From: Brian Masney <bmasney@redhat.com>
To: Joey Lu <a0987203069@gmail.com>
Cc: mturquette@baylibre.com, sboyd@kernel.org, ychuang3@nuvoton.com,
schung@nuvoton.com, yclu4@nuvoton.com,
linux-arm-kernel@lists.infradead.org, linux-clk@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH 1/1] clk: nuvoton: ma35d1: fix PLL frequency calculation
Date: Mon, 11 May 2026 11:54:16 -0400 [thread overview]
Message-ID: <agH7qJypv48vkZOr@redhat.com> (raw)
In-Reply-To: <20260511031600.31929-2-a0987203069@gmail.com>
Hi Joey,
On Mon, May 11, 2026 at 11:15:59AM +0800, Joey Lu wrote:
> Fix four bugs in the MA35D1 PLL driver:
>
> 1. PLL_CTL1_FRAC was defined as GENMASK(31, 24) (8 bits), but the
> hardware fractional field spans bits [31:8] (24 bits). This caused
> wrong frequency calculation in fractional and spread-spectrum modes.
>
> 2. div_u64() does not modify its argument in-place; the quotient must
> be assigned from the return value. Both ma35d1_calc_smic_pll_freq()
> and ma35d1_calc_pll_freq() discarded the return value, leaving
> pll_freq undivided and orders of magnitude too high.
>
> 3. The fractional-mode calculation divided x by FIELD_MAX(PLL_CTL1_FRAC)
> to get 2 decimal digits. After correcting the mask to 24 bits, update
> the arithmetic to use 3 decimal digits with proper 24-bit fixed-point
> rounding.
>
> 4. ma35d1_clk_pll_determine_rate() called ma35d1_pll_find_closest()
> unconditionally before the switch, but then overwrote its result by
> reading the current hardware registers for every PLL type. Move the
> find_closest() call inside the configurable-PLL branch (APLL, EPLL,
> VPLL). CAPLL and DDRPLL do not support runtime rate changes and
> correctly return the current hardware rate.
>
> Fixes: 691521a367cf ("clk: nuvoton: Add clock driver for ma35d1 clock controller")
> Signed-off-by: Joey Lu <a0987203069@gmail.com>
Thanks for the patch, however this should really be broken up into more
patches. If possible, one patch for each of the fixes.
Brian
> ---
> drivers/clk/nuvoton/clk-ma35d1-pll.c | 34 +++++++++++++--------------
> 1 file changed, 17 insertions(+), 17 deletions(-)
>
> diff --git a/drivers/clk/nuvoton/clk-ma35d1-pll.c b/drivers/clk/nuvoton/clk-ma35d1-pll.c
> index 4620acfe47e8..314b81e7727c 100644
> --- a/drivers/clk/nuvoton/clk-ma35d1-pll.c
> +++ b/drivers/clk/nuvoton/clk-ma35d1-pll.c
> @@ -48,7 +48,7 @@
> #define PLL_CTL1_PD BIT(0)
> #define PLL_CTL1_BP BIT(1)
> #define PLL_CTL1_OUTDIV GENMASK(6, 4)
> -#define PLL_CTL1_FRAC GENMASK(31, 24)
> +#define PLL_CTL1_FRAC GENMASK(31, 8)
> #define PLL_CTL2_SLOPE GENMASK(23, 0)
>
> #define INDIV_MIN 1
> @@ -92,7 +92,7 @@ static unsigned long ma35d1_calc_smic_pll_freq(u32 pll0_ctl0,
> p = FIELD_GET(SPLL0_CTL0_OUTDIV, pll0_ctl0);
> outdiv = 1 << p;
> pll_freq = (u64)parent_rate * n;
> - div_u64(pll_freq, m * outdiv);
> + pll_freq = div_u64(pll_freq, m * outdiv);
> return pll_freq;
> }
>
> @@ -110,12 +110,12 @@ static unsigned long ma35d1_calc_pll_freq(u8 mode, u32 *reg_ctl, unsigned long p
>
> if (mode == PLL_MODE_INT) {
> pll_freq = (u64)parent_rate * n;
> - div_u64(pll_freq, m * p);
> + pll_freq = div_u64(pll_freq, m * p);
> } else {
> x = FIELD_GET(PLL_CTL1_FRAC, reg_ctl[1]);
> - /* 2 decimal places floating to integer (ex. 1.23 to 123) */
> - n = n * 100 + ((x * 100) / FIELD_MAX(PLL_CTL1_FRAC));
> - pll_freq = div_u64(parent_rate * n, 100 * m * p);
> + /* x is 24-bit fractional part, convert to 3 decimal digits */
> + n = n * 1000 + (u32)(((u64)x * 1000 + 500) >> 24);
> + pll_freq = div_u64((u64)parent_rate * n, 1000 * m * p);
> }
> return pll_freq;
> }
> @@ -255,32 +255,32 @@ static int ma35d1_clk_pll_determine_rate(struct clk_hw *hw,
> if (req->best_parent_rate < PLL_FREF_MIN_FREQ || req->best_parent_rate > PLL_FREF_MAX_FREQ)
> return -EINVAL;
>
> - ret = ma35d1_pll_find_closest(pll, req->rate, req->best_parent_rate,
> - reg_ctl, &pll_freq);
> - if (ret < 0)
> - return ret;
> -
> switch (pll->id) {
> case CAPLL:
> + case DDRPLL:
> + /* Read-only PLLs: return current rate */
> reg_ctl[0] = readl_relaxed(pll->ctl0_base);
> - pll_freq = ma35d1_calc_smic_pll_freq(reg_ctl[0], req->best_parent_rate);
> + if (pll->id == CAPLL) {
> + pll_freq = ma35d1_calc_smic_pll_freq(reg_ctl[0], req->best_parent_rate);
> + } else {
> + reg_ctl[1] = readl_relaxed(pll->ctl1_base);
> + pll_freq = ma35d1_calc_pll_freq(pll->mode, reg_ctl, req->best_parent_rate);
> + }
> req->rate = pll_freq;
> -
> return 0;
> - case DDRPLL:
> case APLL:
> case EPLL:
> case VPLL:
> - reg_ctl[0] = readl_relaxed(pll->ctl0_base);
> - reg_ctl[1] = readl_relaxed(pll->ctl1_base);
> - pll_freq = ma35d1_calc_pll_freq(pll->mode, reg_ctl, req->best_parent_rate);
> + /* Configurable PLLs: find closest achievable rate */
> + ret = ma35d1_pll_find_closest(pll, req->rate, req->best_parent_rate,
> + reg_ctl, &pll_freq);
> + if (ret < 0)
> + return ret;
> req->rate = pll_freq;
> -
> return 0;
> }
>
> req->rate = 0;
> -
> return 0;
> }
>
> --
> 2.49.0
next prev parent reply other threads:[~2026-05-11 15:54 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-05-11 3:15 [PATCH 0/1] clk: nuvoton: ma35d1: fix PLL frequency calculation Joey Lu
2026-05-11 3:15 ` [PATCH 1/1] " Joey Lu
2026-05-11 15:54 ` Brian Masney [this message]
2026-05-12 3:49 ` Joey Lu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=agH7qJypv48vkZOr@redhat.com \
--to=bmasney@redhat.com \
--cc=a0987203069@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mturquette@baylibre.com \
--cc=sboyd@kernel.org \
--cc=schung@nuvoton.com \
--cc=ychuang3@nuvoton.com \
--cc=yclu4@nuvoton.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox