Re: [PATCH v4 3/7] mmc: sdhci-of-dwcmshc: Add support for T-Head TH1520

[Drew Fustini <dfustini@baylibre.com>]

On Mon, Nov 06, 2023 at 08:42:38PM +0200, Adrian Hunter wrote:
> On 2/11/23 04:48, Drew Fustini wrote:
> > Add support for the mmc controller in the T-Head TH1520 with the new
> > compatible "thead,th1520-dwcmshc". Implement custom sdhci_ops for
> > set_uhs_signaling, reset, voltage_switch, and platform_execute_tuning.
> > 
> > Signed-off-by: Drew Fustini <dfustini@baylibre.com>
> 
> One question below, otherwise:
> 
> Acked-by: Adrian Hunter <adrian.hunter@intel.com>
> 
> > ---
> >  drivers/mmc/host/sdhci-of-dwcmshc.c | 348 ++++++++++++++++++++++++++++++++++++
> >  1 file changed, 348 insertions(+)
> > 
> > diff --git a/drivers/mmc/host/sdhci-of-dwcmshc.c b/drivers/mmc/host/sdhci-of-dwcmshc.c
> > index 3a3bae6948a8..1a1386b742c1 100644
> > --- a/drivers/mmc/host/sdhci-of-dwcmshc.c
> > +++ b/drivers/mmc/host/sdhci-of-dwcmshc.c
> > @@ -8,6 +8,7 @@
> >   */
> >  
> >  #include <linux/acpi.h>
> > +#include <linux/bitfield.h>
> >  #include <linux/clk.h>
> >  #include <linux/dma-mapping.h>
> >  #include <linux/iopoll.h>
> > @@ -35,6 +36,21 @@
> >  #define DWCMSHC_CARD_IS_EMMC		BIT(0)
> >  #define DWCMSHC_ENHANCED_STROBE		BIT(8)
> >  #define DWCMSHC_EMMC_ATCTRL		0x40
> > +/* Tuning and auto-tuning fields in AT_CTRL_R control register */
> > +#define AT_CTRL_AT_EN			BIT(0) /* autotuning is enabled */
> > +#define AT_CTRL_CI_SEL			BIT(1) /* interval to drive center phase select */
> > +#define AT_CTRL_SWIN_TH_EN		BIT(2) /* sampling window threshold enable */
> > +#define AT_CTRL_RPT_TUNE_ERR		BIT(3) /* enable reporting framing errors */
> > +#define AT_CTRL_SW_TUNE_EN		BIT(4) /* enable software managed tuning */
> > +#define AT_CTRL_WIN_EDGE_SEL_MASK	GENMASK(11, 8) /* bits [11:8] */
> > +#define AT_CTRL_WIN_EDGE_SEL		0xf /* sampling window edge select */
> > +#define AT_CTRL_TUNE_CLK_STOP_EN	BIT(16) /* clocks stopped during phase code change */
> > +#define AT_CTRL_PRE_CHANGE_DLY_MASK	GENMASK(18, 17) /* bits [18:17] */
> > +#define AT_CTRL_PRE_CHANGE_DLY		0x1  /* 2-cycle latency */
> > +#define AT_CTRL_POST_CHANGE_DLY_MASK	GENMASK(20, 19) /* bits [20:19] */
> > +#define AT_CTRL_POST_CHANGE_DLY		0x3  /* 4-cycle latency */
> > +#define AT_CTRL_SWIN_TH_VAL_MASK	GENMASK(31, 24) /* bits [31:24] */
> > +#define AT_CTRL_SWIN_TH_VAL		0x9  /* sampling window threshold */
> >  
> >  /* Rockchip specific Registers */
> >  #define DWCMSHC_EMMC_DLL_CTRL		0x800
> > @@ -72,6 +88,82 @@
> >  	(((x) & DWCMSHC_EMMC_DLL_TIMEOUT) == 0))
> >  #define RK35xx_MAX_CLKS 3
> >  
> > +/* PHY register area pointer */
> > +#define DWC_MSHC_PTR_PHY_R	0x300
> > +
> > +/* PHY general configuration */
> > +#define PHY_CNFG_R		(DWC_MSHC_PTR_PHY_R + 0x00)
> > +#define PHY_CNFG_RSTN_DEASSERT	0x1  /* Deassert PHY reset */
> > +#define PHY_CNFG_PAD_SP_MASK	GENMASK(19, 16) /* bits [19:16] */
> > +#define PHY_CNFG_PAD_SP		0x0c /* PMOS TX drive strength */
> > +#define PHY_CNFG_PAD_SN_MASK	GENMASK(23, 20) /* bits [23:20] */
> > +#define PHY_CNFG_PAD_SN		0x0c /* NMOS TX drive strength */
> > +
> > +/* PHY command/response pad settings */
> > +#define PHY_CMDPAD_CNFG_R	(DWC_MSHC_PTR_PHY_R + 0x04)
> > +
> > +/* PHY data pad settings */
> > +#define PHY_DATAPAD_CNFG_R	(DWC_MSHC_PTR_PHY_R + 0x06)
> > +
> > +/* PHY clock pad settings */
> > +#define PHY_CLKPAD_CNFG_R	(DWC_MSHC_PTR_PHY_R + 0x08)
> > +
> > +/* PHY strobe pad settings */
> > +#define PHY_STBPAD_CNFG_R	(DWC_MSHC_PTR_PHY_R + 0x0a)
> > +
> > +/* PHY reset pad settings */
> > +#define PHY_RSTNPAD_CNFG_R	(DWC_MSHC_PTR_PHY_R + 0x0c)
> > +
> > +/* Bitfields are common for all pad settings */
> > +#define PHY_PAD_RXSEL_1V8		0x1 /* Receiver type select for 1.8V */
> > +#define PHY_PAD_RXSEL_3V3		0x2 /* Receiver type select for 3.3V */
> > +
> > +#define PHY_PAD_WEAKPULL_MASK		GENMASK(4, 3) /* bits [4:3] */
> > +#define PHY_PAD_WEAKPULL_PULLUP		0x1 /* Weak pull up enabled */
> > +#define PHY_PAD_WEAKPULL_PULLDOWN	0x2 /* Weak pull down enabled */
> > +
> > +#define PHY_PAD_TXSLEW_CTRL_P_MASK	GENMASK(8, 5) /* bits [8:5] */
> > +#define PHY_PAD_TXSLEW_CTRL_P		0x3 /* Slew control for P-Type pad TX */
> > +#define PHY_PAD_TXSLEW_CTRL_N_MASK	GENMASK(12, 9) /* bits [12:9] */
> > +#define PHY_PAD_TXSLEW_CTRL_N		0x3 /* Slew control for N-Type pad TX */
> > +
> > +/* PHY CLK delay line settings */
> > +#define PHY_SDCLKDL_CNFG_R		(DWC_MSHC_PTR_PHY_R + 0x1d)
> > +#define PHY_SDCLKDL_CNFG_UPDATE	BIT(4) /* set before writing to SDCLKDL_DC */
> > +
> > +/* PHY CLK delay line delay code */
> > +#define PHY_SDCLKDL_DC_R		(DWC_MSHC_PTR_PHY_R + 0x1e)
> > +#define PHY_SDCLKDL_DC_INITIAL		0x40 /* initial delay code */
> > +#define PHY_SDCLKDL_DC_DEFAULT		0x32 /* default delay code */
> > +#define PHY_SDCLKDL_DC_HS400		0x18 /* delay code for HS400 mode */
> > +
> > +/* PHY drift_cclk_rx delay line configuration setting */
> > +#define PHY_ATDL_CNFG_R			(DWC_MSHC_PTR_PHY_R + 0x21)
> > +#define PHY_ATDL_CNFG_INPSEL_MASK	GENMASK(3, 2) /* bits [3:2] */
> > +#define PHY_ATDL_CNFG_INPSEL		0x3 /* delay line input source */
> > +
> > +/* PHY DLL control settings */
> > +#define PHY_DLL_CTRL_R			(DWC_MSHC_PTR_PHY_R + 0x24)
> > +#define PHY_DLL_CTRL_DISABLE		0x0 /* PHY DLL is enabled */
> > +#define PHY_DLL_CTRL_ENABLE		0x1 /* PHY DLL is disabled */
> > +
> > +/* PHY DLL  configuration register 1 */
> > +#define PHY_DLL_CNFG1_R			(DWC_MSHC_PTR_PHY_R + 0x25)
> > +#define PHY_DLL_CNFG1_SLVDLY_MASK	GENMASK(5, 4) /* bits [5:4] */
> > +#define PHY_DLL_CNFG1_SLVDLY		0x2 /* DLL slave update delay input */
> > +#define PHY_DLL_CNFG1_WAITCYCLE		0x5 /* DLL wait cycle input */
> > +
> > +/* PHY DLL configuration register 2 */
> > +#define PHY_DLL_CNFG2_R			(DWC_MSHC_PTR_PHY_R + 0x26)
> > +#define PHY_DLL_CNFG2_JUMPSTEP		0xa /* DLL jump step input */
> > +
> > +/* PHY DLL master and slave delay line configuration settings */
> > +#define PHY_DLLDL_CNFG_R		(DWC_MSHC_PTR_PHY_R + 0x28)
> > +#define PHY_DLLDL_CNFG_SLV_INPSEL_MASK	GENMASK(6, 5) /* bits [6:5] */
> > +#define PHY_DLLDL_CNFG_SLV_INPSEL	0x3 /* clock source select for slave DL */
> > +
> > +#define FLAG_IO_FIXED_1V8	BIT(0)
> > +
> >  #define BOUNDARY_OK(addr, len) \
> >  	((addr | (SZ_128M - 1)) == ((addr + len - 1) | (SZ_128M - 1)))
> >  
> > @@ -92,6 +184,8 @@ struct dwcmshc_priv {
> >  	struct clk	*bus_clk;
> >  	int vendor_specific_area1; /* P_VENDOR_SPECIFIC_AREA reg */
> >  	void *priv; /* pointer to SoC private stuff */
> > +	u16 delay_line;
> > +	u16 flags;
> >  };
> >  
> >  /*
> > @@ -157,6 +251,126 @@ static void dwcmshc_request(struct mmc_host *mmc, struct mmc_request *mrq)
> >  	sdhci_request(mmc, mrq);
> >  }
> >  
> > +static void dwcmshc_phy_1_8v_init(struct sdhci_host *host)
> > +{
> > +	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> > +	struct dwcmshc_priv *priv = sdhci_pltfm_priv(pltfm_host);
> > +	u32 val;
> > +
> > +	/* deassert phy reset & set tx drive strength */
> > +	val = PHY_CNFG_RSTN_DEASSERT;
> > +	val |= FIELD_PREP(PHY_CNFG_PAD_SP_MASK, PHY_CNFG_PAD_SP);
> > +	val |= FIELD_PREP(PHY_CNFG_PAD_SN_MASK, PHY_CNFG_PAD_SN);
> > +	sdhci_writel(host, val, PHY_CNFG_R);
> > +
> > +	/* disable delay line */
> > +	sdhci_writeb(host, PHY_SDCLKDL_CNFG_UPDATE, PHY_SDCLKDL_CNFG_R);
> > +
> > +	/* set delay line */
> > +	sdhci_writeb(host, priv->delay_line, PHY_SDCLKDL_DC_R);
> > +	sdhci_writeb(host, PHY_DLL_CNFG2_JUMPSTEP, PHY_DLL_CNFG2_R);
> > +
> > +	/* enable delay lane */
> > +	val = sdhci_readb(host, PHY_SDCLKDL_CNFG_R);
> > +	val &= ~(PHY_SDCLKDL_CNFG_UPDATE);
> > +	sdhci_writeb(host, val, PHY_SDCLKDL_CNFG_R);
> > +
> > +	/* configure phy pads */
> > +	val = PHY_PAD_RXSEL_1V8;
> > +	val |= FIELD_PREP(PHY_PAD_WEAKPULL_MASK, PHY_PAD_WEAKPULL_PULLUP);
> > +	val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_P_MASK, PHY_PAD_TXSLEW_CTRL_P);
> > +	val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_N_MASK, PHY_PAD_TXSLEW_CTRL_N);
> > +	sdhci_writew(host, val, PHY_CMDPAD_CNFG_R);
> > +	sdhci_writew(host, val, PHY_DATAPAD_CNFG_R);
> > +	sdhci_writew(host, val, PHY_RSTNPAD_CNFG_R);
> > +
> > +	val = FIELD_PREP(PHY_PAD_TXSLEW_CTRL_P_MASK, PHY_PAD_TXSLEW_CTRL_P);
> > +	val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_N_MASK, PHY_PAD_TXSLEW_CTRL_N);
> > +	sdhci_writew(host, val, PHY_CLKPAD_CNFG_R);
> > +
> > +	val = PHY_PAD_RXSEL_1V8;
> > +	val |= FIELD_PREP(PHY_PAD_WEAKPULL_MASK, PHY_PAD_WEAKPULL_PULLDOWN);
> > +	val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_P_MASK, PHY_PAD_TXSLEW_CTRL_P);
> > +	val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_N_MASK, PHY_PAD_TXSLEW_CTRL_N);
> > +	sdhci_writew(host, val, PHY_STBPAD_CNFG_R);
> > +
> > +	/* enable data strobe mode */
> > +	sdhci_writeb(host, FIELD_PREP(PHY_DLLDL_CNFG_SLV_INPSEL_MASK, PHY_DLLDL_CNFG_SLV_INPSEL),
> > +		     PHY_DLLDL_CNFG_R);
> > +
> > +	/* enable phy dll */
> > +	sdhci_writeb(host, PHY_DLL_CTRL_ENABLE, PHY_DLL_CTRL_R);
> > +}
> > +
> > +static void dwcmshc_phy_3_3v_init(struct sdhci_host *host)
> > +{
> > +	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> > +	struct dwcmshc_priv *priv = sdhci_pltfm_priv(pltfm_host);
> > +	u32 val;
> > +
> > +	/* deassert phy reset & set tx drive strength */
> > +	val = PHY_CNFG_RSTN_DEASSERT;
> > +	val |= FIELD_PREP(PHY_CNFG_PAD_SP_MASK, PHY_CNFG_PAD_SP);
> > +	val |= FIELD_PREP(PHY_CNFG_PAD_SN_MASK, PHY_CNFG_PAD_SN);
> > +	sdhci_writel(host, val, PHY_CNFG_R);
> > +
> > +	/* disable delay line */
> > +	sdhci_writeb(host, PHY_SDCLKDL_CNFG_UPDATE, PHY_SDCLKDL_CNFG_R);
> > +
> > +	/* set delay line */
> > +	sdhci_writeb(host, priv->delay_line, PHY_SDCLKDL_DC_R);
> > +	sdhci_writeb(host, PHY_DLL_CNFG2_JUMPSTEP, PHY_DLL_CNFG2_R);
> > +
> > +	/* enable delay lane */
> > +	val = sdhci_readb(host, PHY_SDCLKDL_CNFG_R);
> > +	val &= ~(PHY_SDCLKDL_CNFG_UPDATE);
> > +	sdhci_writeb(host, val, PHY_SDCLKDL_CNFG_R);
> > +
> > +	/* configure phy pads */
> > +	val = PHY_PAD_RXSEL_3V3;
> > +	val |= FIELD_PREP(PHY_PAD_WEAKPULL_MASK, PHY_PAD_WEAKPULL_PULLUP);
> > +	val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_P_MASK, PHY_PAD_TXSLEW_CTRL_P);
> > +	val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_N_MASK, PHY_PAD_TXSLEW_CTRL_N);
> > +	sdhci_writew(host, val, PHY_CMDPAD_CNFG_R);
> > +	sdhci_writew(host, val, PHY_DATAPAD_CNFG_R);
> > +	sdhci_writew(host, val, PHY_RSTNPAD_CNFG_R);
> > +
> > +	val = FIELD_PREP(PHY_PAD_TXSLEW_CTRL_P_MASK, PHY_PAD_TXSLEW_CTRL_P);
> > +	val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_N_MASK, PHY_PAD_TXSLEW_CTRL_N);
> > +	sdhci_writew(host, val, PHY_CLKPAD_CNFG_R);
> > +
> > +	val = PHY_PAD_RXSEL_3V3;
> > +	val |= FIELD_PREP(PHY_PAD_WEAKPULL_MASK, PHY_PAD_WEAKPULL_PULLDOWN);
> > +	val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_P_MASK, PHY_PAD_TXSLEW_CTRL_P);
> > +	val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_N_MASK, PHY_PAD_TXSLEW_CTRL_N);
> > +	sdhci_writew(host, val, PHY_STBPAD_CNFG_R);
> > +
> > +	/* enable phy dll */
> > +	sdhci_writeb(host, PHY_DLL_CTRL_ENABLE, PHY_DLL_CTRL_R);
> > +}
> > +
> > +static void th1520_sdhci_set_phy(struct sdhci_host *host)
> > +{
> > +	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> > +	struct dwcmshc_priv *priv = sdhci_pltfm_priv(pltfm_host);
> > +	u16 emmc_ctrl;
> > +
> > +	/* Before power on, set PHY configs */
> > +	if (priv->flags & FLAG_IO_FIXED_1V8)
> > +		dwcmshc_phy_1_8v_init(host);
> > +	else
> > +		dwcmshc_phy_3_3v_init(host);
> > +
> > +	if (host->mmc->caps2 & (MMC_CAP2_NO_SD | MMC_CAP2_NO_SDIO)) {
> 
> Perhaps you mean both MMC_CAP2_NO_SD and MMC_CAP2_NO_SDIO which would be as below?
> 
> 	if ((host->mmc->caps2 & (MMC_CAP2_NO_SD | MMC_CAP2_NO_SDIO)) == (MMC_CAP2_NO_SD | MMC_CAP2_NO_SDIO)) {
> 
> or
> 
> 	if (host->mmc->caps2 & MMC_CAP2_NO_SD && host->mmc->caps2 & MMC_CAP2_NO_SDIO) {
> 
> or some such?

Thanks for catching this. Yes, what I did is incorrect.

In fact, Jisheng had suggested this code in the v2 thread:

u32 tmp = MMC_CAP2_NO_SD | MMC_CAP2_NO_SDIO;
if ((cap2 & tmp) == tmp) {
	blablabla...
}

This is similar to your first suggestion above.

I'll fix this in v5.

thanks,
drew