Re: [PATCH V2 1/2 RESEND] arm64: dts: rockchip: Add DTS for FriendlyARM NanoPi R2S Plus

[Daniel Golle <daniel@makrotopia.org>]

On Thu, Aug 01, 2024 at 05:57:35PM +0000, Sergey Bostandzhyan wrote:
> The R2S Plus is basically an R2S with additional eMMC.
> 
> The eMMC configuration for the DTS has been extracted and copied from
> rk3328-nanopi-r2.dts, v2017.09 branch from the friendlyarm/uboot-rockchip
> repository.
> 
> Signed-off-by: Sergey Bostandzhyan <jin@mediatomb.cc>
> ---
>  arch/arm64/boot/dts/rockchip/Makefile         |  1 +
>  .../dts/rockchip/rk3328-nanopi-r2s-plus.dts   | 31 +++++++++++++++++++
>  2 files changed, 32 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s-plus.dts
> 
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> index fda1b980eb4b..36258dc8dafd 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -20,6 +20,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-nanopi-r2c.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-nanopi-r2c-plus.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-nanopi-r2s.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-nanopi-r2s-plus.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-orangepi-r1-plus.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-orangepi-r1-plus-lts.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock64.dtb
> diff --git a/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s-plus.dts b/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s-plus.dts
> new file mode 100644
> index 000000000000..7b83090a2145
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s-plus.dts
> @@ -0,0 +1,31 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * (C) Copyright 2018 FriendlyElec Computer Tech. Co., Ltd.
> + * (http://www.friendlyarm.com)
> + *
> + * (C) Copyright 2016 Rockchip Electronics Co., Ltd
> + */
> +
> +/dts-v1/;
> +#include "rk3328-nanopi-r2s.dts"
> +
> +/ {
> +	model = "FriendlyElec NanoPi R2S Plus";
> +	compatible = "friendlyarm,nanopi-r2s-plus", "rockchip,rk3328";
> +
> +	aliases {
> +		mmc1 = &emmc;
> +	};
> +};
> +
> +&emmc {
> +	bus-width = <8>;
> +	cap-mmc-highspeed;
> +	supports-emmc;
> +	disable-wp;
> +	non-removable;
> +	num-slots = <1>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;

I think it's worth adding

	mmc-hs200-1_8v;


I've tried getting the best speed possible and while HS400 with and
without enhanced strobe did NOT work, hs200 works just fine.
[    0.459863] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0)
[    0.460884] mmc_host mmc1: Bus speed (slot 0) = 150000000Hz (slot req 150000000Hz, actual 150000000HZ div = 0)
...
[    0.728220] dwmmc_rockchip ff520000.mmc: Successfully tuned phase to 194
[    0.728940] mmc1: new HS200 MMC card at address 0001
[    0.730774] mmcblk1: mmc1:0001 A3A551 28.9 GiB
[    0.733262]  mmcblk1: p1 p2
[    0.734562] mmcblk1boot0: mmc1:0001 A3A551 4.00 MiB
[    0.736818] mmcblk1boot1: mmc1:0001 A3A551 4.00 MiB
[    0.738503] mmcblk1rpmb: mmc1:0001 A3A551 16.0 MiB, chardev (245:0)

root@OpenWrt:/# hdparm -t /dev/mmcblk1

/dev/mmcblk1:
 Timing buffered disk reads: 342 MB in  3.00 seconds = 113.81 MB/sec


Without 'mmc-hs200-1_8v' property in DT the eMMC is detected as
[    0.440465] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0)
[    0.442032] mmc1: new high speed MMC card at address 0001
[    0.444261] mmcblk1: mmc1:0001 A3A551 28.9 GiB
[    0.447388]  mmcblk1: p1 p2
[    0.448744] mmcblk1boot0: mmc1:0001 A3A551 4.00 MiB
[    0.451065] mmcblk1boot1: mmc1:0001 A3A551 4.00 MiB
[    0.452871] mmcblk1rpmb: mmc1:0001 A3A551 16.0 MiB, chardev (245:0)


root@OpenWrt:/# hdparm -t /dev/mmcblk1

/dev/mmcblk1:
 Timing buffered disk reads: 134 MB in  3.03 seconds =  44.18 MB/sec


> +	status = "okay";
> +};

I'm right now trying to get SDIO RTL8822CS working, so far I'm out of luck,
but it can be added later once we got it working.