[PATCH v7 0/5] I2C Mux per channel bus speed

[PATCH v7 0/5] I2C Mux per channel bus speed

[Marcus Folkesson]

This was a RFC on how to implement a feature to have different bus
speeds on different channels with an I2C multiplexer/switch.
As no major complaints on the design came up during the review, I
decided to submit the series without the RFC tag.

The benefit with this feature is that you may group devices after
the fastest bus speed they can handle.
A real-world example is that you could have e.g. a display running @400kHz
and a smart battery running @100kHz using the same I2C controller.

There are many corner cases where this may cause a problem for some
hardware topologies. I've tried to describe those I could think of
in the documentation, see Patch #5.

E.g. one risk is that if the mux driver does not disconnect channels
when Idle, this may cause a higher frequency to "leak" through to
devices that are supposed to run at lower bus speed.
This is not only a "problem" for changing bus speed but could also be
an issue for potential address conflicts.

This patchset has been used and tested heavily the last months
on a custom board based on a da850 (DaVinci) platform.

The implementation is split up into several patches:

Patch #1 Introduce a callback for the i2c controller to set bus speed
Patch #2 Introduce functionality to adjust bus speed depending on mux
         channel.
Patch #3 Cleanup i2c-davinci driver a bit to prepare it for set_clk_freq
Parch #4 Implement set_clk_freq for the i2c-davinci driver
Parch #5 Update documentation with this feature

Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
---
Changes in v7:
- Remove code for finding first mux-locked ancestor
- Introduce a unlocked (i2c_adapter_set_clk_freq) and unlocked
  (__i2c_adapter_set_clk_freq) variant
- Let the locking be handled in __i2c_adapter_set_clk_freq
- Use I2C_MAX_STANDARD_MODE_FREQ instead of magic numbers where
  appropriate 
- Link to v6: https://lore.kernel.org/r/20260216-i2c-mux-v6-0-9be28ecfd7e3@gmail.com

Changes in v6:
- Change logic to find which ancestor to lock with I2C_LOCK_ROOT_ADAPTER
  It now find the first mux-locked ancestor and then lock its parent.

- Remove bus_freq_hz in i2c-davinci and only use clock_hz instead
- Mention in commit message that clock_hz can be used to store frequency in an uniform way

- Swap order for change freq/deselect to keep symmetry
- Only allow bus frequency to be lowered in select()
  This to not allow an intermediate frequency to be set when it is not
  supposed to

- check if(ret) instead of ret(<0) where appropriate
- Fix typos in documentation
- Change i2c_adapter.clock_hz from int to u32
- Simplify i2c_adapter_set_clk_freq() by removing 'ret'
- Link to v5: https://lore.kernel.org/r/20260213-i2c-mux-v5-0-fb2cbf9979b3@gmail.com

Changes in v5:
- Take the lock of the top-most mutex locked mux to make sure that the
  root is locked
- Link to v4: https://lore.kernel.org/r/20260128-i2c-mux-v4-0-dee49ce276c0@gmail.com

Changes in v4:
- Rebase on master
- Swap order for printing warning about "channel %u is slower than
  parent on a non parent-locked mux\n"
- Fix typo in comment, adaper->adapter
- Link to v3: https://lore.kernel.org/r/20251020-i2c-mux-v3-0-908ac5cf9223@gmail.com

Changes in v3:
- Return -EINVAL if channel is faster than parent (kernel test robot)
- Link to v2: https://lore.kernel.org/r/20251002-i2c-mux-v2-0-b698564cd956@gmail.com

Changes in v2:
- Changed bus_freq field to bus_freq_hz in davinci_i2c_dev (Bartosz Golaszewski)
- Removed idle_state from mux core (Peter Rosin)
- Link to v1: https://lore.kernel.org/r/20250922-i2c-mux-v1-0-28c94a610930@gmail.com

---
Marcus Folkesson (5):
      i2c: core: add callback to change bus frequency
      i2c: mux: add support for per channel bus frequency
      i2c: davinci: calculate bus freq from Hz instead of kHz
      i2c: davinci: add support for setting bus frequency
      docs: i2c: i2c-topology: add section about bus speed

 Documentation/i2c/i2c-topology.rst | 178 +++++++++++++++++++++++++++++++++++++
 drivers/i2c/busses/i2c-davinci.c   |  42 ++++++---
 drivers/i2c/i2c-mux.c              | 107 +++++++++++++++++++---
 include/linux/i2c.h                |  34 +++++++
 4 files changed, 338 insertions(+), 23 deletions(-)
---
base-commit: 1f97d9dcf53649c41c33227b345a36902cbb08ad
change-id: 20250913-i2c-mux-b0063de2ae4d

Best regards,
-- 
Marcus Folkesson <marcus.folkesson@gmail.com>

[PATCH v7 1/5] i2c: core: add callback to change bus frequency

[Marcus Folkesson]

All devices on the same I2C bus share the same clock line and the bus
frequency has therefor be chosen so that all attached devices are able
to tolarate that clock rate. IOW, the bus speed must be set for the
slowest attached device.

With I2C multiplexers/switches on the other hand, it would be possible
to have different "domains" that runs with different speeds.

Prepare for such a feature by provide an optional callback function to
change bus frequency.

As a side effect, several bus drivers keep the bus speed in a
private structure and can now have this value stored in a uniform way
instead.

Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
---
 include/linux/i2c.h | 34 ++++++++++++++++++++++++++++++++++
 1 file changed, 34 insertions(+)

diff --git a/include/linux/i2c.h b/include/linux/i2c.h
index 20fd41b51d5c..f81decb3f1f7 100644
--- a/include/linux/i2c.h
+++ b/include/linux/i2c.h
@@ -742,6 +742,8 @@ struct i2c_adapter {
 	struct rt_mutex mux_lock;
 
 	int timeout;			/* in jiffies */
+	u32 clock_hz;			/* bus clock speed */
+	int (*set_clk_freq)(struct i2c_adapter *adap, u32 clock_hz); /* Optional */
 	int retries;
 	struct device dev;		/* the adapter device */
 	unsigned long locked_flags;	/* owned by the I2C core */
@@ -835,6 +837,38 @@ i2c_unlock_bus(struct i2c_adapter *adapter, unsigned int flags)
 	adapter->lock_ops->unlock_bus(adapter, flags);
 }
 
+static inline int
+__i2c_adapter_set_clk_freq(struct i2c_adapter *adapter, u32 clock_hz)
+{
+	if (adapter->set_clk_freq)
+		return adapter->set_clk_freq(adapter, clock_hz);
+
+	/*
+	 * If the adapter is a root adapter without set_clk_freq implemented, this feature is not
+	 * supported
+	 */
+	if (!i2c_parent_is_i2c_adapter(adapter))
+		return -EOPNOTSUPP;
+
+	/* Update the clock_hz for non-root adapters, even if set_clk_freq is not implemented,
+	 * to allow * the clock frequency to be propagated to root adapters that do support it.
+	 */
+	adapter->clock_hz = clock_hz;
+	return 0;
+}
+
+static inline int
+i2c_adapter_set_clk_freq(struct i2c_adapter *adapter, u32 clock_hz)
+{
+	int ret;
+
+	i2c_lock_bus(adapter, I2C_LOCK_SEGMENT);
+	ret = __i2c_adapter_set_clk_freq(adapter, clock_hz);
+	i2c_unlock_bus(adapter, I2C_LOCK_SEGMENT);
+
+	return ret;
+}
+
 /**
  * i2c_mark_adapter_suspended - Report suspended state of the adapter to the core
  * @adap: Adapter to mark as suspended

-- 
2.52.0

[PATCH v7 2/5] i2c: mux: add support for per channel bus frequency

[Marcus Folkesson]

There may be several reasons why you may need to use a certain speed
on an I2C bus. E.g.

- When several devices are attached to the bus, the speed must be
  selected according to the slowest device.

- Electrical conditions may limit the usuable speed on the bus for
  different reasons.

With an I2C multiplexer, it is possible to group the attached devices
after their preferred speed by e.g. put all "slow" devices on a separate
channel on the multiplexer.

Consider the following topology:

                      .----------. 100kHz .--------.
    .--------. 400kHz |          |--------| dev D1 |
    |  root  |--+-----| I2C MUX  |        '--------'
    '--------'  |     |          |--. 400kHz .--------.
                |     '----------'  '-------| dev D2 |
                |  .--------.               '--------'
                '--| dev D3 |
                   '--------'

One requirement with this design is that a multiplexer may only use the
same or lower bus speed as its parent.
Otherwise, if the multiplexer would have to increase the bus frequency,
then all siblings (D3 in this case) would run into a clock speed it may
not support.

The bus frequency for each channel is set in the devicetree. As the
i2c-mux bindings import the i2c-controller schema, the clock-frequency
property is already allowed.
If no clock-frequency property is set, the channel inherit their parent
bus speed.

The following example uses dt bindings to illustrate the topology above:

    i2c {
	clock-frequency = <400000>;

        i2c-mux {
            i2c@0 {
                clock-frequency = <100000>;

                D1 {
                    ...
                };
            };

            i2c@1 {
                D2 {
                  ...
                };
            };
        };

        D3 {
            ...
        }
    };

Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
---
 drivers/i2c/i2c-mux.c | 107 ++++++++++++++++++++++++++++++++++++++++++++------
 1 file changed, 95 insertions(+), 12 deletions(-)

diff --git a/drivers/i2c/i2c-mux.c b/drivers/i2c/i2c-mux.c
index d59644e50f14..df18930d6ed4 100644
--- a/drivers/i2c/i2c-mux.c
+++ b/drivers/i2c/i2c-mux.c
@@ -36,21 +36,75 @@ struct i2c_mux_priv {
 	u32 chan_id;
 };
 
+static int i2c_mux_select_chan(struct i2c_adapter *adap, u32 chan_id, u32 *oldclock)
+{
+	struct i2c_mux_priv *priv = adap->algo_data;
+	struct i2c_mux_core *muxc = priv->muxc;
+	struct i2c_adapter *parent = muxc->parent;
+	int ret;
+
+	if (priv->adap.clock_hz && priv->adap.clock_hz < parent->clock_hz) {
+		*oldclock = parent->clock_hz;
+
+		if (muxc->mux_locked)
+			ret = i2c_adapter_set_clk_freq(parent, priv->adap.clock_hz);
+		else
+			ret = __i2c_adapter_set_clk_freq(parent, priv->adap.clock_hz);
+
+		dev_dbg(&adap->dev, "Set clock frequency %dHz on %s\n",
+			priv->adap.clock_hz, parent->name);
+
+		if (ret)
+			dev_err(&adap->dev,
+				"Failed to set clock frequency %dHz on adapter %s: %d\n",
+				*oldclock, parent->name, ret);
+	}
+
+	return muxc->select(muxc, priv->chan_id);
+}
+
+static void i2c_mux_deselect_chan(struct i2c_adapter *adap, u32 chan_id, u32 oldclock)
+{
+	struct i2c_mux_priv *priv = adap->algo_data;
+	struct i2c_mux_core *muxc = priv->muxc;
+	struct i2c_adapter *parent = muxc->parent;
+	int ret;
+
+	if (muxc->deselect)
+		muxc->deselect(muxc, priv->chan_id);
+
+	if (oldclock && oldclock != priv->adap.clock_hz) {
+		if (muxc->mux_locked)
+			ret = i2c_adapter_set_clk_freq(parent, oldclock);
+		else
+			ret = __i2c_adapter_set_clk_freq(parent, oldclock);
+
+		dev_dbg(&adap->dev, "Restored clock frequency %dHz on %s\n",
+			oldclock, parent->name);
+
+		if (ret)
+			dev_err(&adap->dev,
+				"Failed to set clock frequency %dHz on adapter %s: %d\n",
+				oldclock, parent->name, ret);
+	}
+}
+
 static int __i2c_mux_master_xfer(struct i2c_adapter *adap,
 				 struct i2c_msg msgs[], int num)
 {
 	struct i2c_mux_priv *priv = adap->algo_data;
 	struct i2c_mux_core *muxc = priv->muxc;
 	struct i2c_adapter *parent = muxc->parent;
+	u32 oldclock = 0;
 	int ret;
 
 	/* Switch to the right mux port and perform the transfer. */
 
-	ret = muxc->select(muxc, priv->chan_id);
+	ret = i2c_mux_select_chan(adap, priv->chan_id, &oldclock);
 	if (ret >= 0)
 		ret = __i2c_transfer(parent, msgs, num);
-	if (muxc->deselect)
-		muxc->deselect(muxc, priv->chan_id);
+
+	i2c_mux_deselect_chan(adap, priv->chan_id, oldclock);
 
 	return ret;
 }
@@ -61,15 +115,16 @@ static int i2c_mux_master_xfer(struct i2c_adapter *adap,
 	struct i2c_mux_priv *priv = adap->algo_data;
 	struct i2c_mux_core *muxc = priv->muxc;
 	struct i2c_adapter *parent = muxc->parent;
+	u32 oldclock = 0;
 	int ret;
 
 	/* Switch to the right mux port and perform the transfer. */
 
-	ret = muxc->select(muxc, priv->chan_id);
+	ret = i2c_mux_select_chan(adap, priv->chan_id, &oldclock);
 	if (ret >= 0)
 		ret = i2c_transfer(parent, msgs, num);
-	if (muxc->deselect)
-		muxc->deselect(muxc, priv->chan_id);
+
+	i2c_mux_deselect_chan(adap, priv->chan_id, oldclock);
 
 	return ret;
 }
@@ -82,16 +137,17 @@ static int __i2c_mux_smbus_xfer(struct i2c_adapter *adap,
 	struct i2c_mux_priv *priv = adap->algo_data;
 	struct i2c_mux_core *muxc = priv->muxc;
 	struct i2c_adapter *parent = muxc->parent;
+	u32 oldclock = 0;
 	int ret;
 
 	/* Select the right mux port and perform the transfer. */
 
-	ret = muxc->select(muxc, priv->chan_id);
+	ret = i2c_mux_select_chan(adap, priv->chan_id, &oldclock);
 	if (ret >= 0)
 		ret = __i2c_smbus_xfer(parent, addr, flags,
 				       read_write, command, size, data);
-	if (muxc->deselect)
-		muxc->deselect(muxc, priv->chan_id);
+
+	i2c_mux_deselect_chan(adap, priv->chan_id, oldclock);
 
 	return ret;
 }
@@ -104,16 +160,17 @@ static int i2c_mux_smbus_xfer(struct i2c_adapter *adap,
 	struct i2c_mux_priv *priv = adap->algo_data;
 	struct i2c_mux_core *muxc = priv->muxc;
 	struct i2c_adapter *parent = muxc->parent;
+	u32 oldclock = 0;
 	int ret;
 
 	/* Select the right mux port and perform the transfer. */
 
-	ret = muxc->select(muxc, priv->chan_id);
+	ret = i2c_mux_select_chan(adap, priv->chan_id, &oldclock);
 	if (ret >= 0)
 		ret = i2c_smbus_xfer(parent, addr, flags,
 				     read_write, command, size, data);
-	if (muxc->deselect)
-		muxc->deselect(muxc, priv->chan_id);
+
+	i2c_mux_deselect_chan(adap, priv->chan_id, oldclock);
 
 	return ret;
 }
@@ -362,6 +419,32 @@ int i2c_mux_add_adapter(struct i2c_mux_core *muxc,
 			}
 		}
 
+		of_property_read_u32(child, "clock-frequency", &priv->adap.clock_hz);
+
+		/* If the mux adapter has no clock-frequency property, inherit from parent */
+		if (!priv->adap.clock_hz)
+			priv->adap.clock_hz = parent->clock_hz;
+
+		/*
+		 * Warn if the mux adapter is not parent-locked as
+		 * this may cause issues for some hardware topologies.
+		 */
+		if ((priv->adap.clock_hz < parent->clock_hz) && muxc->mux_locked)
+			dev_warn(muxc->dev,
+				 "channel %u is slower than parent on a non parent-locked mux\n",
+				 chan_id);
+
+		/* We don't support mux adapters faster than their parent */
+		if (priv->adap.clock_hz > parent->clock_hz) {
+			dev_err(muxc->dev,
+				"channel (%u) is faster (%u) than parent (%u)\n",
+				chan_id, priv->adap.clock_hz, parent->clock_hz);
+
+			of_node_put(mux_node);
+			ret = -EINVAL;
+			goto err_free_priv;
+		}
+
 		priv->adap.dev.of_node = child;
 		of_node_put(mux_node);
 	}

-- 
2.52.0

[PATCH v7 3/5] i2c: davinci: calculate bus freq from Hz instead of kHz

[Marcus Folkesson]

The bus frequency is unnecessarily converted between Hz and kHz in
several places.
This is probably an old legacy from the old times (pre-devicetrees)
when the davinci_i2c_platform_data took the bus_freq in kHz.

Stick to Hz.

Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
---
 drivers/i2c/busses/i2c-davinci.c | 18 ++++++++----------
 1 file changed, 8 insertions(+), 10 deletions(-)

diff --git a/drivers/i2c/busses/i2c-davinci.c b/drivers/i2c/busses/i2c-davinci.c
index a773ba082321..a2b578e0a534 100644
--- a/drivers/i2c/busses/i2c-davinci.c
+++ b/drivers/i2c/busses/i2c-davinci.c
@@ -117,8 +117,6 @@
 /* timeout for pm runtime autosuspend */
 #define DAVINCI_I2C_PM_TIMEOUT	1000	/* ms */
 
-#define DAVINCI_I2C_DEFAULT_BUS_FREQ	100
-
 struct davinci_i2c_dev {
 	struct device           *dev;
 	void __iomem		*base;
@@ -134,8 +132,8 @@ struct davinci_i2c_dev {
 #ifdef CONFIG_CPU_FREQ
 	struct notifier_block	freq_transition;
 #endif
-	/* standard bus frequency (kHz) */
-	unsigned int		bus_freq;
+	/* standard bus frequency */
+	unsigned int		bus_freq_hz;
 	/* Chip has a ICPFUNC register */
 	bool			has_pfunc;
 };
@@ -209,16 +207,16 @@ static void i2c_davinci_calc_clk_dividers(struct davinci_i2c_dev *dev)
 	if (device_is_compatible(dev->dev, "ti,keystone-i2c"))
 		d = 6;
 
-	clk = ((input_clock / (psc + 1)) / (dev->bus_freq * 1000));
+	clk = ((input_clock / (psc + 1)) / (dev->bus_freq_hz));
 	/* Avoid driving the bus too fast because of rounding errors above */
-	if (input_clock / (psc + 1) / clk > dev->bus_freq * 1000)
+	if (input_clock / (psc + 1) / clk > dev->bus_freq_hz)
 		clk++;
 	/*
 	 * According to I2C-BUS Spec 2.1, in FAST-MODE LOW period should be at
 	 * least 1.3uS, which is not the case with 50% duty cycle. Driving HIGH
 	 * to LOW ratio as 1 to 2 is more safe.
 	 */
-	if (dev->bus_freq > 100)
+	if (bus_freq_hz > I2C_MAX_STANDARD_MODE_FREQ)
 		clkl = (clk << 1) / 3;
 	else
 		clkl = (clk >> 1);
@@ -269,7 +267,7 @@ static int i2c_davinci_init(struct davinci_i2c_dev *dev)
 		davinci_i2c_read_reg(dev, DAVINCI_I2C_CLKL_REG));
 	dev_dbg(dev->dev, "CLKH = %d\n",
 		davinci_i2c_read_reg(dev, DAVINCI_I2C_CLKH_REG));
-	dev_dbg(dev->dev, "bus_freq = %dkHz\n", dev->bus_freq);
+	dev_dbg(dev->dev, "bus_freq_hz = %dHz\n", dev->bus_freq_hz);
 
 
 	/* Take the I2C module out of reset: */
@@ -760,9 +758,9 @@ static int davinci_i2c_probe(struct platform_device *pdev)
 
 	r = device_property_read_u32(&pdev->dev, "clock-frequency", &prop);
 	if (r)
-		prop = DAVINCI_I2C_DEFAULT_BUS_FREQ;
+		prop = I2C_MAX_STANDARD_MODE_FREQ;
 
-	dev->bus_freq = prop / 1000;
+	dev->bus_freq_hz = prop;
 
 	dev->has_pfunc = device_property_present(&pdev->dev, "ti,has-pfunc");
 

-- 
2.52.0

[PATCH v7 4/5] i2c: davinci: add support for setting bus frequency

[Marcus Folkesson]

Populate adapter with clock_hz and set_clk_freq to enable support for
dynamic bus frequency.

Remove bus_freq_hz entirely and only use clock_hz instead.

Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
---
 drivers/i2c/busses/i2c-davinci.c | 36 +++++++++++++++++++++++++++++-------
 1 file changed, 29 insertions(+), 7 deletions(-)

diff --git a/drivers/i2c/busses/i2c-davinci.c b/drivers/i2c/busses/i2c-davinci.c
index a2b578e0a534..96b78014aa51 100644
--- a/drivers/i2c/busses/i2c-davinci.c
+++ b/drivers/i2c/busses/i2c-davinci.c
@@ -132,8 +132,6 @@ struct davinci_i2c_dev {
 #ifdef CONFIG_CPU_FREQ
 	struct notifier_block	freq_transition;
 #endif
-	/* standard bus frequency */
-	unsigned int		bus_freq_hz;
 	/* Chip has a ICPFUNC register */
 	bool			has_pfunc;
 };
@@ -171,6 +169,8 @@ static void i2c_davinci_calc_clk_dividers(struct davinci_i2c_dev *dev)
 	u32 clkh;
 	u32 clkl;
 	u32 input_clock = clk_get_rate(dev->clk);
+	u32 bus_freq_hz = dev->adapter.clock_hz;
+
 
 	/* NOTE: I2C Clock divider programming info
 	 * As per I2C specs the following formulas provide prescaler
@@ -207,9 +207,9 @@ static void i2c_davinci_calc_clk_dividers(struct davinci_i2c_dev *dev)
 	if (device_is_compatible(dev->dev, "ti,keystone-i2c"))
 		d = 6;
 
-	clk = ((input_clock / (psc + 1)) / (dev->bus_freq_hz));
+	clk = ((input_clock / (psc + 1)) / (bus_freq_hz));
 	/* Avoid driving the bus too fast because of rounding errors above */
-	if (input_clock / (psc + 1) / clk > dev->bus_freq_hz)
+	if (input_clock / (psc + 1) / clk > bus_freq_hz)
 		clk++;
 	/*
 	 * According to I2C-BUS Spec 2.1, in FAST-MODE LOW period should be at
@@ -267,7 +267,7 @@ static int i2c_davinci_init(struct davinci_i2c_dev *dev)
 		davinci_i2c_read_reg(dev, DAVINCI_I2C_CLKL_REG));
 	dev_dbg(dev->dev, "CLKH = %d\n",
 		davinci_i2c_read_reg(dev, DAVINCI_I2C_CLKH_REG));
-	dev_dbg(dev->dev, "bus_freq_hz = %dHz\n", dev->bus_freq_hz);
+	dev_dbg(dev->dev, "bus_freq_hz = %dHz\n", dev->adapter.clock_hz);
 
 
 	/* Take the I2C module out of reset: */
@@ -279,6 +279,27 @@ static int i2c_davinci_init(struct davinci_i2c_dev *dev)
 	return 0;
 }
 
+static int davinci_i2c_set_clk(struct i2c_adapter *adap, u32 clock_hz)
+{
+	struct davinci_i2c_dev *dev = i2c_get_adapdata(adap);
+
+	if (adap->clock_hz == clock_hz)
+		return 0;
+
+	adap->clock_hz = clock_hz;
+
+	/* put I2C into reset */
+	davinci_i2c_reset_ctrl(dev, 0);
+
+	/* compute clock dividers */
+	i2c_davinci_calc_clk_dividers(dev);
+
+	/* Take the I2C module out of reset: */
+	davinci_i2c_reset_ctrl(dev, 1);
+
+	return 0;
+}
+
 /*
  * This routine does i2c bus recovery by using i2c_generic_scl_recovery
  * which is provided by I2C Bus recovery infrastructure.
@@ -755,12 +776,13 @@ static int davinci_i2c_probe(struct platform_device *pdev)
 	dev->dev = &pdev->dev;
 	dev->irq = irq;
 	platform_set_drvdata(pdev, dev);
+	adap = &dev->adapter;
 
 	r = device_property_read_u32(&pdev->dev, "clock-frequency", &prop);
 	if (r)
 		prop = I2C_MAX_STANDARD_MODE_FREQ;
 
-	dev->bus_freq_hz = prop;
+	adap->clock_hz = prop;
 
 	dev->has_pfunc = device_property_present(&pdev->dev, "ti,has-pfunc");
 
@@ -800,7 +822,6 @@ static int davinci_i2c_probe(struct platform_device *pdev)
 		goto err_unuse_clocks;
 	}
 
-	adap = &dev->adapter;
 	i2c_set_adapdata(adap, dev);
 	adap->owner = THIS_MODULE;
 	adap->class = I2C_CLASS_DEPRECATED;
@@ -809,6 +830,7 @@ static int davinci_i2c_probe(struct platform_device *pdev)
 	adap->dev.parent = &pdev->dev;
 	adap->timeout = DAVINCI_I2C_TIMEOUT;
 	adap->dev.of_node = dev_of_node(&pdev->dev);
+	adap->set_clk_freq = davinci_i2c_set_clk;
 
 	if (dev->has_pfunc)
 		adap->bus_recovery_info = &davinci_i2c_scl_recovery_info;

-- 
2.52.0

[PATCH v7 5/5] docs: i2c: i2c-topology: add section about bus speed

[Marcus Folkesson]

Describe what needs to be consideraed and taken into account
when using different bus speeds for different mux channels.

Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
---
 Documentation/i2c/i2c-topology.rst | 178 +++++++++++++++++++++++++++++++++++++
 1 file changed, 178 insertions(+)

diff --git a/Documentation/i2c/i2c-topology.rst b/Documentation/i2c/i2c-topology.rst
index 48fce0f7491b..24df553ca8c7 100644
--- a/Documentation/i2c/i2c-topology.rst
+++ b/Documentation/i2c/i2c-topology.rst
@@ -367,6 +367,184 @@ When D1 or D2 are accessed, accesses to D3 and D4 are locked out while
 accesses to D5 may interleave. When D3 or D4 are accessed, accesses to
 all other devices are locked out.
 
+Bus Speed and I2C Multiplexers
+================================
+
+I2C bus multiplexers allow multiple downstream channels to be exposed
+as separate I2C adapters which also could set their own bus speed.
+
+The multiplexer itself cannot change the bus speed as it use the upstream
+clock and data lines to communicate with the downstream devices. The speed
+is therefore changed in the root adapter resulting in that the whole bus is
+affected.
+
+This increases the complexity of the topology and some considerations must
+be taken into account.
+
+Bus speed
+----------
+
+Downstream channels of an I2C multiplexer can only operate at the same or
+lower bus speed as the upstream bus. This is because the upstream bus may
+have devices that cannot operate at higher speeds and those will be affected
+by the speed change.
+
+The example below illustrates the problem.
+The root adapter is operating at 100kHz. D2 can only operate with 100kHz,
+but D1 can operate at 400kHz. When D1 is selected, the bus speed of the
+root adapter would have to be set to 400kHz, a speed that D2 may not support.
+
+This topology is therefor not allowed: ::
+
+                          .----------. 400kHz .--------.
+        .--------. 100kHz |   mux-   |--------| dev D1 |
+        |  root  |--+-----|  locked  |        '--------'
+        '--------'  |     |  mux M1  |
+                    |     '----------'
+                    |  .--------.
+                    '--| dev D2 |
+                       '--------'
+
+
+This topology is allowed: ::
+
+                          .----------. 100kHz .--------.
+        .--------. 400kHz |   mux-   |--------| dev D2 |
+        |  root  |--+-----|  locked  |        '--------'
+        '--------'        |  mux M1  |--. 400kHz .--------.
+                          '----------'  '--------| dev D1 |
+                                                 '--------'
+
+Preferred topology
+-------------------
+
+The preferred topology when using different bus speeds is to have the multiplexer
+connected directly to the root adapter without any devices as siblings.
+By this arrangement, the bus speed can be changed without affecting any other devices
+and many of the caveats are avoided.
+
+Other multiplexers in parallel is still okay as those are locked out during transfers.
+
+This is the preferred topology: ::
+
+                          .----------. 100kHz .--------.
+        .--------. 400kHz |   mux-   |--------| dev D2 |
+        |  root  |--+-----|  locked  |        '--------'
+        '--------'        |  mux M1  |--. 400kHz .--------.
+                          '----------'  '--------| dev D1 |
+                                                 '--------'
+
+Locking
+--------
+
+If the multiplexer is mux-locked, transfers to D3 may interleave between the
+select-transfer-deselect to D1 or D2.
+This results in a situation where the bus speed to D3 may be lower than it
+is supposed to be. This is usually not a problem.
+
+This topology is allowed but some transfers to D3 may be at 100kHz: ::
+
+                          .----------. 100kHz .--------.
+        .--------. 400kHz |   mux-   |--------| dev D1 |
+        |  root  |--+-----|  locked  |        '--------'
+        '--------'  |     |  mux M1  |--. 400kHz .--------.
+                    |     '----------'  '--------| dev D2 |
+                    |  .--------.                '--------'
+                    '--| dev D3 |
+                       '--------'
+
+Multiple muxes in series
+--------------------------
+
+When multiple muxes are used in series the same rules applies.
+
+Transfers to D3 may interleave between select-transfer-deselect to D1, which
+results that the bus speed to D2 or D3 will be at 100KHz.
+
+Transfers to D2 may interleave between select-transfer-deselect to D1, which
+results in that the bus speed to D1 may be at 400kHz as the transfer to D2
+will set the bus speed to before the transfer to D1 starts.
+
+This is probably a bad topology ::
+
+                     .----------. 400kHz .----------. 100kHz .--------.
+    .--------.400kHz |   mux-   |--------|   mux-   |--------| dev D1 |
+    |  root  |--+----|  locked  | 400kHz |  locked  |        '--------'
+    '--------'  |    |  mux M1  |--.     |  mux M2  |
+                |    '----------'  |     '----------'
+                |  .--------.      |  .--------.
+                '--| dev D3 |      '--| dev D2 |
+                   '--------'         '--------'
+
+Multiple muxes in parallel
+----------------------------
+
+When multiple muxes are used in parallel all access to other muxes are locked out
+so this is not a problem.
+
+If the muxes are mux-locked, access to D3 may still interleave though.
+
+In the example below, D3 may not interleave between select-transfer-deselect for D1
+or D2 as both muxes are parent-locked: ::
+
+
+                   .----------. 100kHz   .--------.
+                   |  parent- |----------| dev D1 |
+                .--|  locked  |          '--------'
+                |  |  mux M1  |
+                |  '----------'
+                |      .----------. 400KHz  .--------.
+    .--------. 400kHz  |  parent- |---------| dev D2 |
+    |  root  |--+------|  locked  |         '--------'
+    '--------'  |      |  mux M2  |
+                |      '----------'
+                |  .--------.
+                '--| dev D3 |
+                   '--------'
+
+Idle state
+-----------
+
+Muxes have an idle state, which is the state the channels are put into when no channel
+is active. The state is typically one of the following:
+
+- All channels are disconnected
+- The last selected channel is left as-is
+- A predefined channel is selected
+
+Muxes that support an idle state where all channels are disconnected are preferred when using
+different bus speeds. Otherwise high bus speeds may "leak" through to devices that
+may not support that higher speed.
+
+Consider the following example: ::
+
+                          .----------. 100kHz .--------.
+        .--------. 400kHz |   mux-   |--------| dev D1 |
+        |  root  |--+-----|  locked  |        '--------'
+        '--------'  |     |  mux M1  |--. 400kHz .--------.
+                    |     '----------'  '--------| dev D2 |
+                    |  .--------.                '--------'
+                    '--| dev D3 |
+                       '--------'
+
+If the idle state of M1 is:
+
+- All channels disconnected: No problem, D1 and D2 are not affected by communication
+  to D3.
+- Last selected channel: Problem if D1 was the last selected channel. High speed
+  communication to D3 will be "leaked" to D1.
+- Predefined channel: Problem if the predefined channel D1. Set predefined channel
+  to D2 as D2 may handle 400kHz.
+
+Supported controllers
+-----------------------
+
+Not all I2C controllers support setting the bus speed dynamically.
+At the time of writing, the following controllers have support:
+
+============================   =============================================
+i2c-davinci                    Supports dynamic bus speed
+============================   =============================================
 
 Mux type of existing device drivers
 ===================================

-- 
2.52.0

Re: [PATCH v7 1/5] i2c: core: add callback to change bus frequency

[Andy Shevchenko]

On Mon, Feb 23, 2026 at 03:33:50PM +0100, Marcus Folkesson wrote:
> All devices on the same I2C bus share the same clock line and the bus
> frequency has therefor be chosen so that all attached devices are able
> to tolarate that clock rate. IOW, the bus speed must be set for the
> slowest attached device.
> 
> With I2C multiplexers/switches on the other hand, it would be possible
> to have different "domains" that runs with different speeds.
> 
> Prepare for such a feature by provide an optional callback function to
> change bus frequency.
> 
> As a side effect, several bus drivers keep the bus speed in a
> private structure and can now have this value stored in a uniform way
> instead.

...

> +	/*
> +	 * If the adapter is a root adapter without set_clk_freq implemented, this feature is not
> +	 * supported
> +	 */
> +	if (!i2c_parent_is_i2c_adapter(adapter))
> +		return -EOPNOTSUPP;
> +
> +	/* Update the clock_hz for non-root adapters, even if set_clk_freq is not implemented,
> +	 * to allow * the clock frequency to be propagated to root adapters that do support it.
> +	 */

/*
 * Please, keep the style of multi-line comment consistent
 * and as per above.
 */

> +	adapter->clock_hz = clock_hz;
> +	return 0;
> +}

-- 
With Best Regards,
Andy Shevchenko

Re: [PATCH v7 1/5] i2c: core: add callback to change bus frequency

[Andy Shevchenko]

On Mon, Feb 23, 2026 at 04:54:01PM +0200, Andy Shevchenko wrote:
> On Mon, Feb 23, 2026 at 03:33:50PM +0100, Marcus Folkesson wrote:

...

> > +	/*
> > +	 * If the adapter is a root adapter without set_clk_freq implemented, this feature is not

.set_clk_freq()

> > +	 * supported

Please, also respect English grammar and punctuation: Missed period here.

> > +	 */
> > +	if (!i2c_parent_is_i2c_adapter(adapter))
> > +		return -EOPNOTSUPP;
> > +
> > +	/* Update the clock_hz for non-root adapters, even if set_clk_freq is not implemented,

.set_clk_freq()

> > +	 * to allow * the clock frequency to be propagated to root adapters that do support it.
> > +	 */
> 
> /*
>  * Please, keep the style of multi-line comment consistent
>  * and as per above.

...including one thing ^^^

>  */
> 
> > +	adapter->clock_hz = clock_hz;
> > +	return 0;

-- 
With Best Regards,
Andy Shevchenko

Re: [PATCH v7 2/5] i2c: mux: add support for per channel bus frequency

[Andy Shevchenko]

On Mon, Feb 23, 2026 at 03:33:51PM +0100, Marcus Folkesson wrote:
> There may be several reasons why you may need to use a certain speed
> on an I2C bus. E.g.
> 
> - When several devices are attached to the bus, the speed must be
>   selected according to the slowest device.
> 
> - Electrical conditions may limit the usuable speed on the bus for
>   different reasons.
> 
> With an I2C multiplexer, it is possible to group the attached devices
> after their preferred speed by e.g. put all "slow" devices on a separate
> channel on the multiplexer.
> 
> Consider the following topology:
> 
>                       .----------. 100kHz .--------.
>     .--------. 400kHz |          |--------| dev D1 |
>     |  root  |--+-----| I2C MUX  |        '--------'
>     '--------'  |     |          |--. 400kHz .--------.
>                 |     '----------'  '-------| dev D2 |
>                 |  .--------.               '--------'
>                 '--| dev D3 |
>                    '--------'
> 
> One requirement with this design is that a multiplexer may only use the
> same or lower bus speed as its parent.
> Otherwise, if the multiplexer would have to increase the bus frequency,
> then all siblings (D3 in this case) would run into a clock speed it may
> not support.
> 
> The bus frequency for each channel is set in the devicetree. As the
> i2c-mux bindings import the i2c-controller schema, the clock-frequency
> property is already allowed.
> If no clock-frequency property is set, the channel inherit their parent
> bus speed.
> 
> The following example uses dt bindings to illustrate the topology above:
> 
>     i2c {
> 	clock-frequency = <400000>;
> 
>         i2c-mux {
>             i2c@0 {
>                 clock-frequency = <100000>;
> 
>                 D1 {
>                     ...
>                 };
>             };
> 
>             i2c@1 {
>                 D2 {
>                   ...
>                 };
>             };
>         };
> 
>         D3 {
>             ...
>         }
>     };

...

> +static int i2c_mux_select_chan(struct i2c_adapter *adap, u32 chan_id, u32 *oldclock)
> +{
> +	struct i2c_mux_priv *priv = adap->algo_data;
> +	struct i2c_mux_core *muxc = priv->muxc;
> +	struct i2c_adapter *parent = muxc->parent;
> +	int ret;
> +
> +	if (priv->adap.clock_hz && priv->adap.clock_hz < parent->clock_hz) {
> +		*oldclock = parent->clock_hz;
> +
> +		if (muxc->mux_locked)
> +			ret = i2c_adapter_set_clk_freq(parent, priv->adap.clock_hz);
> +		else
> +			ret = __i2c_adapter_set_clk_freq(parent, priv->adap.clock_hz);
> +
> +		dev_dbg(&adap->dev, "Set clock frequency %dHz on %s\n",
> +			priv->adap.clock_hz, parent->name);

%u

> +		if (ret)
> +			dev_err(&adap->dev,
> +				"Failed to set clock frequency %dHz on adapter %s: %d\n",
> +				*oldclock, parent->name, ret);

%u

Oh, and so on...

Please, carefully inspect all printf() specifiers in the patches.

> +	}
> +
> +	return muxc->select(muxc, priv->chan_id);
> +}

-- 
With Best Regards,
Andy Shevchenko

Re: [PATCH v7 3/5] i2c: davinci: calculate bus freq from Hz instead of kHz

[Andy Shevchenko]

On Mon, Feb 23, 2026 at 03:33:52PM +0100, Marcus Folkesson wrote:
> The bus frequency is unnecessarily converted between Hz and kHz in
> several places.
> This is probably an old legacy from the old times (pre-devicetrees)
> when the davinci_i2c_platform_data took the bus_freq in kHz.
> 
> Stick to Hz.

...

> -	clk = ((input_clock / (psc + 1)) / (dev->bus_freq * 1000));
> +	clk = ((input_clock / (psc + 1)) / (dev->bus_freq_hz));

Two pairs too many parentheses!

	clk = (input_clock / (psc + 1)) / dev->bus_freq_hz;

...

> +	dev_dbg(dev->dev, "bus_freq_hz = %dHz\n", dev->bus_freq_hz);

%u ?

-- 
With Best Regards,
Andy Shevchenko

Re: [PATCH v7 4/5] i2c: davinci: add support for setting bus frequency

[Andy Shevchenko]

On Mon, Feb 23, 2026 at 03:33:53PM +0100, Marcus Folkesson wrote:
> Populate adapter with clock_hz and set_clk_freq to enable support for

.set_clk_freq()

> dynamic bus frequency.
> 
> Remove bus_freq_hz entirely and only use clock_hz instead.


-- 
With Best Regards,
Andy Shevchenko

Re: [PATCH v7 3/5] i2c: davinci: calculate bus freq from Hz instead of kHz

[Marcus Folkesson]

[-- Attachment #1: Type: text/plain, Size: 1044 bytes --]

Hi Andy,

On Mon, Feb 23, 2026 at 04:59:49PM +0200, Andy Shevchenko wrote:
> On Mon, Feb 23, 2026 at 03:33:52PM +0100, Marcus Folkesson wrote:
> > The bus frequency is unnecessarily converted between Hz and kHz in
> > several places.
> > This is probably an old legacy from the old times (pre-devicetrees)
> > when the davinci_i2c_platform_data took the bus_freq in kHz.
> > 
> > Stick to Hz.
> 
> ...
> 
> > -	clk = ((input_clock / (psc + 1)) / (dev->bus_freq * 1000));
> > +	clk = ((input_clock / (psc + 1)) / (dev->bus_freq_hz));
> 
> Two pairs too many parentheses!
> 
> 	clk = (input_clock / (psc + 1)) / dev->bus_freq_hz;
> 
> ...
> 
> > +	dev_dbg(dev->dev, "bus_freq_hz = %dHz\n", dev->bus_freq_hz);
> 
> %u ?


Thank you for your comments, both this and the other.

This driver has a a few  other style & formatting issues, would you prefer
to fix those in a separate patch in this patchset or in a following one?

> 
> -- 
> With Best Regards,
> Andy Shevchenko
> 
> 

Thanks,
Marcus Folkesson

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

Re: [PATCH v7 3/5] i2c: davinci: calculate bus freq from Hz instead of kHz

[Andy Shevchenko]

On Mon, Mar 09, 2026 at 12:14:15PM +0100, Marcus Folkesson wrote:
> On Mon, Feb 23, 2026 at 04:59:49PM +0200, Andy Shevchenko wrote:
> > On Mon, Feb 23, 2026 at 03:33:52PM +0100, Marcus Folkesson wrote:

...

> > > +	dev_dbg(dev->dev, "bus_freq_hz = %dHz\n", dev->bus_freq_hz);
> > 
> > %u ?
> 
> Thank you for your comments, both this and the other.
> 
> This driver has a a few  other style & formatting issues, would you prefer
> to fix those in a separate patch in this patchset or in a following one?

Depending on the issues and churn it makes.

In cases you already touched the lines these (what I mentioned) can be done at
the same time as they do not change the logic. (Yes, theoretically you may get
-BIG NUMBER for big frequencies, but I do not believe we have 2+GHz for any I²C
controller in the world, so IRL it's close to impossible.)


-- 
With Best Regards,
Andy Shevchenko