[PATCH] staging: rtl8723bs: hal: Fix spelling mistakes in comments

[Anup Sharma <anupnewsmail@gmail.com>]

They are appear to be spelling mistakes, initially identified in a codespell report and never been addressed so far.

Signed-off-by: Anup Sharma <anupnewsmail@gmail.com>
---
 drivers/staging/rtl8723bs/hal/rtl8723b_hal_init.c | 14 +++++++-------
 1 file changed, 7 insertions(+), 7 deletions(-)

diff --git a/drivers/staging/rtl8723bs/hal/rtl8723b_hal_init.c b/drivers/staging/rtl8723bs/hal/rtl8723b_hal_init.c
index f1fc077ed29c..0fcae6871108 100644
--- a/drivers/staging/rtl8723bs/hal/rtl8723b_hal_init.c
+++ b/drivers/staging/rtl8723bs/hal/rtl8723b_hal_init.c
@@ -653,7 +653,7 @@ static void Hal_EfusePowerSwitch(
 
 
 	if (PwrState) {
-		/*  To avoid cannot access efuse regsiters after disable/enable several times during DTM test. */
+		/*  To avoid cannot access efuse registers after disable/enable several times during DTM test. */
 		/*  Suggested by SD1 IsaacHsu. 2013.07.08, added by tynli. */
 		tempval = rtw_read8(padapter, SDIO_LOCAL_BASE|SDIO_REG_HSUS_CTRL);
 		if (tempval & BIT(0)) { /*  SDIO local register is suspend */
@@ -1693,7 +1693,7 @@ void rtl8723b_InitBeaconParameters(struct adapter *padapter)
 	rtw_write8(padapter, REG_BCNDMATIM, BCN_DMA_ATIME_INT_TIME_8723B); /*  2ms */
 
 	/*  Suggested by designer timchen. Change beacon AIFS to the largest number */
-	/*  beacause test chip does not contension before sending beacon. by tynli. 2009.11.03 */
+	/*  because test chip does not contension before sending beacon. by tynli. 2009.11.03 */
 	rtw_write16(padapter, REG_BCNTCFG, 0x660F);
 
 	pHalData->RegBcnCtrlVal = rtw_read8(padapter, REG_BCN_CTRL);
@@ -2089,7 +2089,7 @@ void Hal_EfuseParseIDCode(struct adapter *padapter, u8 *hwinfo)
 	u16 EEPROMId;
 
 
-	/*  Checl 0x8129 again for making sure autoload status!! */
+	/*  Check 0x8129 again for making sure autoload status!! */
 	EEPROMId = le16_to_cpu(*((__le16 *)hwinfo));
 	if (EEPROMId != RTL_EEPROM_ID) {
 		pEEPROM->bautoload_fail_flag = true;
@@ -2510,7 +2510,7 @@ static void rtl8723b_cal_txdesc_chksum(struct tx_desc *ptxdesc)
 	/*  Clear first */
 	ptxdesc->txdw7 &= cpu_to_le32(0xffff0000);
 
-	/*  checksume is always calculated by first 32 bytes, */
+	/*  checksum is always calculated by first 32 bytes, */
 	/*  and it doesn't depend on TX DESC length. */
 	/*  Thomas, Lucas@SD4, 20130515 */
 	count = 16;
@@ -2723,7 +2723,7 @@ static void rtl8723b_fill_default_txdesc(
 	 * multicast / mgnt frame should be controlled by Hw because Fw
 	 * will also send null data which we cannot control when Fw LPS
 	 * enable.
-	 * --> default enable non-Qos data sequense number. 2010.06.23.
+	 * --> default enable non-Qos data sequence number. 2010.06.23.
 	 * by tynli.
 	 * (2) Enable HW SEQ control for beacon packet, because we use
 	 * Hw beacon.
@@ -2777,7 +2777,7 @@ void rtl8723b_fill_fake_txdesc(
 	SET_TX_DESC_PKT_SIZE_8723B(pDesc, BufferLen); /*  Buffer size + command header */
 	SET_TX_DESC_QUEUE_SEL_8723B(pDesc, QSLT_MGNT); /*  Fixed queue of Mgnt queue */
 
-	/*  Set NAVUSEHDR to prevent Ps-poll AId filed to be changed to error vlaue by Hw. */
+	/*  Set NAVUSEHDR to prevent Ps-poll AId filed to be changed to error value by Hw. */
 	if (IsPsPoll) {
 		SET_TX_DESC_NAV_USE_HDR_8723B(pDesc, 1);
 	} else {
@@ -3406,7 +3406,7 @@ void SetHwReg8723B(struct adapter *padapter, u8 variable, u8 *val)
 				/*  polling bit, and No Write enable, and address */
 				ulCommand = CAM_CONTENT_COUNT*ucIndex+i;
 				ulCommand = ulCommand | CAM_POLLINIG | CAM_WRITE;
-				/*  write content 0 is equall to mark invalid */
+				/*  write content 0 is equal to mark as invalid */
 				rtw_write32(padapter, WCAMI, ulContent);  /* mdelay(40); */
 				rtw_write32(padapter, RWCAM, ulCommand);  /* mdelay(40); */
 			}
-- 
2.34.1