Re: [patch V2 13/52] x86/fpu: Clean up fpregs_set()

[Borislav Petkov <bp@suse.de>]

On Mon, Jun 14, 2021 at 05:44:21PM +0200, Thomas Gleixner wrote:
> From: Andy Lutomirski <luto@kernel.org>
> 
> fpregs_set() had unnecessary complexity to support short or nonzero-offset
> writes and to handle the case in which a copy from userspace overwrites
> some of the target buffer and then fails.  Support for partial writes is
> useless -- just require that the write have offset 0 and the correct size,
> and copy into a temporary kernel buffer to avoid clobbering the state if
> the user access fails.
> 
> Signed-off-by: Andy Lutomirski <luto@kernel.org>
> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
> ---
> V2: New patch. Picked up from Andy
> ---
>  arch/x86/kernel/fpu/regset.c |   27 ++++++++++++++-------------
>  1 file changed, 14 insertions(+), 13 deletions(-)
> ---
> --- a/arch/x86/kernel/fpu/regset.c
> +++ b/arch/x86/kernel/fpu/regset.c
> @@ -305,31 +305,32 @@ int fpregs_set(struct task_struct *targe
>  	struct user_i387_ia32_struct env;
>  	int ret;
>  
> -	fpu__prepare_write(fpu);
> -	fpstate_sanitize_xstate(fpu);
> +	/* No funny business with partial or oversized writes is permitted. */
> +	if (pos != 0 || count != sizeof(struct user_i387_ia32_struct))
> +		return -EINVAL;
>  
>  	if (!boot_cpu_has(X86_FEATURE_FPU))

cpu_feature_enabled(), and below too, while you're at it.

>  		return fpregs_soft_set(target, regset, pos, count, kbuf, ubuf);
>  
> -	if (!boot_cpu_has(X86_FEATURE_FXSR))
> -		return user_regset_copyin(&pos, &count, &kbuf, &ubuf,
> -					  &fpu->state.fsave, 0,
> -					  -1);
> +	ret = user_regset_copyin(&pos, &count, &kbuf, &ubuf, &env, 0, -1);
> +	if (ret)
> +		return ret;
>  
> -	if (pos > 0 || count < sizeof(env))
> -		convert_from_fxsr(&env, target);
> +	fpu__prepare_write(fpu);
>  
> -	ret = user_regset_copyin(&pos, &count, &kbuf, &ubuf, &env, 0, -1);
> -	if (!ret)
> +	if (static_cpu_has(X86_FEATURE_FXSR))
>  		convert_to_fxsr(&target->thread.fpu.state.fxsave, &env);
> +	else
> +		memcpy(&target->thread.fpu.state.fsave, &env, sizeof(env));
>  
>  	/*
> -	 * update the header bit in the xsave header, indicating the
> +	 * Update the header bit in the xsave header, indicating the
>  	 * presence of FP.
>  	 */
> -	if (boot_cpu_has(X86_FEATURE_XSAVE))
> +	if (static_cpu_has(X86_FEATURE_XSAVE))
>  		fpu->state.xsave.header.xfeatures |= XFEATURE_MASK_FP;
> -	return ret;
> +
> +	return 0;
>  }

With that addressed:

Reviewed-by: Borislav Petkov <bp@suse.de>

Thx.

-- 
Regards/Gruss,
    Boris.

SUSE Software Solutions Germany GmbH, GF: Felix Imendörffer, HRB 36809, AG Nürnberg