[PATCH v8 0/2] media: i2c: Add ov2735 camera sensor driver

[PATCH v8 0/2] media: i2c: Add ov2735 camera sensor driver

[Hardevsinh Palaniya]

The Omnivision OV2735 is a 1/2.7-Inch CMOS image sensor with an                 
active array size of 1920 x 1080.                                               
                                                                                
The following features are supported:                                           
- Manual exposure an gain control support.                                      
- vblank/hblank control support.                                                
- Test pattern support control.                                                 
- Supported resolution: 1920 x 1080 @ 30fps (SGRBG10).                          
                                                                                
The driver is tested on mainline branch v6.14-rc6 on IMX8MP Debix Model a.      

v7 -> v8

In Patch 2/2:
- Correct some macro prefixes
- Add register names for timing and analog control registers
- Make the common register array const
- Wrap lines within 80 columns
- Remove unnecessary guard delay
                                                                                
v6 -> v7                                                                        
                                                                                
In Patch 1/2:                                                                   
- Remove 'link-frequencies' property (already present)                          
                                                                                
In Patch 2/2:                                                                   
- Add mutex guard                                                               
- Correct pll_ctrl_enable macro name                                            
- Add error check for '__v4l2_ctrl_modify_range'                                
- Remove unnecessary comments                                                   
                                                                                
v5 -> v6                                                                        
                                                                                
In Patch 1/2:                                                                   
- Add MAINTAINERS entry                                                         
                                                                                
In Patch 2/2:                                                                   
- Add Required headers                                                          
- Change ov2735_page_access prototype to remove casting                         
- Add error check for devm_pm_runtime*                                          
- Remove unused variable from stream_enable (Media CI robot detected)           
                                                                                
v4 -> v5                                                                        
                                                                                
In Patch 1/2:                                                                   
- Add Krzysztof's Review tag.                                                   
                                                                                
In Patch 2/2:                                                                   
- Remove redundant if (ret && err) check in ov2735_page_access()                
- Address coding style issues (indentation, format specifier, combined declaration)
- Replace hardcoded values with USEC_PER_MSEC where appropriate                 
- removing unused "ov2735->client = client"                                     
                                                                                
v3 -> v4                                                                        
                                                                                
In Patch 1/2:                                                                   
- Removed the clock-names property from the device tree binding.                
- Added link-frequencies property to the port node.                             
- Cleaned up the example by removing unnecessary entries.                       
                                                                                
In Patch 2/2:                                                                   
- Removed the cci_ prefix from read/write functions and custom page macros.     
- Corrected error handling in the ov2735_page_access() function.                
- Calculated PLL parameters dynamically based on the specified link frequency.  
- Set resolution registers from format and crop instead of hardcoding.          
- Fixed a memory leak in ov2735_parse_endpoint().                               
- Switched to devm_pm_runtime_*() functions for runtime PM handling.            
- Added documentation for the use of msleep() in the power_on() function.       
- Corrected GPIO polarity handling in the power_off() function.                 
                                                                                
v2 -> v3                                                                        
                                                                                
In Patch 1/2:                                                                   
- Renamed pwdn pin to enable pin.                                               
- Changed supply names to lowercase and added them to required properties.      
                                                                                
In Patch 2/2:                                                                   
- Stored page number in CCI private bits.                                       
- Added helper functions to handle page switching in cci_read() and cci_write().
- Removed ov2735_mbus_codes.                                                    
- Corrected control count to 9.                                                 
                                                                                
v1 -> v2                                                                        
                                                                                
- Added necessary header files.                                                 
- Corrected indentation.                                                        
- Used the ret parameter in cci_write and cci_read functions.                   

Hardevsinh Palaniya (1):
  media: i2c: add ov2735 image sensor driver

Himanshu Bhavani (1):
  dt-bindings: media: i2c: Add ov2735 sensor

 .../bindings/media/i2c/ovti,ov2735.yaml       |  108 ++
 MAINTAINERS                                   |    9 +
 drivers/media/i2c/Kconfig                     |   10 +
 drivers/media/i2c/Makefile                    |    1 +
 drivers/media/i2c/ov2735.c                    | 1109 +++++++++++++++++
 5 files changed, 1237 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/i2c/ovti,ov2735.yaml
 create mode 100644 drivers/media/i2c/ov2735.c

-- 
2.34.1

[PATCH v8 1/2] dt-bindings: media: i2c: Add ov2735 sensor

[Hardevsinh Palaniya]

From: Himanshu Bhavani <himanshu.bhavani@siliconsignals.io>

Add bindings for Omnivision OV2735 sensor.

Add MAINTAINERS entry for Omnivision OV2735 binding documentation

Signed-off-by: Himanshu Bhavani <himanshu.bhavani@siliconsignals.io>
Signed-off-by: Hardevsinh Palaniya <hardevsinh.palaniya@siliconsignals.io>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../bindings/media/i2c/ovti,ov2735.yaml       | 108 ++++++++++++++++++
 MAINTAINERS                                   |   8 ++
 2 files changed, 116 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/i2c/ovti,ov2735.yaml

diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov2735.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov2735.yaml
new file mode 100644
index 000000000000..bb34f21519c8
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov2735.yaml
@@ -0,0 +1,108 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/ovti,ov2735.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: OmniVision OV2735 Image Sensor
+
+maintainers:
+  - Himanshu Bhavani <himanshu.bhavani@siliconsignals.io>
+
+description:
+  The OmniVision OV2735 is a 2MP (1920x1080) color CMOS image sensor controlled
+  through an I2C-compatible SCCB bus. it outputs RAW10 format and uses a 1/2.7"
+  optical format.
+
+properties:
+  compatible:
+    const: ovti,ov2735
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: XVCLK clock
+
+  avdd-supply:
+    description: Analog Domain Power Supply
+
+  dovdd-supply:
+    description: I/O Domain Power Supply
+
+  dvdd-supply:
+    description: Digital Domain Power Supply
+
+  reset-gpios:
+    maxItems: 1
+    description: Reset Pin GPIO Control (active low)
+
+  enable-gpios:
+    maxItems: 1
+    description:
+      Active-low enable pin. Labeled as 'PWDN' in the datasheet, but acts as
+      an enable signal. During power rail ramp-up, the device remains powered
+      down. Once power rails are stable, pulling this pin low powers on the
+      device.
+
+  port:
+    description: MIPI CSI-2 transmitter port
+    $ref: /schemas/graph.yaml#/$defs/port-base
+    additionalProperties: false
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml#
+        unevaluatedProperties: false
+
+        properties:
+          data-lanes:
+            items:
+              - const: 1
+              - const: 2
+
+        required:
+          - data-lanes
+          - link-frequencies
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - avdd-supply
+  - dovdd-supply
+  - dvdd-supply
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        camera-sensor@3c {
+            compatible = "ovti,ov2735";
+            reg = <0x3c>;
+            clocks = <&ov2735_clk>;
+
+            avdd-supply = <&ov2735_avdd>;
+            dovdd-supply = <&ov2735_dovdd>;
+            dvdd-supply = <&ov2735_dvdd>;
+
+            reset-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+            enable-gpios = <&gpio2 11 GPIO_ACTIVE_LOW>;
+
+            port {
+                cam_out: endpoint {
+                    remote-endpoint = <&mipi_in_cam>;
+                    data-lanes = <1 2>;
+                    link-frequencies = /bits/ 64 <420000000>;
+                };
+            };
+        };
+    };
diff --git a/MAINTAINERS b/MAINTAINERS
index 92e9d8c7708f..474eefbd1363 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -18471,6 +18471,14 @@ T:	git git://linuxtv.org/media.git
 F:	Documentation/devicetree/bindings/media/i2c/ovti,ov2685.yaml
 F:	drivers/media/i2c/ov2685.c
 
+OMNIVISION OV2735 SENSOR DRIVER
+M:	Hardevsinh Palaniya <hardevsinh.palaniya@siliconsignals.io>
+M:	Himanshu Bhavani <himanshu.bhavani@siliconsignals.io>
+L:	linux-media@vger.kernel.org
+S:	Maintained
+T:	git git://linuxtv.org/media.git
+F:	Documentation/devicetree/bindings/media/i2c/ovti,ov2735.yaml
+
 OMNIVISION OV2740 SENSOR DRIVER
 M:	Tianshu Qiu <tian.shu.qiu@intel.com>
 R:	Sakari Ailus <sakari.ailus@linux.intel.com>
-- 
2.34.1

[PATCH v8 2/2] media: i2c: add ov2735 image sensor driver

[Hardevsinh Palaniya]

Add a v4l2 subdevice driver for the Omnivision OV2735 sensor.

The Omnivision OV2735 is a 1/2.7-Inch CMOS image sensor with an
active array size of 1920 x 1080.

The following features are supported:
- Manual exposure an gain control support
- vblank/hblank control support
- Test pattern support control
- Supported resolution: 1920 x 1080 @ 30fps (SGRBG10)

Co-developed-by: Himanshu Bhavani <himanshu.bhavani@siliconsignals.io>
Signed-off-by: Himanshu Bhavani <himanshu.bhavani@siliconsignals.io>
Signed-off-by: Hardevsinh Palaniya <hardevsinh.palaniya@siliconsignals.io>
---
 MAINTAINERS                |    1 +
 drivers/media/i2c/Kconfig  |   10 +
 drivers/media/i2c/Makefile |    1 +
 drivers/media/i2c/ov2735.c | 1109 ++++++++++++++++++++++++++++++++++++
 4 files changed, 1121 insertions(+)
 create mode 100644 drivers/media/i2c/ov2735.c

diff --git a/MAINTAINERS b/MAINTAINERS
index 474eefbd1363..058bbfd9523b 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -18478,6 +18478,7 @@ L:	linux-media@vger.kernel.org
 S:	Maintained
 T:	git git://linuxtv.org/media.git
 F:	Documentation/devicetree/bindings/media/i2c/ovti,ov2735.yaml
+F:	drivers/media/i2c/ov2735.c
 
 OMNIVISION OV2740 SENSOR DRIVER
 M:	Tianshu Qiu <tian.shu.qiu@intel.com>
diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
index 4b4c199da6ea..9646eab1b177 100644
--- a/drivers/media/i2c/Kconfig
+++ b/drivers/media/i2c/Kconfig
@@ -446,6 +446,16 @@ config VIDEO_OV2685
 	  To compile this driver as a module, choose M here: the
 	  module will be called ov2685.
 
+config VIDEO_OV2735
+	tristate "OmniVision OV2735 sensor support"
+	select V4L2_CCI_I2C
+	help
+	  This is a Video4Linux2 sensor driver for the Sony
+	  OV2735 camera.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called ov2735.
+
 config VIDEO_OV2740
 	tristate "OmniVision OV2740 sensor support"
 	depends on ACPI || COMPILE_TEST
diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
index 5873d29433ee..1adb27743fa1 100644
--- a/drivers/media/i2c/Makefile
+++ b/drivers/media/i2c/Makefile
@@ -93,6 +93,7 @@ obj-$(CONFIG_VIDEO_OV2640) += ov2640.o
 obj-$(CONFIG_VIDEO_OV2659) += ov2659.o
 obj-$(CONFIG_VIDEO_OV2680) += ov2680.o
 obj-$(CONFIG_VIDEO_OV2685) += ov2685.o
+obj-$(CONFIG_VIDEO_OV2735) += ov2735.o
 obj-$(CONFIG_VIDEO_OV2740) += ov2740.o
 obj-$(CONFIG_VIDEO_OV4689) += ov4689.o
 obj-$(CONFIG_VIDEO_OV5640) += ov5640.o
diff --git a/drivers/media/i2c/ov2735.c b/drivers/media/i2c/ov2735.c
new file mode 100644
index 000000000000..955c03bab1a4
--- /dev/null
+++ b/drivers/media/i2c/ov2735.c
@@ -0,0 +1,1109 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * V4L2 Support for the OV2735
+ *
+ * Copyright (C) 2025 Silicon Signals Pvt. Ltd.
+ *
+ * Based on Rockchip ov2735 Camera Driver
+ * Copyright (C) 2017 Fuzhou Rockchip Electronics Co., Ltd.
+ *
+ * Inspired from ov8858, imx219, imx283 camera drivers.
+ */
+
+#include <linux/array_size.h>
+#include <linux/bitops.h>
+#include <linux/cleanup.h>
+#include <linux/clk.h>
+#include <linux/container_of.h>
+#include <linux/delay.h>
+#include <linux/device/devres.h>
+#include <linux/err.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/pm_runtime.h>
+#include <linux/property.h>
+#include <linux/regulator/consumer.h>
+#include <linux/units.h>
+#include <linux/types.h>
+#include <linux/time.h>
+
+#include <media/v4l2-cci.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-fwnode.h>
+#include <media/v4l2-mediabus.h>
+
+#define OV2735_XCLK_FREQ			(24 * HZ_PER_MHZ)
+
+/* Add page number in CCI private bits [31:28] of the register address */
+#define OV2735_PAGE_REG8(p, x)	(((p) << CCI_REG_PRIVATE_SHIFT) | CCI_REG8(x))
+#define OV2735_PAGE_REG16(p, x)	(((p) << CCI_REG_PRIVATE_SHIFT) | CCI_REG16(x))
+
+#define OV2735_REG_PAGE_SELECT			CCI_REG8(0xfd)
+
+/* Page 0 */
+#define OV2735_REG_CHIPID			OV2735_PAGE_REG16(0x00, 0x02)
+#define OV2735_CHIPID				0x2735
+
+#define OV2735_REG_SOFT_RESET			OV2735_PAGE_REG8(0x00, 0x20)
+
+/* Clock Settings */
+#define OV2735_REG_PLL_CTRL			OV2735_PAGE_REG8(0x00, 0x2f)
+#define OV2735_PLL_CTRL_ENABLE			0x7f
+#define OV2735_REG_PLL_OUTDIV			OV2735_PAGE_REG8(0x00, 0x34)
+#define OV2735_REG_CLK_MODE			OV2735_PAGE_REG8(0x00, 0x30)
+#define OV2735_REG_CLOCK_REG1			OV2735_PAGE_REG8(0x00, 0x33)
+#define OV2735_REG_CLOCK_REG2			OV2735_PAGE_REG8(0x00, 0x35)
+
+/* Page 1 */
+#define OV2735_REG_STREAM_CTRL			OV2735_PAGE_REG8(0x01, 0xa0)
+#define OV2735_STREAM_CTRL_ON			0x01
+#define OV2735_STREAM_CTRL_OFF			0x00
+
+#define OV2735_REG_UPDOWN_MIRROR		OV2735_PAGE_REG8(0x01, 0x3f)
+#define OV2735_REG_BINNING_DAC_CODE_MODE	OV2735_PAGE_REG8(0x01, 0x30)
+#define OV2735_REG_FRAME_LENGTH			OV2735_PAGE_REG16(0x01, 0x0e)
+#define OV2735_FRAME_LENGTH_MAX			0x0fff
+#define OV2735_REG_FRAME_EXP_SEPERATE_EN	OV2735_PAGE_REG8(0x01, 0x0d)
+#define OV2735_FRAME_EXP_SEPERATE_EN		0x10
+#define OV2735_REG_FRAME_SYNC			OV2735_PAGE_REG8(0x01, 0x01)
+
+#define OV2735_REG_HBLANK			OV2735_PAGE_REG16(0x01, 0x09)
+
+#define OV2735_REG_HS_MIPI			OV2735_PAGE_REG8(0x01, 0xb1)
+#define OV2735_REG_MIPI_CTRL1			OV2735_PAGE_REG8(0x01, 0x92)
+#define OV2735_REG_MIPI_CTRL2			OV2735_PAGE_REG8(0x01, 0x94)
+#define OV2735_REG_MIPI_CTRL3			OV2735_PAGE_REG8(0x01, 0xa1)
+#define OV2735_REG_MIPI_CTRL4			OV2735_PAGE_REG8(0x01, 0xb2)
+#define OV2735_REG_MIPI_CTRL5			OV2735_PAGE_REG8(0x01, 0xb3)
+#define OV2735_REG_MIPI_CTRL6			OV2735_PAGE_REG8(0x01, 0xb4)
+#define OV2735_REG_MIPI_CTRL7			OV2735_PAGE_REG8(0x01, 0xb5)
+#define OV2735_REG_HIGH_SPEED			OV2735_PAGE_REG8(0x01, 0x9d)
+#define OV2735_REG_PREPARE			OV2735_PAGE_REG8(0x01, 0x95)
+#define OV2735_REG_R_HS_ZERO			OV2735_PAGE_REG8(0x01, 0x96)
+#define OV2735_REG_TRAIL			OV2735_PAGE_REG8(0x01, 0x98)
+#define OV2735_REG_R_CLK_ZERO			OV2735_PAGE_REG8(0x01, 0x9c)
+#define OV2735_REG_MIPI_COLOMN_NUMBER		OV2735_PAGE_REG16(0x01, 0x8e)
+#define OV2735_REG_MIPI_LINE_NUMBER		OV2735_PAGE_REG16(0x01, 0x90)
+
+/* Timing control registers */
+#define OV2735_REG_TIMING_CTRL2			OV2735_PAGE_REG8(0x01, 0x1a)
+#define OV2735_REG_TIMING_CTRL3			OV2735_PAGE_REG8(0x01, 0x1c)
+#define OV2735_REG_TIMING_CTRL1			OV2735_PAGE_REG8(0x01, 0x16)
+#define OV2735_REG_RST_NUM			OV2735_PAGE_REG16(0x01, 0x10)
+#define OV2735_REG_RST_NUM2			OV2735_PAGE_REG16(0x01, 0x32)
+#define OV2735_REG_BOOST_EN			OV2735_PAGE_REG8(0x01, 0xd0)
+#define OV2735_REG_B2_NUM			OV2735_PAGE_REG16(0x01, 0xd1)
+#define OV2735_REG_B4_NUM			OV2735_PAGE_REG16(0x01, 0xd3)
+#define OV2735_REG_PIXEL_CYCLE_P0		OV2735_PAGE_REG8(0x01, 0x50)
+#define OV2735_REG_PIXEL_CYCLE_P1		OV2735_PAGE_REG8(0x01, 0x51)
+#define OV2735_REG_PIXEL_CYCLE_P2		OV2735_PAGE_REG8(0x01, 0x52)
+#define OV2735_REG_PIXEL_CYCLE_P3		OV2735_PAGE_REG8(0x01, 0x53)
+#define OV2735_REG_PIXEL_CYCLE_P5		OV2735_PAGE_REG8(0x01, 0x55)
+#define OV2735_REG_PIXEL_CYCLE_P7		OV2735_PAGE_REG16(0x01, 0x57)
+#define OV2735_REG_PIXEL_CYCLE_P9		OV2735_PAGE_REG8(0x01, 0x5a)
+#define OV2735_REG_PIXEL_CYCLE_P10		OV2735_PAGE_REG8(0x01, 0x5b)
+#define OV2735_REG_PIXEL_CYCLE_P12		OV2735_PAGE_REG8(0x01, 0x5d)
+#define OV2735_REG_PIXEL_CYCLE_P18		OV2735_PAGE_REG8(0x01, 0x64)
+#define OV2735_REG_PIXEL_CYCLE_P20		OV2735_PAGE_REG8(0x01, 0x66)
+#define OV2735_REG_PIXEL_CYCLE_P22		OV2735_PAGE_REG8(0x01, 0x68)
+#define OV2735_REG_PIXEL_CYCLE_P33		OV2735_PAGE_REG8(0x01, 0x74)
+#define OV2735_REG_PIXEL_CYCLE_P34		OV2735_PAGE_REG8(0x01, 0x76)
+#define OV2735_REG_PIXEL_CYCLE_P35_P36		OV2735_PAGE_REG8(0x01, 0x77)
+#define OV2735_REG_PIXEL_CYCLE_P37_P38		OV2735_PAGE_REG8(0x01, 0x78)
+#define OV2735_REG_PIXEL_CYCLE_P31		OV2735_PAGE_REG8(0x01, 0x72)
+#define OV2735_REG_PIXEL_CYCLE_P32		OV2735_PAGE_REG8(0x01, 0x73)
+#define OV2735_REG_PIXEL_CYCLE_P44		OV2735_PAGE_REG8(0x01, 0x7d)
+#define OV2735_REG_PIXEL_CYCLE_P45		OV2735_PAGE_REG8(0x01, 0x7e)
+#define OV2735_REG_PIXEL_BIAS_CTRL_RH_RL	OV2735_PAGE_REG8(0x01, 0x8a)
+#define OV2735_REG_PIXEL_BIAS_CTRL_SH_SL	OV2735_PAGE_REG8(0x01, 0x8b)
+
+/* Analog Control registers */
+#define OV2735_REG_ICOMP			OV2735_PAGE_REG8(0x01, 0x19)
+#define OV2735_REG_PCP_RST_SEL			OV2735_PAGE_REG8(0x01, 0x21)
+#define OV2735_REG_VNCP				OV2735_PAGE_REG8(0x01, 0x20)
+#define OV2735_REG_ANALOG_CTRL3			OV2735_PAGE_REG8(0x01, 0x25)
+#define OV2735_REG_ANALOG_CTRL4			OV2735_PAGE_REG8(0x01, 0x26)
+#define OV2735_REG_ANALOG_CTRL5			OV2735_PAGE_REG8(0x01, 0x29)
+#define OV2735_REG_ANALOG_CTRL6			OV2735_PAGE_REG8(0x01, 0x2a)
+#define OV2735_REG_ANALOG_CTRL8			OV2735_PAGE_REG8(0x01, 0x2c)
+
+/* BLC registers */
+#define OV2735_REG_BLC_GAIN_BLUE		OV2735_PAGE_REG8(0x01, 0x86)
+#define OV2735_REG_BLC_GAIN_RED			OV2735_PAGE_REG8(0x01, 0x87)
+#define OV2735_REG_BLC_GAIN_GR			OV2735_PAGE_REG8(0x01, 0x88)
+#define OV2735_REG_BLC_GAIN_GB			OV2735_PAGE_REG8(0x01, 0x89)
+#define OV2735_REG_GB_SUBOFFSET			OV2735_PAGE_REG8(0x01, 0xf0)
+#define OV2735_REG_BLUE_SUBOFFSET		OV2735_PAGE_REG8(0x01, 0xf1)
+#define OV2735_REG_RED_SUBOFFSET		OV2735_PAGE_REG8(0x01, 0xf2)
+#define OV2735_REG_GR_SUBOFFSET			OV2735_PAGE_REG8(0x01, 0xf3)
+#define OV2735_REG_BLC_BPC_TH_P			OV2735_PAGE_REG8(0x01, 0xfc)
+#define OV2735_REG_BLC_BPC_TH_N			OV2735_PAGE_REG8(0x01, 0xfe)
+#define OV2735_REG_ABL				OV2735_PAGE_REG8(0x01, 0xfb)
+
+#define OV2735_REG_TEST_PATTERN			OV2735_PAGE_REG8(0x01, 0xb2)
+#define OV2735_TEST_PATTERN_ENABLE		0x01
+#define OV2735_TEST_PATTERN_DISABLE		0xfe
+
+#define OV2735_REG_LONG_EXPOSURE		OV2735_PAGE_REG16(0x01, 0x03)
+#define OV2735_EXPOSURE_MIN			4
+#define OV2735_EXPOSURE_STEP			1
+#define OV2735_EXPOSURE_MARGIN			4
+
+#define OV2735_REG_ANALOG_GAIN			OV2735_PAGE_REG8(0x01, 0x24)
+#define OV2735_ANALOG_GAIN_MIN			0x10
+#define OV2735_ANALOG_GAIN_MAX			0xff
+#define OV2735_ANALOG_GAIN_STEP			1
+#define OV2735_ANALOG_GAIN_DEFAULT		0x10
+
+/* Page 2 */
+#define OV2735_REG_V_START			OV2735_PAGE_REG16(0x02, 0xa0)
+#define OV2735_REG_V_SIZE			OV2735_PAGE_REG16(0x02, 0xa2)
+#define OV2735_REG_H_START			OV2735_PAGE_REG16(0x02, 0xa4)
+#define OV2735_REG_H_SIZE			OV2735_PAGE_REG16(0x02, 0xa6)
+
+#define OV2735_LINK_FREQ_420MHZ			(420 * HZ_PER_MHZ)
+#define OV2735_PIXEL_RATE			(168 * HZ_PER_MHZ)
+
+/* OV2735 native and active pixel array size */
+static const struct v4l2_rect ov2735_native_area = {
+	.top = 0,
+	.left = 0,
+	.width = 1936,
+	.height = 1096,
+};
+
+static const struct v4l2_rect ov2735_active_area = {
+	.top = 8,
+	.left = 8,
+	.width = 1920,
+	.height = 1080,
+};
+
+static const char * const ov2735_supply_name[] = {
+	"avdd",		/* Analog power */
+	"dovdd",	/* Digital I/O power */
+	"dvdd",		/* Digital core power */
+};
+
+/* PLL_OUT = [PLL_IN * (pll_nc +3)] / [(pll_mc + 1) * (pll_outdiv + 1)] */
+struct ov2735_pll_parameters {
+	u8 pll_nc;
+	u8 pll_mc;
+	u8 pll_outdiv;
+};
+
+struct ov2735 {
+	struct device *dev;
+	struct regmap *cci;
+	struct v4l2_subdev sd;
+	struct media_pad pad;
+	struct clk *xclk;
+	struct gpio_desc *reset_gpio;
+	struct gpio_desc *enable_gpio;
+	struct regulator_bulk_data supplies[ARRAY_SIZE(ov2735_supply_name)];
+
+	/* V4L2 Controls */
+	struct v4l2_ctrl_handler handler;
+	struct v4l2_ctrl *link_freq;
+	struct v4l2_ctrl *pixel_rate;
+	struct v4l2_ctrl *hblank;
+	struct v4l2_ctrl *vblank;
+	struct v4l2_ctrl *gain;
+	struct v4l2_ctrl *exposure;
+	struct v4l2_ctrl *test_pattern;
+
+	u32 link_freq_index;
+
+	u8 current_page;
+	struct mutex page_lock;
+};
+
+struct ov2735_mode {
+	u32 width;
+	u32 height;
+	u32 hts_def;
+	u32 vts_def;
+	u32 exp_def;
+	struct v4l2_rect crop;
+};
+
+static const struct cci_reg_sequence ov2735_common_regs[] = {
+	{ OV2735_REG_CLK_MODE,			0x15 },
+	{ OV2735_REG_CLOCK_REG1,		0x01 },
+	{ OV2735_REG_CLOCK_REG2,		0x20 },
+	{ OV2735_REG_BINNING_DAC_CODE_MODE,	0x00 },
+	{ OV2735_REG_ABL,			0x73 },
+	{ OV2735_REG_FRAME_SYNC,		0x01 },
+
+	/* Timing ctrl */
+	{ OV2735_REG_TIMING_CTRL2,		0x6b },
+	{ OV2735_REG_TIMING_CTRL3,		0xea },
+	{ OV2735_REG_TIMING_CTRL1,		0x0c },
+	{ OV2735_REG_RST_NUM,			0x0063 },
+	{ OV2735_REG_RST_NUM2,			0x006f },
+	{ OV2735_REG_BOOST_EN,			0x02 },
+	{ OV2735_REG_B2_NUM,			0x0120 },
+	{ OV2735_REG_B4_NUM,			0x042a },
+	{ OV2735_REG_PIXEL_CYCLE_P0,		0x00 },
+	{ OV2735_REG_PIXEL_CYCLE_P1,		0x2c },
+	{ OV2735_REG_PIXEL_CYCLE_P2,		0x29 },
+	{ OV2735_REG_PIXEL_CYCLE_P3,		0x00 },
+	{ OV2735_REG_PIXEL_CYCLE_P5,		0x44 },
+	{ OV2735_REG_PIXEL_CYCLE_P7,		0x0029 },
+	{ OV2735_REG_PIXEL_CYCLE_P9,		0x00 },
+	{ OV2735_REG_PIXEL_CYCLE_P10,		0x00 },
+	{ OV2735_REG_PIXEL_CYCLE_P12,		0x00 },
+	{ OV2735_REG_PIXEL_CYCLE_P18,		0x2f },
+	{ OV2735_REG_PIXEL_CYCLE_P20,		0x62 },
+	{ OV2735_REG_PIXEL_CYCLE_P22,		0x5b },
+	{ OV2735_REG_PIXEL_CYCLE_P33,		0x0046 },
+	{ OV2735_REG_PIXEL_CYCLE_P34,		0x36 },
+	{ OV2735_REG_PIXEL_CYCLE_P35_P36,	0x4f },
+	{ OV2735_REG_PIXEL_CYCLE_P37_P38,	0xef },
+	{ OV2735_REG_PIXEL_CYCLE_P31,		0xcf },
+	{ OV2735_REG_PIXEL_CYCLE_P32,		0x36 },
+	{ OV2735_REG_PIXEL_CYCLE_P44,		0x0d },
+	{ OV2735_REG_PIXEL_CYCLE_P45,		0x0d },
+	{ OV2735_REG_PIXEL_BIAS_CTRL_RH_RL,	0x77 },
+	{ OV2735_REG_PIXEL_BIAS_CTRL_SH_SL,	0x77 },
+
+	/* Analog ctrl */
+	{ OV2735_REG_ANALOG_CTRL4,		0x5a },
+	{ OV2735_REG_ANALOG_CTRL5,		0x01 },
+	{ OV2735_REG_ANALOG_CTRL6,		0xd2 },
+	{ OV2735_REG_ANALOG_CTRL8,		0x40 },
+	{ OV2735_REG_PCP_RST_SEL,		0x00 },
+	{ OV2735_REG_ICOMP,			0xc3 },
+
+	{ OV2735_REG_HS_MIPI,			0x83 },
+	{ OV2735_REG_MIPI_CTRL5,		0x0b },
+	{ OV2735_REG_MIPI_CTRL6,		0x14 },
+	{ OV2735_REG_HIGH_SPEED,		0x40 },
+	{ OV2735_REG_MIPI_CTRL3,		0x05 },
+	{ OV2735_REG_MIPI_CTRL2,		0x44 },
+	{ OV2735_REG_PREPARE,			0x33 },
+	{ OV2735_REG_R_HS_ZERO,			0x1f },
+	{ OV2735_REG_TRAIL,			0x45 },
+	{ OV2735_REG_R_CLK_ZERO,		0x10 },
+	{ OV2735_REG_MIPI_CTRL7,		0x70 },
+	{ OV2735_REG_ANALOG_CTRL3,		0xe0 },
+	{ OV2735_REG_VNCP,			0x7b },
+
+	/* BLC */
+	{ OV2735_REG_BLC_GAIN_BLUE,		0x77 },
+	{ OV2735_REG_BLC_GAIN_GB,		0x77 },
+	{ OV2735_REG_BLC_GAIN_RED,		0x74 },
+	{ OV2735_REG_BLC_GAIN_GR,		0x74 },
+	{ OV2735_REG_BLC_BPC_TH_P,		0xe0 },
+	{ OV2735_REG_BLC_BPC_TH_N,		0xe0 },
+	{ OV2735_REG_GB_SUBOFFSET,		0x40 },
+	{ OV2735_REG_BLUE_SUBOFFSET,		0x40 },
+	{ OV2735_REG_RED_SUBOFFSET,		0x40 },
+	{ OV2735_REG_GR_SUBOFFSET,		0x40 },
+};
+
+static const struct ov2735_mode supported_modes[] = {
+	{
+		.width = 1920,
+		.height = 1080,
+		.exp_def = 399,
+		.hts_def = 2200,
+		.vts_def = 2545,
+		.crop = {
+			.top = 8,
+			.left = 8,
+			.width = 1920,
+			.height = 1080,
+		},
+	},
+};
+
+static const s64 link_freq_menu_items[] = {
+	OV2735_LINK_FREQ_420MHZ,
+};
+
+static const struct ov2735_pll_parameters pll_configs[] = {
+	/* For 420MHz pll_configs */
+	{
+		.pll_nc = 4,
+		.pll_mc = 0,
+		.pll_outdiv = 1,
+	},
+};
+
+static const char * const ov2735_test_pattern_menu[] = {
+	"Disabled",
+	"Vertical Color",
+};
+
+static int ov2735_page_access(struct ov2735 *ov2735, u32 reg, int *err)
+{
+	u8 page = reg >> CCI_REG_PRIVATE_SHIFT;
+	int ret = 0;
+
+	if (err && *err)
+		return *err;
+
+	guard(mutex)(&ov2735->page_lock);
+
+	/* Perform page access before read/write */
+	if (ov2735->current_page == page)
+		return ret;
+
+	ret = cci_write(ov2735->cci, OV2735_REG_PAGE_SELECT, page, err);
+	if (!ret)
+		ov2735->current_page = page;
+
+	return ret;
+}
+
+static int ov2735_read(struct ov2735 *ov2735, u32 reg, u64 *val, int *err)
+{
+	u32 addr = reg & ~CCI_REG_PRIVATE_MASK;
+	int ret;
+
+	ret = ov2735_page_access(ov2735, reg, err);
+	if (ret)
+		return ret;
+
+	return cci_read(ov2735->cci, addr, val, err);
+}
+
+static int ov2735_write(struct ov2735 *ov2735, u32 reg, u64 val, int *err)
+{
+	u32 addr = reg & ~CCI_REG_PRIVATE_MASK;
+	int ret;
+
+	ret = ov2735_page_access(ov2735, reg, err);
+	if (ret)
+		return ret;
+
+	return cci_write(ov2735->cci, addr, val, err);
+}
+
+static int ov2735_multi_reg_write(struct ov2735 *ov2735,
+				  const struct cci_reg_sequence *regs,
+				  unsigned int num_regs, int *err)
+{
+	unsigned int i;
+	int ret;
+
+	for (i = 0; i < num_regs; i++) {
+		ret = ov2735_write(ov2735, regs[i].reg, regs[i].val, err);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+static inline struct ov2735 *to_ov2735(struct v4l2_subdev *_sd)
+{
+	return container_of(_sd, struct ov2735, sd);
+}
+
+static int ov2735_enable_test_pattern(struct ov2735 *ov2735, u32 pattern)
+{
+	int ret;
+	u64 val;
+
+	ret = ov2735_read(ov2735, OV2735_REG_TEST_PATTERN, &val, NULL);
+	if (ret)
+		return ret;
+
+	switch (pattern) {
+	case 0:
+		val &= ~OV2735_TEST_PATTERN_ENABLE;
+		break;
+	case 1:
+		val |= OV2735_TEST_PATTERN_ENABLE;
+		break;
+	}
+
+	return ov2735_write(ov2735, OV2735_REG_TEST_PATTERN, val, NULL);
+}
+
+static int ov2735_set_ctrl(struct v4l2_ctrl *ctrl)
+{
+	struct ov2735 *ov2735 = container_of(ctrl->handler, struct ov2735,
+					     handler);
+	struct v4l2_mbus_framefmt *fmt;
+	struct v4l2_subdev_state *state;
+	u64 vts;
+	int ret = 0;
+
+	state = v4l2_subdev_get_locked_active_state(&ov2735->sd);
+	fmt = v4l2_subdev_state_get_format(state, 0);
+
+	if (ctrl->id == V4L2_CID_VBLANK) {
+		/* Honour the VBLANK limits when setting exposure */
+		s64 max = fmt->height + ctrl->val - OV2735_EXPOSURE_MARGIN;
+
+		ret = __v4l2_ctrl_modify_range(ov2735->exposure,
+					       ov2735->exposure->minimum, max,
+					       ov2735->exposure->step,
+					       ov2735->exposure->default_value);
+		if (ret)
+			return ret;
+	}
+
+	if (pm_runtime_get_if_in_use(ov2735->dev) == 0)
+		return 0;
+
+	switch (ctrl->id) {
+	case V4L2_CID_EXPOSURE:
+		ov2735_write(ov2735, OV2735_REG_LONG_EXPOSURE, ctrl->val, &ret);
+		break;
+	case V4L2_CID_ANALOGUE_GAIN:
+		ov2735_write(ov2735, OV2735_REG_ANALOG_GAIN, ctrl->val, &ret);
+		break;
+	case V4L2_CID_HBLANK:
+		ov2735_write(ov2735, OV2735_REG_HBLANK, ctrl->val, &ret);
+		break;
+	case V4L2_CID_VBLANK:
+		vts = ctrl->val + fmt->height;
+		ov2735_write(ov2735, OV2735_REG_FRAME_EXP_SEPERATE_EN,
+			     OV2735_FRAME_EXP_SEPERATE_EN, &ret);
+		ov2735_write(ov2735, OV2735_REG_FRAME_LENGTH, vts, &ret);
+		break;
+	case V4L2_CID_TEST_PATTERN:
+		ret = ov2735_enable_test_pattern(ov2735, ctrl->val);
+		break;
+	default:
+		ret = -EINVAL;
+		break;
+	}
+	ov2735_write(ov2735, OV2735_REG_FRAME_SYNC, 0x01, &ret);
+
+	pm_runtime_put(ov2735->dev);
+
+	return ret;
+}
+
+static const struct v4l2_ctrl_ops ov2735_ctrl_ops = {
+	.s_ctrl = ov2735_set_ctrl,
+};
+
+static int ov2735_init_controls(struct ov2735 *ov2735)
+{
+	struct v4l2_ctrl_handler *ctrl_hdlr;
+	struct v4l2_fwnode_device_properties props;
+	const struct ov2735_mode *mode = &supported_modes[0];
+	u64 hblank_def, vblank_def, exp_max;
+	int ret;
+
+	ctrl_hdlr = &ov2735->handler;
+	v4l2_ctrl_handler_init(ctrl_hdlr, 9);
+
+	ov2735->pixel_rate = v4l2_ctrl_new_std(ctrl_hdlr, &ov2735_ctrl_ops,
+					       V4L2_CID_PIXEL_RATE, 0,
+					       OV2735_PIXEL_RATE, 1,
+					       OV2735_PIXEL_RATE);
+
+	ov2735->link_freq = v4l2_ctrl_new_int_menu(ctrl_hdlr, &ov2735_ctrl_ops,
+						   V4L2_CID_LINK_FREQ,
+						   ov2735->link_freq_index,
+						   0, link_freq_menu_items);
+	if (ov2735->link_freq)
+		ov2735->link_freq->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+
+	hblank_def = mode->hts_def - mode->width;
+	ov2735->hblank = v4l2_ctrl_new_std(ctrl_hdlr, &ov2735_ctrl_ops,
+					   V4L2_CID_HBLANK, hblank_def,
+					   hblank_def, 1, hblank_def);
+
+	vblank_def = mode->vts_def - mode->height;
+	ov2735->vblank = v4l2_ctrl_new_std(ctrl_hdlr, &ov2735_ctrl_ops,
+					   V4L2_CID_VBLANK, vblank_def,
+					   OV2735_FRAME_LENGTH_MAX - mode->height,
+					   1, vblank_def);
+
+	exp_max = mode->vts_def - OV2735_EXPOSURE_MARGIN;
+	ov2735->exposure =
+		v4l2_ctrl_new_std(ctrl_hdlr, &ov2735_ctrl_ops,
+				  V4L2_CID_EXPOSURE,
+				  OV2735_EXPOSURE_MIN, exp_max,
+				  OV2735_EXPOSURE_STEP, mode->exp_def);
+
+	ov2735->gain =
+		v4l2_ctrl_new_std(ctrl_hdlr, &ov2735_ctrl_ops,
+				  V4L2_CID_ANALOGUE_GAIN, OV2735_ANALOG_GAIN_MIN,
+				  OV2735_ANALOG_GAIN_MAX, OV2735_ANALOG_GAIN_STEP,
+				  OV2735_ANALOG_GAIN_DEFAULT);
+
+	ov2735->test_pattern =
+		v4l2_ctrl_new_std_menu_items(ctrl_hdlr, &ov2735_ctrl_ops,
+					     V4L2_CID_TEST_PATTERN,
+					     ARRAY_SIZE(ov2735_test_pattern_menu) - 1,
+					     0, 0, ov2735_test_pattern_menu);
+
+	if (ctrl_hdlr->error) {
+		ret = ctrl_hdlr->error;
+		dev_err(ov2735->dev, "control init failed (%d)\n", ret);
+		goto err_handler_free;
+	}
+
+	ret = v4l2_fwnode_device_parse(ov2735->dev, &props);
+	if (ret)
+		goto err_handler_free;
+
+	ret = v4l2_ctrl_new_fwnode_properties(ctrl_hdlr,
+					      &ov2735_ctrl_ops, &props);
+	if (ret)
+		goto err_handler_free;
+
+	ov2735->sd.ctrl_handler = ctrl_hdlr;
+
+	return 0;
+
+err_handler_free:
+	v4l2_ctrl_handler_free(ctrl_hdlr);
+
+	return ret;
+}
+
+static int ov2735_set_pll_ctrl(struct ov2735 *ov2735)
+{
+	const struct ov2735_pll_parameters *pll_parameters;
+	u8 pll_ctrl;
+	u8 pll_outdiv;
+	int ret = 0;
+
+	pll_parameters = &pll_configs[ov2735->link_freq_index];
+
+	/* BIT[7]: pll_clk_sel, BIT[6:2]: pll_nc, BIT[1:0]: pll_mc */
+	pll_ctrl = ((pll_parameters->pll_nc << 2) | (pll_parameters->pll_mc << 0)) &
+		    OV2735_PLL_CTRL_ENABLE;
+
+	pll_outdiv = pll_parameters->pll_outdiv;
+
+	ov2735_write(ov2735, OV2735_REG_PLL_CTRL, pll_ctrl, &ret);
+	ov2735_write(ov2735, OV2735_REG_PLL_OUTDIV, pll_outdiv, &ret);
+
+	return ret;
+}
+
+static int ov2735_set_framefmt(struct ov2735 *ov2735,
+			       struct v4l2_subdev_state *state)
+{
+	const struct v4l2_mbus_framefmt *format;
+	const struct v4l2_rect *crop;
+	int ret = 0;
+
+	format = v4l2_subdev_state_get_format(state, 0);
+	crop = v4l2_subdev_state_get_crop(state, 0);
+
+	ov2735_write(ov2735, OV2735_REG_V_START, crop->top, &ret);
+	ov2735_write(ov2735, OV2735_REG_V_SIZE, format->height, &ret);
+	ov2735_write(ov2735, OV2735_REG_MIPI_LINE_NUMBER, format->height, &ret);
+	ov2735_write(ov2735, OV2735_REG_H_START, crop->left, &ret);
+	/* OV2735_REG_H_SIZE: Image half horizontal size */
+	ov2735_write(ov2735, OV2735_REG_H_SIZE, (format->width / 2), &ret);
+	ov2735_write(ov2735, OV2735_REG_MIPI_COLOMN_NUMBER, format->width, &ret);
+
+	return ret;
+}
+
+static int ov2735_enable_streams(struct v4l2_subdev *sd,
+				 struct v4l2_subdev_state *state, u32 pad,
+				 u64 streams_mask)
+{
+	struct ov2735 *ov2735 = to_ov2735(sd);
+	int ret;
+
+	ret = pm_runtime_resume_and_get(ov2735->dev);
+	if (ret < 0)
+		return ret;
+
+	/* Apply pll settings */
+	ret = ov2735_set_pll_ctrl(ov2735);
+	if (ret) {
+		dev_err(ov2735->dev, "failed to set frame format: %d\n", ret);
+		goto err_rpm_put;
+	}
+
+	ret = ov2735_multi_reg_write(ov2735, ov2735_common_regs,
+				     ARRAY_SIZE(ov2735_common_regs), NULL);
+	if (ret) {
+		dev_err(ov2735->dev, "failed to write common registers\n");
+		goto err_rpm_put;
+	}
+
+	/* Apply format settings */
+	ret = ov2735_set_framefmt(ov2735, state);
+	if (ret) {
+		dev_err(ov2735->dev, "failed to set frame format: %d\n", ret);
+		goto err_rpm_put;
+	}
+
+	/* Apply customized values from user */
+	ret = __v4l2_ctrl_handler_setup(ov2735->sd.ctrl_handler);
+	if (ret)
+		goto err_rpm_put;
+
+	ret = ov2735_write(ov2735, OV2735_REG_STREAM_CTRL,
+			   OV2735_STREAM_CTRL_ON, NULL);
+	if (ret)
+		goto err_rpm_put;
+
+	return 0;
+
+err_rpm_put:
+	pm_runtime_put(ov2735->dev);
+	return ret;
+}
+
+static int ov2735_disable_streams(struct v4l2_subdev *sd,
+				  struct v4l2_subdev_state *state, u32 pad,
+				  u64 streams_mask)
+{
+	struct ov2735 *ov2735 = to_ov2735(sd);
+	int ret;
+
+	ret = ov2735_write(ov2735, OV2735_REG_STREAM_CTRL,
+			   OV2735_STREAM_CTRL_OFF, NULL);
+	if (ret)
+		dev_err(ov2735->dev, "%s failed to set stream\n", __func__);
+
+	pm_runtime_put(ov2735->dev);
+
+	return ret;
+}
+
+static int ov2735_get_selection(struct v4l2_subdev *sd,
+				struct v4l2_subdev_state *sd_state,
+				struct v4l2_subdev_selection *sel)
+{
+	switch (sel->target) {
+	case V4L2_SEL_TGT_CROP:
+		sel->r = *v4l2_subdev_state_get_crop(sd_state, 0);
+		return 0;
+	case V4L2_SEL_TGT_NATIVE_SIZE:
+		sel->r = ov2735_native_area;
+		return 0;
+	case V4L2_SEL_TGT_CROP_DEFAULT:
+	case V4L2_SEL_TGT_CROP_BOUNDS:
+		sel->r = ov2735_active_area;
+		return 0;
+	default:
+		return -EINVAL;
+	}
+}
+
+static int ov2735_enum_mbus_code(struct v4l2_subdev *sd,
+				 struct v4l2_subdev_state *sd_state,
+				 struct v4l2_subdev_mbus_code_enum *code)
+{
+	if (code->index >= 0)
+		return -EINVAL;
+
+	code->code = MEDIA_BUS_FMT_SGRBG10_1X10;
+
+	return 0;
+}
+
+static int ov2735_enum_frame_size(struct v4l2_subdev *sd,
+				  struct v4l2_subdev_state *sd_state,
+				  struct v4l2_subdev_frame_size_enum *fse)
+{
+	if (fse->index >= ARRAY_SIZE(supported_modes))
+		return -EINVAL;
+
+	if (fse->code != MEDIA_BUS_FMT_SGRBG10_1X10)
+		return -EINVAL;
+
+	fse->min_width = supported_modes[fse->index].width;
+	fse->max_width = fse->min_width;
+	fse->min_height = supported_modes[fse->index].height;
+	fse->max_height = fse->min_height;
+
+	return 0;
+}
+
+static int ov2735_set_framing_limits(struct ov2735 *ov2735,
+				     const struct ov2735_mode *mode)
+{
+	u32 hblank, vblank_def;
+	int ret;
+
+	hblank = mode->hts_def - mode->width;
+	ret = __v4l2_ctrl_modify_range(ov2735->hblank, hblank, hblank, 1,
+				       hblank);
+	if (ret)
+		return ret;
+
+	vblank_def = mode->vts_def - mode->height;
+	return __v4l2_ctrl_modify_range(ov2735->vblank, vblank_def,
+					OV2735_FRAME_LENGTH_MAX - mode->height,
+					1, vblank_def);
+}
+
+static int ov2735_set_pad_format(struct v4l2_subdev *sd,
+				 struct v4l2_subdev_state *sd_state,
+				 struct v4l2_subdev_format *fmt)
+{
+	struct v4l2_mbus_framefmt *format;
+	const struct ov2735_mode *mode;
+	struct v4l2_rect *crop;
+	struct ov2735 *ov2735 = to_ov2735(sd);
+	int ret;
+
+	format = v4l2_subdev_state_get_format(sd_state, 0);
+
+	mode = v4l2_find_nearest_size(supported_modes,
+				      ARRAY_SIZE(supported_modes),
+				      width, height,
+				      fmt->format.width, fmt->format.height);
+
+	fmt->format.width = mode->width;
+	fmt->format.height = mode->height;
+	fmt->format.field = V4L2_FIELD_NONE;
+	fmt->format.colorspace = V4L2_COLORSPACE_RAW;
+	fmt->format.quantization = V4L2_QUANTIZATION_FULL_RANGE;
+	fmt->format.xfer_func = V4L2_XFER_FUNC_NONE;
+
+	if (fmt->which == V4L2_SUBDEV_FORMAT_ACTIVE) {
+		ret = ov2735_set_framing_limits(ov2735, mode);
+		if (ret)
+			return ret;
+	}
+
+	*format = fmt->format;
+
+	/* Initialize crop rectangle */
+	crop = v4l2_subdev_state_get_crop(sd_state, 0);
+	*crop = mode->crop;
+
+	return 0;
+}
+
+static int ov2735_init_state(struct v4l2_subdev *sd,
+			     struct v4l2_subdev_state *state)
+{
+	struct v4l2_subdev_format fmt = {
+		.which = V4L2_SUBDEV_FORMAT_TRY,
+		.format = {
+			.code = MEDIA_BUS_FMT_SGRBG10_1X10,
+			.width = supported_modes[0].width,
+			.height = supported_modes[0].height,
+		},
+	};
+
+	ov2735_set_pad_format(sd, state, &fmt);
+
+	return 0;
+}
+
+static const struct v4l2_subdev_video_ops ov2735_video_ops = {
+	.s_stream = v4l2_subdev_s_stream_helper,
+};
+
+static const struct v4l2_subdev_pad_ops ov2735_pad_ops = {
+	.enum_mbus_code = ov2735_enum_mbus_code,
+	.get_fmt = v4l2_subdev_get_fmt,
+	.set_fmt = ov2735_set_pad_format,
+	.get_selection = ov2735_get_selection,
+	.enum_frame_size = ov2735_enum_frame_size,
+	.enable_streams = ov2735_enable_streams,
+	.disable_streams = ov2735_disable_streams,
+};
+
+static const struct v4l2_subdev_ops ov2735_subdev_ops = {
+	.video = &ov2735_video_ops,
+	.pad = &ov2735_pad_ops,
+};
+
+static const struct v4l2_subdev_internal_ops ov2735_internal_ops = {
+	.init_state = ov2735_init_state,
+};
+
+static int ov2735_power_on(struct device *dev)
+{
+	struct v4l2_subdev *sd = dev_get_drvdata(dev);
+	struct ov2735 *ov2735 = to_ov2735(sd);
+	int ret;
+
+	ret = regulator_bulk_enable(ARRAY_SIZE(ov2735_supply_name),
+				    ov2735->supplies);
+	if (ret) {
+		dev_err(ov2735->dev, "failed to enable regulators\n");
+		return ret;
+	}
+
+	gpiod_set_value_cansleep(ov2735->enable_gpio, 1);
+	/* T4: delay from PWDN pulling low to RSTB pulling high */
+	fsleep(4 * USEC_PER_MSEC);
+
+	ret = clk_prepare_enable(ov2735->xclk);
+	if (ret) {
+		dev_err(ov2735->dev, "failed to enable clock\n");
+		goto err_regulator_off;
+	}
+
+	gpiod_set_value_cansleep(ov2735->reset_gpio, 0);
+	/* T5: delay from RSTB pulling high to first I2C command */
+	fsleep(5 * USEC_PER_MSEC);
+
+	return 0;
+
+err_regulator_off:
+	regulator_bulk_disable(ARRAY_SIZE(ov2735_supply_name), ov2735->supplies);
+	return ret;
+}
+
+static int ov2735_power_off(struct device *dev)
+{
+	struct v4l2_subdev *sd = dev_get_drvdata(dev);
+	struct ov2735 *ov2735 = to_ov2735(sd);
+
+	gpiod_set_value_cansleep(ov2735->enable_gpio, 0);
+	clk_disable_unprepare(ov2735->xclk);
+	gpiod_set_value_cansleep(ov2735->reset_gpio, 1);
+	regulator_bulk_disable(ARRAY_SIZE(ov2735_supply_name), ov2735->supplies);
+
+	return 0;
+}
+
+static int ov2735_get_regulators(struct ov2735 *ov2735)
+{
+	unsigned int i;
+
+	for (i = 0; i < ARRAY_SIZE(ov2735_supply_name); i++)
+		ov2735->supplies[i].supply = ov2735_supply_name[i];
+
+	return devm_regulator_bulk_get(ov2735->dev,
+				       ARRAY_SIZE(ov2735_supply_name),
+				       ov2735->supplies);
+}
+
+static int ov2735_identify_module(struct ov2735 *ov2735)
+{
+	u64 chip_id;
+	int ret;
+
+	ret = ov2735_read(ov2735, OV2735_REG_CHIPID, &chip_id, NULL);
+	if (ret)
+		return dev_err_probe(ov2735->dev, ret,
+				     "failed to read chip id %x\n",
+				     OV2735_CHIPID);
+
+	if (chip_id != OV2735_CHIPID)
+		return dev_err_probe(ov2735->dev, -EIO,
+				     "chip id mismatch: %x!=%llx\n",
+				     OV2735_CHIPID, chip_id);
+
+	return 0;
+}
+
+static int ov2735_parse_endpoint(struct ov2735 *ov2735)
+{
+	struct v4l2_fwnode_endpoint bus_cfg = {
+		.bus_type = V4L2_MBUS_CSI2_DPHY,
+	};
+	struct fwnode_handle *ep;
+	unsigned long link_freq_bitmap;
+	int ret;
+
+	ep = fwnode_graph_get_next_endpoint(dev_fwnode(ov2735->dev), NULL);
+	if (!ep)
+		return dev_err_probe(ov2735->dev, -ENXIO,
+				     "Failed to get next endpoint\n");
+
+	ret = v4l2_fwnode_endpoint_alloc_parse(ep, &bus_cfg);
+	fwnode_handle_put(ep);
+	if (ret)
+		return ret;
+
+	if (bus_cfg.bus.mipi_csi2.num_data_lanes != 2) {
+		ret = dev_err_probe(ov2735->dev, -EINVAL,
+				    "only 2 data lanes are supported\n");
+		goto error_out;
+	}
+
+	ret = v4l2_link_freq_to_bitmap(ov2735->dev, bus_cfg.link_frequencies,
+				       bus_cfg.nr_of_link_frequencies,
+				       link_freq_menu_items,
+				       ARRAY_SIZE(link_freq_menu_items),
+				       &link_freq_bitmap);
+	if (ret) {
+		ret = dev_err_probe(ov2735->dev, -EINVAL,
+				    "only 420MHz frequency is available\n");
+		goto error_out;
+	}
+
+	ov2735->link_freq_index = __ffs(link_freq_bitmap);
+
+error_out:
+	v4l2_fwnode_endpoint_free(&bus_cfg);
+
+	return ret;
+};
+
+static int ov2735_probe(struct i2c_client *client)
+{
+	struct ov2735 *ov2735;
+	unsigned int xclk_freq;
+	int ret;
+
+	ov2735 = devm_kzalloc(&client->dev, sizeof(*ov2735), GFP_KERNEL);
+	if (!ov2735)
+		return -ENOMEM;
+
+	ov2735->dev = &client->dev;
+
+	v4l2_i2c_subdev_init(&ov2735->sd, client, &ov2735_subdev_ops);
+	ov2735->sd.internal_ops = &ov2735_internal_ops;
+
+	ov2735->cci = devm_cci_regmap_init_i2c(client, 8);
+	if (IS_ERR(ov2735->cci))
+		return dev_err_probe(ov2735->dev, PTR_ERR(ov2735->cci),
+				     "failed to initialize CCI\n");
+
+	/* Set Current page to 0 */
+	ov2735->current_page = 0;
+
+	ret = devm_mutex_init(ov2735->dev, &ov2735->page_lock);
+	if (ret)
+		return dev_err_probe(ov2735->dev, ret,
+				     "Failed to initialize lock\n");
+
+	/* Get system clock (xvclk) */
+	ov2735->xclk = devm_v4l2_sensor_clk_get(ov2735->dev, NULL);
+	if (IS_ERR(ov2735->xclk))
+		return dev_err_probe(ov2735->dev, PTR_ERR(ov2735->xclk),
+				     "failed to get xclk\n");
+
+	xclk_freq = clk_get_rate(ov2735->xclk);
+	if (xclk_freq != OV2735_XCLK_FREQ)
+		return dev_err_probe(ov2735->dev, -EINVAL,
+				     "xclk frequency not supported: %u Hz\n",
+				     xclk_freq);
+
+	ret = ov2735_get_regulators(ov2735);
+	if (ret)
+		return dev_err_probe(ov2735->dev, ret,
+				     "failed to get regulators\n");
+
+	ret = ov2735_parse_endpoint(ov2735);
+	if (ret)
+		return dev_err_probe(ov2735->dev, ret,
+				     "failed to parse endpoint configuration\n");
+
+	ov2735->reset_gpio = devm_gpiod_get_optional(ov2735->dev,
+						     "reset", GPIOD_OUT_LOW);
+	if (IS_ERR(ov2735->reset_gpio))
+		return dev_err_probe(ov2735->dev, PTR_ERR(ov2735->reset_gpio),
+				     "failed to get reset GPIO\n");
+
+	ov2735->enable_gpio = devm_gpiod_get_optional(ov2735->dev,
+						      "enable", GPIOD_OUT_LOW);
+	if (IS_ERR(ov2735->enable_gpio))
+		return dev_err_probe(ov2735->dev, PTR_ERR(ov2735->enable_gpio),
+				     "failed to get enable GPIO\n");
+
+	ret = ov2735_power_on(ov2735->dev);
+	if (ret)
+		return ret;
+
+	ret = ov2735_identify_module(ov2735);
+	if (ret)
+		goto error_power_off;
+
+	ret = ov2735_init_controls(ov2735);
+	if (ret)
+		goto error_power_off;
+
+	/* Initialize subdev */
+	ov2735->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+	ov2735->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR;
+	ov2735->pad.flags = MEDIA_PAD_FL_SOURCE;
+
+	ret = media_entity_pads_init(&ov2735->sd.entity, 1, &ov2735->pad);
+	if (ret) {
+		dev_err_probe(ov2735->dev, ret, "failed to init entity pads\n");
+		goto error_handler_free;
+	}
+
+	ov2735->sd.state_lock = ov2735->handler.lock;
+	ret = v4l2_subdev_init_finalize(&ov2735->sd);
+	if (ret) {
+		dev_err_probe(ov2735->dev, ret, "subdev init error\n");
+		goto error_media_entity;
+	}
+
+	ret = devm_pm_runtime_get_noresume(ov2735->dev);
+	if (ret) {
+		dev_err_probe(ov2735->dev, ret,
+			      "failed to get runtime PM noresume\n");
+		goto error_subdev_cleanup;
+	}
+
+	ret = devm_pm_runtime_set_active_enabled(ov2735->dev);
+	if (ret) {
+		dev_err_probe(ov2735->dev, ret,
+			      "failed to set runtime PM active+enabled\n");
+		goto error_subdev_cleanup;
+	}
+
+	ret = v4l2_async_register_subdev_sensor(&ov2735->sd);
+	if (ret) {
+		dev_err_probe(ov2735->dev, ret,
+			      "failed to register ov2735 sub-device\n");
+		goto error_subdev_cleanup;
+	}
+
+	return 0;
+
+error_subdev_cleanup:
+	v4l2_subdev_cleanup(&ov2735->sd);
+
+error_media_entity:
+	media_entity_cleanup(&ov2735->sd.entity);
+
+error_handler_free:
+	v4l2_ctrl_handler_free(ov2735->sd.ctrl_handler);
+
+error_power_off:
+	ov2735_power_off(ov2735->dev);
+
+	return ret;
+}
+
+static void ov2735_remove(struct i2c_client *client)
+{
+	struct v4l2_subdev *sd = i2c_get_clientdata(client);
+	struct ov2735 *ov2735 = to_ov2735(sd);
+
+	v4l2_async_unregister_subdev(sd);
+	v4l2_subdev_cleanup(&ov2735->sd);
+	media_entity_cleanup(&sd->entity);
+	v4l2_ctrl_handler_free(ov2735->sd.ctrl_handler);
+}
+
+static DEFINE_RUNTIME_DEV_PM_OPS(ov2735_pm_ops,
+				 ov2735_power_off, ov2735_power_on, NULL);
+
+static const struct of_device_id ov2735_id[] = {
+	{ .compatible = "ovti,ov2735" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, ov2735_id);
+
+static struct i2c_driver ov2735_driver = {
+	.driver = {
+		.name = "ov2735",
+		.pm = pm_ptr(&ov2735_pm_ops),
+		.of_match_table = ov2735_id,
+	},
+	.probe = ov2735_probe,
+	.remove = ov2735_remove,
+};
+module_i2c_driver(ov2735_driver);
+
+MODULE_DESCRIPTION("OV2735 Camera Sensor Driver");
+MODULE_AUTHOR("Hardevsinh Palaniya <hardevsinh.palaniya@siliconsignals.io>");
+MODULE_AUTHOR("Himanshu Bhavani <himanshu.bhavani@siliconsignals.io>");
+MODULE_LICENSE("GPL");
-- 
2.34.1

Re: [PATCH v8 1/2] dt-bindings: media: i2c: Add ov2735 sensor

[Krzysztof Kozlowski]

On 21/08/2025 16:31, Hardevsinh Palaniya wrote:
...

> +OMNIVISION OV2735 SENSOR DRIVER
> +M:	Hardevsinh Palaniya <hardevsinh.palaniya@siliconsignals.io>
> +M:	Himanshu Bhavani <himanshu.bhavani@siliconsignals.io>
> +L:	linux-media@vger.kernel.org
> +S:	Maintained
> +T:	git git://linuxtv.org/media.git


Do you have commit rights here? If no, then drop.

Best regards,
Krzysztof

Re: [PATCH v8 1/2] dt-bindings: media: i2c: Add ov2735 sensor

[Hardevsinh Palaniya]

Hi Sakari,
 
> On 21/08/2025 16:31, Hardevsinh Palaniya wrote:
> ...
> 
> > +OMNIVISION OV2735 SENSOR DRIVER
> > +M:   Hardevsinh Palaniya <hardevsinh.palaniya@siliconsignals.io>
> > +M:   Himanshu Bhavani <himanshu.bhavani@siliconsignals.io>
> > +L:   linux-media@vger.kernel.org
> > +S:   Maintained
> > +T:   git git://linuxtv.org/media.git
> 
> 
> Do you have commit rights here? If no, then drop.
 
If there are no further changes required in the sensor driver, would it be 
possible for you to help with this.
 
or should I send a new version just to drop this one line?
 
Best Regards,
Hardev

Re: [PATCH v8 2/2] media: i2c: add ov2735 image sensor driver

[Hardevsinh Palaniya]

Hi Sakari,
 
> Add a v4l2 subdevice driver for the Omnivision OV2735 sensor.
>
> The Omnivision OV2735 is a 1/2.7-Inch CMOS image sensor with an
> active array size of 1920 x 1080.
>
> The following features are supported:
> - Manual exposure an gain control support
> - vblank/hblank control support
> - Test pattern support control
> - Supported resolution: 1920 x 1080 @ 30fps (SGRBG10)
 
I’m preparing to submit v9, incorporating Krzysztof’s feedback.
 
Please let me know if any changes are needed for the driver, 
so I can address them in v9.
 
Best Regards,
Hardev

Re: [PATCH v8 0/2] media: i2c: Add ov2735 camera sensor driver

[Sakari Ailus]

Hi Hardev,

On Thu, Aug 21, 2025 at 08:01:11PM +0530, Hardevsinh Palaniya wrote:
> The Omnivision OV2735 is a 1/2.7-Inch CMOS image sensor with an                 
> active array size of 1920 x 1080.                                               

Have you run v4l2-compliance on this? Could you do so and provide the
report, please?

-- 
Kind regards,

Sakari Ailus