH v2 2/2] media: i2c: add ov2735 image sensor driver Hardevsinh Palaniya
2025-07-08 10:42 ` Krzysztof Kozlowski
@ 2025-07-08 11:40 ` Kieran Bingham
2025-07-08 13:25 ` Dave Stevenson
2 siblings, 0 replies; 10+ messages in thread
From: Kieran Bingham @ 2025-07-08 11:40 UTC (permalink / raw)
To: Hardevsinh Palaniya, andriy.shevchenko, krzk+dt, sakari.ailus,
Pratap Nirujogi
Cc: Hardevsinh Palaniya, Himanshu Bhavani, Mauro Carvalho Chehab,
Rob Herring, Conor Dooley, Hans Verkuil, André Apitzsch,
Hans de Goede, Ricardo Ribalda, Heimir Thor Sverrisson,
Matthias Fend, Benjamin Mugnier, Jingjing Xiong, Sylvain Petinot,
Dongcheng Yan, Arnd Bergmann, Bryan O'Donoghue, linux-media,
devicetree, linux-kernel
Hi all,
It looks like we have a second potential user for some CCI Page helpers:
Hardevsinh,
Could you take a look at the work being done by Pratap please?
- https://lore.kernel.org/all/4402c585-5cc2-428c-be3f-5f08eb53e97a@amd.com/
Quoting Hardevsinh Palaniya (2025-07-08 11:25:56)
> Add a v4l2 subdevice driver for the Omnivision OV2735 sensor.
>
> The Omnivision OV2735 is a 1/2.7-Inch CMOS image sensor with an
> active array size of 1920 x 1080.
>
> The following features are supported:
> - Manual exposure an gain control support
> - vblank/hblank control support
> - Test pattern support control
> - Supported resolution: 1920 x 1080 @ 30fps (SGRBG10)
>
> Co-developed-by: Himanshu Bhavani <himanshu.bhavani@siliconsignals.io>
> Signed-off-by: Himanshu Bhavani <himanshu.bhavani@siliconsignals.io>
> Signed-off-by: Hardevsinh Palaniya <hardevsinh.palaniya@siliconsignals.io>
> ---
<snip>
> +
> +#define OV2735_XCLK_FREQ (24 * HZ_PER_MHZ)
> +
> +#define OV2735_REG_PAGE_SELECT CCI_REG8(0xfd)
> +
> +/* Page 0 */
> +#define OV2735_REG_CHIPID CCI_REG16(0x02)
> +#define OV2735_CHIPID 0x2735
> +
> +#define OV2735_REG_SOFT_REST CCI_REG8(0x20)
> +
> +/* Clock Settings */
> +#define OV2735_REG_PLL_CTRL CCI_REG8(0x2f)
> +#define OV2735_REG_PLL_OUTDIV CCI_REG8(0x34)
> +#define OV2735_REG_CLK_MODE CCI_REG8(0x30)
> +#define OV2735_REG_CLOCK_REG1 CCI_REG8(0x33)
> +#define OV2735_REG_CLOCK_REG2 CCI_REG8(0x35)
> +
> +/* Page 1 */
> +#define OV2735_REG_STREAM_CTRL CCI_REG8(0xa0)
> +#define OV2735_STREAM_ON 0x01
> +#define OV2735_STREAM_OFF 0x00
> +
> +#define OV2735_REG_UPDOWN_MIRROR CCI_REG8(0x3f)
> +#define OV2735_REG_BINNING_DAC_CODE_MODE CCI_REG8(0x30)
> +#define OV2735_REG_FRAME_LENGTH CCI_REG16(0x0e)
> +#define OV2735_VTS_MAX 0x0fff
> +#define OV2735_REG_FRAME_EXP_SEPERATE_EN CCI_REG8(0x0d)
> +#define OV2735_FRAME_EXP_SEPERATE_EN 0x10
> +#define OV2735_REG_FRAME_SYNC CCI_REG8(0x01)
> +
> +#define OV2735_REG_HBLANK CCI_REG16(0x09)
> +
> +#define OV2735_REG_HS_MIPI CCI_REG8(0xb1)
> +#define OV2735_REG_MIPI_CTRL1 CCI_REG8(0x92)
> +#define OV2735_REG_MIPI_CTRL2 CCI_REG8(0x94)
> +#define OV2735_REG_MIPI_CTRL3 CCI_REG8(0xa1)
> +#define OV2735_REG_MIPI_CTRL4 CCI_REG8(0xb2)
> +#define OV2735_REG_MIPI_CTRL5 CCI_REG8(0xb3)
> +#define OV2735_REG_MIPI_CTRL6 CCI_REG8(0xb4)
> +#define OV2735_REG_MIPI_CTRL7 CCI_REG8(0xb5)
> +#define OV2735_REG_PREPARE CCI_REG8(0x95)
> +#define OV2735_REG_R_HS_ZERO CCI_REG8(0x96)
> +#define OV2735_REG_TRAIL CCI_REG8(0x98)
> +#define OV2735_REG_R_CLK_ZERO CCI_REG8(0x9c)
> +#define OV2735_REG_MIPI_V_SIZE CCI_REG16(0x8e)
> +#define OV2735_REG_MIPI_H_SIZE CCI_REG16(0x90)
> +
> +#define OV2735_REG_ANALOG_CTRL3 CCI_REG8(0x25)
> +#define OV2735_REG_VNCP CCI_REG8(0x20)
> +
> +/* BLC registers */
> +#define OV2735_REG_BLC_GAIN_BLUE CCI_REG8(0x86)
> +#define OV2735_REG_BLC_GAIN_RED CCI_REG8(0x87)
> +#define OV2735_REG_BLC_GAIN_GR CCI_REG8(0x88)
> +#define OV2735_REG_BLC_GAIN_GB CCI_REG8(0x89)
> +#define OV2735_REG_GB_SUBOFFSET CCI_REG8(0xf0)
> +#define OV2735_REG_BLUE_SUBOFFSET CCI_REG8(0xf1)
> +#define OV2735_REG_RED_SUBOFFSET CCI_REG8(0xf2)
> +#define OV2735_REG_GR_SUBOFFSET CCI_REG8(0xf3)
> +#define OV2735_REG_BLC_BPC_TH_P CCI_REG8(0xfc)
> +#define OV2735_REG_BLC_BPC_TH_N CCI_REG8(0xfe)
> +
> +#define OV2735_REG_TEST_PATTERN CCI_REG8(0xb2)
> +#define OV2735_TEST_PATTERN_ENABLE 0x01
> +#define OV2735_TEST_PATTERN_DISABLE 0xfe
> +
> +#define OV2735_REG_LONG_EXPOSURE CCI_REG16(0x03)
> +#define OV2735_EXPOSURE_MIN 4
> +#define OV2735_EXPOSURE_STEP 1
> +
> +#define OV2735_REG_ANALOG_GAIN CCI_REG8(0x24)
> +#define OV2735_ANALOG_GAIN_MIN 0x10
> +#define OV2735_ANALOG_GAIN_MAX 0xff
> +#define OV2735_ANALOG_GAIN_STEP 1
> +#define OV2735_ANALOG_GAIN_DEFAULT 0x10
> +
> +/* Page 2 */
> +#define OV2735_REG_V_START CCI_REG16(0xa0)
> +#define OV2735_REG_V_SIZE CCI_REG16(0xa2)
> +#define OV2735_REG_H_START CCI_REG16(0xa4)
> +#define OV2735_REG_H_SIZE CCI_REG16(0xa6)
> +
> +#define OV2735_LINK_FREQ_420MHZ (420 * HZ_PER_MHZ)
> +#define OV2735_PIXEL_RATE (168 * HZ_PER_MHZ)
> +
<snip>
> +static struct cci_reg_sequence ov2735_1920_1080_30fps[] = {
> + { OV2735_REG_PAGE_SELECT, 0x00 },
> + { OV2735_REG_PLL_CTRL, 0x10 },
> + { OV2735_REG_PLL_OUTDIV, 0x00 },
> + { OV2735_REG_CLK_MODE, 0x15 },
> + { OV2735_REG_CLOCK_REG1, 0x01 },
> + { OV2735_REG_CLOCK_REG2, 0x20 },
> + { OV2735_REG_PAGE_SELECT, 0x01 },
> + { OV2735_REG_BINNING_DAC_CODE_MODE, 0x00 },
> + { CCI_REG8(0xfb), 0x73 },
> + { OV2735_REG_FRAME_SYNC, 0x01 },
> + { OV2735_REG_PAGE_SELECT, 0x01 },
> +
> + /* Timing ctrl */
> + { CCI_REG8(0x1a), 0x6b },
> + { CCI_REG8(0x1c), 0xea },
> + { CCI_REG8(0x16), 0x0c },
> + { CCI_REG8(0x21), 0x00 },
> + { CCI_REG8(0x11), 0x63 },
> + { CCI_REG8(0x19), 0xc3 },
> +
> + /* Analog ctrl */
> + { CCI_REG8(0x26), 0x5a },
> + { CCI_REG8(0x29), 0x01 },
> + { CCI_REG8(0x33), 0x6f },
> + { CCI_REG8(0x2a), 0xd2 },
> + { CCI_REG8(0x2c), 0x40 },
> + { CCI_REG8(0xd0), 0x02 },
> + { CCI_REG8(0xd1), 0x01 },
> + { CCI_REG8(0xd2), 0x20 },
> + { CCI_REG8(0xd3), 0x04 },
> + { CCI_REG8(0xd4), 0x2a },
> + { CCI_REG8(0x50), 0x00 },
> + { CCI_REG8(0x51), 0x2c },
> + { CCI_REG8(0x52), 0x29 },
> + { CCI_REG8(0x53), 0x00 },
> + { CCI_REG8(0x55), 0x44 },
> + { CCI_REG8(0x58), 0x29 },
> + { CCI_REG8(0x5a), 0x00 },
> + { CCI_REG8(0x5b), 0x00 },
> + { CCI_REG8(0x5d), 0x00 },
> + { CCI_REG8(0x64), 0x2f },
> + { CCI_REG8(0x66), 0x62 },
> + { CCI_REG8(0x68), 0x5b },
> + { CCI_REG8(0x75), 0x46 },
> + { CCI_REG8(0x76), 0x36 },
> + { CCI_REG8(0x77), 0x4f },
> + { CCI_REG8(0x78), 0xef },
> + { CCI_REG8(0x72), 0xcf },
> + { CCI_REG8(0x73), 0x36 },
> + { CCI_REG8(0x7d), 0x0d },
> + { CCI_REG8(0x7e), 0x0d },
> + { CCI_REG8(0x8a), 0x77 },
> + { CCI_REG8(0x8b), 0x77 },
> +
> + { OV2735_REG_PAGE_SELECT, 0x01 },
> + { OV2735_REG_HS_MIPI, 0x83 },
> + { OV2735_REG_MIPI_CTRL5, 0x0b },
> + { OV2735_REG_MIPI_CTRL6, 0x14 },
> + { CCI_REG8(0x9d), 0x40 },
> + { OV2735_REG_MIPI_CTRL3, 0x05 },
> + { OV2735_REG_MIPI_CTRL2, 0x44 },
> + { OV2735_REG_PREPARE, 0x33 },
> + { OV2735_REG_R_HS_ZERO, 0x1f },
> + { OV2735_REG_TRAIL, 0x45 },
> + { OV2735_REG_R_CLK_ZERO, 0x10 },
> + { OV2735_REG_MIPI_CTRL7, 0x70 },
> + { OV2735_REG_ANALOG_CTRL3, 0xe0 },
> + { OV2735_REG_VNCP, 0x7b },
> +
> + /* BLC */
> + { OV2735_REG_PAGE_SELECT, 0x01 },
> + { OV2735_REG_BLC_GAIN_BLUE, 0x77 },
> + { OV2735_REG_BLC_GAIN_GB, 0x77 },
> + { OV2735_REG_BLC_GAIN_RED, 0x74 },
> + { OV2735_REG_BLC_GAIN_GR, 0x74 },
> + { OV2735_REG_BLC_BPC_TH_P, 0xe0 },
> + { OV2735_REG_BLC_BPC_TH_N, 0xe0 },
> + { OV2735_REG_GB_SUBOFFSET, 0x40 },
> + { OV2735_REG_BLUE_SUBOFFSET, 0x40 },
> + { OV2735_REG_RED_SUBOFFSET, 0x40 },
> + { OV2735_REG_GR_SUBOFFSET, 0x40 },
> +
> + /* 1920x1080 */
> + { OV2735_REG_PAGE_SELECT, 0x02 },
> + { OV2735_REG_V_START, 0x0008 },
> + { OV2735_REG_V_SIZE, 0x0438 },
> + { OV2735_REG_H_START, 0x0008 },
> + { OV2735_REG_H_SIZE, 0x03c0 },
> + { OV2735_REG_PAGE_SELECT, 0x01 },
> + { OV2735_REG_MIPI_V_SIZE, 0x0780 },
> + { OV2735_REG_MIPI_H_SIZE, 0x0438 },
> +};
> +
<snip>
> +static int ov2735_enable_test_pattern(struct ov2735 *ov2735, u32 pattern)
> +{
> + int ret = 0;
> + u64 val;
> +
> + cci_read(ov2735->cci, OV2735_REG_TEST_PATTERN, &val, &ret);
> + if (ret)
> + return ret;
> +
> + switch (pattern) {
> + case 0:
> + val &= ~OV2735_TEST_PATTERN_ENABLE;
> + break;
> + case 1:
> + val |= OV2735_TEST_PATTERN_ENABLE;
> + break;
> + }
> +
> + return cci_write(ov2735->cci, OV2735_REG_TEST_PATTERN, val, NULL);
> +}
> +
> +static int ov2735_set_ctrl(struct v4l2_ctrl *ctrl)
> +{
> + struct ov2735 *ov2735 = container_of(ctrl->handler, struct ov2735,
> + handler);
> + const struct ov2735_mode *mode;
> + struct v4l2_mbus_framefmt *fmt;
> + struct v4l2_subdev_state *state;
> + u64 vts;
> + int ret = 0;
> +
> + state = v4l2_subdev_get_locked_active_state(&ov2735->sd);
> + fmt = v4l2_subdev_state_get_format(state, 0);
> +
> + mode = v4l2_find_nearest_size(supported_modes,
> + ARRAY_SIZE(supported_modes),
> + width, height,
> + fmt->width, fmt->height);
> +
> + if (ctrl->id == V4L2_CID_VBLANK) {
> + /* Honour the VBLANK limits when setting exposure. */
> + s64 max = mode->height + ctrl->val - 4;
> +
> + ret = __v4l2_ctrl_modify_range(ov2735->exposure,
> + ov2735->exposure->minimum, max,
> + ov2735->exposure->step,
> + ov2735->exposure->default_value);
> + if (ret)
> + return ret;
> + }
> +
> + /*
> + * Applying V4L2 control value only happens
> + * when power is up for streaming.
> + */
> + if (pm_runtime_get_if_in_use(ov2735->dev) == 0)
> + return 0;
> +
> + cci_write(ov2735->cci, OV2735_REG_PAGE_SELECT, 0x01, &ret);
> +
And this is a clear location (and the others though) that should use
helpers so that the writes below are contained correctly to the correct
page, and the page is only updated when it's changed.
> + switch (ctrl->id) {
> + case V4L2_CID_EXPOSURE:
> + cci_write(ov2735->cci, OV2735_REG_LONG_EXPOSURE, ctrl->val, &ret);
> + break;
> + case V4L2_CID_ANALOGUE_GAIN:
> + cci_write(ov2735->cci, OV2735_REG_ANALOG_GAIN, ctrl->val, &ret);
> + break;
> + case V4L2_CID_HBLANK:
> + cci_write(ov2735->cci, OV2735_REG_HBLANK, ctrl->val, &ret);
> + break;
> + case V4L2_CID_VBLANK:
> + vts = ctrl->val + mode->height;
> + cci_write(ov2735->cci, OV2735_REG_FRAME_EXP_SEPERATE_EN,
> + OV2735_FRAME_EXP_SEPERATE_EN, &ret);
> + cci_write(ov2735->cci, OV2735_REG_FRAME_LENGTH, vts, &ret);
> + break;
> + case V4L2_CID_TEST_PATTERN:
> + ret = ov2735_enable_test_pattern(ov2735, ctrl->val);
> + break;
> + default:
> + dev_err(ov2735->dev, "ctrl(id:0x%x, val:0x%x) is not handled\n",
> + ctrl->id, ctrl->val);
> + break;
> + }
> + cci_write(ov2735->cci, OV2735_REG_FRAME_SYNC, 0x01, &ret);
> +
> + pm_runtime_put(ov2735->dev);
> +
> + return ret;
> +}
<snip>
> +
> +static int ov2735_enable_streams(struct v4l2_subdev *sd,
> + struct v4l2_subdev_state *state, u32 pad,
> + u64 streams_mask)
> +{
> + struct ov2735 *ov2735 = to_ov2735(sd);
> + const struct ov2735_mode *mode;
> + const struct ov2735_reglist *reg_list;
> + const struct v4l2_mbus_framefmt *fmt;
> + int ret;
> +
> + fmt = v4l2_subdev_state_get_format(state, 0);
> + mode = v4l2_find_nearest_size(supported_modes,
> + ARRAY_SIZE(supported_modes),
> + width, height,
> + fmt->width, fmt->height);
> +
> + ret = pm_runtime_resume_and_get(ov2735->dev);
> + if (ret < 0)
> + return ret;
> +
> + reg_list = &mode->reg_list;
> + cci_multi_reg_write(ov2735->cci, reg_list->regvals, reg_list->num_regs, &ret);
> + if (ret) {
> + dev_err(ov2735->dev, "%s failed to send mfg header\n", __func__);
> + goto err_rpm_put;
> + }
> +
> + /* Apply customized values from user */
> + ret = __v4l2_ctrl_handler_setup(ov2735->sd.ctrl_handler);
> + if (ret)
> + goto err_rpm_put;
> +
> + /* set stream on register */
> + cci_write(ov2735->cci, OV2735_REG_PAGE_SELECT, 0x01, &ret);
> + cci_write(ov2735->cci, OV2735_REG_STREAM_CTRL, OV2735_STREAM_ON, &ret);
More page handling could be combined.
> + if (ret)
> + goto err_rpm_put;
> +
> + return 0;
> +
> +err_rpm_put:
> + pm_runtime_put(ov2735->dev);
> + return ret;
> +}
> +
<snip>
> +static int ov2735_identify_module(struct ov2735 *ov2735)
> +{
> + u64 chip_id;
> + int ret = 0;
> +
> + cci_write(ov2735->cci, OV2735_REG_PAGE_SELECT, 0x00, &ret);
> + cci_read(ov2735->cci, OV2735_REG_CHIPID, &chip_id, &ret);
> + if (ret)
> + return dev_err_probe(ov2735->dev, ret, "failed to read chip id %x\n",
> + OV2735_CHIPID);
> +
> + if (chip_id != OV2735_CHIPID)
> + return dev_err_probe(ov2735->dev, -EIO, "chip id mismatch: %x!=%llx\n",
> + OV2735_CHIPID, chip_id);
> +
> + return 0;
> +}
<snipped>
--
Kieran
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH v2 2/2] media: i2c: add ov2735 image sensor driver
2025-07-08 10:25 ` [PATCH v2 2/2] media: i2c: add ov2735 image sensor driver Hardevsinh Palaniya
2025-07-08 10:42 ` Krzysztof Kozlowski
2025-07-08 11:40 ` Kieran Bingham
@ 2025-07-08 13:25 ` Dave Stevenson
2 siblings, 0 replies; 10+ messages in thread
From: Dave Stevenson @ 2025-07-08 13:25 UTC (permalink / raw)
To: Hardevsinh Palaniya
Cc: sakari.ailus, andriy.shevchenko, krzk+dt, Himanshu Bhavani,
Mauro Carvalho Chehab, Rob Herring, Conor Dooley, Hans Verkuil,
André Apitzsch, Hans de Goede, Ricardo Ribalda,
Heimir Thor Sverrisson, Matthias Fend, Benjamin Mugnier,
Jingjing Xiong, Sylvain Petinot, Dongcheng Yan, Arnd Bergmann,
Bryan O'Donoghue, linux-media, devicetree, linux-kernel
Hi Hardevsinh
Only a very quick read through, but 2 things stand out.
On Tue, 8 Jul 2025 at 11:27, Hardevsinh Palaniya
<hardevsinh.palaniya@siliconsignals.io> wrote:
>
> Add a v4l2 subdevice driver for the Omnivision OV2735 sensor.
>
> The Omnivision OV2735 is a 1/2.7-Inch CMOS image sensor with an
> active array size of 1920 x 1080.
>
> The following features are supported:
> - Manual exposure an gain control support
> - vblank/hblank control support
> - Test pattern support control
> - Supported resolution: 1920 x 1080 @ 30fps (SGRBG10)
>
> Co-developed-by: Himanshu Bhavani <himanshu.bhavani@siliconsignals.io>
> Signed-off-by: Himanshu Bhavani <himanshu.bhavani@siliconsignals.io>
> Signed-off-by: Hardevsinh Palaniya <hardevsinh.palaniya@siliconsignals.io>
> ---
> MAINTAINERS | 9 +
> drivers/media/i2c/Kconfig | 10 +
> drivers/media/i2c/Makefile | 1 +
> drivers/media/i2c/ov2735.c | 908 +++++++++++++++++++++++++++++++++++++
> 4 files changed, 928 insertions(+)
> create mode 100644 drivers/media/i2c/ov2735.c
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 92e9d8c7708f..058bbfd9523b 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -18471,6 +18471,15 @@ T: git git://linuxtv.org/media.git
> F: Documentation/devicetree/bindings/media/i2c/ovti,ov2685.yaml
> F: drivers/media/i2c/ov2685.c
>
> +OMNIVISION OV2735 SENSOR DRIVER
> +M: Hardevsinh Palaniya <hardevsinh.palaniya@siliconsignals.io>
> +M: Himanshu Bhavani <himanshu.bhavani@siliconsignals.io>
> +L: linux-media@vger.kernel.org
> +S: Maintained
> +T: git git://linuxtv.org/media.git
> +F: Documentation/devicetree/bindings/media/i2c/ovti,ov2735.yaml
> +F: drivers/media/i2c/ov2735.c
> +
> OMNIVISION OV2740 SENSOR DRIVER
> M: Tianshu Qiu <tian.shu.qiu@intel.com>
> R: Sakari Ailus <sakari.ailus@linux.intel.com>
> diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
> index 4b4c199da6ea..9646eab1b177 100644
> --- a/drivers/media/i2c/Kconfig
> +++ b/drivers/media/i2c/Kconfig
> @@ -446,6 +446,16 @@ config VIDEO_OV2685
> To compile this driver as a module, choose M here: the
> module will be called ov2685.
>
> +config VIDEO_OV2735
> + tristate "OmniVision OV2735 sensor support"
> + select V4L2_CCI_I2C
> + help
> + This is a Video4Linux2 sensor driver for the Sony
> + OV2735 camera.
> +
> + To compile this driver as a module, choose M here: the
> + module will be called ov2735.
> +
> config VIDEO_OV2740
> tristate "OmniVision OV2740 sensor support"
> depends on ACPI || COMPILE_TEST
> diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
> index 5873d29433ee..1adb27743fa1 100644
> --- a/drivers/media/i2c/Makefile
> +++ b/drivers/media/i2c/Makefile
> @@ -93,6 +93,7 @@ obj-$(CONFIG_VIDEO_OV2640) += ov2640.o
> obj-$(CONFIG_VIDEO_OV2659) += ov2659.o
> obj-$(CONFIG_VIDEO_OV2680) += ov2680.o
> obj-$(CONFIG_VIDEO_OV2685) += ov2685.o
> +obj-$(CONFIG_VIDEO_OV2735) += ov2735.o
> obj-$(CONFIG_VIDEO_OV2740) += ov2740.o
> obj-$(CONFIG_VIDEO_OV4689) += ov4689.o
> obj-$(CONFIG_VIDEO_OV5640) += ov5640.o
> diff --git a/drivers/media/i2c/ov2735.c b/drivers/media/i2c/ov2735.c
> new file mode 100644
> index 000000000000..a7df516eaedc
> --- /dev/null
> +++ b/drivers/media/i2c/ov2735.c
> @@ -0,0 +1,908 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * V4L2 Support for the OV2735
> + *
> + * Copyright (C) 2025 Silicon Signals Pvt. Ltd.
> + *
> + * Based on Rockchip ov2735 Camera Driver
> + * Copyright (C) 2017 Fuzhou Rockchip Electronics Co., Ltd.
> + *
> + * Inspired from ov8858, imx219, imx283 camera drivers
> + */
> +
> +#include <linux/array_size.h>
> +#include <linux/clk.h>
> +#include <linux/container_of.h>
> +#include <linux/delay.h>
> +#include <linux/device/devres.h>
> +#include <linux/err.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/i2c.h>
> +#include <linux/module.h>
> +#include <linux/pm_runtime.h>
> +#include <linux/property.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/units.h>
> +#include <linux/types.h>
> +
> +#include <media/v4l2-cci.h>
> +#include <media/v4l2-ctrls.h>
> +#include <media/v4l2-device.h>
> +#include <media/v4l2-fwnode.h>
> +#include <media/v4l2-mediabus.h>
> +
> +#define OV2735_XCLK_FREQ (24 * HZ_PER_MHZ)
> +
> +#define OV2735_REG_PAGE_SELECT CCI_REG8(0xfd)
> +
> +/* Page 0 */
> +#define OV2735_REG_CHIPID CCI_REG16(0x02)
> +#define OV2735_CHIPID 0x2735
> +
> +#define OV2735_REG_SOFT_REST CCI_REG8(0x20)
> +
> +/* Clock Settings */
> +#define OV2735_REG_PLL_CTRL CCI_REG8(0x2f)
> +#define OV2735_REG_PLL_OUTDIV CCI_REG8(0x34)
> +#define OV2735_REG_CLK_MODE CCI_REG8(0x30)
> +#define OV2735_REG_CLOCK_REG1 CCI_REG8(0x33)
> +#define OV2735_REG_CLOCK_REG2 CCI_REG8(0x35)
> +
> +/* Page 1 */
> +#define OV2735_REG_STREAM_CTRL CCI_REG8(0xa0)
> +#define OV2735_STREAM_ON 0x01
> +#define OV2735_STREAM_OFF 0x00
> +
> +#define OV2735_REG_UPDOWN_MIRROR CCI_REG8(0x3f)
> +#define OV2735_REG_BINNING_DAC_CODE_MODE CCI_REG8(0x30)
> +#define OV2735_REG_FRAME_LENGTH CCI_REG16(0x0e)
> +#define OV2735_VTS_MAX 0x0fff
> +#define OV2735_REG_FRAME_EXP_SEPERATE_EN CCI_REG8(0x0d)
> +#define OV2735_FRAME_EXP_SEPERATE_EN 0x10
> +#define OV2735_REG_FRAME_SYNC CCI_REG8(0x01)
> +
> +#define OV2735_REG_HBLANK CCI_REG16(0x09)
> +
> +#define OV2735_REG_HS_MIPI CCI_REG8(0xb1)
> +#define OV2735_REG_MIPI_CTRL1 CCI_REG8(0x92)
> +#define OV2735_REG_MIPI_CTRL2 CCI_REG8(0x94)
> +#define OV2735_REG_MIPI_CTRL3 CCI_REG8(0xa1)
> +#define OV2735_REG_MIPI_CTRL4 CCI_REG8(0xb2)
> +#define OV2735_REG_MIPI_CTRL5 CCI_REG8(0xb3)
> +#define OV2735_REG_MIPI_CTRL6 CCI_REG8(0xb4)
> +#define OV2735_REG_MIPI_CTRL7 CCI_REG8(0xb5)
> +#define OV2735_REG_PREPARE CCI_REG8(0x95)
> +#define OV2735_REG_R_HS_ZERO CCI_REG8(0x96)
> +#define OV2735_REG_TRAIL CCI_REG8(0x98)
> +#define OV2735_REG_R_CLK_ZERO CCI_REG8(0x9c)
> +#define OV2735_REG_MIPI_V_SIZE CCI_REG16(0x8e)
> +#define OV2735_REG_MIPI_H_SIZE CCI_REG16(0x90)
> +
> +#define OV2735_REG_ANALOG_CTRL3 CCI_REG8(0x25)
> +#define OV2735_REG_VNCP CCI_REG8(0x20)
> +
> +/* BLC registers */
> +#define OV2735_REG_BLC_GAIN_BLUE CCI_REG8(0x86)
> +#define OV2735_REG_BLC_GAIN_RED CCI_REG8(0x87)
> +#define OV2735_REG_BLC_GAIN_GR CCI_REG8(0x88)
> +#define OV2735_REG_BLC_GAIN_GB CCI_REG8(0x89)
> +#define OV2735_REG_GB_SUBOFFSET CCI_REG8(0xf0)
> +#define OV2735_REG_BLUE_SUBOFFSET CCI_REG8(0xf1)
> +#define OV2735_REG_RED_SUBOFFSET CCI_REG8(0xf2)
> +#define OV2735_REG_GR_SUBOFFSET CCI_REG8(0xf3)
> +#define OV2735_REG_BLC_BPC_TH_P CCI_REG8(0xfc)
> +#define OV2735_REG_BLC_BPC_TH_N CCI_REG8(0xfe)
> +
> +#define OV2735_REG_TEST_PATTERN CCI_REG8(0xb2)
> +#define OV2735_TEST_PATTERN_ENABLE 0x01
> +#define OV2735_TEST_PATTERN_DISABLE 0xfe
> +
> +#define OV2735_REG_LONG_EXPOSURE CCI_REG16(0x03)
> +#define OV2735_EXPOSURE_MIN 4
> +#define OV2735_EXPOSURE_STEP 1
> +
> +#define OV2735_REG_ANALOG_GAIN CCI_REG8(0x24)
> +#define OV2735_ANALOG_GAIN_MIN 0x10
> +#define OV2735_ANALOG_GAIN_MAX 0xff
> +#define OV2735_ANALOG_GAIN_STEP 1
> +#define OV2735_ANALOG_GAIN_DEFAULT 0x10
> +
> +/* Page 2 */
> +#define OV2735_REG_V_START CCI_REG16(0xa0)
> +#define OV2735_REG_V_SIZE CCI_REG16(0xa2)
> +#define OV2735_REG_H_START CCI_REG16(0xa4)
> +#define OV2735_REG_H_SIZE CCI_REG16(0xa6)
> +
> +#define OV2735_LINK_FREQ_420MHZ (420 * HZ_PER_MHZ)
> +#define OV2735_PIXEL_RATE (168 * HZ_PER_MHZ)
> +
> +static const char * const ov2735_supply_name[] = {
> + "AVDD", /* Analog power */
> + "DOVDD", /* Digital I/O power */
> + "DVDD", /* Digital core power */
> +};
> +
> +struct ov2735 {
> + struct device *dev;
> + struct regmap *cci;
> + struct v4l2_subdev sd;
> + struct media_pad pad;
> + struct i2c_client *client;
> + struct clk *xclk;
> + struct gpio_desc *reset_gpio;
> + struct gpio_desc *pwdn_gpio;
> + struct regulator_bulk_data supplies[ARRAY_SIZE(ov2735_supply_name)];
> +
> + /* V4L2 Controls */
> + struct v4l2_ctrl_handler handler;
> + struct v4l2_ctrl *link_freq;
> + struct v4l2_ctrl *pixel_rate;
> + struct v4l2_ctrl *hblank;
> + struct v4l2_ctrl *vblank;
> + struct v4l2_ctrl *gain;
> + struct v4l2_ctrl *exposure;
> + struct v4l2_ctrl *test_pattern;
> +};
> +
> +struct ov2735_reglist {
> + unsigned int num_regs;
> + const struct cci_reg_sequence *regvals;
> +};
> +
> +struct ov2735_mode {
> + u32 width;
> + u32 height;
> + u32 hts_def;
> + u32 vts_def;
> + u32 exp_def;
> + struct ov2735_reglist reg_list;
> +};
> +
> +static struct cci_reg_sequence ov2735_1920_1080_30fps[] = {
> + { OV2735_REG_PAGE_SELECT, 0x00 },
> + { OV2735_REG_PLL_CTRL, 0x10 },
> + { OV2735_REG_PLL_OUTDIV, 0x00 },
> + { OV2735_REG_CLK_MODE, 0x15 },
> + { OV2735_REG_CLOCK_REG1, 0x01 },
> + { OV2735_REG_CLOCK_REG2, 0x20 },
> + { OV2735_REG_PAGE_SELECT, 0x01 },
> + { OV2735_REG_BINNING_DAC_CODE_MODE, 0x00 },
> + { CCI_REG8(0xfb), 0x73 },
> + { OV2735_REG_FRAME_SYNC, 0x01 },
> + { OV2735_REG_PAGE_SELECT, 0x01 },
> +
> + /* Timing ctrl */
> + { CCI_REG8(0x1a), 0x6b },
> + { CCI_REG8(0x1c), 0xea },
> + { CCI_REG8(0x16), 0x0c },
> + { CCI_REG8(0x21), 0x00 },
> + { CCI_REG8(0x11), 0x63 },
> + { CCI_REG8(0x19), 0xc3 },
> +
> + /* Analog ctrl */
> + { CCI_REG8(0x26), 0x5a },
> + { CCI_REG8(0x29), 0x01 },
> + { CCI_REG8(0x33), 0x6f },
> + { CCI_REG8(0x2a), 0xd2 },
> + { CCI_REG8(0x2c), 0x40 },
> + { CCI_REG8(0xd0), 0x02 },
> + { CCI_REG8(0xd1), 0x01 },
> + { CCI_REG8(0xd2), 0x20 },
> + { CCI_REG8(0xd3), 0x04 },
> + { CCI_REG8(0xd4), 0x2a },
> + { CCI_REG8(0x50), 0x00 },
> + { CCI_REG8(0x51), 0x2c },
> + { CCI_REG8(0x52), 0x29 },
> + { CCI_REG8(0x53), 0x00 },
> + { CCI_REG8(0x55), 0x44 },
> + { CCI_REG8(0x58), 0x29 },
> + { CCI_REG8(0x5a), 0x00 },
> + { CCI_REG8(0x5b), 0x00 },
> + { CCI_REG8(0x5d), 0x00 },
> + { CCI_REG8(0x64), 0x2f },
> + { CCI_REG8(0x66), 0x62 },
> + { CCI_REG8(0x68), 0x5b },
> + { CCI_REG8(0x75), 0x46 },
> + { CCI_REG8(0x76), 0x36 },
> + { CCI_REG8(0x77), 0x4f },
> + { CCI_REG8(0x78), 0xef },
> + { CCI_REG8(0x72), 0xcf },
> + { CCI_REG8(0x73), 0x36 },
> + { CCI_REG8(0x7d), 0x0d },
> + { CCI_REG8(0x7e), 0x0d },
> + { CCI_REG8(0x8a), 0x77 },
> + { CCI_REG8(0x8b), 0x77 },
> +
> + { OV2735_REG_PAGE_SELECT, 0x01 },
> + { OV2735_REG_HS_MIPI, 0x83 },
> + { OV2735_REG_MIPI_CTRL5, 0x0b },
> + { OV2735_REG_MIPI_CTRL6, 0x14 },
> + { CCI_REG8(0x9d), 0x40 },
> + { OV2735_REG_MIPI_CTRL3, 0x05 },
> + { OV2735_REG_MIPI_CTRL2, 0x44 },
> + { OV2735_REG_PREPARE, 0x33 },
> + { OV2735_REG_R_HS_ZERO, 0x1f },
> + { OV2735_REG_TRAIL, 0x45 },
> + { OV2735_REG_R_CLK_ZERO, 0x10 },
> + { OV2735_REG_MIPI_CTRL7, 0x70 },
> + { OV2735_REG_ANALOG_CTRL3, 0xe0 },
> + { OV2735_REG_VNCP, 0x7b },
> +
> + /* BLC */
> + { OV2735_REG_PAGE_SELECT, 0x01 },
> + { OV2735_REG_BLC_GAIN_BLUE, 0x77 },
> + { OV2735_REG_BLC_GAIN_GB, 0x77 },
> + { OV2735_REG_BLC_GAIN_RED, 0x74 },
> + { OV2735_REG_BLC_GAIN_GR, 0x74 },
> + { OV2735_REG_BLC_BPC_TH_P, 0xe0 },
> + { OV2735_REG_BLC_BPC_TH_N, 0xe0 },
> + { OV2735_REG_GB_SUBOFFSET, 0x40 },
> + { OV2735_REG_BLUE_SUBOFFSET, 0x40 },
> + { OV2735_REG_RED_SUBOFFSET, 0x40 },
> + { OV2735_REG_GR_SUBOFFSET, 0x40 },
> +
> + /* 1920x1080 */
> + { OV2735_REG_PAGE_SELECT, 0x02 },
> + { OV2735_REG_V_START, 0x0008 },
> + { OV2735_REG_V_SIZE, 0x0438 },
> + { OV2735_REG_H_START, 0x0008 },
> + { OV2735_REG_H_SIZE, 0x03c0 },
> + { OV2735_REG_PAGE_SELECT, 0x01 },
> + { OV2735_REG_MIPI_V_SIZE, 0x0780 },
> + { OV2735_REG_MIPI_H_SIZE, 0x0438 },
> +};
> +
> +static const struct ov2735_mode supported_modes[] = {
> + {
> + .width = 1920,
> + .height = 1080,
> + .exp_def = 399,
> + .hts_def = 2200,
> + .vts_def = 2545,
> + .reg_list = {
> + .num_regs = ARRAY_SIZE(ov2735_1920_1080_30fps),
> + .regvals = ov2735_1920_1080_30fps,
> + },
> + },
> +};
> +
> +static const s64 link_freq_menu_items[] = {
> + OV2735_LINK_FREQ_420MHZ,
> +};
> +
> +static const char * const ov2735_test_pattern_menu[] = {
> + "Disabled",
> + "Vertical Color",
> +};
> +
> +static const u32 ov2735_mbus_codes[] = {
> + MEDIA_BUS_FMT_SGRBG10_1X10,
> +};
This is only used in ov2735_enum_mbus_code, but the code is hard coded
in ov2735_enum_frame_size and ov2735_init_state. Making it consistent
would be nice.
> +
> +static inline struct ov2735 *to_ov2735(struct v4l2_subdev *_sd)
> +{
> + return container_of(_sd, struct ov2735, sd);
> +}
> +
> +static int ov2735_enable_test_pattern(struct ov2735 *ov2735, u32 pattern)
> +{
> + int ret = 0;
> + u64 val;
> +
> + cci_read(ov2735->cci, OV2735_REG_TEST_PATTERN, &val, &ret);
> + if (ret)
> + return ret;
> +
> + switch (pattern) {
> + case 0:
> + val &= ~OV2735_TEST_PATTERN_ENABLE;
> + break;
> + case 1:
> + val |= OV2735_TEST_PATTERN_ENABLE;
> + break;
> + }
> +
> + return cci_write(ov2735->cci, OV2735_REG_TEST_PATTERN, val, NULL);
> +}
> +
> +static int ov2735_set_ctrl(struct v4l2_ctrl *ctrl)
> +{
> + struct ov2735 *ov2735 = container_of(ctrl->handler, struct ov2735,
> + handler);
> + const struct ov2735_mode *mode;
> + struct v4l2_mbus_framefmt *fmt;
> + struct v4l2_subdev_state *state;
> + u64 vts;
> + int ret = 0;
> +
> + state = v4l2_subdev_get_locked_active_state(&ov2735->sd);
> + fmt = v4l2_subdev_state_get_format(state, 0);
> +
> + mode = v4l2_find_nearest_size(supported_modes,
> + ARRAY_SIZE(supported_modes),
> + width, height,
> + fmt->width, fmt->height);
> +
> + if (ctrl->id == V4L2_CID_VBLANK) {
> + /* Honour the VBLANK limits when setting exposure. */
> + s64 max = mode->height + ctrl->val - 4;
> +
> + ret = __v4l2_ctrl_modify_range(ov2735->exposure,
> + ov2735->exposure->minimum, max,
> + ov2735->exposure->step,
> + ov2735->exposure->default_value);
> + if (ret)
> + return ret;
> + }
> +
> + /*
> + * Applying V4L2 control value only happens
> + * when power is up for streaming.
> + */
> + if (pm_runtime_get_if_in_use(ov2735->dev) == 0)
> + return 0;
> +
> + cci_write(ov2735->cci, OV2735_REG_PAGE_SELECT, 0x01, &ret);
> +
> + switch (ctrl->id) {
> + case V4L2_CID_EXPOSURE:
> + cci_write(ov2735->cci, OV2735_REG_LONG_EXPOSURE, ctrl->val, &ret);
> + break;
> + case V4L2_CID_ANALOGUE_GAIN:
> + cci_write(ov2735->cci, OV2735_REG_ANALOG_GAIN, ctrl->val, &ret);
> + break;
> + case V4L2_CID_HBLANK:
> + cci_write(ov2735->cci, OV2735_REG_HBLANK, ctrl->val, &ret);
> + break;
> + case V4L2_CID_VBLANK:
> + vts = ctrl->val + mode->height;
> + cci_write(ov2735->cci, OV2735_REG_FRAME_EXP_SEPERATE_EN,
> + OV2735_FRAME_EXP_SEPERATE_EN, &ret);
> + cci_write(ov2735->cci, OV2735_REG_FRAME_LENGTH, vts, &ret);
> + break;
> + case V4L2_CID_TEST_PATTERN:
> + ret = ov2735_enable_test_pattern(ov2735, ctrl->val);
> + break;
> + default:
> + dev_err(ov2735->dev, "ctrl(id:0x%x, val:0x%x) is not handled\n",
> + ctrl->id, ctrl->val);
> + break;
> + }
> + cci_write(ov2735->cci, OV2735_REG_FRAME_SYNC, 0x01, &ret);
> +
> + pm_runtime_put(ov2735->dev);
> +
> + return ret;
> +}
> +
> +static const struct v4l2_ctrl_ops ov2735_ctrl_ops = {
> + .s_ctrl = ov2735_set_ctrl,
> +};
> +
> +static int ov2735_init_controls(struct ov2735 *ov2735)
> +{
> + struct v4l2_ctrl_handler *ctrl_hdlr;
> + struct v4l2_fwnode_device_properties props;
> + const struct ov2735_mode *mode = &supported_modes[0];
> + u64 hblank_def, vblank_def, exp_max;
> + int ret;
> +
> + ctrl_hdlr = &ov2735->handler;
> + ret = v4l2_ctrl_handler_init(ctrl_hdlr, 7);
You initialise 7 controls here, but also call
v4l2_ctrl_new_fwnode_properties which adds 2 additional ones, so this
should be 9.
Dave
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH v2 2/2] media: i2c: add ov2735 image sensor driver
2025-07-08 11:28 ` Hardevsinh Palaniya
@ 2025-07-08 13:26 ` Krzysztof Kozlowski
0 siblings, 0 replies; 10+ messages in thread
From: Krzysztof Kozlowski @ 2025-07-08 13:26 UTC (permalink / raw)
To: Hardevsinh Palaniya, sakari.ailus@linux.intel.com,
andriy.shevchenko@linux.intel.com, krzk+dt@kernel.org
Cc: Himanshu Bhavani, Mauro Carvalho Chehab, Rob Herring,
Conor Dooley, Hans Verkuil, André Apitzsch, Hans de Goede,
Ricardo Ribalda, Heimir Thor Sverrisson, Matthias Fend,
Benjamin Mugnier, Jingjing Xiong, Sylvain Petinot, Dongcheng Yan,
Arnd Bergmann, Bryan O'Donoghue, linux-media@vger.kernel.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org
On 08/07/2025 13:28, Hardevsinh Palaniya wrote:
>> On 08/07/2025 12:25, Hardevsinh Palaniya wrote:
>>> +
>>> +static const struct v4l2_subdev_ops ov2735_subdev_ops = {
>>> + .video = &ov2735_video_ops,
>>> + .pad = &ov2735_pad_ops,
>>> +};
>>> +
>>> +static const struct v4l2_subdev_internal_ops ov2735_internal_ops = {
>>> + .init_state = ov2735_init_state,
>>> +};
>>> +
>>> +static int ov2735_power_on(struct device *dev)
>>> +{
>>> + struct v4l2_subdev *sd = dev_get_drvdata(dev);
>>> + struct ov2735 *ov2735 = to_ov2735(sd);
>>> + unsigned long delay_us;
>>> + int ret;
>>> +
>>> + gpiod_set_value_cansleep(ov2735->pwdn_gpio, 0);
>>
>> So you power up here...
>>
>>> + fsleep(3000);
>>> +
>>> + ret = regulator_bulk_enable(ARRAY_SIZE(ov2735_supply_name),
>>> + ov2735->supplies);
>>> + if (ret) {
>>> + dev_err(ov2735->dev, "failed to enable regulators\n");
>>> + return ret;
>>> + }
>>> +
>>> + gpiod_set_value_cansleep(ov2735->pwdn_gpio, 1);
>>
>> And here you power down your device. This makes no sense... unless this
>> is not a power down GPIO.
>
> In Datasheet
> Power-up sequence:
>
> |--------------------------------------
> avdd ----|
> <-t1->
> |--------------------------------
> dovdd ---------|
> <-T2->
> |--------------------------
> dvdd ------------------|
> <-T3->
> |---------------------|
> pwdn -----| |-------------------
So that is not really a typical power down pin and this should be
explained clearly in property description. It rather feels like power-on
pin, which you need to pull for some time to boot the process and later
the supplies are keeping it on.
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH v2 1/2] dt-bindings: media: i2c: Add ov2735 sensor
2025-07-08 10:41 ` Krzysztof Kozlowski
@ 2025-07-10 7:18 ` Hardevsinh Palaniya
0 siblings, 0 replies; 10+ messages in thread
From: Hardevsinh Palaniya @ 2025-07-10 7:18 UTC (permalink / raw)
To: Krzysztof Kozlowski, sakari.ailus@linux.intel.com,
andriy.shevchenko@linux.intel.com, krzk+dt@kernel.org
Cc: Himanshu Bhavani, Mauro Carvalho Chehab, Rob Herring,
Conor Dooley, Hans Verkuil, Ricardo Ribalda, André Apitzsch,
Hans de Goede, Sylvain Petinot, Jingjing Xiong, Benjamin Mugnier,
Dongcheng Yan, Heimir Thor Sverrisson, Matthias Fend,
Arnd Bergmann, Bryan O'Donoghue, You-Sheng Yang,
linux-media@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
> On 08/07/2025 12:25, Hardevsinh Palaniya wrote:
> > +
> > + clocks:
> > + items:
> > + - description: XVCLK clock
> > +
> > + clock-names:
> > + items:
> > + - const: xvclk
> > +
> > + AVDD-supply:
>
> Use lowercase everywhere.
>
> > + description: Analog Domain Power Supply
> > +
> > + DOVDD-supply:
> > + description: I/O Domain Power Supply
> > +
> > + DVDD-supply:
> > + description: Digital Domain Power Supply
> > +
> > + reset-gpios:
> > + maxItems: 1
> > + description: Reset Pin GPIO Control (active low)
> > +
> > + pwdn-gpios:
>
> Use instead recommended name from the gpio-consumer-common.yaml.
As you mentioned in patch 2/2, this pin is not a typical power-down control
but behaves more like a power-on pin Based on this, I think enable-gpios
from gpio-consumer-common.yaml is a suitable choice here.
I will use enable-gpios and add a clear description for its usage in the binding.
Please let me know if you would still prefer poweron-gpios. In that case,
do I need to add poweron-gpios to the gpio-consumer-common.yaml file?
Best Regards,
Hardev
^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2025-07-10 7:19 UTC | newest]
Thread overview: 10+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2025-07-08 10:25 [PATCH v2 0/2] media: i2c: Add ov2735 camera sensor driver Hardevsinh Palaniya
2025-07-08 10:25 ` [PATCH v2 1/2] dt-bindings: media: i2c: Add ov2735 sensor Hardevsinh Palaniya
2025-07-08 10:41 ` Krzysztof Kozlowski
2025-07-10 7:18 ` Hardevsinh Palaniya
2025-07-08 10:25 ` [PATCH v2 2/2] media: i2c: add ov2735 image sensor driver Hardevsinh Palaniya
2025-07-08 10:42 ` Krzysztof Kozlowski
2025-07-08 11:28 ` Hardevsinh Palaniya
2025-07-08 13:26 ` Krzysztof Kozlowski
2025-07-08 11:40 ` Kieran Bingham
2025-07-08 13:25 ` Dave Stevenson
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).