Re: [PATCH v1 5/8] arm64: dts: renesas: white-hawk-cpu: Add DP output support

[Laurent Pinchart <laurent.pinchart@ideasonboard.com>]

Hi Tomi,

Thank you for the patch.

On Thu, Nov 17, 2022 at 02:25:44PM +0200, Tomi Valkeinen wrote:
> From: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
> 
> Add DT nodes needed for the mini DP connector. The DP is driven by
> sn65dsi86, which in turn gets the pixel data from the SoC via DSI.
> 
> Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

> ---
>  .../dts/renesas/r8a779g0-white-hawk-cpu.dtsi  | 94 +++++++++++++++++++
>  1 file changed, 94 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/renesas/r8a779g0-white-hawk-cpu.dtsi b/arch/arm64/boot/dts/renesas/r8a779g0-white-hawk-cpu.dtsi
> index c10740aee9f6..8aab859aac7a 100644
> --- a/arch/arm64/boot/dts/renesas/r8a779g0-white-hawk-cpu.dtsi
> +++ b/arch/arm64/boot/dts/renesas/r8a779g0-white-hawk-cpu.dtsi
> @@ -97,6 +97,15 @@ memory@600000000 {
>  		reg = <0x6 0x00000000 0x1 0x00000000>;
>  	};
>  
> +	reg_1p2v: regulator-1p2v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "fixed-1.2V";
> +		regulator-min-microvolt = <1200000>;
> +		regulator-max-microvolt = <1200000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +	};
> +
>  	reg_1p8v: regulator-1p8v {
>  		compatible = "regulator-fixed";
>  		regulator-name = "fixed-1.8V";
> @@ -114,6 +123,24 @@ reg_3p3v: regulator-3p3v {
>  		regulator-boot-on;
>  		regulator-always-on;
>  	};
> +
> +	mini-dp-con {
> +		compatible = "dp-connector";
> +		label = "CN5";
> +		type = "mini";
> +
> +		port {
> +			mini_dp_con_in: endpoint {
> +				remote-endpoint = <&sn65dsi86_out>;
> +			};
> +		};
> +	};
> +
> +	sn65dsi86_refclk: clk-x6 {
> +		compatible = "fixed-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <38400000>;
> +	};
>  };
>  
>  &avb0 {
> @@ -134,6 +161,23 @@ phy0: ethernet-phy@0 {
>  	};
>  };
>  
> +&dsi0 {
> +	status = "okay";
> +
> +	ports {
> +		port@1 {
> +			dsi0_out: endpoint {
> +				remote-endpoint = <&sn65dsi86_in>;
> +				data-lanes = <1 2 3 4>;
> +			};
> +		};
> +	};
> +};
> +
> +&du {
> +	status = "okay";
> +};
> +
>  &extal_clk {
>  	clock-frequency = <16666666>;
>  };
> @@ -172,6 +216,51 @@ eeprom@50 {
>  	};
>  };
>  
> +&i2c1 {
> +	pinctrl-0 = <&i2c1_pins>;
> +	pinctrl-names = "default";
> +
> +	status = "okay";
> +	clock-frequency = <400000>;
> +
> +	bridge@2c {
> +		compatible = "ti,sn65dsi86";
> +		reg = <0x2c>;
> +
> +		clocks = <&sn65dsi86_refclk>;
> +		clock-names = "refclk";
> +
> +		interrupt-parent = <&intc_ex>;
> +		interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
> +
> +		enable-gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>;
> +
> +		vccio-supply = <&reg_1p8v>;
> +		vpll-supply = <&reg_1p8v>;
> +		vcca-supply = <&reg_1p2v>;
> +		vcc-supply = <&reg_1p2v>;
> +
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port@0 {
> +				reg = <0>;
> +				sn65dsi86_in: endpoint {
> +					remote-endpoint = <&dsi0_out>;
> +				};
> +			};
> +
> +			port@1 {
> +				reg = <1>;
> +				sn65dsi86_out: endpoint {
> +					remote-endpoint = <&mini_dp_con_in>;
> +				};
> +			};
> +		};
> +	};
> +};
> +
>  &mmc0 {
>  	pinctrl-0 = <&mmc_pins>;
>  	pinctrl-1 = <&mmc_pins>;
> @@ -221,6 +310,11 @@ i2c0_pins: i2c0 {
>  		function = "i2c0";
>  	};
>  
> +	i2c1_pins: i2c1 {
> +		groups = "i2c1";
> +		function = "i2c1";
> +	};
> +
>  	keys_pins: keys {
>  		pins = "GP_5_0", "GP_5_1", "GP_5_2";
>  		bias-pull-up;

-- 
Regards,

Laurent Pinchart