* [PATCH v2 0/5] arm64: qcom: Add support for QCS9075 boards
@ 2024-11-15 22:51 Wasim Nazir
2024-11-15 22:51 ` [PATCH v2 1/5] dt-bindings: arm: qcom,ids: add SoC ID for QCS9075 Wasim Nazir
` (4 more replies)
0 siblings, 5 replies; 10+ messages in thread
From: Wasim Nazir @ 2024-11-15 22:51 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel, kernel, Wasim Nazir
This series:
Add support for Qualcomm's rb8, ride/ride-r3 boards using QCS9075 SoC.
QCS9075 is compatible IoT-industrial grade variant of SA8775p SoC
without safety monitorng feature of SAfetyIsLand subsystem.
This subsystem continues to supports other features like built-in
self-test, error-detection, reset-handling, etc.
Changelog:
v2:
- Remove unused dp nodes & update commit for ride vs ride-r3.
v1: https://lore.kernel.org/all/20241110145339.3635437-1-quic_wasimn@quicinc.com/
Wasim Nazir (5):
dt-bindings: arm: qcom,ids: add SoC ID for QCS9075
soc: qcom: socinfo: add QCS9075 SoC ID
dt-bindings: arm: qcom: Document rb8/ride/ride-r3 on QCS9075
arm64: dts: qcom: Add support for QCS9075 RB8
arm64: dts: qcom: Add support for QCS9075 Ride & Ride-r3
.../devicetree/bindings/arm/qcom.yaml | 9 +
arch/arm64/boot/dts/qcom/Makefile | 3 +
arch/arm64/boot/dts/qcom/qcs9075-rb8.dts | 281 ++++++++++++++++++
arch/arm64/boot/dts/qcom/qcs9075-ride-r3.dts | 12 +
arch/arm64/boot/dts/qcom/qcs9075-ride.dts | 12 +
drivers/soc/qcom/socinfo.c | 1 +
include/dt-bindings/arm/qcom,ids.h | 1 +
7 files changed, 319 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/qcs9075-rb8.dts
create mode 100644 arch/arm64/boot/dts/qcom/qcs9075-ride-r3.dts
create mode 100644 arch/arm64/boot/dts/qcom/qcs9075-ride.dts
base-commit: 929beafbe7acce3267c06115e13e03ff6e50548a
--
2.47.0
^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH v2 1/5] dt-bindings: arm: qcom,ids: add SoC ID for QCS9075
2024-11-15 22:51 [PATCH v2 0/5] arm64: qcom: Add support for QCS9075 boards Wasim Nazir
@ 2024-11-15 22:51 ` Wasim Nazir
2024-11-15 22:51 ` [PATCH v2 2/5] soc: qcom: socinfo: add QCS9075 SoC ID Wasim Nazir
` (3 subsequent siblings)
4 siblings, 0 replies; 10+ messages in thread
From: Wasim Nazir @ 2024-11-15 22:51 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel, kernel, Wasim Nazir
Add the unique ID for Qualcomm QCS9075 SoC.
This value is used to differentiate the SoC across qcom targets.
Signed-off-by: Wasim Nazir <quic_wasimn@quicinc.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
---
include/dt-bindings/arm/qcom,ids.h | 1 +
1 file changed, 1 insertion(+)
diff --git a/include/dt-bindings/arm/qcom,ids.h b/include/dt-bindings/arm/qcom,ids.h
index e850dc3a1ad3..1b3e0176dcb7 100644
--- a/include/dt-bindings/arm/qcom,ids.h
+++ b/include/dt-bindings/arm/qcom,ids.h
@@ -284,6 +284,7 @@
#define QCOM_ID_QCS9100 667
#define QCOM_ID_QCS8300 674
#define QCOM_ID_QCS8275 675
+#define QCOM_ID_QCS9075 676
#define QCOM_ID_QCS615 680
/*
--
2.47.0
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v2 2/5] soc: qcom: socinfo: add QCS9075 SoC ID
2024-11-15 22:51 [PATCH v2 0/5] arm64: qcom: Add support for QCS9075 boards Wasim Nazir
2024-11-15 22:51 ` [PATCH v2 1/5] dt-bindings: arm: qcom,ids: add SoC ID for QCS9075 Wasim Nazir
@ 2024-11-15 22:51 ` Wasim Nazir
2024-11-15 22:51 ` [PATCH v2 3/5] dt-bindings: arm: qcom: Document rb8/ride/ride-r3 on QCS9075 Wasim Nazir
` (2 subsequent siblings)
4 siblings, 0 replies; 10+ messages in thread
From: Wasim Nazir @ 2024-11-15 22:51 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel, kernel, Wasim Nazir,
Dmitry Baryshkov
Update soc_id table for the Qualcomm QCS9075 SoC
to represent qcs9075 machine.
Signed-off-by: Wasim Nazir <quic_wasimn@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
drivers/soc/qcom/socinfo.c | 1 +
1 file changed, 1 insertion(+)
diff --git a/drivers/soc/qcom/socinfo.c b/drivers/soc/qcom/socinfo.c
index 805dc3c4de40..a473d85bc033 100644
--- a/drivers/soc/qcom/socinfo.c
+++ b/drivers/soc/qcom/socinfo.c
@@ -451,6 +451,7 @@ static const struct soc_id soc_id[] = {
{ qcom_board_id(QCS9100) },
{ qcom_board_id(QCS8300) },
{ qcom_board_id(QCS8275) },
+ { qcom_board_id(QCS9075) },
{ qcom_board_id(QCS615) },
};
--
2.47.0
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v2 3/5] dt-bindings: arm: qcom: Document rb8/ride/ride-r3 on QCS9075
2024-11-15 22:51 [PATCH v2 0/5] arm64: qcom: Add support for QCS9075 boards Wasim Nazir
2024-11-15 22:51 ` [PATCH v2 1/5] dt-bindings: arm: qcom,ids: add SoC ID for QCS9075 Wasim Nazir
2024-11-15 22:51 ` [PATCH v2 2/5] soc: qcom: socinfo: add QCS9075 SoC ID Wasim Nazir
@ 2024-11-15 22:51 ` Wasim Nazir
2024-11-15 22:51 ` [PATCH v2 4/5] arm64: dts: qcom: Add support for QCS9075 RB8 Wasim Nazir
2024-11-15 22:51 ` [PATCH v2 5/5] arm64: dts: qcom: Add support for QCS9075 Ride & Ride-r3 Wasim Nazir
4 siblings, 0 replies; 10+ messages in thread
From: Wasim Nazir @ 2024-11-15 22:51 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel, kernel, Wasim Nazir
qcs9075 rb8, ride & ride-r3 boards are based on QCS9075 SoC.
QCS9075 is compatible IoT-industrial grade variant of SA8775p SoC
without safety monitorng feature of SAfety-IsLand subsystem.
This subsystem continues to supports other features like built-in
self-test, error-detection, reset-handling, etc.
Signed-off-by: Wasim Nazir <quic_wasimn@quicinc.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
---
Documentation/devicetree/bindings/arm/qcom.yaml | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 7c8c3a97506a..de5cf9fb28ae 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -46,6 +46,7 @@ description: |
qcs8550
qcm2290
qcm6490
+ qcs9075
qcs9100
qdu1000
qrb2210
@@ -928,6 +929,14 @@ properties:
- qcom,sa8775p-ride-r3
- const: qcom,sa8775p
+ - items:
+ - enum:
+ - qcom,qcs9075-rb8
+ - qcom,qcs9075-ride
+ - qcom,qcs9075-ride-r3
+ - const: qcom,qcs9075
+ - const: qcom,sa8775p
+
- items:
- enum:
- qcom,qcs9100-ride
--
2.47.0
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v2 4/5] arm64: dts: qcom: Add support for QCS9075 RB8
2024-11-15 22:51 [PATCH v2 0/5] arm64: qcom: Add support for QCS9075 boards Wasim Nazir
` (2 preceding siblings ...)
2024-11-15 22:51 ` [PATCH v2 3/5] dt-bindings: arm: qcom: Document rb8/ride/ride-r3 on QCS9075 Wasim Nazir
@ 2024-11-15 22:51 ` Wasim Nazir
2024-11-15 23:53 ` Dmitry Baryshkov
2024-11-15 22:51 ` [PATCH v2 5/5] arm64: dts: qcom: Add support for QCS9075 Ride & Ride-r3 Wasim Nazir
4 siblings, 1 reply; 10+ messages in thread
From: Wasim Nazir @ 2024-11-15 22:51 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel, kernel, Wasim Nazir
Add device tree support for the QCS9075-RB8 board.
Basic changes are supported for boot to shell.
Signed-off-by: Wasim Nazir <quic_wasimn@quicinc.com>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/qcs9075-rb8.dts | 281 +++++++++++++++++++++++
2 files changed, 282 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/qcs9075-rb8.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 9bb8b191aeb5..5d9847119f2e 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -115,6 +115,7 @@ dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs6490-rb3gen2.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs8550-aim300-aiot.dtb
+dtb-$(CONFIG_ARCH_QCOM) += qcs9075-rb8.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs9100-ride.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs9100-ride-r3.dtb
dtb-$(CONFIG_ARCH_QCOM) += qdu1000-idp.dtb
diff --git a/arch/arm64/boot/dts/qcom/qcs9075-rb8.dts b/arch/arm64/boot/dts/qcom/qcs9075-rb8.dts
new file mode 100644
index 000000000000..e4307ff1e2a7
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/qcs9075-rb8.dts
@@ -0,0 +1,281 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024, Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+#include "sa8775p.dtsi"
+#include "sa8775p-pmics.dtsi"
+
+/ {
+ model = "Qualcomm Technologies, Inc. QCS9075 RB8";
+ compatible = "qcom,qcs9075-rb8", "qcom,qcs9075", "qcom,sa8775p";
+
+ aliases {
+ serial0 = &uart10;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&apps_rsc {
+ regulators-0 {
+ compatible = "qcom,pmm8654au-rpmh-regulators";
+ qcom,pmic-id = "a";
+
+ vreg_s4a: smps4 {
+ regulator-name = "vreg_s4a";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1816000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s5a: smps5 {
+ regulator-name = "vreg_s5a";
+ regulator-min-microvolt = <1850000>;
+ regulator-max-microvolt = <1996000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s9a: smps9 {
+ regulator-name = "vreg_s9a";
+ regulator-min-microvolt = <535000>;
+ regulator-max-microvolt = <1120000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4a: ldo4 {
+ regulator-name = "vreg_l4a";
+ regulator-min-microvolt = <788000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5a: ldo5 {
+ regulator-name = "vreg_l5a";
+ regulator-min-microvolt = <870000>;
+ regulator-max-microvolt = <950000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6a: ldo6 {
+ regulator-name = "vreg_l6a";
+ regulator-min-microvolt = <870000>;
+ regulator-max-microvolt = <970000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7a: ldo7 {
+ regulator-name = "vreg_l7a";
+ regulator-min-microvolt = <720000>;
+ regulator-max-microvolt = <950000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8a: ldo8 {
+ regulator-name = "vreg_l8a";
+ regulator-min-microvolt = <2504000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9a: ldo9 {
+ regulator-name = "vreg_l9a";
+ regulator-min-microvolt = <2970000>;
+ regulator-max-microvolt = <3544000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-1 {
+ compatible = "qcom,pmm8654au-rpmh-regulators";
+ qcom,pmic-id = "c";
+
+ vreg_l1c: ldo1 {
+ regulator-name = "vreg_l1c";
+ regulator-min-microvolt = <1140000>;
+ regulator-max-microvolt = <1260000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2c: ldo2 {
+ regulator-name = "vreg_l2c";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3c: ldo3 {
+ regulator-name = "vreg_l3c";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4c: ldo4 {
+ regulator-name = "vreg_l4c";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ /*
+ * FIXME: This should have regulator-allow-set-load but
+ * we're getting an over-current fault from the PMIC
+ * when switching to LPM.
+ */
+ };
+
+ vreg_l5c: ldo5 {
+ regulator-name = "vreg_l5c";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6c: ldo6 {
+ regulator-name = "vreg_l6c";
+ regulator-min-microvolt = <1620000>;
+ regulator-max-microvolt = <1980000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7c: ldo7 {
+ regulator-name = "vreg_l7c";
+ regulator-min-microvolt = <1620000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8c: ldo8 {
+ regulator-name = "vreg_l8c";
+ regulator-min-microvolt = <2400000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9c: ldo9 {
+ regulator-name = "vreg_l9c";
+ regulator-min-microvolt = <1650000>;
+ regulator-max-microvolt = <2700000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-2 {
+ compatible = "qcom,pmm8654au-rpmh-regulators";
+ qcom,pmic-id = "e";
+
+ vreg_s4e: smps4 {
+ regulator-name = "vreg_s4e";
+ regulator-min-microvolt = <970000>;
+ regulator-max-microvolt = <1520000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s7e: smps7 {
+ regulator-name = "vreg_s7e";
+ regulator-min-microvolt = <1010000>;
+ regulator-max-microvolt = <1170000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s9e: smps9 {
+ regulator-name = "vreg_s9e";
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <570000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6e: ldo6 {
+ regulator-name = "vreg_l6e";
+ regulator-min-microvolt = <1280000>;
+ regulator-max-microvolt = <1450000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8e: ldo8 {
+ regulator-name = "vreg_l8e";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1950000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+};
+
+&qupv3_id_1 {
+ status = "okay";
+};
+
+&sleep_clk {
+ clock-frequency = <32768>;
+};
+
+&tlmm {
+ qup_uart10_default: qup-uart10-state {
+ pins = "gpio46", "gpio47";
+ function = "qup1_se3";
+ };
+};
+
+&uart10 {
+ compatible = "qcom,geni-debug-uart";
+ pinctrl-0 = <&qup_uart10_default>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&xo_board_clk {
+ clock-frequency = <38400000>;
+};
--
2.47.0
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v2 5/5] arm64: dts: qcom: Add support for QCS9075 Ride & Ride-r3
2024-11-15 22:51 [PATCH v2 0/5] arm64: qcom: Add support for QCS9075 boards Wasim Nazir
` (3 preceding siblings ...)
2024-11-15 22:51 ` [PATCH v2 4/5] arm64: dts: qcom: Add support for QCS9075 RB8 Wasim Nazir
@ 2024-11-15 22:51 ` Wasim Nazir
2024-11-15 23:54 ` Dmitry Baryshkov
4 siblings, 1 reply; 10+ messages in thread
From: Wasim Nazir @ 2024-11-15 22:51 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel, kernel, Wasim Nazir
Add device tree support for QCS9075 Ride & Ride-r3 boards.
QCS9075 Ride & Ride-r3 are similar to QCS9100 Ride and Ride-r3
boards but without safety monitoring feature of SAfety-IsLand
subsystem.
Difference between ride and ride-r3 is the ethernet phy.
Ride uses 1G ethernet phy while ride-r3 uses 2.5G ethernet phy.
Signed-off-by: Wasim Nazir <quic_wasimn@quicinc.com>
---
arch/arm64/boot/dts/qcom/Makefile | 2 ++
arch/arm64/boot/dts/qcom/qcs9075-ride-r3.dts | 12 ++++++++++++
arch/arm64/boot/dts/qcom/qcs9075-ride.dts | 12 ++++++++++++
3 files changed, 26 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/qcs9075-ride-r3.dts
create mode 100644 arch/arm64/boot/dts/qcom/qcs9075-ride.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 5d9847119f2e..91c811aca2ca 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -116,6 +116,8 @@ dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs6490-rb3gen2.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs8550-aim300-aiot.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs9075-rb8.dtb
+dtb-$(CONFIG_ARCH_QCOM) += qcs9075-ride.dtb
+dtb-$(CONFIG_ARCH_QCOM) += qcs9075-ride-r3.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs9100-ride.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs9100-ride-r3.dtb
dtb-$(CONFIG_ARCH_QCOM) += qdu1000-idp.dtb
diff --git a/arch/arm64/boot/dts/qcom/qcs9075-ride-r3.dts b/arch/arm64/boot/dts/qcom/qcs9075-ride-r3.dts
new file mode 100644
index 000000000000..a04c8d1fa258
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/qcs9075-ride-r3.dts
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024, Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+/dts-v1/;
+
+#include "sa8775p-ride-r3.dts"
+
+/ {
+ model = "Qualcomm Technologies, Inc. QCS9075 Ride Rev3";
+ compatible = "qcom,qcs9075-ride-r3", "qcom,qcs9075", "qcom,sa8775p";
+};
diff --git a/arch/arm64/boot/dts/qcom/qcs9075-ride.dts b/arch/arm64/boot/dts/qcom/qcs9075-ride.dts
new file mode 100644
index 000000000000..9ffab74fb1a8
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/qcs9075-ride.dts
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024, Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+/dts-v1/;
+
+#include "sa8775p-ride.dts"
+
+/ {
+ model = "Qualcomm Technologies, Inc. QCS9075 Ride";
+ compatible = "qcom,qcs9075-ride", "qcom,qcs9075", "qcom,sa8775p";
+};
--
2.47.0
^ permalink raw reply related [flat|nested] 10+ messages in thread
* Re: [PATCH v2 4/5] arm64: dts: qcom: Add support for QCS9075 RB8
2024-11-15 22:51 ` [PATCH v2 4/5] arm64: dts: qcom: Add support for QCS9075 RB8 Wasim Nazir
@ 2024-11-15 23:53 ` Dmitry Baryshkov
2024-11-19 17:27 ` Wasim Nazir
0 siblings, 1 reply; 10+ messages in thread
From: Dmitry Baryshkov @ 2024-11-15 23:53 UTC (permalink / raw)
To: Wasim Nazir
Cc: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, linux-arm-msm, devicetree, linux-kernel, kernel
On Sat, Nov 16, 2024 at 04:21:51AM +0530, Wasim Nazir wrote:
> Add device tree support for the QCS9075-RB8 board.
>
> Basic changes are supported for boot to shell.
>
> Signed-off-by: Wasim Nazir <quic_wasimn@quicinc.com>
> ---
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> arch/arm64/boot/dts/qcom/qcs9075-rb8.dts | 281 +++++++++++++++++++++++
> 2 files changed, 282 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/qcs9075-rb8.dts
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 9bb8b191aeb5..5d9847119f2e 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -115,6 +115,7 @@ dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qcs6490-rb3gen2.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qcs8550-aim300-aiot.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += qcs9075-rb8.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qcs9100-ride.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qcs9100-ride-r3.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qdu1000-idp.dtb
> diff --git a/arch/arm64/boot/dts/qcom/qcs9075-rb8.dts b/arch/arm64/boot/dts/qcom/qcs9075-rb8.dts
> new file mode 100644
> index 000000000000..e4307ff1e2a7
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/qcs9075-rb8.dts
> @@ -0,0 +1,281 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2024, Qualcomm Innovation Center, Inc. All rights reserved.
> + */
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
> +
> +#include "sa8775p.dtsi"
> +#include "sa8775p-pmics.dtsi"
> +
> +/ {
> + model = "Qualcomm Technologies, Inc. QCS9075 RB8";
Is this going to be an actual product name? Usually RBx boards are named
differently.
> + compatible = "qcom,qcs9075-rb8", "qcom,qcs9075", "qcom,sa8775p";
> +
> + aliases {
> + serial0 = &uart10;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +};
> +
> +&apps_rsc {
> + regulators-0 {
> + compatible = "qcom,pmm8654au-rpmh-regulators";
> + qcom,pmic-id = "a";
> +
> + vreg_s4a: smps4 {
> + regulator-name = "vreg_s4a";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1816000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_s5a: smps5 {
> + regulator-name = "vreg_s5a";
> + regulator-min-microvolt = <1850000>;
> + regulator-max-microvolt = <1996000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_s9a: smps9 {
> + regulator-name = "vreg_s9a";
> + regulator-min-microvolt = <535000>;
> + regulator-max-microvolt = <1120000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l4a: ldo4 {
> + regulator-name = "vreg_l4a";
> + regulator-min-microvolt = <788000>;
> + regulator-max-microvolt = <1050000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l5a: ldo5 {
> + regulator-name = "vreg_l5a";
> + regulator-min-microvolt = <870000>;
> + regulator-max-microvolt = <950000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l6a: ldo6 {
> + regulator-name = "vreg_l6a";
> + regulator-min-microvolt = <870000>;
> + regulator-max-microvolt = <970000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l7a: ldo7 {
> + regulator-name = "vreg_l7a";
> + regulator-min-microvolt = <720000>;
> + regulator-max-microvolt = <950000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l8a: ldo8 {
> + regulator-name = "vreg_l8a";
> + regulator-min-microvolt = <2504000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l9a: ldo9 {
> + regulator-name = "vreg_l9a";
> + regulator-min-microvolt = <2970000>;
> + regulator-max-microvolt = <3544000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> + };
> +
> + regulators-1 {
> + compatible = "qcom,pmm8654au-rpmh-regulators";
> + qcom,pmic-id = "c";
> +
> + vreg_l1c: ldo1 {
> + regulator-name = "vreg_l1c";
> + regulator-min-microvolt = <1140000>;
> + regulator-max-microvolt = <1260000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l2c: ldo2 {
> + regulator-name = "vreg_l2c";
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <1100000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l3c: ldo3 {
> + regulator-name = "vreg_l3c";
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1300000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l4c: ldo4 {
> + regulator-name = "vreg_l4c";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + /*
> + * FIXME: This should have regulator-allow-set-load but
> + * we're getting an over-current fault from the PMIC
> + * when switching to LPM.
> + */
> + };
> +
> + vreg_l5c: ldo5 {
> + regulator-name = "vreg_l5c";
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1300000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l6c: ldo6 {
> + regulator-name = "vreg_l6c";
> + regulator-min-microvolt = <1620000>;
> + regulator-max-microvolt = <1980000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l7c: ldo7 {
> + regulator-name = "vreg_l7c";
> + regulator-min-microvolt = <1620000>;
> + regulator-max-microvolt = <2000000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l8c: ldo8 {
> + regulator-name = "vreg_l8c";
> + regulator-min-microvolt = <2400000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l9c: ldo9 {
> + regulator-name = "vreg_l9c";
> + regulator-min-microvolt = <1650000>;
> + regulator-max-microvolt = <2700000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> + };
> +
> + regulators-2 {
> + compatible = "qcom,pmm8654au-rpmh-regulators";
> + qcom,pmic-id = "e";
> +
> + vreg_s4e: smps4 {
> + regulator-name = "vreg_s4e";
> + regulator-min-microvolt = <970000>;
> + regulator-max-microvolt = <1520000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_s7e: smps7 {
> + regulator-name = "vreg_s7e";
> + regulator-min-microvolt = <1010000>;
> + regulator-max-microvolt = <1170000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_s9e: smps9 {
> + regulator-name = "vreg_s9e";
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <570000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l6e: ldo6 {
> + regulator-name = "vreg_l6e";
> + regulator-min-microvolt = <1280000>;
> + regulator-max-microvolt = <1450000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l8e: ldo8 {
> + regulator-name = "vreg_l8e";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1950000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> + };
> +};
> +
> +&qupv3_id_1 {
> + status = "okay";
> +};
> +
> +&sleep_clk {
> + clock-frequency = <32768>;
> +};
> +
> +&tlmm {
> + qup_uart10_default: qup-uart10-state {
> + pins = "gpio46", "gpio47";
> + function = "qup1_se3";
> + };
> +};
> +
> +&uart10 {
> + compatible = "qcom,geni-debug-uart";
> + pinctrl-0 = <&qup_uart10_default>;
> + pinctrl-names = "default";
> + status = "okay";
> +};
> +
> +&xo_board_clk {
> + clock-frequency = <38400000>;
> +};
> --
> 2.47.0
>
--
With best wishes
Dmitry
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH v2 5/5] arm64: dts: qcom: Add support for QCS9075 Ride & Ride-r3
2024-11-15 22:51 ` [PATCH v2 5/5] arm64: dts: qcom: Add support for QCS9075 Ride & Ride-r3 Wasim Nazir
@ 2024-11-15 23:54 ` Dmitry Baryshkov
2024-11-19 17:38 ` Wasim Nazir
0 siblings, 1 reply; 10+ messages in thread
From: Dmitry Baryshkov @ 2024-11-15 23:54 UTC (permalink / raw)
To: Wasim Nazir
Cc: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, linux-arm-msm, devicetree, linux-kernel, kernel
On Sat, Nov 16, 2024 at 04:21:52AM +0530, Wasim Nazir wrote:
> Add device tree support for QCS9075 Ride & Ride-r3 boards.
> QCS9075 Ride & Ride-r3 are similar to QCS9100 Ride and Ride-r3
> boards but without safety monitoring feature of SAfety-IsLand
> subsystem.
Why do we need another set of DTS files? Should we expect more changes
to these DTS files?
>
> Difference between ride and ride-r3 is the ethernet phy.
> Ride uses 1G ethernet phy while ride-r3 uses 2.5G ethernet phy.
>
> Signed-off-by: Wasim Nazir <quic_wasimn@quicinc.com>
> ---
> arch/arm64/boot/dts/qcom/Makefile | 2 ++
> arch/arm64/boot/dts/qcom/qcs9075-ride-r3.dts | 12 ++++++++++++
> arch/arm64/boot/dts/qcom/qcs9075-ride.dts | 12 ++++++++++++
> 3 files changed, 26 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/qcs9075-ride-r3.dts
> create mode 100644 arch/arm64/boot/dts/qcom/qcs9075-ride.dts
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 5d9847119f2e..91c811aca2ca 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -116,6 +116,8 @@ dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qcs6490-rb3gen2.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qcs8550-aim300-aiot.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qcs9075-rb8.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += qcs9075-ride.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += qcs9075-ride-r3.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qcs9100-ride.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qcs9100-ride-r3.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qdu1000-idp.dtb
> diff --git a/arch/arm64/boot/dts/qcom/qcs9075-ride-r3.dts b/arch/arm64/boot/dts/qcom/qcs9075-ride-r3.dts
> new file mode 100644
> index 000000000000..a04c8d1fa258
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/qcs9075-ride-r3.dts
> @@ -0,0 +1,12 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2024, Qualcomm Innovation Center, Inc. All rights reserved.
> + */
> +/dts-v1/;
> +
> +#include "sa8775p-ride-r3.dts"
> +
> +/ {
> + model = "Qualcomm Technologies, Inc. QCS9075 Ride Rev3";
> + compatible = "qcom,qcs9075-ride-r3", "qcom,qcs9075", "qcom,sa8775p";
> +};
> diff --git a/arch/arm64/boot/dts/qcom/qcs9075-ride.dts b/arch/arm64/boot/dts/qcom/qcs9075-ride.dts
> new file mode 100644
> index 000000000000..9ffab74fb1a8
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/qcs9075-ride.dts
> @@ -0,0 +1,12 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2024, Qualcomm Innovation Center, Inc. All rights reserved.
> + */
> +/dts-v1/;
> +
> +#include "sa8775p-ride.dts"
> +
> +/ {
> + model = "Qualcomm Technologies, Inc. QCS9075 Ride";
> + compatible = "qcom,qcs9075-ride", "qcom,qcs9075", "qcom,sa8775p";
> +};
> --
> 2.47.0
>
--
With best wishes
Dmitry
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH v2 4/5] arm64: dts: qcom: Add support for QCS9075 RB8
2024-11-15 23:53 ` Dmitry Baryshkov
@ 2024-11-19 17:27 ` Wasim Nazir
0 siblings, 0 replies; 10+ messages in thread
From: Wasim Nazir @ 2024-11-19 17:27 UTC (permalink / raw)
To: Dmitry Baryshkov
Cc: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, linux-arm-msm, devicetree, linux-kernel, kernel
On Sat, Nov 16, 2024 at 01:53:00AM +0200, Dmitry Baryshkov wrote:
> On Sat, Nov 16, 2024 at 04:21:51AM +0530, Wasim Nazir wrote:
> > Add device tree support for the QCS9075-RB8 board.
> >
> > Basic changes are supported for boot to shell.
> >
> > Signed-off-by: Wasim Nazir <quic_wasimn@quicinc.com>
> > ---
> > arch/arm64/boot/dts/qcom/Makefile | 1 +
> > arch/arm64/boot/dts/qcom/qcs9075-rb8.dts | 281 +++++++++++++++++++++++
> > 2 files changed, 282 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/qcom/qcs9075-rb8.dts
> >
> > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> > index 9bb8b191aeb5..5d9847119f2e 100644
> > --- a/arch/arm64/boot/dts/qcom/Makefile
> > +++ b/arch/arm64/boot/dts/qcom/Makefile
> > @@ -115,6 +115,7 @@ dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb
> > dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
> > dtb-$(CONFIG_ARCH_QCOM) += qcs6490-rb3gen2.dtb
> > dtb-$(CONFIG_ARCH_QCOM) += qcs8550-aim300-aiot.dtb
> > +dtb-$(CONFIG_ARCH_QCOM) += qcs9075-rb8.dtb
> > dtb-$(CONFIG_ARCH_QCOM) += qcs9100-ride.dtb
> > dtb-$(CONFIG_ARCH_QCOM) += qcs9100-ride-r3.dtb
> > dtb-$(CONFIG_ARCH_QCOM) += qdu1000-idp.dtb
> > diff --git a/arch/arm64/boot/dts/qcom/qcs9075-rb8.dts b/arch/arm64/boot/dts/qcom/qcs9075-rb8.dts
> > new file mode 100644
> > index 000000000000..e4307ff1e2a7
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/qcom/qcs9075-rb8.dts
> > @@ -0,0 +1,281 @@
> > +// SPDX-License-Identifier: BSD-3-Clause
> > +/*
> > + * Copyright (c) 2024, Qualcomm Innovation Center, Inc. All rights reserved.
> > + */
> > +/dts-v1/;
> > +
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
> > +
> > +#include "sa8775p.dtsi"
> > +#include "sa8775p-pmics.dtsi"
> > +
> > +/ {
> > + model = "Qualcomm Technologies, Inc. QCS9075 RB8";
>
> Is this going to be an actual product name? Usually RBx boards are named
> differently.
Will update it in next series.
>
> > + compatible = "qcom,qcs9075-rb8", "qcom,qcs9075", "qcom,sa8775p";
> > +
> > + aliases {
> > + serial0 = &uart10;
> > + };
> > +
> > + chosen {
> > + stdout-path = "serial0:115200n8";
> > + };
> > +};
> > +
> > +&apps_rsc {
> > + regulators-0 {
> > + compatible = "qcom,pmm8654au-rpmh-regulators";
> > + qcom,pmic-id = "a";
> > +
> > + vreg_s4a: smps4 {
> > + regulator-name = "vreg_s4a";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1816000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_s5a: smps5 {
> > + regulator-name = "vreg_s5a";
> > + regulator-min-microvolt = <1850000>;
> > + regulator-max-microvolt = <1996000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_s9a: smps9 {
> > + regulator-name = "vreg_s9a";
> > + regulator-min-microvolt = <535000>;
> > + regulator-max-microvolt = <1120000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_l4a: ldo4 {
> > + regulator-name = "vreg_l4a";
> > + regulator-min-microvolt = <788000>;
> > + regulator-max-microvolt = <1050000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + regulator-allow-set-load;
> > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> > + RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_l5a: ldo5 {
> > + regulator-name = "vreg_l5a";
> > + regulator-min-microvolt = <870000>;
> > + regulator-max-microvolt = <950000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + regulator-allow-set-load;
> > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> > + RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_l6a: ldo6 {
> > + regulator-name = "vreg_l6a";
> > + regulator-min-microvolt = <870000>;
> > + regulator-max-microvolt = <970000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + regulator-allow-set-load;
> > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> > + RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_l7a: ldo7 {
> > + regulator-name = "vreg_l7a";
> > + regulator-min-microvolt = <720000>;
> > + regulator-max-microvolt = <950000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + regulator-allow-set-load;
> > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> > + RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_l8a: ldo8 {
> > + regulator-name = "vreg_l8a";
> > + regulator-min-microvolt = <2504000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + regulator-allow-set-load;
> > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> > + RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_l9a: ldo9 {
> > + regulator-name = "vreg_l9a";
> > + regulator-min-microvolt = <2970000>;
> > + regulator-max-microvolt = <3544000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + regulator-allow-set-load;
> > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> > + RPMH_REGULATOR_MODE_HPM>;
> > + };
> > + };
> > +
> > + regulators-1 {
> > + compatible = "qcom,pmm8654au-rpmh-regulators";
> > + qcom,pmic-id = "c";
> > +
> > + vreg_l1c: ldo1 {
> > + regulator-name = "vreg_l1c";
> > + regulator-min-microvolt = <1140000>;
> > + regulator-max-microvolt = <1260000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + regulator-allow-set-load;
> > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> > + RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_l2c: ldo2 {
> > + regulator-name = "vreg_l2c";
> > + regulator-min-microvolt = <900000>;
> > + regulator-max-microvolt = <1100000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + regulator-allow-set-load;
> > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> > + RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_l3c: ldo3 {
> > + regulator-name = "vreg_l3c";
> > + regulator-min-microvolt = <1100000>;
> > + regulator-max-microvolt = <1300000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + regulator-allow-set-load;
> > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> > + RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_l4c: ldo4 {
> > + regulator-name = "vreg_l4c";
> > + regulator-min-microvolt = <1200000>;
> > + regulator-max-microvolt = <1200000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + /*
> > + * FIXME: This should have regulator-allow-set-load but
> > + * we're getting an over-current fault from the PMIC
> > + * when switching to LPM.
> > + */
> > + };
> > +
> > + vreg_l5c: ldo5 {
> > + regulator-name = "vreg_l5c";
> > + regulator-min-microvolt = <1100000>;
> > + regulator-max-microvolt = <1300000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + regulator-allow-set-load;
> > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> > + RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_l6c: ldo6 {
> > + regulator-name = "vreg_l6c";
> > + regulator-min-microvolt = <1620000>;
> > + regulator-max-microvolt = <1980000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + regulator-allow-set-load;
> > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> > + RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_l7c: ldo7 {
> > + regulator-name = "vreg_l7c";
> > + regulator-min-microvolt = <1620000>;
> > + regulator-max-microvolt = <2000000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + regulator-allow-set-load;
> > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> > + RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_l8c: ldo8 {
> > + regulator-name = "vreg_l8c";
> > + regulator-min-microvolt = <2400000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + regulator-allow-set-load;
> > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> > + RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_l9c: ldo9 {
> > + regulator-name = "vreg_l9c";
> > + regulator-min-microvolt = <1650000>;
> > + regulator-max-microvolt = <2700000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + regulator-allow-set-load;
> > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> > + RPMH_REGULATOR_MODE_HPM>;
> > + };
> > + };
> > +
> > + regulators-2 {
> > + compatible = "qcom,pmm8654au-rpmh-regulators";
> > + qcom,pmic-id = "e";
> > +
> > + vreg_s4e: smps4 {
> > + regulator-name = "vreg_s4e";
> > + regulator-min-microvolt = <970000>;
> > + regulator-max-microvolt = <1520000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_s7e: smps7 {
> > + regulator-name = "vreg_s7e";
> > + regulator-min-microvolt = <1010000>;
> > + regulator-max-microvolt = <1170000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_s9e: smps9 {
> > + regulator-name = "vreg_s9e";
> > + regulator-min-microvolt = <300000>;
> > + regulator-max-microvolt = <570000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_l6e: ldo6 {
> > + regulator-name = "vreg_l6e";
> > + regulator-min-microvolt = <1280000>;
> > + regulator-max-microvolt = <1450000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + regulator-allow-set-load;
> > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> > + RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_l8e: ldo8 {
> > + regulator-name = "vreg_l8e";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1950000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + regulator-allow-set-load;
> > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> > + RPMH_REGULATOR_MODE_HPM>;
> > + };
> > + };
> > +};
> > +
> > +&qupv3_id_1 {
> > + status = "okay";
> > +};
> > +
> > +&sleep_clk {
> > + clock-frequency = <32768>;
> > +};
> > +
> > +&tlmm {
> > + qup_uart10_default: qup-uart10-state {
> > + pins = "gpio46", "gpio47";
> > + function = "qup1_se3";
> > + };
> > +};
> > +
> > +&uart10 {
> > + compatible = "qcom,geni-debug-uart";
> > + pinctrl-0 = <&qup_uart10_default>;
> > + pinctrl-names = "default";
> > + status = "okay";
> > +};
> > +
> > +&xo_board_clk {
> > + clock-frequency = <38400000>;
> > +};
> > --
> > 2.47.0
> >
>
> --
> With best wishes
> Dmitry
Thanks & Regards,
Wasim
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH v2 5/5] arm64: dts: qcom: Add support for QCS9075 Ride & Ride-r3
2024-11-15 23:54 ` Dmitry Baryshkov
@ 2024-11-19 17:38 ` Wasim Nazir
0 siblings, 0 replies; 10+ messages in thread
From: Wasim Nazir @ 2024-11-19 17:38 UTC (permalink / raw)
To: Dmitry Baryshkov
Cc: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, linux-arm-msm, devicetree, linux-kernel, kernel
On Sat, Nov 16, 2024 at 01:54:23AM +0200, Dmitry Baryshkov wrote:
> On Sat, Nov 16, 2024 at 04:21:52AM +0530, Wasim Nazir wrote:
> > Add device tree support for QCS9075 Ride & Ride-r3 boards.
> > QCS9075 Ride & Ride-r3 are similar to QCS9100 Ride and Ride-r3
> > boards but without safety monitoring feature of SAfety-IsLand
> > subsystem.
>
> Why do we need another set of DTS files? Should we expect more changes
> to these DTS files?
Ride/r3 based on qcs9075 and qcs9100 are 4 different boards with different
SoCs, so different file is used to represent all the 4 boards.
>
> >
> > Difference between ride and ride-r3 is the ethernet phy.
> > Ride uses 1G ethernet phy while ride-r3 uses 2.5G ethernet phy.
> >
> > Signed-off-by: Wasim Nazir <quic_wasimn@quicinc.com>
> > ---
> > arch/arm64/boot/dts/qcom/Makefile | 2 ++
> > arch/arm64/boot/dts/qcom/qcs9075-ride-r3.dts | 12 ++++++++++++
> > arch/arm64/boot/dts/qcom/qcs9075-ride.dts | 12 ++++++++++++
> > 3 files changed, 26 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/qcom/qcs9075-ride-r3.dts
> > create mode 100644 arch/arm64/boot/dts/qcom/qcs9075-ride.dts
> >
> > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> > index 5d9847119f2e..91c811aca2ca 100644
> > --- a/arch/arm64/boot/dts/qcom/Makefile
> > +++ b/arch/arm64/boot/dts/qcom/Makefile
> > @@ -116,6 +116,8 @@ dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
> > dtb-$(CONFIG_ARCH_QCOM) += qcs6490-rb3gen2.dtb
> > dtb-$(CONFIG_ARCH_QCOM) += qcs8550-aim300-aiot.dtb
> > dtb-$(CONFIG_ARCH_QCOM) += qcs9075-rb8.dtb
> > +dtb-$(CONFIG_ARCH_QCOM) += qcs9075-ride.dtb
> > +dtb-$(CONFIG_ARCH_QCOM) += qcs9075-ride-r3.dtb
> > dtb-$(CONFIG_ARCH_QCOM) += qcs9100-ride.dtb
> > dtb-$(CONFIG_ARCH_QCOM) += qcs9100-ride-r3.dtb
> > dtb-$(CONFIG_ARCH_QCOM) += qdu1000-idp.dtb
> > diff --git a/arch/arm64/boot/dts/qcom/qcs9075-ride-r3.dts b/arch/arm64/boot/dts/qcom/qcs9075-ride-r3.dts
> > new file mode 100644
> > index 000000000000..a04c8d1fa258
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/qcom/qcs9075-ride-r3.dts
> > @@ -0,0 +1,12 @@
> > +// SPDX-License-Identifier: BSD-3-Clause
> > +/*
> > + * Copyright (c) 2024, Qualcomm Innovation Center, Inc. All rights reserved.
> > + */
> > +/dts-v1/;
> > +
> > +#include "sa8775p-ride-r3.dts"
> > +
> > +/ {
> > + model = "Qualcomm Technologies, Inc. QCS9075 Ride Rev3";
> > + compatible = "qcom,qcs9075-ride-r3", "qcom,qcs9075", "qcom,sa8775p";
> > +};
> > diff --git a/arch/arm64/boot/dts/qcom/qcs9075-ride.dts b/arch/arm64/boot/dts/qcom/qcs9075-ride.dts
> > new file mode 100644
> > index 000000000000..9ffab74fb1a8
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/qcom/qcs9075-ride.dts
> > @@ -0,0 +1,12 @@
> > +// SPDX-License-Identifier: BSD-3-Clause
> > +/*
> > + * Copyright (c) 2024, Qualcomm Innovation Center, Inc. All rights reserved.
> > + */
> > +/dts-v1/;
> > +
> > +#include "sa8775p-ride.dts"
> > +
> > +/ {
> > + model = "Qualcomm Technologies, Inc. QCS9075 Ride";
> > + compatible = "qcom,qcs9075-ride", "qcom,qcs9075", "qcom,sa8775p";
> > +};
> > --
> > 2.47.0
> >
>
> --
> With best wishes
> Dmitry
Thanks & Regards,
Wasim
^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2024-11-19 17:38 UTC | newest]
Thread overview: 10+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2024-11-15 22:51 [PATCH v2 0/5] arm64: qcom: Add support for QCS9075 boards Wasim Nazir
2024-11-15 22:51 ` [PATCH v2 1/5] dt-bindings: arm: qcom,ids: add SoC ID for QCS9075 Wasim Nazir
2024-11-15 22:51 ` [PATCH v2 2/5] soc: qcom: socinfo: add QCS9075 SoC ID Wasim Nazir
2024-11-15 22:51 ` [PATCH v2 3/5] dt-bindings: arm: qcom: Document rb8/ride/ride-r3 on QCS9075 Wasim Nazir
2024-11-15 22:51 ` [PATCH v2 4/5] arm64: dts: qcom: Add support for QCS9075 RB8 Wasim Nazir
2024-11-15 23:53 ` Dmitry Baryshkov
2024-11-19 17:27 ` Wasim Nazir
2024-11-15 22:51 ` [PATCH v2 5/5] arm64: dts: qcom: Add support for QCS9075 Ride & Ride-r3 Wasim Nazir
2024-11-15 23:54 ` Dmitry Baryshkov
2024-11-19 17:38 ` Wasim Nazir
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox