Re: I/O page faults from 8250_mid PCIe UART after TIOCVHANGUP

[Andy Shevchenko <andriy.shevchenko@linux.intel.com>]

On Wed, Sep 14, 2022 at 02:10:44PM +0300, Lennert Buytenhek wrote:
> On Wed, Sep 14, 2022 at 01:09:40PM +0300, Andy Shevchenko wrote:
> > > On an Intel SoC with several 8250_mid PCIe UARTs built into the CPU, I
> > > can reliably trigger I/O page faults if I invoke TIOCVHANGUP on any of
> > > the UARTs and then re-open that UART.
> > > 
> > > Invoking TIOCVHANGUP appears to clear the MSI address/data registers
> > > in the UART via tty_ioctl() -> tty_vhangup() -> __tty_hangup() ->
> > > uart_hangup() -> uart_shutdown() -> uart_port_shutdown() ->
> > > univ8250_release_irq() -> free_irq() -> irq_domain_deactivate_irq() ->
> > > __irq_domain_deactivate_irq() -> msi_domain_deactivate() ->
> > > __pci_write_msi_msg():
> > > 
> > > [root@icelake ~]# lspci -s 00:1a.0 -vv | grep -A1 MSI:
> > > 	Capabilities: [40] MSI: Enable+ Count=1/1 Maskable- 64bit-
> > > 		Address: fee00278  Data: 0000
> > > [root@icelake ~]# cat hangup.c
> > > #include <stdio.h>
> > > #include <sys/ioctl.h>
> > > 
> > > int main(int argc, char *argv[])
> > > {
> > > 	ioctl(1, TIOCVHANGUP);
> > > 
> > > 	return 0;
> > > }
> > > [root@icelake ~]# gcc -Wall -o hangup hangup.c
> > > [root@icelake ~]# ./hangup > /dev/ttyS4
> > > [root@icelake ~]# lspci -s 00:1a.0 -vv | grep -A1 MSI:
> > > 	Capabilities: [40] MSI: Enable+ Count=1/1 Maskable- 64bit-
> > > 		Address: 00000000  Data: 0000
> > > [root@icelake ~]#
> > > 
> > > Opening the serial port device again while the UART is in this state
> > > then appears to cause the UART to generate an interrupt
> > 
> > The interrupt is ORed three: DMA Tx, DMA Rx and UART itself.
> > Any of them can be possible, but to be sure, can you add:
> > 
> > 	dev_info(p->dev, "FISR: %x\n", fisr);
> > 
> > into dnv_handle_irq() before any other code and see which bits we
> > actually got there before the crash?
> > 
> > (If it floods the logs, dev_info_ratelimited() may help)
> 
> I think that that wouldn't report anything because when the UART is
> triggering an interrupt here, the MSI address/data are zero, so the
> IRQ handler is not actually invoked.

Ah, indeed. Then you may disable MSI (in 8250_mid) and see that anyway?

> If Ilpo doesn't beat me to it, I'll try adding some debug code to see
> exactly which UART register write in the tty open path is causing the
> UART to signal an interrupt before the IRQ handler is set up.
> 
> (The IOMMU stops the write in this case, so the machine doesn't crash,
> we just get an I/O page fault warning in dmesg every time this happens.)

And I believe you are not using that UART as debug console, so it won't
dead lock itself. It's then better than I assumed.

> > > before the
> > > MSI vector has been set up again, causing a DMA write to I/O virtual
> > > address zero:
> > > 
> > > [root@icelake console]# echo > /dev/ttyS4
> > > [  979.463307] DMAR: DRHD: handling fault status reg 3
> > > [  979.469409] DMAR: [DMA Write NO_PASID] Request device [00:1a.0] fault addr 0x0 [fault reason 0x05] PTE Write access is not set
> > > 
> > > I'm guessing there's something under tty_open() -> uart_open() ->
> > > tty_port_open() -> uart_port_activate() -> uart_port_startup() ->
> > > serial8250_do_startup() that triggers a UART interrupt before the
> > > MSI vector has been set up again.
> > > 
> > > I did a quick search but it didn't seem like this is a known issue.
> > 
> > Thanks for your report and reproducer! Yes, I also never heard about
> > such an issue before. Ilpo, who is doing more UART work nowadays, might
> > have an idea, I hope.
> 
> Thank you!

-- 
With Best Regards,
Andy Shevchenko