Re: [RFC PATCH net-next 04/22] net: dsa: mt7530: improve comments regarding port 5 and 6

[Daniel Golle <daniel@makrotopia.org>]

On Fri, Apr 21, 2023 at 05:36:30PM +0300, arinc9.unal@gmail.com wrote:
> From: Arınç ÜNAL <arinc.unal@arinc9.com>
> 
> There's no logic to numerically order the CPU ports. State the port number
> and its capability of being used as a CPU port instead.
> 
> Remove the irrelevant PHY muxing information from
> mt7530_mac_port_get_caps(). Explain the supported MII modes instead.
> 
> Remove the out of place PHY muxing information from
> mt753x_phylink_mac_config(). The function is for both the MT7530 and MT7531
> switches but there's no PHY muxing on MT7531.
> 
> These comments were gradually introduced with the commits below.
> ca366d6c889b ("net: dsa: mt7530: Convert to PHYLINK API")
> 38f790a80560 ("net: dsa: mt7530: Add support for port 5")
> 88bdef8be9f6 ("net: dsa: mt7530: Extend device data ready for adding a new
> hardware")
> c288575f7810 ("net: dsa: mt7530: Add the support of MT7531 switch")
> 
> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>

Acked-by: Daniel Golle <daniel@makrotopia.org>

> ---
>  drivers/net/dsa/mt7530.c | 19 +++++++++++++------
>  1 file changed, 13 insertions(+), 6 deletions(-)
> 
> diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
> index edc34be745b2..e956ffa1eea8 100644
> --- a/drivers/net/dsa/mt7530.c
> +++ b/drivers/net/dsa/mt7530.c
> @@ -2504,7 +2504,9 @@ static void mt7530_mac_port_get_caps(struct dsa_switch *ds, int port,
>  			  config->supported_interfaces);
>  		break;
>  
> -	case 5: /* 2nd cpu port with phy of port 0 or 4 / external phy */
> +	case 5: /* Port 5 which can be used as a CPU port supports rgmii with
> +		 * delays, mii, and gmii.
> +		 */
>  		phy_interface_set_rgmii(config->supported_interfaces);
>  		__set_bit(PHY_INTERFACE_MODE_MII,
>  			  config->supported_interfaces);
> @@ -2512,7 +2514,9 @@ static void mt7530_mac_port_get_caps(struct dsa_switch *ds, int port,
>  			  config->supported_interfaces);
>  		break;
>  
> -	case 6: /* 1st cpu port */
> +	case 6: /* Port 6 which can be used as a CPU port supports rgmii and
> +		 * trgmii.
> +		 */
>  		__set_bit(PHY_INTERFACE_MODE_RGMII,
>  			  config->supported_interfaces);
>  		__set_bit(PHY_INTERFACE_MODE_TRGMII,
> @@ -2532,14 +2536,17 @@ static void mt7531_mac_port_get_caps(struct dsa_switch *ds, int port,
>  			  config->supported_interfaces);
>  		break;
>  
> -	case 5: /* 2nd cpu port supports either rgmii or sgmii/8023z */
> +	case 5: /* Port 5 which can be used as a CPU port supports rgmii with
> +		 * delays on MT7531BE, sgmii/802.3z on MT7531AE.
> +		 */
>  		if (!priv->p5_sgmii) {
>  			phy_interface_set_rgmii(config->supported_interfaces);
>  			break;
>  		}
>  		fallthrough;
>  
> -	case 6: /* 1st cpu port supports sgmii/8023z only */
> +	case 6: /* Port 6 which can be used as a CPU port supports sgmii/802.3z.
> +		 */
>  		__set_bit(PHY_INTERFACE_MODE_SGMII,
>  			  config->supported_interfaces);
>  		__set_bit(PHY_INTERFACE_MODE_1000BASEX,
> @@ -2731,7 +2738,7 @@ mt753x_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
>  		    state->interface != PHY_INTERFACE_MODE_INTERNAL)
>  			goto unsupported;
>  		break;
> -	case 5: /* 2nd cpu port with phy of port 0 or 4 / external phy */
> +	case 5: /* Port 5, can be used as a CPU port. */
>  		if (priv->p5_interface == state->interface)
>  			break;
>  
> @@ -2741,7 +2748,7 @@ mt753x_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
>  		if (priv->p5_intf_sel != P5_DISABLED)
>  			priv->p5_interface = state->interface;
>  		break;
> -	case 6: /* 1st cpu port */
> +	case 6: /* Port 6, can be used as a CPU port. */
>  		if (priv->p6_interface == state->interface)
>  			break;
>  
> -- 
> 2.37.2
>